Cut the laminate with a corner grinder. Circular Saw. Requires inspection

What disk to saw a laminate with a corner grinder

In the process of laying the laminate, there is a need for its trimming, and then the question arises: how to cut a laminate, corner grinder, jigsaw or disk saw (circular)? And which disk for cutting laminate to choose? And here, perhaps, the question of what to saw is the most important. Many newcomers are trying to trim the laminate with a corner grinder, the benefit of special wood wheels for Bulgarians is on sale, but it is wrong, too much turnover, it is very dangerous.

Cutting laminate Circular cutting laminate with circular

No, theoretically, a laminate can be cut with a corner grinder, especially if the corner grinder has a revolution regulator, which happens infrequently. Just adjust to minimum turns and install a wood disk. But most of the Bulgarians, especially inexpensive, such revolution regulators are absent.

I usually cut the laminate with a disc saw, installing the disks according to the laminate, I usually choose the same manufacturer as the saw, in this case, I have a “Bosch” circular. However, you can do others, look at the marking, usually on the disks it is written. “by laminate”. The laminate disk usually differs from the standard tree in smaller teeth, for a “clean” cut.

Disk saw a pilepid pile in laminate

You can also saw with universal wood drives, it is just not very convenient, and the cut will turn out thick and uneven, but for lack of disks in the laminate, and this option will do.

Actually, since the laminate trimming is carried out at the lamellas, which will be located against the wall, followed by covering the cuts with a skirting board, that is, will not be visible. Therefore, about the “purity” of the cut, I, as a rule, do not bother.

And already according to the diameter of the disk. this must be selected for your saw, you can read in the instructions with which disks your saw works.

Laminat cutting with a jigsaw

As for the electric jigsaw, it is also convenient for them to cut a laminate, perhaps this option is even preferable. For a jigsaw, select files with small teeth.

Guillotine for cutting guillotine laminate for laminate cutting

There are also special guillotics for cutting laminate, but if you have a one.time job, then it makes sense to buy an expensive device (about 10 thousand. rubles) is unprofitable.

How to cut a laminate at home without chips

Ламинат можно резать пилками, дисками, резаками и даже ножом. Правильный инструмент значительно ускорит время при укладке. Тем более стоимость его не так велика. И лучше потратить 20-30 долларов на тот же лобзик, чем пилить обычной ножовкой. Хотя кроме лобзика еще есть много вариантов.

Today we consider all the ways. You will learn how to cut a laminate best and from which side. We will also talk about how to saw lamellas correctly and without chips.

Perhaps you already have some kind of tool. Most often it is a simple saw, angular grinder or jigsaw. For them we will choose the right wheels, and good files.

When choosing a tool for cutting a laminate at home, it is important:

  • Its speed and convenience when cutting. Pulling a heavy machine makes no sense;
  • Pure and even cuts without chips and bullying at least garbage. It is clear that all the slices will go under the plinth. But you can lay the laminate not only on the floor. Often chips can spoil the appearance. Or you need to make a joint of tiles with a laminate without a rocking;
  • Whether the tool is useful after laying. We take what will not gather dust in the closet at a reasonable price (if there is nothing to cut);

How to cut a laminate with a jigsaw. the right files solve everything

Most often recommended to saw lamellas with an electrician. In general, a jigsaw is a universal device. The tool is always needed on the farm. And it is not expensive. The cheapest device is easy to find for 20.

It is light and mobile, you will quickly learn to work with it. This is how to cut a laminate is really convenient. Here is the main solid hand (so as not to drive to the sides) and the selection of files. Which side of sawing will we figure out further.

How to cut a laminate with an electrician:

  • It is very important what pieces to cut laminated boards. There are special on sale. for laminate. But if you did not find them in trouble. So that there are no chips on the front side, make markings and cut it on it. And then we just use a file with teeth that are directed down. It is she who provides almost the perfect cut. All chips will be on the bottom of the lamella. But you have only a saw with teeth at home. In this case, we make markings and saw on the back side. That’s the whole secret. Some still use metal files.
  • You need to cut the laminate in another room. There will be a lot of sawdust. By the way, they are scattered differently depending on the file. Cloves up. sawdust up and vice versa. This is that sometimes you need to put on glasses;
  • You need to hold a piece that we cut off. Since at the end of sawing it can tear a piece of coating from above;

A jigsaw can be sawed laminate not only in length and width. You can easily perform curly cutting with rounded corners. For example, make a beautiful drank for a pipe.

