5 Tips To Help You Safely Use A Table Saw. Table saw kickback injury

Tips To Help You Safely Use A Table Saw

The table saw is one of the most used woodworking tools in the U.S., popular among professionals and DIY enthusiasts. In fact, statistics show that nearly 10 million table saw machines are used in home workshops across the U.S. The table saw is central to any woodworking shop; it features a circular blade that is powered by a motor, delivering accurate and precise cuts. While this instrument is valuable to woodworkers, it is also the most dangerous, causing severe injuries to many operators yearly.

According to Chaffin Luhana LLP, table saw injuries amount to about 67,000 cases, causing an estimated 2.1 billion in medical fees annually. With that said, does it mean that you cannot use this tool whatsoever? Absolutely not! It is worth mentioning that safety begins with you, and by taking some simple precautionary measures, you should be able to keep yourself out of harm’s way. Most of the table saw-related injuries are caused by negligence by the user. Here are a few tips and tricks that should help you avoid injuries when using a table saw.

Use a push stick

No doubt using a table saw always comes with an element of danger; think about it, you are pushing a piece of wood in the direction of a spinning blade. You need protection to keep your fingers safe; that is where a push stick comes in. A standard table saw comes with a single push stick which is enough for the most part. But two dangers are associated with a table saw: injury caused by the blade and harm due to kickback action. Woodworking for Mere Mortals details that a kickback occurs when the blade grabs the piece of material and throws it back in your direction, causing fatal injuries.

Kickbacks might not cause injuries every time; in some scenarios, they may result in irregularly cut wood, leaving you with disappointing results. One way of keeping yourself safe from kickbacks is using a push stick. A push stick keeps your hands far from the blade, and in the event of a kickback, your fingers won’t get drawn to the sharp edge. over, a push stick gives you better control of the workpiece you are cutting, reducing the risk of kickbacks and allowing you to make precise cuts.

Do not use gloves

Outside the workshop, gloves are good for all the right reasons; they keep hands warm during winter and germs away. However, when it comes to working with table saws, there is no room for gloves whatsoever. You can wear gloves when doing other activities in the workshop, for instance, handling wood in the initial stages. However, wearing gloves is likely to cause more harm than good when using a table saw. This is because woodwork operation with the table saw heavily depends on the craftsman’s sense of touch.

Wearing gloves means you cannot feel the board’s movement; therefore, you may have a delayed response to critical situations. Also another danger of using gloves when handling a table saw is that the fabric can get caught on the blades causing even more damage. Essentially, it is proper to avoid wearing gloves when using any tool with a rotating blade, via the Ohio State University Extension. Remember, cut-proof gloves will not stop the table saw from doing what it is meant to do, which is to cut!

Use featherboards

Although not emphasized enough, a featherboard is an invaluable piece of equipment that every woodworker must have. According to Rockler, the featherboard serves two main purposes, holding the workpiece firmly against the fence and providing extra safety to the operator. When working with a table saw, there is always a risk of kickback causing injuries to the operator. When a featherboard is correctly placed on the table, it applies constant pressure to the workpiece allowing you to make precise and accurate cuts while at the same time preventing the possibility of a kickback.

Because of the featherboard fingers’ orientation, it should be easier to push the workpiece forward than it is to drive back. This mechanism is responsible for keeping the workpiece firmly on the track. While recent table saws come with a standard featherboard, you can make one right in your workshop. DIY featherboards are more comfortable and user-friendly, and you won’t incur any costs.

Adopt proper positioning or stance

Part of the safety measures when using the table saw, and any other equipment for that matter, is stability during operation. The proper stance that gives you the most solidity is standing with your feet a few feet apart. Avoid standing with your feet together or leaning on one foot while operating the table saw. When it comes to positioning, avoid standing right behind the table; instead, work on the piece from the side.

