Chainsaw Transfuses And Doesn't Start

Popular materials

Today’s:

Stihl 180 chainsaw repair will not start. Stihl 180 Chainsaw Doesn’t Start

"MASTER PLUS" repair of various complexity in the city of Serov

Chainsaw Stihl 180 Fuel enters a spark on a candle; does not start; fills a candle

Record 9 comments

I had the same problem, the brand-new saw after the 2nd refueling did not start, which I just did not find in the tips, turn off the jam, look at the piston, but there is no need to do this if you feel that there are compression, the starter cable is stretched with effort. And our client was left to the pointlessness simply, flooded the candle and for inexperience. We merge all gasoline from the barrel. We unscrew the candle, check the spark, then we need to drain the remaining gasoline from the cylinder, for this purpose we turn the cylinder down gently pull the trigger cable, draining excess 10 times approximately. After that, I put in this section the same position saw for min 5 for ventilation and drying, we twist the candle. We fill the tank with gasoline and oil in the indicated proportions. I put the lever in a cool start pulling twice smoothly with the 3rd jump, started up from the third jerk. And I was going to take it to the service.

The same problem, a brand new saw, at the second gas station finished wind up. Checked, overfilling the carburetor, a candle in gasoline, after drying, a spark appeared. After purging the cylinder, as described in the annotation, I tried to start it. When the “Cold start” flap position is one flash, I move the flap to the start position. it will not start. He unscrewed the candle. again in gasoline. He blew the starter a hundred times, the problem is the same. And then, having come to your website, having read Oleg’s advice (regarding blowing by the starter in the inverted position of the saw) he tried, gr 10 gasoline spilled from the cylinder and carburetor. Then, attaching the candle (without screwing it) to the tip, set the flap to the starting position, still blew. Gathered, refueled. wound up. So thanks to Oleg for good advice!

The Stihl 180 chainsaw starts and stalls.

DOES NOT START STihl 170/180. CAUSES.

The main REASONS DO NOT START THE ENGINE. NO SPARK ON THE IGNITION CANDLE (Change the CANDLE.

Thanks for the advice.

Oleg, thank you very much what remains to make our client excellent simply! it happened badly and at some point everything started I followed your advice. The problem dared, Well-KO funds for the newest candle and air. filter, but I think in the future it may be needed. Thanks in addition. Honored readers. always start with a simple in most cases, the catch is small. Good luck to everyone in repair!

Thanks to Oleg for good advice. Such advice should be prescribed in the instructions. The brand new saw did not start for the third time, there are sparks, alas, it throws a candle. I did what remains to be done to our client because Oleg wrote, started up from the first jerk.

Stihl 180 Chainsaw carburetor malfunctions. Why the Stihl 180 carburetor overfills and a few characteristic malfunctions

After we examined the carburetor device, determining the reason why the fuel enters the combustion chamber in a larger volume is not difficult. This happens due to wear on the gasket between the compensator cover and the carburetor body. You may ask how this can affect?

The answer is simple, shrinking, the gasket releases the diaphragm located on top of it a fraction of a millimeter down. She, in turn, will put more pressure on the rocker arm of the needle valve, it will open more than expected and the fuel will flow in excess (begin to overfill).

Another reason is the extension of the diaphragm itself, this occurs as a result of natural wear. It is impossible to prevent this process, but it is possible to solve the problem by periodically changing all gaskets, carburetor diaphragms, and the fuel pump. There is a repair kit for this.

Stihl 250 chainsaw Starts up and Stalls Reasons why a chainsaw starts up and stalls A long time ago a chainsaw has not been a luxury, but a necessary tool for those people who have a summer cottage or home ownership. However, just as it doesn’t matter what other technique, this tool tends to fail, regardless of a simple device. The systematization of the main defects contains Poor Stihl chainsaw Starts Reasons What to do if the chainsaw does not start Good day, dear readers and subscribers of my blog! At one inopportune moment. You can easily find that your chainsaw will not start. But do not rush to immediately hand over the instrument for repair, you can easily remove this breakdown yourself. I will tell you what to do, in cases when it won’t start Electric Chain Saw Stihl Video. Electric saws MSE 170 CQ, MSE 190 CQ, MSE 190 C-BQ, MSE 210 C-BQ, MSE 230 C-BQ, MSE 250 C-QPromo-msk.ru Overview of electric saws MSE 170 CQ, MSE 190 CQ, MSE 190 C-BQ, MSE 210 C-BQ, MSE 230 C-BQ, MSE 250. Overview of the Stihl MSE 141C saw. AND WHY SO SUCH A LITTLE COMMENT DEDICATED TO MY OCCASIONAL DISCLAIMER ABOUT TIRE LENGTH 40

Stihl 180 stalls idling. Read the same

The chainsaw may muffle if the fuel filter is clogged.

You will also like the air filter more clogged with dirt, as it is also called dust, which leads to malfunctions at idle. It should be borne in mind that clogging of this filter occurs sometimes, under the influence of which the flow of air into the system is difficult. In the fuel-air consistency, a fraction of gasoline increases, and it comes out too enriched. Under such circumstances, normal operation of the motor is not necessary.