Is it possible to cut a laminate with a corner grinder, it is also an angle grinding machine (angular grinder)

If you have a corner grinder, feel free to use it to cut the laminate when laying. She can cut almost everything in the world. This tool is always at hand with a good owner. You can find a new corner grinder for 25 (this is the simplest). It is important to choose the desired disk here. Ordinary abrasive (black) is not suitable, the board will burn and smoke. Drinking a laminate with a corner grinder for a beginner without preparation is more difficult. You need to get used to the tool.

How to cut a laminate with a corner grinder. important nuances:

  • We immediately determine which disk to saw. It is best for cutting to be the same for a tape disk (by ceramics, porcelain tiles). Make markings on the front of the board and immediately cut. It will turn out a very even and clean cut, no chips. It is advisable to hold the sawed part of the board;
  • Corner grinder saws very dusty. If sawdust flies during the cut, then fine dust here is flying. She settles on Lameli herself and throughout the room. Therefore, it is better to cut a laminate to go outside or on the balcony.

Is it worth cutting the laminate with a regular saw

A simple wood saw of course will cut a laminated board, but. She has large teeth. there will be chips and torn areas if you saw it from the front side. You can try to saw the planks of the laminate with a hacksaw for metal. Her teeth are much smaller and thinner. In any case, using a simple saw or hacksaw is a long, tedious and very difficult task.

over, compressed boards are very dug for the tool. The fact that the jigsaw or angular grinder does in a couple of seconds, you need to suffer for 1-2 minutes with a saw. After the cut of several lamellas. hands and all sweaty. And also half the room is not laid. Now imagine that you have sipped crookedly. The novice master does not always manage to cut properly the first time.

Which saw is better to use? If you need the perfect cut without chips, we buy a hacksaw for metal. Its price is 5-10. It is not a fact that one hacksaw is enough to lay a laminate in the whole apartment.

Circular saw/machine or circular

The cheapest circular, meaning a saw, costs from 40. Buying it specifically for a cut of laminate when laying it is pointless. And drag a huge machine into an apartment is also not an option. If you are a happy owner of this tool, you can safely cut a laminate. To do this, use a metal disk. The newcomer will have to learn how to use the circular. This is not safe, even experienced craftsmen sometimes get injuries.

Features of the use of circular saw:

  • Mark and cut on the front side;
  • Reliably fix the workpiece on a flat surface upwards. It is to fix it, and not so that one holds, and the other saws;
  • If you have a circular machine. marking and cut also on the side with a pattern;
  • In the case of using the machine, the laminate board is not fixed. She is neatly conducted to disk. Be sure to use glasses so that large sawdust does not get into the eye.

Special cutter, guillotine for laminate

The home master definitely should not purchase this expensive tool. over, he can cut a laminate along it very badly. For 40-50, which are asked for it, it is better to buy a more expensive electrician. The device consists of the base and a handle with a blade for cutting lamellas.

The principle of its work is quite simple. Put the plank of the laminate on the base and lower the handle down. However, when working with this tool, there are features. Here they are:

  • As already mentioned above, this guillotine does not cut well along;
  • Cuts off very not carefully, the cut piece looks like a stub. Even the sharp blade of the Rezak literally tears laminate;
  • You need to make a lot of effort, and the blade is quickly stupid. Hands are very tired. A thick laminate of more than 8 mm may not cut;
  • Used only to cut the laminate. T.e. In the farm, this device will no longer come in handy. So, for home conditions is not suitable.

Types of tool cutting tools

By virtue of its structure, the laminate is well sawn by wood tool and is extremely simple to process for masters of different levels: from professionals with many years of experience to beginners.

A feature is that the cut of the material is carried out directly at the installation site. At the same time, it is very important to achieve a qualitatively even cut and not spoil the panel.

Turning to specialists with the question of how to cut a laminate quickly and efficiently, you can get various tips. After all, each master has its own criteria for selecting tools, their own characteristics and knowledge of technology, experience and natural ingenuity. For one it is important to work with an easy and mobile tool, for the other, the issue of connecting to a power grid or manual execution is important. However, everyone converges in one opinion: laminate cutting should be performed qualitatively, providing an ideal cut.

The entire laminate cutting tool can be divided into two categories: manual tool and power tool. The advantages of the first category are the versatility of application and affordable price. The use of the instrument of the second group, despite the higher cost and dependence on the connection location to the mains, can significantly accelerate and facilitate the process of installing the coating.

