Drilling passage holes in the walls. How to choose a drill?

Drilling holes in the walls

When landscaping the apartment, there is a need to attach all kinds of items on the walls and ceiling. photographs, paintings, lamps, mirrors, curtains, shelves, TV, skirting boards and much more.

In order to hang a photo or a small picture, of course, you should not drill the wall. It is enough to score a small nail. Not every clove is suitable for this matter. It is best to use dowel. Nails from fasteners, which are fixed on the walls of computer network cables. These carnations of sufficient length, thick and hardened. It turns out to score even into the concrete wall.

Performing the operation of drilling holes in the walls with modern equipment with a power tool will not present more difficulty if you know how to properly perform drilling. Will save you from unnecessary cleaning and save property in integrity if you apply a conductor for drilling without dust.

Than drill the wall

The best tool than the peorator for drilling holes in the brick and concrete walls has not yet come up with. But rarely anyone can afford to have a luxury to have such an expensive tool on the farm. Usually buy an electric drill of shock action.

The choice of a drill

When buying an electric drill, you must be guided below by the following technical characteristics.

The power of the drill should be at least 600 watts. Revolutions up to 2500 per minute and the possibility of their smooth adjustment from zero to maximum. The presence of a rotation reverse (switch of direction of rotation of the drill clockwise or counterclockwise). The cartridge is best fast.packed, it will not be necessary to spend time on the click of drill and the search for a constantly lost key. The diameter of the drills clamped in the cartridge up to 12 mm.

The presence of the inclusion function with a blow. Of course, the drill when this function is turned on will not become a full.fledged peorator, but drilling the walls will be much easier and faster and that’s why. Brick, cement and concrete are very well withstanding a static load. pressure. But easily destroyed from dynamic influences. impact. Karatists, due to a strong blow, easily break the brick in two of the edge of the palm. When driving a drill without a function of impact, a simple pressure of the drill and cutting edge is difficult to catch on the material, so the drilling goes slowly and the drill from friction is greatly warmed up. Completely differently take drilling with a blow. The drill, when impact, crushes part of the material with the cutting edge, and, getting with a blow to the depression formed, breaks off a portion of particles of the material. Something happens on the likeness of a chisel of a chisel.

The choice of drill

Walls made of wood, drywall, foam concrete are successfully drilled by ordinary drill. For walls made of brick, stone or concrete, a carbide drill is already needed. It differs from steel, it differs on a conventional drill with cutting edges of carbide material, usually winning. Less commonly artificial diamond.

The winning insert is clearly visible at the end of the upper drill. It is enough to have 2 winning drills with a diameter of 6 and 8 mm on the farm.

Drill with a winning surfacing can drill a hole with a depth of not more than 10-15 cm. For drilling to great depths, for example, to drill the wall through, use a drill. Boers for drilling brick and concrete walls are up to one meter long and are designed to drill holes only by a pedorator. In the drill, even the cutting edges are made not sharp, but rounded to increase their wear resistance. A drill with a penal function can also be successfully drilled with drill.

I am drilling rooms with a shank diameter of 10 and 18 mm, with special grooves of the SDS or SDS-Max standard for fixing, but in the usual fist cartridge are also well clamped. The standard and diameter of the drill are knocked out on its shank.

If you need to go through a thick wall with a drill, for example, half a meter, then the passage is performed in several stages with drilling with one diameter, but of different lengths. This is necessary for safety and faster drilling. First, the wall is drilled with a drill with a length of 20 cm to a depth of 10-15 cm, then a longer drill to a depth of 30-35 cm and end with drilling with a length of 50 cm. The drill for such work should be quite powerful. Of course, the drill for such a load is not calculated and its use is permissible only in exceptional cases. It is better to carry out this kind of work, to rent a real peorator.

PRICE

Diamond drilling

Masterfully drill a hole in concrete, monolith, reinforced concrete, FBS blocks and brick

Additionally, we will produce a water collection, we will take out the garbage.

During finishing repair, we use dry drilling technology without dust.

It is possible to drill walls without fixing. manual installation and telescopic stand.

A drill hole “into the ceiling”. Vertically from the bottom up.

The Almaz Best team produces diamond drilling of the openings of the software and the plug of commissioning of technical life support networks. plumbing, ventilation and electric power systems; water treatment, heating, septic tanks, air conditioners, and other needs. We have been operating since 2007. We have a park of European equipment in the required quantity. We give warranty obligations under the Civil Code.

We drill holes in the wall with tiles

In the event that it is necessary to drill a hole in the wall, which is covered with tiles, it is necessary to use special diamond crowns for tiles. First, it is necessary to drill the hole of the desired diameter in the tile, reaching the brickwork or concrete, and then with the help of a peorator and drill, continue drilling the wall.

