A wet candle trimer for Huter grass does not start. Diagnosis of the candle channel

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

  • After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
  • When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
  • At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
  • He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

  • The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
  • Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
  • Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
  • If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate can form on a gas tank day, which is due to which the tasks with the operation of the device appear.
  • Excessive swing of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
  • Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
  • trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
  • Knives are removed from the car. some models will not work under this condition.
  • Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
  • From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

The first is a candle

First of all, you need to unscrew the candle. If it is wet, then the ignition system is faulty. Try wipe the candle, put it in the cap, attach it to the engine, pull the starter. There is a spark? If not, then you need to change the candle.

Replacing the candle did not help? Then you need to watch magneto, cable, ignition coil. The cable is nicknamed, the coil is checked for resistance (multimeter in the resistance measurement mode of 200 Ohms, one contact for the mass, the other to the reel exit should show from 0.4 to 2 ohms).

Sometimes magnets are polluted on the flywheel, or the key is lung, and the ignition moment flies up. Chinese shit throws various surprises, but for the most part everything can be identified visually.

candle, grass, does, start, diagnosis, channel

Be sure to pay attention to the coat of candles. If it is black, the candle is smoked, then the mixture is rich, or you mixed the fuel incorrectly. If the plaque is white, then the mixture is poor, and the engine could already die from the temperature

Ideally, the color should be brick, bright, without much raid

If the plaque is white, then the mixture is poor, and the engine could already die from the temperature. Ideally, the color should be brick, bright, without much raid.

Again, if the black candle is dead, you should not immediately sin on the carburetor and ignition. Plunge the new, see what plaque will be. Maybe just a candle was poor.quality.

Why is a trimmer not starting for grass (gasoline)?

Why is a trimmer not starting for grass (gasoline)?

Because he worked his. Why, this question may be as many answers. Poor fuel is far from an argument. Maybe a person does not know how to use it, so it starts not correctly. The fuel does not come, the candle is pierced, the wires are pierced, it does not turn on, does not know how to use it, the trimmer for the grass burned/broken, but there are still any other reasons can be. There are still such hooks.

The reasons why the gasoline trimmer for grass does not start can be several.

If the trimmer for the grass does not start or immediately stalls after the launch, then the problem may be in the fuel tank (namely as fuel), in the candle and the ultimate channel, in the air or fuel filter, in the saapon or the exhaust channel.

one). Be sure to check for the grass before starting a trimmer for grass, and most importantly and the quality of the fuel mixture.

2). A trimmer for grass may not start or stall with a flooded candle. It will need to be twisted and wiped.

Dry the channel candle for at least 3040 minutes. Otherwise, a new candle can also burst.

3). If a trimmer for grass starts without an air filter, then it is better to change the old filter for a new.

four). A trimmer for grass may not be started if the fuel filter is polluted.

Trimming Candle Wicks ASMR

5). Also, a trimmer for grass may be started due.

Also, the reason may be in the flow of dirt into the exhaust channel or clogging the muffle grid.

A gasoline trimmer for grass may stop starting for several reasons at the same time.

Firstly: try to clean the carburetor-its pollution leads to a breakdown of a gas station.

Secondly: vacuum may form in the barrel. If so, try to make a small click in the barrel lid.

Thirdly: roll the correct settings of the trimmer for the grass.

There are several reasons, as a result of which the trimmer for the grass will not start. I will list the main:

  • Poor fuel. For each model of a trimmer for grass you need gasoline with a specific octane number. Roll up with the operating instructions and make sure that you fill in the required.
  • flooded candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
  • The fuel mixture does not enter the carburetor. Skip it a little.
  • The ignition coil failed.
  • The muffler is clogged. You need to free it from the haze. To do this, carefully disassemble and clean (can be burned on a gas burner).

Typically, the trimmer for the grass did not start after winter and we used to carry almost every spring a trimmer for grass to the workshop, where we were repaired. But, once, a knowledgeable person advised us in.the first, never leave gasoline in trimmer for the winter, because old gasoline may be the reason that the trimmer for the grass will not start, and he also said that the trimmer for the grass for the grass is necessary for the carburetor.fuel mixture. After we began to comply with these rules, our problems with the trimmer disappeared.

First of all, you can see the candle. If necessary, replace it, making sure that the candle is not broken and gives a normal spark. The next problem will be hidden in the fuel system. As mentioned above, check the tightness, then check the fuel filter, if necessary, change. Clean the carburetor, watch the effect. It will be necessary to delve into the ignition system, configure. To check the fuel system, you can pour several grams directly into the cylinder through the candles of the candle, screw the candle and try to start. At least a trimmer for the grass should make the sounds of a running engine within 1-2 seconds and a little smoke should fly out of the silencer.

