DIY iron wheels on a tiller

Wheel types

First you need to figure out what types of wheels for a tiller generally exist. Since the technique is used in a variety of farming processes, the equipment may vary. This also applies to pneumatic wheels, because good results and ease of use also depend on the right components. It is important to note that ordinary car wheels from “Oka”, “Niva” or “Moskvich” cannot be put on the tiller. All of the options below are larger and heavier. It would be more correct to compare them with ATV kits, although they do not always have the right size.

• Pneumatic. This option can be supplied for arable work and for removing roots from the soil. In appearance, these are large wheels, with a diameter of 40 cm and a width of 20 cm. The pattern on the tread must be rough in order for the tiller to work well on the soil. Often this option comes standard and is renowned for its durability. However, if they become unusable, then you should immediately look for a replacement.

How to make iron wheels tractor ,Make plowing tractor

• Traction. The popular name for these wheels is a herringbone. All because of the pronounced pattern on their rubber. This look is also versatile and suitable for lug or standard transport solutions. For example, they are often used by snow blowers. Traction tires for the tiller are also reliable in everyday life.

• Solid (most often made of rubber). One-piece configurations are ideal for rocky ground. They allow the tiller to move faster on such terrain and do not deteriorate after the first use. Of the minuses, they are really very heavy, so it’s not so easy to transfer them. Similar tires are suitable for MTZ series trailers and diesel vehicles.
• Metallic. The last variation is suitable for clay soil. The thing is that, unlike the previous wheels, these have steel teeth. This, of course, makes the technique heavier, but in soft ground they do their job perfectly. In another way, metal teeth are also called lugs.

As for general recommendations, when choosing what to wear your tiller, pay attention to the front wheel. It is supporting and in the process of use absorbs the entire mechanism. This helps to extend the life and improve the quality of work.

In general, this classification of pneumatic wheels is applied not only to the tiller, but also to trailers or other tools from the same category. So you can safely use it, because to maintain the durability of all equipment, the farmer’s assortment should include both a trailer and a tiller.

Making wheels for the tiller with our own hands

tiller is a technique that most farmers are familiar with. In fact, it is a mobile tractor that is used for plowing soil, planting plants or transporting goods. It is convenient in small suburban areas, where it is already difficult to do everything with your hands, but a large tractor is not needed. If you are reading this article, then you either already have a tiller, or you are going to purchase one.

One of the most frequent questions of the owners of this technique is how to make wheels for a tiller with your own hands? The thing is that, as standard, they wear out very quickly, and are also not suitable for all types of soils and reliefs. Buying new ones is quite costly, so you can resort to your own skill. This article will look at exactly how to do this.

How to make wheels with your own hands

Having dealt with the types of tires, you should learn how to make the same, but homemade. The first thing to consider is that you won’t be able to make wheels for a tiller from scratch anyway. You will need a base. old pneumatic wheels from a car, for example, from “Oka” or “Niva”. In this matter, it all depends on your choice or the availability of suitable material. And by the way, farmers do not recommend buying a new set of tires for rework, as they are not cheap and as a result, you will not be able to save a decent amount by doing the rest of the work yourself.

The second thing, without which nothing will come of it, is to prepare the drawings before starting the process. This issue must be approached responsibly, and the drawings must meet the requirements based on the available materials.

Paired wheels are often made, where an additional weighting agent can be placed inside. Let’s start with this option. The tandem version is a quick and efficient wheel conversion that is available to many. You will need 4 wheels with a good base made of stainless steel (by the way, the masters have tires from Moskvich). You also need to have iron plates with you. The process itself is carried out in several steps.

• The rubber tire is removed from the base.
• To the rim on which the tire is put on, it is necessary to weld several plates of iron, up to 5 cm wide.Usually, a square is formed from the plates, which is welded to one of the sides of the rim.
• Next, the rim from the second wheel is welded to this square. Thus, you connect the two rims to each other using plates and welding.
• At the last stage, the rubber is put on again on the rims.

That’s it, you’ve got the kit you need. As you can see, their main advantage is their large width. Thanks to this, they look less like wheels from a car, and more like an option for a tiller.