When choosing how to cut a laminate, you can count up to seven tools:

  • hacksaw;
  • electrician;
  • circular saw;
  • corner grinder;
  • special cutting;
  • construction knife;
  • and even an ordinary clerical knife.

The use of any tool from the list given with appropriate experience will allow you to get a high.quality and neat slice. A general or unified recommendation than cutting a laminate at home, which equipment or device does not exist in a particular situation. Each master, on the basis of personal practical experience, knowledge and professional training, has his own preferences and “chips”. It is important to take into account that in any of the selected methods, one should be guided by popular wisdom: “Measure seven times, cut off once”.

Consider briefly the purpose and principles of the work of each type of tool for cutting the laminate.

Hacksaw

Let’s start with the simplest and affordable. manual wood or hacksaw saw. This is a hand tool that is in almost every house. The hacksaw requires the use of physical efforts and can be used when cutting a small amount of material. On a large volume its use is not effective. At the same time, the choice of hacksaw with large teeth can lead to the destruction of the decorative surface of the coating lamellas. To prevent such consequences, it is better to use a hacksaw with small teeth or a hacksaw for metal.

Tip: Before proceeding to the saw, a painting tape should be glued to this place, which will protect from the formation of chips at the site of the cut. At the same time, it is recommended to lay the board with a facial coating up.

The hacksaw is not the main tool for cutting laminate in professionals due to low productivity, large physical costs and the danger of damage to the decorative layer of the panel. But in some cases with small volumes, when it is impractical to use an electrician or corner grinder, a hacksaw may be useful.

A direct alternative to a hacksaw is an electric saber’s saw. Now the market is a large selection of such a tool. However, the electric saw will not add much to amenities and speeds in work. Therefore, in our review we will not dwell on it in detail.

Electric

The electric jigsaw is a convenient, simple and very productive tool. In most cases, it occupies the first place, thanks to the convenience of circulation, accessibility in operation and efficiency of use. Therefore, when searching for solutions to the problem, than to cut a laminate at home, many of the users opt for it.

To use an electrician does not need special training or long.term skill, everyone can successfully cope with it. The result will be of high quality, the cut will be even and perfectly smooth, given that the tool works at high speeds. The main thing in its use is the correct selection of a laminate file.

Typically, a set with a jigsaw includes several paintings designed for processing a tree or laminate. If you do not have them, you should take care of the purchase in advance. Lamite on an electric laminate has a special shape and a small step of the teeth. Look for the appropriate marking on the packaging. The use of a wrong file will lead to the appearance of chips on the edges of the cut. Therefore, it is better to cut the panels with a special file for a laminate jig. If you could not find one, you can use the canvas for the metal, but the productivity of the work will be slightly reduced.

Important! Marking is performed from the wrong side of the panel. For cutting a jigsaw, it is necessary to lay the workpiece on a flat clean surface with a decorative side down. So the teeth of the files less damage the panel during the cut.

An important advantage of an electrician over other types of tools is the ability to make not only direct cuts, but also curved. This is very relevant if necessary to put a laminate floor in the places of passage of pipes and communications. Under them, the jigsaw will easily cut through the grooves and suckers.

A circular saw

The circular saw allows you to get a more even cut of laminate than an electrician, and at the same time much faster. However, working with such a tool requires great attention and is much more dangerous. Therefore, it is recommended to use the circular saw only to those who have skills and experience with a similar tool, or familiarized themselves with the order of work by watching the video.

Features of the laminate cutting process

Starting to lay a laminated floor, you need to know not only how to cut a laminate at home, but also how to use tools correctly. Among the main determining moments regarding the features of working with laminate, the following can be noted:

  • Large efforts should not be used when cutting laminate;
  • With a poorly cut, the board should be laid by the damaged side under the baseboard;
  • To obtain the perfect cut, the workpiece should be placed downward when working with a corner grinding and a circular saw or upside down when an electrician;
  • Before the rez, check the calculations several times in order to prevent damage to the materials;
  • Figure cuts should be performed using a template for measuring bends, gluing construction tape into the place of cutting.

Recommendations for cutting without chips

Firstly, as mentioned above, you should use a file for an electrician with a direct cut.

Secondly, in order to more qualitatively control the cutting process, the marginal fishing line for a trimmer is justified on both sides laminated wood-bearing plate and check the accuracy of processing from above and below.