This is interesting: how to reduce fuel consumption

If you do not start a trimmer for grass at all or immediately stalls after the start of the start, then you first need to look for the reason in the main nodes and units, for this you need to carry out the test in the following sequence, so this sequence: this sequence: this sequence: this sequence:

In these nodes, the whole problem may be consistent.

complex reasons for the refusal of the lawn mower

If the step-by-step algorithm for searching for a malfunction has not given a result, and your braid for grass still does not start or stalls, it is worth examining the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable operation of the tool. Three main problems can be distinguished here:

  • Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a powerful stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
  • Wear of the carburetor laying. Output. replacing the failed laying;
  • Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it with the right. Follow the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, then some part of the carburetor is faulty. Will have to find it and replace it with a new.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips, scratches or bully are found, on the piston or cylinder they should be replaced. Piston rings are subject to mandatory verification. A small rally piston when swaying the connecting rod indicates that the time has come to change the rings. This procedure is best entrusted to the specialists of the service center.

The lawn mower is not started: the reasons and methods of elimination

Diagnosis of the reasons why the lawn mower is not started. A quick return to the life of Chinese and domestic motorcycles with a two.stroke internal combustion engine.

It happens that a two.stroke motor does not even show flashes in the cylinder, but it happens. grabs, and then stalls. Do not be sad, this Chinese consumer goods can be repaired directly on the knee using a minimum of tools.

Before starting diagnostics, you need to make sure that the engine rotates with a slight resistance. If there is no compression in it, then the further is useless, and you need to change the piston (this is also nothing complicated, everything is as a designer).

The lawn mower is not started: the reasons and methods of elimination

Diagnosis of the reasons why the lawn mower is not started. A quick return to the life of Chinese and domestic motorcycles with a two.stroke internal combustion engine.

It happens that a two.stroke motor does not even show flashes in the cylinder, but it happens. grabs, and then stalls. Do not be sad, this Chinese consumer goods can be repaired directly on the knee using a minimum of tools.

Before starting diagnostics, you need to make sure that the engine rotates with a slight resistance. If there is no compression in it, then the further is useless, and you need to change the piston (this is also nothing complicated, everything is as a designer).

Not starting on a cold trimmer for grass. we eliminate the cause

The trimmer for the grass does not start on the cold. The reason is an air leak that does not allow fuel to download. The gasoline trimmer does not start for grass still does not start, Cadet CC 98 b video trimmer for grass. In the camera.

The second reason why the garden tool does not work is the fuel ended. On Elinech T750, a fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and pour gasoline there (the most optimal version of the AI-92, it is inexpensive and does not clog the carburetor as AI-76). Do not forget to add special oil for engines to the tank, 50 grams on the gas tank is enough, without it the motor will begin to “sneeze” and quickly become unusable. After cover the tank with a cap, wipe the surface of a trimmer for grass with a dry rag and our hands. A trimmer for Hitachi grass is not started. Repair, tool, regardless of their small dimensions. We also make the above manipulations to include a garden tool.

The owner of the summer cottage can not do without a lawn mower or. But in the process of its operation, situations may arise when this unit for some reason stops starting up. And there can be many reasons for this. Let’s find out why the gasoline trimmer for grass does not start.

Why is a trimmer not starting for grass. the reasons

To determine why the gasoline trimmer for grass is poorly started or stalls constantly, it is necessary to sequentially check the operation of all the main units of the unit

It is especially important to do this after a long.term storage of a lawn mower. So, the main reasons for such a trimmer’s behavior for the grass are as follows:

  • The culprit that the lawn mower is not started, there may be a poor-quality oil-Benzine fuel mixture. It must be prepared strictly according to the instructions. The savings here are not at all appropriate, since it can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, as excess gasoline will lose their qualities over time.
  • You should know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they are filled with cheap gasoline with a small octane number. Therefore, for such units, it is necessary to use only high.quality high.octane fuel.
  • If the trimmer for the grass stalls immediately during the start, then perhaps he has a candle flooded. In this case, it is necessary to twist it and dry it well for half an hour. Then drain the excess fuel that is in the chamber, clean the candle from the carbon fiber, put it in place and try to start the lawn mower.
  • If your new gasoline trimmer for grass does not start, there may be a lack of a spark. And this happens because the nest, where the candle is located, is dry and fuel does not light up. Should be slightly moisturized with a few drops of gasoline threaded connection of the candle.
  • A gasoline trimmer for grass can stall due to clogging of air or fuel filters. It is best to replace such elements with new.
  • The graduation canal and sapun can also clog. Cleaning these elements of the trimmer for the grass, it will be possible to start the unit without any problems.
  • Another reason why the gasoline trimmer does not start for grass, even when there is a spark, there may be a clogging of a carburetor. To clean the channels and nozzles, it is necessary to blow them with compressed air using a compressor. You can use to clean the carburetor and special washing.
  • If the gaskets of the carburetor are worn out, you need to change them. And in case of violation of the tightness of this device, you will have to determine the faulty part of the carburetor and replace it.
  • A trimmer for grass may not be launched due to wear of the piston group. However, it is better to change such parts of the lawn mower in the service center.