The second option, how to strengthen pneumatic wheels, is to increase their wear resistance due to additional materials. In this way, you can remake the wheels of a transport vehicle such as a motorcycle or ATV. In general, you will need larger tires than a regular passenger car. Large chains can be used to increase rigidity.

Let’s move on to the process itself: chains need to be welded to pneumatic wheels. You can try connecting them with rubber or with an iron rim. Next, you need to make notches on them so that they imitate the lugs. The result should be similar to purchased metal wheels.

You will have to tinker with this method so that the chains hold tightly and do not fly off during work. This is where blocking chains with a rim comes in handy, which can be done with steel fasteners and hooks.

An additional element that is often lacking for the convenience of working with a tiller is an unblocker, sometimes called a differential. Since the instrument itself is heavy, it is often difficult to control it, namely, to turn in different directions. In this case, an unblocker comes to the rescue. a special device that is attached to the wheels and increases their maneuverability in difficult areas.

The release tool is bolted to the output shafts of your tiller. During operation, it reduces the turning radius of the entire machine and increases the track width. If you use a mini tractor on a regular basis, then this thing is simply irreplaceable. You can make an unblocker yourself based on bearings, but in fact. the game is not worth the trouble. On the market they can be found in a wide variety of variations, and unlockers are inexpensive. The most important thing is to find a specialist who will advise on a good product.

So, if you have a need for a new “shoe” for a tiller and you can use tires from a regular car or motorcycle, then why not give it a try. This article lists the simplest and most popular options, but it all depends on your experience and skills. In fact, the solution is very simple, you only need welding and a little skill. But for a good result, consult with experienced craftsmen before starting work.

To learn how to make wheels on a tiller with your own hands, see the next video.

Wheels for a tiller: an overview of the types, how to do it yourself

In most cases, before buying a tiller, people pay special attention to the practical characteristics of the device, without being interested in the quality and features of the wheels. Such an approach can hardly be called literate, because the quality and duration of the equipment itself depends on the specified details.

Since the specified unit is a multifunctional device, different wheels are offered for the tiller:

• pneumatic;
• traction wheels;
• solid rubber options;
• metal wheels with grousers.

To clearly understand the specifics of each type, you should consider their features in more detail.

Pneumatic

These options are perfect for frequent plowing and digging up root crops. An important point: in no case should the width of the wheels be less than 20 cm, and the diameter. 40 cm.Aggressive tread pattern will be a huge plus.

The pneumatic components contribute to the incredible stability of the unit, but if damaged they must be replaced. They are often sold as wheels for Neva tilers.

Traction

These products have another name: “herringbone”, and all thanks to their versatility and interesting tires. The increased grip width allows them to perform the task of both lugs and classic transport wheels.

What’s more, the traction options are suitable for trolley and snow blower, and also help to cope with off-road conditions. Durable premium rubber for durability and long service life.

Solid cast

For rocky ground, due to which many types of wheels deteriorate very quickly, solid products are ideal. Let them weigh a little more than the above wheels, but they do not drift.

These products have the most powerful tires for the tiller, therefore, they are bought for diesel types transformed into mini-tractors. For MTZ tillers, solid ones are considered ideal options.

How to make wheels for a tiller with your own hands?

It is necessary to understand that it is impossible to make wheels from scratch with your own hands. It is necessary to find the basis and only after that you can begin to form improved and useful devices.

As this very base, you should use wheels from a motorcycle or from a car. You can only create a homemade version with a lug, because if wheel weights are not used so often, there is no point in purchasing new expensive products. On our website you can find a specialized article, where all the features of creating lugs with your own hands are considered in detail.

To expand the wheelbase, it is recommended to use extension cords for tiller wheels, because it is necessary to correctly adapt the device to the individual needs of the farmer. over, to expand the possibilities, you can create twin iron wheels that have a cavity inside to accommodate any weighting agent.

Yes, these objects can hardly be used for a trailer for a tiller, but they will be very useful for the unit itself, because they can be created if a person does not have wheels from a motorcycle, but are available from a UAZ or Moskvich. The advantages of twin wheels:

• reduced towing, and, as a result, increased productivity levels;
• the ability to quickly remove the wheels of the outer plan;
• ease of creation at home;
• maximum contact with the surface.