During the drilling of the tile, the drill will heat up, so to cool it you can put a container with water nearby. If the tile is also located on the back of the wall, it is important to carefully measure and determine in which place the boat will come out. It is best not to destroy the masonry, to carefully dismantle one tile.

How to drill a wall

Before drill a hole in the wall, you must familiarize yourself with the algorithm for conducting work. At the first stage, marking is carried out. Then you can proceed directly to the process itself. First, the tool turns on several times to outline the future hole. In the process, the drill should be periodically removed, and the tool should be allowed to rest so that the equipment does not overheat, and the engine does not fail. Some masters dipped a drill into cold water.

How not to get into the wire

First you need to ask where the wiring is located in the wall. This will help you with the electrical wiring scheme. If it was not possible to find it, you must think about how not to get into communication.

To determine the location of the wires, you need to use the detector. It is applied to the place where it is supposed to be drilled. The device, however, has an error of several centimeters. In order not to get into the wiring in the ceiling, you should see where the lighting device and the switch are located. From the first to the second, the wiring goes along a flat trajectory without tilting.

In order to exclude unpleasant consequences, the wiring before starting work must be de.energized. Then, if you could not get into communication, at least you exclude the risk of a shock. Now you know how not to get into the wiring when drilling a wall. But immediately after the completion of the manipulations, the machine should be turned on. If it does not knock it out, everything is in order, and the wiring remains in integrity.

Drilling holes in reinforced concrete

On the surface of the wall, marking should be made. The tool first turns on at low speeds to make a small recess. When it is supposed to install plastic dowels, the hole needs to be made a little deeper. It is important to consider that dust will accumulate inside the recess, which is not always realistic to remove from there, so when calculating the depth, a small stock should be laid.

Drilling tiles

When the choice of drill has already been made, you can proceed to work. If you have a wall trimmed with tiles, you need to prepare some tools and materials:

When the recess is supposed to be made small, you should stock up on the equipment, which is known among the masters as a ballerinka. In the central part of the future opening, the enamel of the cladding is slightly broken up, for this the tool is installed at low speeds.

At the point of drilling, the island is glued so that the drill does not slip. An alternative and more technological solution is the use of a conductor, which is a board with holes.

Attention! It is better to drill into a concrete wall in a blow mode, but in the case of tiles this cannot be done in any way. The absence of this mode ensures the neat operation of the drill.

First, the tool is turned on at low speeds, and then the rotation speed increases. With the help of a vacuum cleaner, the second person will immediately remove dust from under the equipment.

Drilling holes of large diameter in the wall

When you do not plan to get into the wiring and know how to avoid this, you should also ask how to make a hole of an impressive diameter. If you work in accordance with the recommendations, the result will justify expectations. If necessary, make a hole at 150mm, you should use the winning drill. If this parameter should be higher, you need to purchase a screw boat.

Drilling depth limiter

When choosing such components, you need to be guided by the diameter, which should turn out in the end. This element consists of two parts, one of which will contact the surface and will not damage it. Typically, such a limiter is purchased with a screw fixation. The uniqueness of this addition to the instrument is that it eliminates the skew of the drill. Included with this device is a playback key. It is fixed on the drill.

Accurate drilling holes

Sometimes when drilling holes in the wall requires high accuracy. In order to achieve a positive result, you should glue a sheet of sandpaper by the conductor. The area of ​​the element will be affected by the area where the future hole is located. This will increase the clutch of the wall with the device, and the master will be able to make a recess in the place where it is necessary.

Arising nuances when drilling

You need a pencil or level to mark the marking. You need to drill in a mask and goggles. In front of the process, a metal detector is looking for wiring.

During the process, it is necessary to press the device very smoothly, not forgetting that the drill is heated. Therefore, you often need to cool it in water. But it should not fall to the surface of the apparatus.

There are walls composed of burnt material. Then the process is possible at low speeds during the inclusion of the shock mode.

To do the work faster, you should use the drilling rig, which provides for spraying from the diamond. If it is necessary to obtain a hole in the diameter, which exceeds 30 millimeters, you will have to purchase cern.warrils.

During operation, the device is kept at right angles to the wall.

The peorator significantly accelerates the drilling. So that the tool does not break, when there is a need for more than one centimeter in diameter, use several drills, starting with 2 mm, and ending with 10 mm. Thanks to this, the process itself accelerates.

To obtain a shallow hole with a small diameter, a manual method is used. Putting the marking, the chipper is beaten along the brick face, then the hukebur is attached with a hammer.