This will ensure you don’t get hit by the workpiece if a kickback happens during operation. ShakeDeal advises that the correct positioning while operating the table saw is to the left of the blade. This position is quite strategic because it is comfortable for the operation, putting the blade between the fence and the operator. Lastly, if the positioning of your arm doesn’t feel comfortable or is unnatural, don’t force it. Step back, rethink, and adjust your stance. It is better to be safe than sorry.

Use the right blade

As cliché as it may sound, a sharp blade is always a safer blade; therefore, before beginning any cut, be sure that the edge you are using is honed and ready for the task. A blunt blade is also very slow and will consume much energy to cut the same workpiece. For an untrained eye, it can be difficult to tell if your blade is dull. However, ToolBoxToday mentions that if you notice burn marks that did not previously exist or you are finding it hard following cut lines, chances are you are using a dull blade. Something else to consider is to use the right blade for the right cut.

Some accidents occur because the woodworker deliberately decides to switch blades and use them on the wrong workpiece. A good example is a scenario where one chooses to use a blade for ripping to cross-cut. This is quite dangerous because the blade will likely break and cause the projectiles to fly in different directions, causing severe injury to whoever is in the way.

Don’t be a dummy by making these mistakes when using your tools! Here you’ll find some best practices to avoid common tool injuries in your home workshop.

Family Handyman

What’s the best way to demonstrate really dangerous tool practices without taking the risk of hurting someone? With a crash test dummy, of course! It’s just not easy to explain stupid techniques using words alone. That’s where our dummy, Nigel, comes in!

Every year, emergency rooms report 120,000 visits for injuries caused by four tools: table saws, circular saws, nail guns and utility knives. Add to this the 200,000 ER visits for eye injuries—a large percentage of which occur during work around the house—and it’s easy to see how we came up with this list of the most dangerous don’ts.

Our dummy, Nigel, is making some common mistakes that can result in severe injuries. But these are only a few examples of things not to do. Don’t you be a dummy! When you start on your next project, keep these don’ts in mind so you don’t become the next statistic.

Family Handyman

Don’t use the table saw fence for crosscuts

Nigel the dummy is demonstrating one of the most dangerous table saw practices: cutting a board to length using the fence as a guide. There’s a good chance the board will get pinched between the blade and the fence and get thrown back into his body with lots of force. That nasty incident is called “kickback.” Broken thumbs, cracked ribs, ruptured spleens and punctured eyes are only a few of the resultant injuries you can suffer. About 35,000 people end up in the emergency room every year with table saw injuries, with 10 percent of them hospitalized. Industry experts estimate that about half of table saw injuries are caused either directly or indirectly by kickback.

In addition to avoiding the dangerous technique Nigel is using to crosscut a board, here are a few other ways to prevent kickback injuries:

• Don’t cut anything that’s longer than it is wide with the shorter side against the fence. If you want to crosscut with a table saw, use the miter gauge or a crosscutting sled.
• Avoid ripping wet, bowed or twisted lumber.
• Position your body to the right or left of the miter saw slots, not directly behind the blade.
• Don’t let bystanders walk behind you when you’re operating the saw.

CAUTION: Don’t use the fence as a guide for crosscutting. Instead, use the miter gauge or build a crosscutting sled.

Family Handyman

Don’t remove that blade guard!

Every table saw sold includes a blade guard, which has a splitter attached. The guard covers the blade, preventing you from accidentally touching it, and the splitter keeps wood from pinching on the blade and kicking back. Don’t take them off! Sure, the guard may be a nuisance at times, but it’s better to be inconvenienced than to lose one or more fingers. Of the 35,000 emergency room visits we talked about earlier, 83 percent involve contact with the blade.

If you’re buying a table saw, consider spending extra for the SawStop brand. It’s the only saw on the market that stops the blade when skin touches it. If your blade guard is missing, contact the manufacturer for a replacement. An add-on guard like the HTC Brett-Guard (200 to 375) is a good option if your original guard is missing or doesn’t work well. If 200 sounds like too much money, ask yourself what a finger is worth.