Twin wheels are gradually becoming more and more popular, because you can spend a little time on their independent creation.

Metal with grousers

Such wheels have a certain weight, therefore, they are distinguished by additional power. The steel teeth “push” the machine forward and prevent it from loading even in the most clay soil.

Particular attention must be paid to the supporting front wheel, which carries a considerable load. It contributes to the optimization of land work and increased endurance of the tiller itself.

Trailer wheels have a similar classification and are selected according to the same principles. Do not forget that in the process of transporting heavy loads, low pressure is exerted on the wheels of the tiller itself, and high pressure on the wheels of the cart (trailer). Therefore, in this case, you need to choose the most durable options.

How to make twin wheels yourself?

Of particular interest among farmers was a simple and even a little rude, but effective method:

• First you need to find suitable wheels with tires;

DC Motor Power Tiller Iron Wheels Agricultural Tractor. How to Make Ploughing Tractor

• Then it is advisable to cut small protectors on them;
• The next step is that people buy a 5x50mm strip of steel, weld 250mm squares and insert them into the rim;

• After welding, the second wheel rim is set up and objects that look like vases are obtained;

• Upon completion, the tires are put on the rims obtained and the paired wheels are ready for use.

It is not difficult to obtain such useful devices, the main thing is to decide which options are needed and select all the necessary “ingredients”.

Support wheel

Most modern chiller models are complemented by one support wheel. It is he who accounts for all the load from the motor and other mechanisms that are located in the front of the motorcycle.

This support wheel increases the durability of the tiller and also optimizes its performance.

How to make extension cords?

• Prepare two pipes with a diameter two millimeters larger than the axis of the unit;
• Make a thread for screwing in the extension cords on the axle;
• On the reverse side of the pipe, there should be holes two millimeters thinner than the holes in the discs on the wheels. If necessary, the pipes are sawn off;
• Wheels are fixed on extension cords with steel plates, they are bolted.

Wheel extensions are installed on the output shafts of the tillers. During mounting, it is checked how secure the fastening and the tightness of the fixation are.

Solid wheels

Tiller wheels are solid rubber with aggressive tread pattern. This feature allows them to be installed also on mini-tractors.

Due to their rather large size, these wheels are most often used in difficult terrain, in wooded and mountainous terrain.

Twin wheels

These wheels have two parts, they have the same dimensions and shapes. Due to their design, they provide excellent permeability of the tiller on uneven surfaces, significantly increase its speed on a flat road.

With such wheels, towing is practically excluded. Therefore, they are often mounted during winter.

Making paired wheels with your own hands

When using equipment in conditions of increased complexity, you need to acquire twin wheels. Double elements are made according to the following scheme:

• Protectors are cut on suitable wheels;
• Squares of 2525 cm are welded from steel pieces, which are installed in the central part of the rim;
• After welding, a second rim is installed. You should get a product that resembles a vase;
• Tires are mounted on joint rims.

For the manufacture of paired parts, you will need rims of the same size.

Metal wheels with grousers

This type of wheel is quite small. But the power and endurance of the unit is provided by the presence of weighting materials.

The construction also includes steel teeth. Their task is to push the tiller forward, preventing towing even in the smallest area.

Making wheels for a tiller with your own hands

It is impossible to make wheels on Tilleri without blanks. It is necessary to prepare the basis, which is further modified and improved.

Simple manufacturing guidelines:

• you can use motorcycle or car wheels as a base. To change the track width, special axle extensions are used. With their help, you can make wheels for the implementation of specific tasks;
• tires for the tiller are matched to the type of soil. For sticky, uneven ground, studded tires with an aggressive tread pattern are suitable;
• homemade wheels are large enough. Otherwise, they will not cope with the work. Wheels of small diameter slip, so they often have to be pulled out of wet soil;
• optimally make wheels from car rims.

Work algorithm:

• Two wheels will take four discs out of the car. They are deburred with a file;
• Discs are welded together with convex sides;
• Rubber chambers are put on the prepared wheels;
• At the last stage, the wheels are inflated with air and installed on the tiller.

So that during manufacturing there are no difficulties, it is worth watching the video.