Well, thirdly, make constant breaks in work to cool the cutting equipment.

Read also: tiles manual how to use video

Sometimes, the solution in this issue can be a simple cutting of the lemmian layer of the material using a mounting knife, and the subsequent work with a jigsaw will no longer cause large defects in the form of chips. However, this work requires a certain experience and accuracy from the contractor.

If you liked the material, I will be grateful if you recommend it to friends or leave a useful comment.

In the process of laying the flooring, namely the laminate, it is important not only to be able to correctly connect the panels together. It is also necessary to correctly measure the size of the panels in accordance with the area of ​​the room, and also do not violate the traditional masonry in a checkerboard pattern. In such a situation, the question reasonably arises. how to cut the panel measured in size? Let’s try to figure out the situation.

How can you cut a laminate at home

Depending on the thickness and material of the laminate board, you can use several options for cutting tools that are probably available in a home workshop. The idea to cut a laminate using only the strength of the hands is good if you need to repair or replace one or two lamellas. In other cases, it will be extremely difficult to do without power tools.

The traditional set, with which you can accurately and neatly cut the laminate, looks as follows:

  • Manual hacksaw with a canvas for cutting metal;
  • Circular saw in manual or desktop design;
  • Guillotine cutter in a floor or desktop version;
  • Construction grinder for cutting reinforcement or corner grinder;
  • Renovator or vibration cut;
  • Electric jigsaw;
  • A special knife for cutting wood.fiber slab.
laminate, corner, grinder, circular, requires

Important! Not all of the listed materials and tools are equally good for cutting a stove from pressed chips and wood fiber. In addition, the quality of the cut depends on the experience and the ability to handle the tool.

The easiest option is to make a special cutting knife for cutting laminate. The design of the blade differs from the stationery and ordinary knife by the presence of 2-3 teeth on the front edge. Such a cutter is usually made from an old wood saw, the cutting edge is pulled from the opposite sides. In order to cut the laminate, it is necessary to attach a carpenter, apply a fishing line for a cutter to a cutter to a lamella. After that, the film is cut out with an ordinary knife, and then the square is changed to the locksmith ruler, and the rest of the laminate is cut through the laminate with a cutter.

Vinyl cut knife

The fishing line for the trimmer cut is not too smooth, but at the same time there are no chips and paper fringe on the edges.

Cutting the laminate with guillotine

The tool is largely similar to a cutting knife. The design of the tool is presented in the photo below.

Universal tool for any type of laminate

The cutting part is fixed on the steel frame. a stand, and the cutter itself can rotate around the hinge at the end of the device. The fishing line for the trimmer of the cut is flat and flat, but the material, especially on the edges, can be deformed due to a large pressure on the surface of the laminate. In order to cut it with guillotine, it is not necessary for special preparation. The cutter is usually used for cutting vinyl slabs and lamellas.

Cutting laminate corner grind

This is one of the most successful tools used for cutting and cutting building materials. High speed rotation of the cutting circle provide the highest quality of laminate cutting. In order to cut off the part of the laminate panel, it is enough to lay the material on the edge of the table or workbench, fix it, and with a slight effort to smoothly perform the incision along the marking line. Thanks to huge power, you can cut the laminate any thickness.

With one hand you can cut only if there is a special support heel

Note! Corner grinders cannot be cut on the basis of PVC. In this case, the fishing line for the trimmer of the cut is uneven, the plastic is paid and follows from the contact zone.

You can cut a soft wood panel with almost any cutting circle. It is best for cutting a laminate with a corner grinding laminate is suitable for a disc with a diameter of 110-125 mm and a thickness of 0.8-1.5 mm. Various kinds of diamond and nitride-based circles on a metallic basis cope with the task a little worse.

In order to cut a laminate, a small machine with a capacity of 300-500 watts is enough. In the presence of a certain experience, the incision can be performed even with one hand.

Cutting the laminate with a jigsaw

The popularity of the electrician is very great, it is used to cut out all kinds of lumber, plastic and even thin.leaved metal. There are several options for hacksaw paintings for materials for materials of various density and hardness. Usually this is a short titanium blade with sharp teeth, for metal tooth metal is 1-1.5 mm, for soft wood and plastic, the size of the cutting edge increases by 2 times.

