September 12, 2019

Dog Box Do-It-Yourself With Detailed Drawings, Photos

Dog Box Do-It-Yourself With Detailed Drawings, Photos

A drawing of a dog box with sizes and photos. How to build a dog house, detailed instructions.

How to make a simple booth for your pet? In this article we will look at all the steps in the manufacture of dog booths.

How to make a dog house with your own hands.

For the manufacture of the booth you will need materials:

  • Timber 50 x 50 mm.
  • Wood screws – 50 and 100 mm.
  • Plywood not less than 12 mm thick.
  • Jigsaw.
  • Screwdriver or curly screwdriver.
  • Saw.
  • Roulette, charcoal, pencil.

A drawing of a dog box with dimensions.

We will make a harness from a bar for the floor of the booth, we will need 3 bars 115 cm each, and 2 bars 92 cm each. We fasten the frame of the bars as shown in the figure with self-tapping screws (100 mm).

Dog Box Do-It-Yourself With Detailed Drawings, Photos

Cut a plywood sheet 125 x 92 cm, fasten it to the frame with self-tapping screws (50 mm).

Dog Box Do-It-Yourself With Detailed Drawings, Photos

We will produce two side frames for a doghouse, for each frame we will need 2 bars of 125 cm each, and 3 bars of 58 cm each. We assemble the frames and fasten them to the floor of the booth as shown in the drawings.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

Now we will make a frame for the back wall of the booth, the frame consists of 3 bars 58 cm long and 2 bars 115 cm long. We fasten the frame with self-tapping screws to the floor and to the adjacent side frames.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

In the same way, you need to assemble the front frame, in the front frame you need to provide a place under the entrance to the booth with a width of 38 cm. The figure shows the wiring diagram of the front frame. All frames are attached to each other and to the bottom frame with self-tapping screws.

Read more:  Dog Box Photo Of Simple And Elegant Options For Backyard And Garden

We are starting to manufacture a roof for a doghouse. In this construction, a gable roof is used, for its manufacture, you will need to cut out of a bar, 8 stop lengths of 76 cm. As the roof ridge, we use a 125 cm long timber.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

We assemble the frame of the roof of the booth as shown in the diagram.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

Getting to trim the side frames. We cut out of plywood with an electric jigsaw for the wall of the booth, in the front wall we gently mark and cut out the inlet for our pet.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

In the same way, we cut out from plywood two panels for the roof of the booth, the dimensions of each panel are 125 x 77 cm. We fasten the panels to the rafters with screws.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

To prevent the roof of the booth from getting wet, it needs to be covered with a covering material, you can use sheeting, shingles or roofing felt.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

Dog box can be painted on the outside with any paint for outdoor work.

Dog Box Do-It-Yourself With Detailed Drawings, Photos

In this article, we looked at the step-by-step making of a dog house out of plywood, as you can see making such a box is not difficult. But this version of the booth is not suitable for regions with harsh winters, if you need to make a warmed booth, we recommend reading the article with step-by-step instructions, detailed drawings and sizes – how to make a warm dog booth.

SHARE:
Dog House 0 Replies to “Dog Box Do-It-Yourself With Detailed Drawings, Photos”
anna_stevens