Homemade iron wheels on tiller

tiller is a technique that most farmers are familiar with. In fact, it is a mobile tractor that is used for plowing soil, planting plants or transporting goods. It is convenient in small suburban areas, where it is already difficult to do everything with your hands, but a large tractor is not needed. If you are reading this article, then you either already have a tiller, or you are going to purchase one.

One of the most frequent questions of the owners of this technique is how to make wheels for a tiller with your own hands? The thing is that, as standard, they wear out very quickly, and are also not suitable for all types of soils and reliefs. Buying new ones is quite costly, so you can resort to your own skill. This article will look at exactly how to do this.

Homemade lugs for the tiller. YouTube

Running trials of lugs for a tiller and a motor-cultivator. Transport Wheels and Efficiency of Unblockers.

Auto rides on wood | Topic author: Auni

The video was deleted or is not publicly available

Vladislav (Auni) To increase the speed in front of you need to let the cat go. In childhood I used to do this. I tied the dog to the bike and if he saw a cat on the road, then the speed was excellent. Then the cat went into the hole in the fence, followed the dog, and I went into the fence. as a result, a bunch of iron from a bicycle, I was all skinned with bruises, bumps and abrasions.

Tags: How to make iron wheels for a tiller video

Homemade Tiller Lugs. YouTube

Homemade lugs for the tiller. tiller Bison NT 105. Made a MINI Tractor with an engine and a rear gear from.

Wheel types

First you need to figure out what types of wheels for a tiller generally exist. Since the technique is used in a variety of farming processes, the equipment may vary. This also applies to pneumatic wheels, because good results and ease of use also depend on the right components. It is important to note that ordinary car wheels from “Oka”, “Niva” or “Moskvich” cannot be put on the tiller. All of the options below are larger and heavier. It would be more correct to compare them with ATV kits, although they do not always have the right size.

• Pneumatic. This option can be supplied for arable work and for removing roots from the soil. In appearance, these are large wheels, with a diameter of 40 cm and a width of 20 cm. The pattern on the tread must be rough in order for the tiller to work well on the soil. Often this option comes standard and is renowned for its durability. However, if they become unusable, then you should immediately look for a replacement.

• Traction. The popular name for these wheels is a herringbone. All because of the pronounced pattern on their rubber. This look is also versatile and suitable for lug or standard transport solutions. For example, they are often used by snow blowers. Traction tires for the tiller are also reliable in everyday life.

• Solid (most often made of rubber). One-piece configurations are ideal for rocky ground. They allow the tiller to move faster on such terrain and do not deteriorate after the first use. Of the minuses, they are really very heavy, so it’s not so easy to transfer them. Similar tires are suitable for MTZ series trailers and diesel vehicles.
• Metallic. The last variation is suitable for clay soil. The thing is that, unlike the previous wheels, these have steel teeth. This, of course, makes the technique heavier, but in soft ground they do their job perfectly. In another way, metal teeth are also called lugs.

In general, this classification of pneumatic wheels is applied not only to the tiller, but also to trailers or other tools from the same category. So you can safely use it, because to maintain the durability of all equipment, the farmer’s assortment should include both a trailer and a tiller.

How to choose wheels for a tiller and how to make your own.

How to make a homemade tiller from a motorcycle engine, photo video. as well as metal wheels with grousers. for high-quality.

Do-it-yourself attachments for a tiller from car disks

Before starting work on the manufacture of a lug, you need to acquire drawings, the orientation of which will be aimed at the work process. The simplest and most common manufacturing method is considered to be the use of car wheels for it.

Step-by-step instructions for making lugs from discs:

Using a welding machine, a strip of metal is attached to the discs, which will later serve as a fastener for the lug plates.

Making teeth based on steel plates. The thickness of the plate must be large enough if the attachment is designed to work with the ground. The length of the teeth must be selected based on the tiller model.

The teeth are fastened in a circle, the distance between them should be 16 cm, the permissible deviation in different directions should not exceed two centimeters.

If the owner of the tiller correctly made a lug with his own hands from car disks, then in no case will he be disappointed, but, on the contrary, he will have a desire to work and share his experience in the future.

When putting into operation your lug, it is worth remembering its direct purpose, that is, its contact exclusively with the ground. It is strictly forbidden to operate the equipment on hard surfaces such as stone or asphalt.