Electricity is a convenient tool if you need to cut the cutting very quickly, as they say, “on the fly”. But a seam or a fishing line for a cutter of cut after using a jigsaw is not the most even. over, if you use a canvas with teeth of high altitudes and cut at low speed, then the cutting edge is strongly “shaggy” of laminate material.

Be sure to use guide devices

Awesome idea with Angle Grinder! And so it was possible

Therefore, in order to cut the laminate with a jigsaw without chips, you must adhere to the following rules:

  • You can cut the laminate only in an inverted state, the front part on the table or the supporting surface of the workbench;
  • If the back side is very soft, then the top line is best glued to the usual tape. The tape does not interfere with the movement of the teeth, while maintaining the edges of the incision whole;
  • Cutting speed is selected individually. Typically, for soft materials, high speeds are chosen when minimal supply of the canvas.

Another condition is that you can’t cut the laminate with an electrician on weight, there must be a hard support, both for lamellas and for the sole of the jigsaw. In addition, if the width of the laminate is more than 15 cm, then it is necessary to use the guide bar, which is attached to the tool case and provides smooth and uniform movement during the cutting process.

How can you cut a laminate at home

Depending on the thickness and material of the laminate board, you can use several options for cutting tools that are probably available in a home workshop. The idea to cut a laminate using only the strength of the hands is good if you need to repair or replace one or two lamellas. In other cases, it will be extremely difficult to do without power tools.

The traditional set, with which you can accurately and neatly cut the laminate, looks as follows:

  • Manual hacksaw with a canvas for cutting metal;
  • Circular saw in manual or desktop design;
  • Guillotine cutter in a floor or desktop version;
  • Construction grinder for cutting reinforcement or corner grinder;
  • Renovator or vibration cut;
  • Electric jigsaw;
  • A special knife for cutting wood.fiber slab.

Important! Not all of the listed materials and tools are equally good for cutting a stove from pressed chips and wood fiber. In addition, the quality of the cut depends on the experience and the ability to handle the tool.

The easiest option is to make a special cutting knife for cutting laminate. The design of the blade differs from the stationery and ordinary knife by the presence of 2-3 teeth on the front edge. Such a cutter is usually made from an old wood saw, the cutting edge is pulled from the opposite sides. In order to cut the laminate, it is necessary to attach a carpenter, apply a fishing line for a cutter to a cutter to a lamella. After that, the film is cut out with an ordinary knife, and then the square is changed to the locksmith ruler, and the rest of the laminate is cut through the laminate with a cutter.

Vinyl cut knife

The fishing line for the trimmer cut is not too smooth, but at the same time there are no chips and paper fringe on the edges.

Cutting the laminate with guillotine

The tool is largely similar to a cutting knife. The design of the tool is presented in the photo below.

Universal tool for any type of laminate

The cutting part is fixed on the steel frame. a stand, and the cutter itself can rotate around the hinge at the end of the device. The fishing line for the trimmer of the cut is flat and flat, but the material, especially on the edges, can be deformed due to a large pressure on the surface of the laminate. In order to cut it with guillotine, it is not necessary for special preparation. The cutter is usually used for cutting vinyl slabs and lamellas.

Cutting laminate corner grind

This is one of the most successful tools used for cutting and cutting building materials. High speed rotation of the cutting circle provide the highest quality of laminate cutting. In order to cut off the part of the laminate panel, it is enough to lay the material on the edge of the table or workbench, fix it, and with a slight effort to smoothly perform the incision along the marking line. Thanks to huge power, you can cut the laminate any thickness.

With one hand you can cut only if there is a special support heel

Note! Corner grinders cannot be cut on the basis of PVC. In this case, the fishing line for the trimmer of the cut is uneven, the plastic is paid and follows from the contact zone.

You can cut a soft wood panel with almost any cutting circle. It is best for cutting a laminate with a corner grinding laminate is suitable for a disc with a diameter of 110-125 mm and a thickness of 0.8-1.5 mm. Various kinds of diamond and nitride-based circles on a metallic basis cope with the task a little worse.

In order to cut a laminate, a small machine with a capacity of 300-500 watts is enough. In the presence of a certain experience, the incision can be performed even with one hand.

Cutting the laminate with a jigsaw

The popularity of the electrician is very great, it is used to cut out all kinds of lumber, plastic and even thin.leaved metal. There are several options for hacksaw paintings for materials for materials of various density and hardness. Usually this is a short titanium blade with sharp teeth, for metal tooth metal is 1-1.5 mm, for soft wood and plastic, the size of the cutting edge increases by 2 times.