Even with a blade guard installed, you should keep your fingers away from the blade. Always use a push stick for rips less than 4 in. wide. If you’re using your thumb to push the piece and the piece kicks back, you risk torn ligaments, tendons and broken bones. Push the cut piece past the blade, turn off the saw and wait for the blade to stop before retrieving the ripped piece. Don’t reach near a spinning blade to remove a cutoff.

CAUTION: Even a dummy should have enough common sense to avoid this technique. Nigel’s finger is so close to the blade that a split second of inattention or a kickback could send him to the crash-test dummy hospital.

Push sticks are incredibly important with a table saw. Check out this magnetic version from POWERTEC.

Family Handyman

Don’t put your hand directly behind a circular saw

There are an estimated 14,000 visits to the emergency room every year as a result of circular saw injuries. Many of these injuries result in lost or severely damaged fingers. When you’re using a circular saw, remember that if the blade binds, the saw can shoot backward a lot faster than you can move your hand out of the way. Anything in the blade’s path, including fingers, hands, legs or feet, is in danger of getting cut. Avoid the risk by clamping your work and keeping both hands on the saw whenever possible. Also keep your body to the side of the saw rather than directly behind it.

CAUTION: Don’t hold a board like this. Use a temporary nail or clamp instead. Nigel risks losing a finger or two if the saw binds.

Family Handyman

Don’t put your hands near a nail gun

Even if you’re a nail gun expert, nails don’t always go straight. Wood grain or knots can deflect the nail and cause it to shoot out the side of the board. If you’re driving the nail at an angle to toenail a board, there’s a good chance the nail can glance off and go shooting into space. If you must hold a board with your free hand, keep it well away from the nail gun muzzle. If you’re reaching over a board to hold it down, move your hand out of the nail’s path. Also avoid shooting into large knots that can deflect the nail. And, of course, always wear eye protection when you’re using a nail gun.

CAUTION: Don’t hold a board close to the nail gun tip. Move your hand as far back as possible to avoid getting a nail through your finger.

Family Handyman

Don’t be sloppy with nail guns

You’ve all seen the news stories. X-rays of big nails embedded in someone’s head, lodged in a spine or stuck in a foot. Ask any carpenter and you’re sure to hear a story about a nail that went through a finger or hand. A tool that’s powerful enough to shoot a 3-in.-long nail into wood can easily penetrate skin and bone. Depending on the type, some nail guns can be set to “bump-trip.” In this mode, the operator can simply hold down the trigger and bump the nail gun nose against the surface to shoot a nail. This is great for speeding up jobs like nailing down plywood sheathing, but it creates a risk if you hold the trigger while carrying the nail gun. Bump your leg and you’ll be heading to the emergency room. In incidents where accidental contact caused an injury, more than 80 percent of the time the operator had a finger on the trigger.

There are two ways to avoid this. First, get out your owner’s manual and see if you can set your nail gun to sequential mode. This requires you to push down the muzzle and then pull the trigger for each nail. Second, keep your hand off the trigger when you’re carrying a nail gun, or better yet, unplug the hose. Then there’s no chance of accidental firing.

CAUTION: Nigel should have disconnected the hose and kept his finger off the trigger while he went for his lunch break. You can reduce the chance of a nail gun injury by taking these two steps.

See the safety mistakes Hollywood has made over the years. Some are pretty hilarious.

Family Handyman

Don’t get careless with a knife

Power tools are one thing, but did you know that utility knives are one of the most dangerous tools, accounting for a whopping 60,000 estimated emergency room visits a year? One slip is all it takes to put a deep cut in any body part that’s in the way. And while most cuts are superficial and may only require a few stitches, permanent tendon and nerve damage is common.

The best way to avoid an injury is to clamp materials whenever possible to avoid having to hand-hold them. If you do have to hold something while you’re cutting, imagine a line at right angles to the cutting line and keep your hand behind it (on the dull side of the blade).

CAUTION: Nigel’s finger is in the danger zone. If the knife slips, he’ll end up with a nasty cut or worse. Keep your hands out of the blade’s path.

