July 23, 2019

Dog Box With Their Own Hands Using Drawings

It is possible to build a convenient doghouse for a dog from simple materials in a matter of hours. It is very important to choose the size of the dog’s house so that the home caretaker feels comfortable at any time of the year. In addition, a dog house built with its own hands can also become an additional decoration of the site if you use the original design and decorate it properly.

Dog box with his own hands

Drawing drawing booth

Dog Box With Their Own Hands Using Drawings

Dog box with his own hands

In order to properly make a booth, you must decide on its shape and size. It is not necessary to build too complex a structure: the presence of extra partitions, ladders, protrusions and similar elements will greatly interfere with the dog. The best option is a rectangular doghouse with a side entrance and a lean-to roof, where your pet can bask in the sun. It is desirable to make the roof or one of the walls removable, which will allow you to quickly and easily disinfect the booth.

Dog Box With Their Own Hands Using Drawings

Doghouse

The size of the booth must correspond to a specific dog, so when drawing up a sketch, it is imperative to take measurements: height at withers, length from nose to tail, chest width and height of the dog.

Based on this, you can determine the parameters of the frame:

  • the width and height of the booth is equal to the height of the dog 5 cm;
  • the depth of the booth is 5 cm longer than the length of the animal;
  • the width of the manhole corresponds to the width of the chest 5 cm;
  • height of the manhole is more than the height of the dog at the withers by 5 cm.

To calculate the parameters of the booth for a puppy, you must use data from specialized directories. So, on paper they draw an approximate design drawing, transfer to it all the necessary measurements. It remains to determine the materials for the booth. Most often houses for dogs are made of wood; This material is the most environmentally friendly, convenient in work, inexpensive. The use of conifers is especially recommended.

Tools and materials for work

Dog Box With Their Own Hands Using Drawings

Materials for work

In order not to be distracted during the construction process, everything you need to be prepared in advance:

  • dry timber 100×100 and 100×50 mm;
  • cut board 25 mm thick;
  • clapboard for plating;
  • plywood sheet or chipboard;
  • bars 40×40 mm;
  • Styrofoam;
  • ruberoid;
  • glassine;
  • antiseptic impregnation;
  • sand;
  • galvanized nails;
  • door hinges;
  • hammer.

Boards and bars before assembling should be carefully cleaned, otherwise the dog may skew paws. But it is better to process wood by impregnation at the end of work, and only from the outside: foreign odors cause irritation in animals, so the dog may refuse to enter the booth.

Video – What should be a doghouse

Build a shed roof

Most dogs like to lie on top of the booth, so for them it is more convenient to houses with a lean-to roof. The roof should be under a small slope and always open – this design simplifies cleaning and disinfection of the booth. To protect your pet from the cold, the house should be carefully insulated, and it is better to do it right away, at the assembly stage. For the same purpose, the manhole is recommended to be placed on the wide side of the booth with an offset to one of the corners. So the room will not be blown and the dog will have a cozy and warm berth.

Read more:  How To Make A Booth For Two Dogs With Their Own Hands

Dog Box With Their Own Hands Using Drawings

Layout and cutting of bars

Step 1. Making the bottom frame

Dog Box With Their Own Hands Using Drawings

Making the bottom frame

Making the bottom frame

Dog Box With Their Own Hands Using Drawings

Making the bottom frame

Bars 40×40 mm cut along the length and width of the bottom, placed on a flat platform or on a table, connected with screws into a rectangle. If the animal is large, additionally strengthen the frame with one or two crossbars from a bar. After that, the frame is sheathed with boards on one side.

Step 2. Floor insulation

Dog Box With Their Own Hands Using Drawings

The photo shows the option of insulation foam, which fits between the bars and sewn boards

The frame is covered with planks so that the bars are on top. They line the inner surface with glassine, attach it with stapler brackets, and then cut the foam to the frame size and tightly place it between the bars. The height of the insulation should correspond to the height of the bars. On top of the foam is covered with another layer of glassine and fill the finishing floor.

Step 3. Assembling the booth frame

Dog Box With Their Own Hands Using Drawings

Assembly frame booth

A bar of 100×100 mm is sawn into 4 parts: 2 lengths equal to the height of the booth, 2 to 7-10 cm longer. These bars need to be fixed in a vertical position at the corners of the bottom. Racks of greater length set in the front, and those that are shorter in the back. It is necessary for the formation of the slope of the roof. Each bar is set to the level and fixed with nails or screws. Additionally, vertical bars are filled in the center of the walls and 2 smaller bars at the sides of the manhole. At the inner joints to strengthen the frame using metal plates.

Step 4. Wall cladding

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

The finished frame is sheathed with clapboard outside, and warmed from the inside: first, the walls are closed with glass asphalt, fastened with a stapler, and then the space between the bars is filled with mineral wool or pieces of foam. On top of the insulation cover with another layer of glassine, on top of which stuff plywood, chipboard or other similar material. The plating should be fixed with galvanized nails of a small size, carefully putting down the caps so that the dog does not get hurt.