Electricity is a convenient tool if you need to cut the cutting very quickly, as they say, “on the fly”. But a seam or a fishing line for a cutter of cut after using a jigsaw is not the most even. over, if you use a canvas with teeth of high altitudes and cut at low speed, then the cutting edge is strongly “shaggy” of laminate material.

Be sure to use guide devices

Therefore, in order to cut the laminate with a jigsaw without chips, you must adhere to the following rules:

  • You can cut the laminate only in an inverted state, the front part on the table or the supporting surface of the workbench;
  • If the back side is very soft, then the top line is best glued to the usual tape. The tape does not interfere with the movement of the teeth, while maintaining the edges of the incision whole;
  • Cutting speed is selected individually. Typically, for soft materials, high speeds are chosen when minimal supply of the canvas.

Another condition is that you can’t cut the laminate with an electrician on weight, there must be a hard support, both for lamellas and for the sole of the jigsaw. In addition, if the width of the laminate is more than 15 cm, then it is necessary to use the guide bar, which is attached to the tool case and provides smooth and uniform movement during the cutting process.

Based on the above, we can conclude that there is a wide variety of tools for cutting the coating.

You need to choose depending on the size of the room and financial capabilities.

For example, specialists who professionally engage in laying coatings should be armed with special equipment. However, those who want to make the installation of housing, can do with cheaper decisions.

If you do not have special equipment, it is not necessary to purchase it. you can cut off the laminate using a hacksaw

The primary task of the installation of the laminate is to avoid the occurrence of chips and cracks. In this regard, it is important to properly calculate everything.

You can make a cut of laminate almost using any equipment with a cutting part. It is important to do everything gently. It is worth selecting a tool based on skills, planned volume of work and means.

The most optimal solution for cutting coatings is an electric jigsaw, since this tool is universal, and certain skills for working with it will not be required.

If there are any doubts about laying and cutting the coating from the laminate, then it is best to trust professionals. There is a risk only to spoil the material, which will greatly affect the means.

Coating types

The choice of tools for cutting laminated panels largely depends on the type of planks used. If the flooring is supposed to be done independently and without the help of specialists, it is better to pay attention to soft types of laminate.

At home, it is easy to cut a soft cork or two.layer vinyl laminate. Such varieties of laminated panels are characterized by high strength and moisture protection, as well as masonry speed.

To cut this type of lamellas, you will not need a special tool, for this it is enough to equip yourself with a regular ruler, a pencil or pen and a construction knife. First, the fishing line for the cutting trimmer is circulated with a pencil or handle, and then it should be drawn with a knife. After that you just need to bend the canvas. If you need to make a curly incision, then you can use large scissors for this action.

However, for cutting other types of multi-layer panels, including high-strength wood-combustible or wood-based plates, it is necessary to choose more serious tools.

What to use at home?

When choosing a tool for cutting laminated panels, there are several factors that should be taken into account:

  • The tool should be easy to use and not cause discomfort. It depends more on personal preferences and behavior.
  • Compact and light objects are much easier and faster processed, and every minute in the account.
  • Another important point is that with the chosen tool you should get a uniform incision without chips and cracks. However, there is no need to focus too much on this factor, since minor irregularities will be imperceptibly hidden under skirting boards.

Having familiarized yourself with the main characteristics, you can proceed to a more detailed study of the tools for sawing the laminate.

One of the simplest tools for cutting the planks electric jigsaw the device is light, and even a teenager or girl will quickly cope with it. The puzzle works at high speed, so the cut is done carefully. One of the important factors when using this device is the correct choice of puzzle. Modern models are usually equipped with special variable files for working with laminate. Other files differ in shape, location and size of cloves. However, in the absence of special devices, narrow files with small cloves are also suitable for cutting metal products.

In order to avoid damage to the decorative side of the brand and all manipulations with a jigsaw with the panel should be performed on the wrong side. The fabric should be placed on the table or chair so that the cut.off piece of the strips hangs. Strongly pressing the panel with your hand to the table, you must quickly move the jigsaw along the site of the jigsaw.

For cutting the necessary pieces of laminated panels, guillotines are quite suitable. Unlike the previous device, the guillotine has a mechanical device. In appearance, it can be compared with large scissors. This cutter is quiet, simple and accurate in operation. Using it, the easiest way to cut off the laminate, but buying a cutter for repairing an apartment will be inappropriate. Such a device is suitable for those who are professionally engaged in the laying of the floor, so it can be found in temporary use from familiar repairmen.