Family Handyman

Don’t risk your eyes

It’s hard to think of a good reason not to wear safety glasses, goggles or a face shield when you’re working around the house. It’s obvious that Nigel should be wearing his face shield. Of the more than 200,000 emergency room visits a year for eye injuries, at least 10,000 of them involve grinders. Browsing accident reports on the Internet will convince you of the risk. Wood chips, metal shards, bits of tile, household chemicals, paint, solvents and sticks are some of the things that injure eyes. The good news is that it’s easy to protect your vision. Just choose the right eye protection for the task at hand. For general work around the house, wear ANSI-approved safety glasses or goggles. Look on the frame for the “Z87” marking, which indicates that the glasses are rated for high impact. Wear a face shield for grinding operations. Buy several pairs of safety glasses and keep them in convenient locations so you’ll always have them on hand. Plus: Learn more bench grinder basics you need to know here.

RED ALERT: Nigel is a dummy! He’s got eye protection readily available and isn’t using it. Keep eye protection handy and don’t forget to wear it.

Every product is independently selected by our editors. If you buy something through our links, we may earn an affiliate commission.

Are Table Saws Dangerous to Used | How to Avoid Common Accidents and injuries

Table saws are one of the most dangerous tools in a woodshop. Every year, there are thousands of accidents involving table saws, and many of them result in serious injuries. In fact, the Consumer Product Safety Commission estimates that there are over 4,000 table saw-related injuries every year in the United States.

Most of these accidents could be avoided if people took the time to learn how to use their table saws safely. Unfortunately, many people think that they can just read the instruction manual and then start using the tool without any problems. However, even if you read the manual carefully, it’s still important to have someone who is experienced with table saws show you how to use it properly.

Table Saws Injuries

Most woodworkers will tell you that table saws are one of the most dangerous tools in the shop. And while that may be true, there are ways to help mitigate the risks involved with using a table saw. First and foremost, always use caution when working with any power tool.

Read the manual for your specific model before using it and follow all safety protocols. When setting up your table saw, make sure the blade is properly aligned and secured before turning on the power. Keep your hands clear of the blade at all times while it’s in operation, and never attempt to adjust or remove anything from the path of the blade while it’s running.

Be aware of kickback hazards – if the blade becomes bogged down, it can “kick back” toward you with great force. Never stand directly behind a running table saw, and always use a push stick or other device to keep your hands safely away from the blade. With proper care and attention, a table saw can be a safe and essential tool in your woodworking shop.

How Common are Table Saw Accidents?

Table saw accidents are not as common as one might think. In fact, according to the U.S. Consumer Product Safety Commission, there are an estimated 4,000 table saw-related injuries each year in the United States. However, this number is still relatively low when compared to other types of power tools and machinery.

There are a variety of reasons why table saw accidents occur. One of the most common is kickback. Kickback happens when the blade catches on something and is flung back toward the operator at high speed.

This can often happen if the material being cut isn’t fed evenly into the blade or if it’s not properly secured before cutting. Another common cause of table saw accidents is operator error. This can include anything from not using proper safety equipment to not paying attention while operating the tool.

It’s important to always be aware of what you’re doing when using any type of power tool and to follow all safety precautions that are recommended by the manufacturer. If you’re planning on using a table saw, or any other type of power tool for that matter, it’s important to be familiar with its safe operation beforehand. Accidents can happen even when all safety procedures are followed correctly, but knowing how to properly use your equipment will help reduce the risk of injury.

What is the Number One Danger When Using the Table Saw?

When it comes to table saws, the number one danger is kickback. Kickback occurs when the blade of the saw catches on the workpiece and propels it back toward the operator at high speed. This can cause serious injury or even death.

To avoid kickback, always use a push stick or other safety device to keep your hands away from the blade. never try to rip a piece of wood that is too wide for the blade; if you must cut a wide board, use a jigsaw instead. Also, be sure to wear eye and ear protection while using the table saw.

What is the Most Dangerous Woodshop Tool?