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

In the near future, the gasoline trimmer for the grass got the status of the 1st of the main tools in the arsenal of summer residents. And this is logical, because a motorized braid for grass allows you to quickly put a personal plot in order. But from time to time it happens that a trimmer for grass does not start on a hot and even cool. In such situations, it is necessary without the help of others to establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The prerequisites, which more often lead to such troubles, will be considered further.

Problems with rotation of the cutting canvas

Trimmer’s traction malfunction for grass

On all trimmers of gasoline, a centrifugal clutch is installed, the meaning of which is that the pads, when the speed is added, begin to travel and cling to the cup. The easiest way to check the clutch is to unscrew the bar from the motor, usually 4 bolts. If the pads are pulled, the clutch must be replaced, a metal rattle is heard. If your trimmer provides for a clutch and there is a constant rotation of the fishing line, then the spring is stretched.

Falf in the drive shaft and rod

The main thing to look is: slots on the shaft, connecting the gearbox and clutch cup. Also very often users do not properly insert the rods into the connection, on trimmers with collapsible rods. Be sure to check the integrity of the shaft. If the vibration is present, then plastic bushings are broken. Vibration is very harmful to the vascular apparatus. In order to avoid the melting of the bushings, they must be lubricated and allowed to relax to the mitch.

Ways to eliminate breakdowns

It is no secret that the best and most effective way of repairing is a prevention of possible malfunctions. As already noted, one of the key points is how correctly the gasoline-oil mixture is prepared. Its components should be gasoline at least AI-92 and high-quality motor oil. The proportions, taking into account the mixture, are indicated in the manual of the manufacturer, which is included in the supply of any gasoline trimmer for grass. As a rule, oil to gasoline is added using an ordinary medical syringe. In a similar way it is easiest to observe the appropriate proportions.

Quite often, when problems with the launch of motorcycles arise, the owners of the tool try to carry out repairs with their own hands. In the presence of the necessary knowledge and skills, this approach will significantly reduce operational expenses. First of all, it is worth checking the fuel system and, in particular, the filtering element. If clogging is detected, the filter will be easiest to replace with a new. If an air filter has become source of problems, then you can get out of a difficult situation even in the process of work with minor time costs. The following actions will need to be performed:

  • remove the filter element;
  • Directly in working conditions, you can rinse the filter used by gasoline;
  • When operating, braids for grass or at a summer cottage for cleaning use water and simple detergents;
  • After washing, the part is carefully rinsed and dried;
  • A completely dry filter should be lubricated with engine oil;
  • excess lubricants are removed by compressing the filter element with the hands;
  • The cleaned part is put in place and the plastic cover is attached with screws.

Read which side to put a disk on a trimmer for grass

If the described actions did not provide a positive result, then the next step will be the clearance adjustment using the corresponding carburetor screw. Many publications and videos posted in the open spaces of the World Wide Web are devoted to this topic. When trying to solve the problems under consideration, you can take several steps.

  • The trimmer for the grass is placed on the side so that the “air” is from above. This will allow the fuel mixture to enter the lower part of the carburetor. Often, attempts to launch the internal combustion engine are successful if you pre.dismantle the mentioned part and literally send a couple of drops of gasoline directly to the carburetor itself.
  • If, after all the described actions, the braid could not be brought into working condition, then the candle and, in particular, the presence of a spark should be paid attention to. In parallel, all fuel from the combustion chamber is completely removed.
  • Often, the owners of the benzos are in situations where the fuel and air filters are clean, the candles are good, the fuel mixture is fresh and high.quality, but the internal combustion engine does not show signs of life. In such cases, experienced experts recommend using universal and proven many years of practice by launching. It is necessary to transfer the air damper to a closed position and pull the starter handle once. After the damper, the engine is opened and the engine is launched 2-3 times. In the vast majority of cases, the result is a positive.