Laminate cutting tools

If you choose tools for cutting laminate, then you should take into account a number of features.

  • It is important that the tools are convenient to use. In many ways, convenience depends on the ability to use the tools and preferences of people.
  • If the tools are low and ergonomic, then with their help you can do all the work much faster. When conducting repair work, time is a very valuable resource.
  • An important nuance when choosing a tool and a sawing is that the cut should be even, without any cracks and chips. Nevertheless, you do not need to focus on this nuance attention, since some kind of irregularity can be hidden under other elements.

Electric jigsaw

It is very simple when using the tool that allows you to cut the lamellas is a regular electric jigsaw. The jigsaw functions at very fast speeds. This means that you can make all the cuts very smoothly. An important nuance during the work of the jigsaw is the choice of a suitable tool for the tool. Today, most of these tools have in their set files for such coatings that can be easily replaced. If comparisons with other types, then they have a different shape, size and position of the teeth. One way or another, if there are no special files, you can also use standard with small teeth, which are used to cut metal products.

It is quite simple to cut the laminate with an electric jigsaw. this does not require special skills, you only need to observe safety precautions

In order not to damage the layer with the image, make notes and all actions with the tool is necessary from the inside. It is better to put the coating on the table or stool so that the cut part of the panel is suspended. Firmly fixing the element with the hand, you need to quickly walk on the planned cut line.

Bosch has laminate cutting tools. Solutions from this German company are great for work. The assortment has devices for cutting both straight and figurators. There are also tools to make narrow cuts.

Special files for an electric jigsaw from the company are presented in a wide range. So, the company has a model in which the cloves are located on the reverse side. Such a saw will not harm the coating, and the cuts will be even and smooth.

It is worth using special jigsaw files to cut the laminate

In addition to cutting the laminate, the tool can be used for work with plywood, wood-bruise and wood-fiber slab.

There is also a model that is perfect for the curly cutting of a laminate or other wood coating.

  • A narrow saw will make the cut more neat.
  • If you need to make a cut as soon as possible, then the tool with large teeth will be an ideal solution, but the risk of damage to the material will increase.
  • Always use proven equipment with all the necessary certificates of authenticity.

Step.by.step instruction of laminate cutting using an electric jigsaw

Guillotine

To incite the necessary pieces of laminate panels, you can use the guillotine. If we draw analogies with a jigsaw, then the guillotine has a device with a mechanism. Outwardly you can make a comparison with large scissors. Such a device will not make noise, and with the help of guillotine it is easy to cut across the panel. True, to purchase a tool only in order to make repairs in one room, you should not. The guillotine will be more useful for people who, on a constant basis, lay coatings on the floor. specialists. It will be better to borrow such a tool for the time.

You can use a special guillotine that will help to cut off the laminate evenly

A circular saw

You can cut it, and using professional equipment. circular saw.

Cope well with the task and circular saw

It is important to know that if you use a circular saw, then it should have a special.purpose disk suitable for work with metal products. In addition, to wield a circular saw, you need to have a certain level of skill.

When working with a circular saw, the panel is placed up and firmly fixed. You need to be very careful when working with such a tool. Always remember safety measures when working with equipment that can harm a person. Always fasten your sleeves and watch your hands.

The most budget circular saws will cost about forty dollars. Purchase such equipment to make a cutting coating from a laminate does not make sense. In addition, it is quite overall, and bring it to the house is not an option. If there is such a tool in stock, then you can produce all the manipulations with a laminate. It is necessary to use a disk for work with metal products, however, it is worthwhile to have experience so as not to damage the product and not harm your health.

Nuances for work with “circular”.

  • You need to make markings and make cuts on the front side.
  • It is important to firmly fix the part on the flat surface with a pattern upward. It is important that the lamella is installed correctly, and not so that one person holds it with his hands, and the second makes a cut.
  • If there is a machine with a “circular”, then everything is done in the same way as described above.
  • If the machine is used, then the laminate is not fixed, but simply carefully brought to the cutting disk. It is important to use protective equipment and protect your eyes.

It is important to observe safety precautions when working with a circular saw

Milling mill

For cutting laminate, you can also use a milling cutter. It is unlikely that each person has such equipment at home, however, specialists who are engaged in work with furniture products are usually always available. Using such a tool can make an ideal incision.

Circular saw. whether it is worth using it?