For cleaning, the air filter is removed with special care so as not to dust off the carburetor. Then it is cleaned and painstakingly washed. Detergent is added to the wash water. After drying, the air filter returns to its own skill place in a chainsaw.

For normal operation of the cutting tool, it is recommended to change the fuel and air filters once every couple of months.

Usually, this common rumor is recommended to change the main component of the accounting system of ignition at least once a year. But often the owners of the saws forget about this decision to the rule. In this regard, it makes no sense to be surprised that the apparatus, whose maintenance is fragmented, ultimately poorly "keeps" idle speed.

The chainsaw spark plug must be changed 1 time during the year.

Therefore, it is necessary to find out on the following malfunctions associated with the service of this complex of accounting programs:

Filling a candle with gasoline at the time of launch. To eliminate the problem, unscrew the candle and without even burning, dry it. Through the hole-socket, into which the candle is screwed, excess gasoline is connected from the motor. After a break in Half an hour, the candle is set to the area, the mechanism starts.
Lack of spark due to disgusting contact of the candle tip with the high voltage wire. The connection is checked, in case of violation, the defect is eliminated.
There is no spark due to a malfunction of the electrical ignition unit. If you can be sure of the reliability of the connection of the tip with the high-voltage wire, alas, there is no spark when the starter is turned on, then the cause of the breakdown may be a malfunction of the ignition unit. the myth component is not restored, it is only replaced with a new one.
Incorrect gap between the spark plug electrodes. In various types of candles, this indicator ranges from 0.2 to 0.5 mm. The correct clearance is established by means of a probe of the appropriate thickness. Otherwise, the smallest clearance for this type of candle is not allowed.

Video: Chainsaw Transfuses And Doesn’t Start

Stihl 180 overflows the carburetor. Communities ›Do It Yourself› Blog ›Benzopila Stihl 180. Self-repair

Eight years ago, a saw was bought and worked faithfully. And once again, I took out a chifir-chifir, but it did not start The first thought, I put it in for repair, and then I thought, I can handle the UAZ, I can try it with a saw. I checked the spark, there is a spark. There is gas supply too. He unscrewed the candle, it was filled with gasoline. In short, it turns out, overflows the carburetor. I rummaged through the net, it turns out to be laying in the crab, dubbing, constantly presses on the needle, hence the overflow.
In principle, the most difficult part was to find in the city. A set of carburetor gaskets were bought, two muffler studs, the nuts turned sour, I decided to change for one, a reinforced air filter, a new sample and a gear emphasis, plastic teeth on the saw were already grind off.
Further, simple. We remove the air filter by unscrewing two nuts by 8, they also attract the carburetor, disconnect the fuel hose, remove the rods from the carburetor and snap out the shift control shaft and remove the carburetor.
We remove the cover, look at the gasket, oak, change it and everything is in the reverse order.
With silencer mounting studs, it’s even easier, I ground the nuts on an emery and replaced 🙂
And he put a metal stop.
The saw started up, after repair, and has already been tested in work.
After a year of use, little by little again, it fluttered.
It was necessary not to save and take the original repair kit.

Membrane of the carburetor Stihl 180. Chainsaw Stihl 180. device and adjustment of the carburetor

The stihl ms 180 chainsaws are designed in such a way as to facilitate their operation as little as possible by inexperienced users. To do this, some settings available on the more powerful Stihl models were canceled in the carburetor of the saw. But there is still the opportunity to adjust, and repair, as well as adjusting the carburetor of the Stihl 180 chainsaw with your own hands, is possible.

When to adjust your Stihl 180 carburetor

To begin with, it’s worth deciding why, in general, you may need to adjust and repair the stihl ms 180 carburetor. So, you need to do this in the following cases:

if the chainsaw does not keep idle;
repairs may be required if the saw does not start;
there is a loss of power;
increased fuel consumption;
chainsaw does not develop maximum speed.
stalls at speed.

This list can be continued for a long time, but we have identified the main reasons. Before proceeding with the adjustment, it is necessary to know what are the main parts of the carburetor on the Stihl 180 chainsaw, and who produces it.

Carburetor Stihl 180

So, the stihl ms 180 carburetor is designed and manufactured by a subsidiary of Stihl, called Zama. Original carburetors on their case have a company logo guaranteeing product quality.

Fuel pump

A fuel pump is installed directly in the carburetor body, which operates under the influence of an air pulse from the crankcase of the chainsaw, transmitted through special channels. A diaphragm is installed in the pump, and it is it that is responsible for pumping fuel under the influence of a pulse. A gasket is installed between the diaphragm and the housing, which is responsible for the tightness of the fuel pump.

Distribution chamber

In the distribution chamber, as in the fuel pump, there is also a membrane that opens and regulates the fuel supply by pressing a special rocker, while raising its needle valve.