Problems may arise with the starter itself. Often there is a cliff of the cable and a breakdown of the handle. You can cope with such troubles yourself. In other cases, as a rule, the starter is replaced. It is worth noting that the Danish device can be purchased and installed with your own hands.

The light of the ignition during the launch of the ICE of the Trimmer for the grass can be filled with fuel. Even with a high.quality mixture and the presence of a good spark, it is unlikely that you can get a device. The most effective exit will be to extract a candle and dry it. In parallel, you can check this spare part for performance, when identifying malfunctions, replace it. This procedure includes a number of simple steps, namely:

  • drown out the device and wait for complete cooling of the power unit;
  • turn off the wire;
  • extract the candle itself;
  • examine the dismantled part;
  • make sure the presence of a gap (0.6 mm);
  • screw a new, working candle and tighten it.

In practice, many repair work related to the fact that the braid for the grass has stopped starting and which sooner or later has to face the operation of a household lawn mower, it is quite possible to cope on its own. But with serious malfunctions, it will be most rational to contact a specialized service. However, the key factor in such cases will be the ratio of the cost of repair and the price of a new trimmer for the grass.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the sapun. The main task of the designated component is the leveling of pressure in the fuel tank. In the case of contamination of the node, a vacuum appears here, which greatly complicates the supply of fuel. Removing a malfunction allows the cleaning of the cabin using an ordinary sewing needle.

The measured functioning of a trimmer for grass may be impaired as a result of laying dirt in the final channel or the formation of a blockage on a muffler grid. Such a disorder in most cases appears during the operation of the older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a multifunctional state, it is worth observing several ordinary rules:

  • Carry out timely, constant technical inspection of the main mechanical nodes of the device.
  • To refuel a trimmer for grass only with the latest fuel, the quality and origin of which is not caused by fluctuations.
  • Inspect after each use of the tool, whether oxides and soils have formed on the surface of parts of the ignition system.
  • Avoid the strong load of the trimmer for grass during work.

So that the unit remains in a working state, you need to correctly prepare it for storage in the winter period. First you should disassemble the tool one hundred percent, then perform washing and cleaning the components of the parts. It is also fundamentally to look around multifunctional blocks for damage, with the need to eliminate the deformation of parts, various distortions, gusts of materials.

Placing a trimmer for storage grass, it is worth filling the gearbox with a sufficient amount of oil. Then you need to clean the air filter, partly disassemble, blow and wash the unit engine. Having dried all the mechanisms, lubricate moving elements. To carry out the processing of the piston system with oils, you need to extract the spark plug for previously. The lawn mower will not start or start, but stalls. What is the reason? If there is no spark. Then it is necessary to move the piston to the extreme position, then pour an insignificant amount of oil into the candle hole and make a scroll of the crankshaft. If the gasoline trimmer for grass in the offseason is not planned to be stored in the house, it is recommended to tightly wrap the unit engine with an oiled rag. This will allow to avoid the development of corrosion on the surface of the fundamental nodes of the mechanism.

The GAMPION BASS GAMPION NOT BECOME Video Video. Why is a trimmer not starting for grass gasoline? Reasons and them. Why the lawn mower or the lawn mower is not started. Prerequisites

A large assortment of gas.tools and components at affordable prices

The assortment of the Kosi Spit for Grass store has a huge selection of specialized products designed to perform work or support important functions of working tools. So, depending on the requests of the buyer, the online catalog offers to choose:

  • Tools:
      Modern lawn mowers of grades GoodLuck, Baikal, Carpathians and other manufacturers;
  • gasoline saws with the selection of power and sawing parameters.
  • Spare parts:
      professional spare parts for the chainsaw of the Chinese release and the CIS countries;
  • high.quality spare parts for benzos;
  • Spare parts for electric saw and other assortment.
  • Components:
      accessories for gasoline cos;
  • original candles;
  • guide tire for a chainsaw of the required length;
  • knives for benzos;
  • files for the chain;
  • Lubrication for motorcycle and oil for nonsense of the desired consistency, depending on the nodes of use.