Using a circular saw with a disk designed for metal cutting, you can get a very neat cut. It’s much more difficult to work with such a tool than with the rest, because before cutting a laminate at home using a circular saw, you need to have at least some experience in its use.

Here are some tips on the use of such a tool:

  • In order to perform this procedure, it is necessary to lay the laminate board on a smooth solid surface with the front side.
  • Do not press the tool much, the movements should be easy.
  • The disk is moved strictly along the previously drawn line.
  • You need to cut the coating carefully, without delay and pauses.

Circular saw. whether it is worth using it?

Using a circular saw with a disk designed for metal cutting, you can get a very neat cut. It’s much more difficult to work with such a tool than with the rest, because before cutting a laminate at home using a circular saw, you need to have at least some experience in its use.

Porcelain Tile Shaping

Here are some tips on the use of such a tool:

  • In order to perform this procedure, it is necessary to lay the laminate board on a smooth solid surface with the face up.
  • Do not press the tool much, the movements should be easy.
  • The disk is moved strictly along the previously drawn line.
  • You need to cut the coating carefully, without delay and pauses.

Vinyl laminate cutting

Type of lamellas, which will be used during installation, determines in most cases the necessary tools for cutting. If it is planned to lay the coating on their own without the use of the help of professionals, then it is worth taking a closer look at the laminates of soft types.

At home, the process of sawing soft types of laminate, for example, on the basis of a cork will not represent a particular difficulty. These types of coating have increased resistance to wear and water protection. In addition, such a laminate quickly fits.

The easiest way is to cut a vinyl laminate. this can be done using an ordinary stationery knife and ruler

To cut these types of coatings, you do not need to use any special tools. You will need a simple ruler, pencil and knife. The cutting line for the trimmer of the incision should be indicated with a pencil and then just walk with a knife. Then you just need to bend the laminate. It is also possible to make incisions in the form of figures. for this you can use ordinary scissors.

Nevertheless, in order to cut other types of panels with numerous layers, where there is a particularly strong wood fiber or wood-piece plate, a special tools may be needed.

Hacksaw

This is the easiest tool, which, in principle, can be cut off the laminate. But the wood hacksaw is not suitable for this purpose. Its large teeth will make the cuts decomposed and torn, and you will have to spend too much effort. Case with small teeth are more suitable for these purposes, but still, this is far from the perfect way.

You can use a manual hacksaw designed for cutting metal products. She will practically leave no traces after herself, but the work will be long and tedious. If you need to cut several panels, then this method can be used. If there is a large amount of work, then you should choose a more effective tool.

laminate, corner, grinder, circular, requires

Corner grinder

Almost every man has this popular tool. And it can be used universally, including for the cut of laminate. But not everything is so simple here. It is important to choose the right cutting disk. If you use an ordinary cut.out disk designed for cutting metal, then nothing good will come out. The room will be filled immediately with caustic smoke, after which the work will need to be temporarily collapsed. And this is logical, because the cuts are designed only for metal.

It is also not the best option that is a disk designed to cut concrete. He will not only fill the room with smoke, but also leave behind uneven edges.

It is permissible to use a wood disk having a teeth. Only work should be very neat, since the teeth are very large.

Sawed with a circular saw

The use of a portable machine for cutting panels will make it possible to quickly and efficiently make the required amount of laminate of the desired length. The presence of skills with a portable circular will help with longitudinal processing of workpieces. If you are faced with such a professional tool for the first time, then it is necessary to perform several draft cuts, even with the usual transverse sawing of the panels.

To cut off the workpiece, it is marked on the front side. Then a disk with small teeth is installed, the equipment is launched and, clutching the panel to the horizontal bed, pushed the laminate along the intended line.

ATTENTION! The execution of the longitudinal cut requires the installation of the width on the circular machine!

The circular saw is a convenient tool for the saw, but the dimensions and weight will require special transportation of the device to the place of work. The installer independently determines the feasibility of using such equipment.

Features of cutting vinyl laminate

High resistance to erasing the upper layer, similar to commercial panels, makes vinyl coating in demand. In addition, such material creates an original decorative effect. The structure of vinyl panels is different from ordinary, softness and viscosity.

To cut such a material, it will be best to use a construction or stationery knife. This tool will cut all layers of vinyl laminate, subject to mechanical destruction.

After studying all the methods of cutting and the possible use of a particular tool, each selects the required device, depending on the task and the availability of.