The chamber cover is the compensator body, which is mounted on the carburetor with four screws; a gasket is installed between the body and the cover, which increases the height of the chamber and is responsible for sealing.

Nozzle

The fuel injector is mounted in the carburetor body in such a way that it is a connecting link between the distribution chamber and the cavity in which the throttle valve is installed. Simultaneously with the fuel, air is supplied to the nozzle and an air mixture is formed. The nozzle has a check valve that blocks the flow of air in the reverse sequence, that is, from the throttle chamber to the distribution chamber.

Throttle damper

A throttle is installed in the carburetor housing and is responsible for increasing the supply of the fuel mixture directly to the engine cylinder. At the moment of pressing the gas, the throttle opens slightly, thereby increasing the channel capacity and fuel from the carburetor cavity, rushes into the cylinder in a larger volume.

The combustion of a larger volume of fuel increases the amount of energy generated, which affects the power and speed of the processes. The damper is mounted on a shaft passing through the entire carburetor body. At the output of the shaft from the housing, a mount for the gas cable is installed, a conical, adjusting screw responsible for idle speed adjustment is located nearby. By tightening the screw, you can slightly adjust the position of the shaft and the shutter installed on it, thereby increasing or decreasing the idle speed by slightly opening or vice versa closing the shutter.

Air damper

The carburetor air damper is installed on the opposite side of the throttle and is responsible for starting a cold engine, its control is carried out by the engine control lever. For a cold start, the air damper is completely closed, for normal operation open.

Carburetor adjustment Stihl 180

The carburetor of the Stihl 180 chainsaw, indiscriminately, can only be adjusted by the number of revolutions at idle. It is impossible to increase or decrease the fuel supply in various modes with the help of special screws. The manufacturer restricts access to adjustments and does not install these screws. How to adjust the carburetor to the correct idle speed is described in great detail in the manufacturer’s instructions.

In the event of certain malfunctions and experience, it is possible to increase or decrease the fuel supply by increasing the clearance when opening the needle valve.

To increase the feed, the rocker of the needle valve in the distribution chamber must be bent up, and to decrease, down. Thus, the stroke of the needle and, accordingly, the throughput of the valve are regulated.

It is not necessary to carry out the adjustment on your own, because it must be done very accurately and, with an error, returning the initial position of the rocker arm is almost impossible.

Why the Stihl 180 carburetor overfills and some characteristic malfunctions

When cleaning the chainsaw with compressed air, in no case should you blow into the fuel pipe, this can lead to an extension of the diaphragm.

Frequent breakdown of a Stihl carburetor and how to avoid it

A common cause of failure of the carburetor on a Stihl chainsaw is sticking of the valve in the nozzle. The cause of sticking is a violation of the storage of the chainsaw, or rather the manufacturer’s instructions Stihl 180 on proper preparation for storage.

As follows from the instructions, before long-term storage, it is necessary to drain the fuel from the tank, then start the saw and burn gas from the carburetor. Failure to comply with this elementary rule entails the following consequences. The forsknui valve, being in direct contact with the fuel, sticks to the body, since gasoline gradually evaporates and only sticky oil remains. The nozzle cannot be replaced, because they are not in the repair kit, you can only try to knock it out and rinse, which is not always possible to do without ruining the nozzle.

Removal and Installation Algorithm

In cases where you need to clean the Stihl 180 carburetor or disassemble it, first you need to remove the assembly from the chainsaw. This must be done in compliance with a certain algorithm of actions:

Attach a protective cover for the chainsaw to the tire.
Remove the top cover of the chainsaw.
Unscrew the two nuts securing the air filter and carburetor.
Remove the air filter housing.
Disconnect wire from engine control lever.
Carefully remove the lever from the seat in the housing, while disconnecting the air damper rod from it.
Pull the carburetor towards you and disconnect the fuel supply as well as the throttle link.

To facilitate dismantling, you can further unwind the rear handle and disconnect the throttle rod from it first, and then only from the carburetor. This may be required, because without any experience disconnecting the thrust from the carburetor is quite problematic and easier to disassemble the handle first.

Install the part in place, following the reverse order of the algorithm.

When removing and installing the control lever of the chainsaw engine, you should be extremely careful, because the seat on the saw body is a weak link in the saw, and very often inexperienced users break it.

Dismantling the Stihl 180 carburetor

In order to blow, change gaskets or a needle valve, the carburetor must be disassembled. To do this, unscrew 4 screws on the cover of the compensator and one on the fuel pump.

Opening the case, you should be extremely careful, because if debris enters the carburetor inside, it will make it impossible to work. The thickness of the channels in it is comparable to the thickness of a thread or even a human hair.

Video for repairing a Stihl 180 carburetor, see below. In it, the master tells in detail about the problems and clearly demonstrates the entire repair process.

Conclusion

In conclusion, I would like to once again note that the Stihl carburetors, which are produced by its subsidiary Zama, are very reliable. With proper operation and storage, they are able to serve the entire time allotted to the chainsaw without repair.

source

Chainsaws chainsaw, doesn, start, transfuses