When it comes to woodshop tools, there is no one tool that is more dangerous than the others. However, there are some safety precautions that you should take when using any type of woodworking tool. Always wear eye protection and gloves when using power tools, and never use a power saw without proper training and supervision.

What’s Dangerous a Table Saw Or a Circular Saw?

There is no definitive answer to this question as it depends on a number of factors, including the operator’s experience and level of training. However, in general, table saws are considered more dangerous than circular saws because they have a larger blade that is exposed and can cause serious injuries if not used correctly. Circular saws also have smaller blade that is less likely to cause serious injuries if used incorrectly.

Are Table Saws Dangerous?

Hi, I’m john, I, ve spent my time helping people to successfully do their DIY projects.I’m a professional saw expert for over 10 years. I’m working with every type of saw and always try to find out which is best for my project. See more report this ad

Table Saw Kickback: How to Prevent It from Happening?

In the industry of woodworking, there are dangers that come with the territory. Table saw kickback is one of those dangers, and it’s important to know how to prevent it from happening. In this post, we’ll take a look at what table saw kickback is, and some tips on how to avoid it. Stay safe out there!

Table Saw Accidents

Table saw accidents are unfortunately not uncommon. In fact, the U.S. Consumer Product Safety Commission (CPSC) reports that there are an estimated 4,000 table saw-related injuries every year in the United States alone.

What is Kickback?

Kickback is a term used to describe what happens when a piece of wood is ejected from the table saw blade back towards the operator. This can happen for a number of reasons but is most often caused by either trying to cut a piece of wood that is too small, or by cutting with the grain instead of against it.

Table saw safety tips you forgot about (or never knew)

When kickback happens, it can cause serious injury or even death. In fact, the CPSC reports that kickback is responsible for the majority of table saw-related injuries.

What Is Table Saw Kickback?

Table saw kickback is when the blade of the table saw kicks back at the operator. This can happen for a number of reasons, but it usually happens because the operator is not using the table saw properly. When the blade kicks back, it can cause serious injury to the operator.

How to avoid kickback on a table saw?

Never make free-hand cuts on a table saw.

Always use the fence to guide your cuts. Kickback is a serious hazard when using a table saw, but it is preventable if you use the proper safety precautions.

Do not crosscut with the rip fence in place

The rip fence should only be used when making rip cuts (cuts along the length of the grain). When making cross cuts (cuts across the grain), use a miter gauge or a crosscut sled instead of the rip fence. This will help prevent kickbacks.

Use a push stick or other safety device

Always use a push stick or other safety device to keep your hands away from the blade. This is the best way to prevent kickbacks.

Be sure the blade is properly aligned with the fence

Make sure the blade is properly aligned with the fence before making any cuts. This will help prevent the wood from binding and kicking back.

Keep the table saw clean and free of debris

A dirty or cluttered table saw can be dangerous. Keep the saw clean and free of debris to help prevent kickback.

Be sure to wear proper safety gear, including goggles and gloves, when using the table saw. This will help protect you in case of kickbacks or other accidents.

Use the proper blade size

Use a blade that is the right size for the piece of wood you’re cutting. A blade that is too small can cause the wood to bind, and a blade that is too big can cause the wood to kick back.

Do not cut crooked stock

Crooked or irregular pieces of wood can be more likely to cause kickback. Cut these pieces of wood carefully and be sure the blade is properly aligned with the fence.

Be attentive when cutting

If you are ever unsure about a cut, or if the wood seems like it might be binding, stop cutting and ask for help from a more experienced woodworker.

The Main Points at a Glance to Avoid Kickback on a Table Saw

Have basic safety features in place: a splitter, anti-kickback pawls, and riving knives.

Always use a push stick or other safety device to keep your hands away from the blade.

Never Do This With A Circular Saw! #shorts

Be sure the blade is properly aligned with the fence.

Keep the table saw clean and free of debris.

Wear proper safety gear, including goggles and gloves.

Use a blade that is the right size for the piece of wood you’re cutting.

Be cautious when cutting small pieces of wood, as they can easily get caught in the blade and cause kickback.