If necessary, a benzo.tool to buy online, each spare part is equipped with a link to the consumer basket, which simplifies the order process a lot. The manager’s phones that are able to answer questions are also available, to tell what spare parts are available now, how quickly the collection and delivery to the buyer are performed, and also help to choose the necessary elements and order them in the right amount. “Spit for grass” is a modern online store where you can buy spare parts for a chainsaw or lawn mower at an affordable cost.

floods the candle on a gas station

Probably garden tools are useful and effective, but there are times when the technique is abandoned to work. Among them, both a trimmer for grass, which have an option to dig a small clearing and large lawns, hit.

candle, grass, does, start, diagnosis, channel

There are various prerequisites why the gasoline trimmer for the grass does not start:

  • The most common breakdown occasion lies in the wrong choice of fuel. Often very economical users of the device pour something incomprehensible into the tank, but not fuel with an ordinary octane number. The bad fuel, which was kept in the plastic canister, has a terrifying effect. The device that has lost performance therefore sets off to the full bulkhead of the mechanism.

floods the candle on a gas station

Probably garden tools are useful and effective, but there are times when the technique is abandoned to work. Among them, both a trimmer for grass, which have an option to dig a small clearing and large lawns, hit.

There are various prerequisites why the gasoline trimmer for the grass does not start:

  • The most common breakdown occasion lies in the wrong choice of fuel. Often very economical users of the device pour something incomprehensible into the tank, but not fuel with an ordinary octane number. The bad fuel, which was kept in the plastic canister, has a terrifying effect. The device that has lost performance therefore sets off to the full bulkhead of the mechanism.

How to change the piston on the Stihl 180 chainsaw

If you want to replace the old piston and the installation of the latest, you should know how true this is and observe a certain method of action. You also need to have a small slotted screwdriver, a special combined STIHL key, a power screwdriver, a hammer, a groove made of soft material, a compressor and a stop for a stihl piston.

Starting to work on the substitution of the piston as it is also called the piston group assembly, the chainsaw must be cleaned with maximum quality. Further, the work is carried out according to the subsequent method:

  • The upper cover is removed from the saw and the spark plug is turned.
  • The side cover is removed.
  • With the help of a power screwdriver, a stopper is removed from the chainsaw shock absorbers, after which its handle is disconnected from the case.
  • Next, you need to remove the driven star and starter.
  • In the candle hole, install the piston stopper and spin the tank mount nut and clutch.
  • Remove the flywheel, clutch and mechanism of the worm drive of the oil pump, which is placed behind the clutch.
  • Spin two screws of mounting a carburetor and air filter. Remove the filter, engine control lever and stihl carburetor.
  • Remove the ignition coil and muffler.

On the removed engine, the pallet is untwisted and removed, after which the piston assembly with the crankshaft is removed from the motor.

As needed, the replacement of the old piston and the installation of the latest, you should know how true this is and observe a certain method of action. You also need to have a small slotted screwdriver, a special combined STIHL key, a power screwdriver, a hammer, a groove made of soft material, a compressor and a stop for a stihl piston.

When these operations are carried out, you need to additionally clean the saw from the mud, then turn it over the bottom up and turn out the four screws for fastening the motor to the chainsaw body. Having twisted the screws, the engine is separated from the body and is cleaned again.

If such operations are carried out, you need to additionally clean the saw from the dirt, then turn it over the bottom up and turn out the four screws for fastening the motor to the chainsaw body. Having unscrewed the screws, the engine is separated from the body and is cleaned one more time.

Maintenance and prevention of launch problems

So that the tool serves longer and does not create problems, keep it clean and regularly maintain.

Do not store the refueling lawn mower: leaving it for more than 2 weeks, and even more so for the winter, drain the remaining fuel from the tank, then start the motor and let it work until it stalls yourself. Leaving the tool for the winter in the barn, wrap the motor and knives with an oiled rag.

For lubrication of a 2.stroke motor before storage, unscrew the candle and raise the piston with the starter to the very top. Drip a little motor oil from the syringe and use the starter several times cranks.

In the spring, before the first use after downtime, it is advisable to check the candle and filters, disassemble and rinse the carburetor, even if there are no problems with the launch.

Conclusions and useful videos

For clarity, we offer a video with the analysis of common problems:

To check the carburetor or if you decide to change the oil seal yourself, it will come in handy

Dismantling and cleaning the carburetor is described in sufficient detail here:

If your lawn mower does not start, do not rush to look for a master to repair it. It is possible to independently find and eliminate the cause not only much cheaper, but also faster and easier.

Most trimmers are arranged almost identical, the structure of small details may differ and, of course, the quality of their performance. Use and store your tool carefully, do not spare money for fuels and lubricants and time for minimal service, and the trimmer for the grass will become a trouble-free assistant for many years.

Did you have to face a situation where the lawn mower stopped starting? How did you fix the situation? Share your opinion and experience in the Комментарии и мнения владельцев below!

Candle care. Trim your wick 1/2” before every burn | Tevin Vincent candle company