Read more:  How And What To Insulate The Dog House

Dog Box With Their Own Hands Using Drawings

Step 5. Making the roof

For a shed roof, you will need an OSB sheet and 40×40 mm bars. From the bars churn the frame to the size of the inner perimeter of the kennel. From OSB cut a piece of the same size and stuffed it on the frame. Between the bars tightly laid foam, cover it with a film, fix it with a stapler around the perimeter. Then they take a larger sheet of plywood and put it on top so that the back and sides of it cover the lower frame by 10 cm, and the front is 15-20 cm. This is necessary to protect the walls and manhole from rain. Instead of plywood or OSB, you can take boards with a thickness of 20-25 mm. The finished roof is fixed to the booth with the help of loops, and roofing material or soft tile is stuffed on top.

Dog Box With Their Own Hands Using Drawings

Step 6. Finishing

Dog Box With Their Own Hands Using Drawings

The finished structure outside is treated with conventional antiseptic or special impregnation, well dried. Next, ruberoid is nailed to the bottom, bending the edges 5 cm to the walls, and two bars of 100×50 mm are attached to the ruberoid. Bars are also carefully covered with a primer mixture. Again, turn the booth, make out Laz and the ends of the crate with wooden platbands.

Dog Box With Their Own Hands Using Drawings

The roof is additionally sewn with a sheet of roofing iron and painted.

Step 7. Installing the booth

Dog Box With Their Own Hands Using Drawings

The booth is ready, and now you need to choose the right place for it. It should be a dry flat area, not far from a residential building, closed from the wind. It is advisable to choose a well-lit place next to any canopy or tree so that the animal can hide from the heat. Of course, the dog must have an excellent overview from his seat in order to notice outsiders in time.

Booth with a gable roof

Dog Box With Their Own Hands Using Drawings

Booth with a gable roof

Dog Box With Their Own Hands Using Drawings

Booth with a gable roof

Gable roofs are best done on small-sized booths, since lifting heavy structures when cleaning is not very convenient.

Dog Box With Their Own Hands Using Drawings

How to build a dog house

Step 1. Build the frame

From 4 bars 50×50 mm they knock down the bottom frame according to the drawing. In the corners, they nail the vertical posts along the height of the booth, connect them with top strapping from the same bars. To strengthen the frame fill additional jumpers on the bottom and on both sides of the manhole.

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Step 2. Fastening the roof

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Fastening rafters to the frame bar

Dog Box With Their Own Hands Using Drawings

Rafters and skate

Dog Box With Their Own Hands Using Drawings

Dog Box With Their Own Hands Using Drawings

Two identical bars 50×50 mm are interconnected at an angle of 40 degrees. Then make another exactly the same billet. They are placed on top of the booth frame flush with the walls, leveled vertically, and baited with nails. From above they connect both gables with a longitudinal beam, which should protrude 20 cm forward on one side. Cut another 2 bars of the same length and stuff them on the lower ends of the rafters.

Read more:  Doghouse Do It Yourself

Step 3. Booth trimming

Dog Box With Their Own Hands Using Drawings

House house plan

The finished structure from the outside is sheathed with clapboard. Boards should fit snugly together so that there are no gaps. The bottom is additionally upholstered with roofing material, if necessary, fix the support bars.

Step 4. Warming

The photo shows the inner lining and a layer of insulation

From the inside, the frame is lined with glass asphalt, which is fixed with a stapler in the corners, after which the foam or mineral wool is inserted. Further, the heater is closed with glass purse and plywood is filled on the walls and floor.

Step 5. Roof trimming

Dog Box With Their Own Hands Using Drawings

The frame of the roof is removed, sheathed inside with plywood, then turned over, asphalt is fastened over the plywood. The space between the bars is filled with insulation, the top is covered with glass arch, and after that the professional flooring is fastened with screws. At the junction of the slopes mount the ridge, the front edges closed end strips. To make it convenient to remove the roof, they hammer in the ends of the corner posts on the nail, grinding off caps. In the bars of the pediments, drill holes through the diameter of the nails and then simply put the roof on.

Booth with vestibule

Dog Box With Their Own Hands Using Drawings

Booth with porch

To make a home for a dog more comfortable, you can build a booth with a vestibule. This is a construction consisting of two compartments: the far one is a berth, and the nearest one protects from drafts and cold. The warmed partition with a manhole divides them.

Video – Insulated booth with vestibule

You should not make the bed too big – usually the dogs sleep, curled up. But the size of the vestibule should be such that the dog could freely stretch out to its full height, and also easily pass through the manhole and unfold in the booth. The assembly of the kennel with the vestibule is performed as standard; the only difference is the partition: for its manufacture will require bars 40×40 mm, a piece of plywood, insulation and screws. From the bars make the frame width and height of the interior. Plywood is cut into two parts; One part is nailed to the frame, a heater is inserted between the slats, and the second part is covered with plywood. For the partition to be freely removed, take two wooden slats and with the help of a cutter choose in them the longitudinal grooves on the thickness of the partition. Then screw them to the walls of the booth and insert the partition.

SHARE:
Dog House 0 Replies to “Dog Box With Their Own Hands Using Drawings”
anna_stevens