When making rip cuts, keep the blade tilted towards the fence. This will help prevent the wood from binding and kicking back.

Be extra careful when cutting curved or irregular pieces of wood, as they can be more likely to cause kickback.

If you are ever unsure about a cut, or if the wood seems like it might be binding, stop cutting and ask for help from a more experienced woodworker.

Table saw kickback is a serious hazard, but it is preventable if you follow these safety tips. Always use caution when operating a table saw, and never hesitate to ask for help if you are unsure about a cut. Stay safe out there!

Table Saw Guard

One of the best ways to prevent table saw accidents is to use a guard. A properly installed and used guard can significantly reduce the risk of kickbacks and other accidents.

There are three types of guards that are typically used on table saws:

Blade guard – this is the most basic type of guard and is typically found on lower-end models. It covers the blade but does not extend down to the table surface, so it does not provide complete protection.

Anti-kickback pawls – these are located on either side of the blade and help to prevent the workpiece from being thrown back at the operator.

Splitter – this is a horizontal piece of metal that is attached to the back of the blade. It helps to keep the cut kerf from closing up and pinching the blade.

Installing a guard is not always as simple as it sounds, so be sure to consult your table saw’s owner’s manual for specific instructions.

Conclusion

Kickback is a serious hazard that can easily result in injury or death. However, it is preventable if you take the proper safety precautions. Be sure to always use a guard, never operate the saw without one, and never hesitate to ask for help if you are unsure about a cut. Stay safe out there!

Author

Nick’s woodworking expertise encompasses a wide range of skills, including basic carpentry, advanced hand cut joinery, and creative uses of power tools. He has a particular talent for furniture building and home décor projects, and is known for his attention to detail and unique design aesthetic. View all posts

What are the Dangers of Defective Table Saws?

The Consumer Product Safety Commission estimates that 87,000 people are injured each year by power saws. Table saws in particular cause grievous injuries, including amputations, lacerations, and fractures. Many power tool injuries could have been prevented by safety features that have been on the market for quite some time.

Manufacturers and distributors of power saws have a legal duty to sell safe products. Power saws that lack available safety features are considered defective. Individuals who are injured by defective table saws that lack safety features have the right to seek damages from the designers and manufacturers that failed to protect consumers.

Workers who must use table saws on the job face a number of hazards, including the following:

• Kickbacks: The wood or other stock that the saw is cutting can fly back and violently hit a worker if the circular blade catches on the stock. Dull blades are more likely to create kickback hazards.
• Projectiles: The saw can send dangerous particles flying at high speeds, including nails, splinters, woodchips, and broken saw teeth.
• Direct blade contact: Workers can lose fingers in an instant if they slip or become distracted and allow their hand to hit the blade.
• Entanglement: Loose clothing can also be pulled into a saw or nip points of the belt.

Workers may also face the risk of getting cut even when the saw is not moving, such as when they are performing machine maintenance or removing pieces of stock that are stuck in the sharp blade of the saw.

Lacerations are the most common types of injuries caused by table saws. In the worst cases, lacerations may result in amputation. Projectiles and kickbacks can also cause bruises and contusions.

How Do Table Saws Work?

Since the table saw was invented, the basic design has remained the same: a solid, spinning metal disk with a toothed edge that extends below the surface of a table. The saw cuts material that is pushed up to the blade. Today, table saws operate at speeds up to 3,000 to 4,000 revolutions per minute (RPM). Table saws are used in carpentry, construction, and in the production of wooden furniture and other types of manufacturing.

Band saws are similar in that they are also stationery. However, their blades consist of a long thin Band of toothed metal that moves using a pulley system. Generally, table saws are more dangerous to use than Band saws.

What Standards Apply to Table Saws?

The Occupational Safety and Health Administration (OSHA) publishes a number of standards for table saw safety, including:

• Vibrations: Machines should be constructed to be free from sensible vibration when run idle at full speed.
• Machine guards: Belts, pulleys, gears, shafts, and moving parts shall be guarded according to requirements.
• Hoods: Circular saws should include a hood or shield to guard workers against flying splinters or broken saw teeth.
• Power cut off: Operators should be able to cut of power without leaving their position of operation.
• Tripping: Operating treadles must be protected against unexpected or accidental tripping.

Employers are responsible for providing these and many other OSHA-mandated safety features for workers operating power saws. In addition, employers must provide safety training for workers so they can safely operate equipment and take advantage of safety features.

How Do Table Saw Safety Features Prevent Injuries?

Table saw safety features can prevent injuries in a number of ways, including the following:

• Preventing fractures, bruises, and lacerations due to kickback: Safety features, such as splitters or riving knives, can prevent the type of action, which pinches or twists a saw blade, causing the work piece to kick backwards and strike a worker. Anti-kickback pawls that can be attached to blade guards can also help prevent kickback.
• Preventing severe cuts and lacerations due to direct-blade contact. Fleshing-sensing technology can stop a cutting blade in a fraction of a second. If a finger comes in contact with a blade, this technology means that the worker may suffer a minor scratch instead of a severe laceration or amputation.
• Preventing cuts and splinters due to projectiles. Hoods and machine guards can prevent injuries from flying pieces.
• Preventing injuries due to entanglement. Machine guards and power cut-off features can prevent entanglement by belt-driven saws with exposed belts and pulleys.

Workers can also help avoid accidents by keeping the table top as clean as possible and checking the stock they are about to cut for nails, screws, and knots before cutting. Keeping the floor free of debris can also help avoid tripping accidents.

What Should a Worker Do if They are Injured by a Table Saw?

Workers injured in a table saw accident should notify their supervisor immediately. Employees who fail to provide notice of injury may lose their Workers’ Compensation benefits. Workers’ Compensation will pay for medical costs associated with a valid work-related injury as long as the employee has followed all of the procedures necessary for notifying an employer.

Workers who have any questions about this process should contact an experienced lawyer for assistance. A qualified lawyer can also provide counsel regarding the possibility of filing a third-party products liability claim.

Can an Injured Worker File a Third-Party Claim?

An employee injured by a table saw may be able to file a third-party claim to seek recovery of damages that can pay for their losses in addition to Workers’ Compensation benefits. Employees injured on the job should know that they can apply for Workers’ Compensation no matter who is at fault for the accident. On the one hand, this protects the benefits of injured workers. However, these workers may not know that they could have a legitimate third-party claim against the manufacturer or distributor of the table saw.

Table saw manufacturers and distributors are legally responsible for providing safety features that protect the users of their products from injuries due to inadvertent slip ups.

How can a Worker Determine if They Have a Valid Third-Party Claim?

A worker who has been injured in an accident involving a table saw should speak with a qualified lawyer to determine if they have a valid third-party claim. Galfand Berger LLP has obtained numerous significant third-party claim settlements for injured workers, including the following:

• 500,000 recovery for client involved in a power saw accident. The individual lost several fingers. Our lawyers obtained a half-million-dollar settlement because the saw was designed without proper safeguards.
• 400,000 settlement in table saw accident. The client suffered amputation injuries while using a table saw that lacked proper safeguards.

In many cases, manufacturers are automatically held responsible for the damages arising from injuries that are proven to be caused by defective products. However, proving that a product is defective requires the skill and experience of a lawyer.

Philadelphia Products Liability Lawyers at Galfand Berger LLP Advocate for Clients Injured by Defective and Dangerous Table Saws

If you have been injured by a table saw at work, do not assume that the injury is your fault. If the saw could have been designed to prevent your injury, you may have a valid third-party claim against the manufacturer or distributor. Our Philadelphia products liability lawyers at Galfand Berger LLP stand up for the rights of injured consumers and workers. Call us at 800-222-USWA (8792) or contact us online for a free consultation. We have offices located in Philadelphia, Bethlehem, Lancaster, and Reading, Pennsylvania, and we serve clients throughout New Jersey and Pennsylvania, including Allentown and Harrisburg.