To install ventilation, air conditioners, electrical wiring, you need to use the automatic way of drilling.

Thanks to the work are performed quickly. Dust does not fly around the room. Holes can have a diameter of 50 centimeters.

How to drill a brick wall with your own hands

During the repair, communications or when redevelopment, it becomes necessary to produce a different number of holes in the walls.

Drilling tools and technique will differ depending on the material of the walls.

Before drilling a brick wall, it is recommended to use some practical tips, since such a durable material as brick sometimes requires a special approach.

Necessary tools and their choice

Incorrect selection of the tool and type of drill will not only not allow you to get the desired result, but can also spoil the equipment. Two types of equipment are used to drill brick. this is a peorator or shock drill.

The correct choice of a drill, first of all, lies in its power. The minimum power of this tool should be at least 600 watts, and the minimum number of revolutions. from 2500 revolutions per minute.

It is better if the mechanism has a reverse rotation of the drill and the ability to smoothly adjust the power.

drilling, passage, holes, walls, choose, drill

Drilling holes in a brick should be carried out by a shock drill, since the walls of this material are very strong to static loads, and are subject to only shock effects with a dynamic load. If you drill a conventional drill, the process will be long and ineffective, since the edge of the drill will not be able to catch on the internal structure of the brick. In this case, overheating of the tool and damage to the drill is possible.

In addition to the use of electrical equipment, there is the possibility of using a manual tool. the so.called playback. It is a pipe with teeth at the end, which the hole breaks through by applying the physical strength of a person.

In addition, the following tools will be needed:

In order for drilling holes in the brick wall effective, it is necessary to use drill with a certain diameter made of carbide material.

Their difference from the usual is the presence of a diamond or winning cutting edge. At a hole depth of up to 15 cm, you can use drills with a diameter of 0.6 or 0.8 cm. The maximum diameter of the hole that can have a drilled brick by drill is 1.5 cm.

If you need to drill a through hole of a much larger diameter, it is better to use a drill that is installed on a peorator and a shock drill. The size of the drill depends on the depth of the hole. If it is necessary to drill holes in the wall 60 cm wide or more, to speed up the process and its effectiveness, it is recommended to use drilling of the same diameter, but of different lengths at different stages of drilling, for example, start with a drill with a length of 15 cm, and at the final stage. 50 cm long.

The maximum diameter of the drilling hole can reach 2.8 cm.

To install boxes for sockets, switches, you need to create a niche. In this case, crowns are used for a peorator, which are made of strong steel and allow you to get a large diameter. Drilling with crowns is carried out without the use of shock function, and their choice depends on the diameter and number of teeth.

Couple Catches Neighbor in Attic: ‘He Was Waiting for the Creep Show’

Advantages of diamond drilling brick walls

Many are interested in the cost of brick drilling. The method is used in everyday life, during the construction and reconstruction of buildings. Private persons apply for the service when you need to improve the apartment: install sockets or change the wiring. On construction sites, diamond drilling is used when it is necessary to organize the ventilation system, lay the pipes of the water and gas supply, heating and sewage system, install fences or railings.

We perform the entire range of services: we make holes in concrete, reinforced concrete, brick and other materials, install pipes, change plumbing devices.

Increasing the length of the cut during drilling holes at an angle

Slope angle in degrees Increase the thickness of the wall by
up to 5 0
ten 2%
fifteen four%
twenty 6%
25 ten%
thirty 16%
35 22%
40 31%
45 41%
The cost of work is increased in accordance with an increase in drilling.

Drilling holes at an altitude of more than 3 meters is possible only when the customer is provided or the cost is specified separately.

The opening of 30 cm by the reinforced concrete plate is carried out by drilling holes with diamond crowns around the perimeter.

Diamond drilling holes in concrete with water collection without a vacuum cleaner. It is used where there is no finishing, but you can not pour water.

Video drilling holes in concrete with a water collection ring.

Finished hole in the concrete wall after drilling with water collection.

The remaining cores with reinforcement and plate after diamond drilling of concrete.

The minimum distance to the opposite wall with diamond drilling holes 115 cm.

It is possible to make the opening at a minimum distance to the opposite wall of 80 cm (contract cost).

Diamond drilling of the technological hole.

Forgot to make the perfume? No problem. Understanding in the foundation with diamond drill. You can make a hole in the foundation for the fiction at any time

Drilling holes for fraud with a diameter of 12 cm. In the strip foundation.

Diamond drilling holes as close as possible to the wall without water collection

Small square and rectangular holes in the floors and walls are cut out with a manual diamond tool or drilled around the perimeter.

Manufacturing of the technological hole in the ceiling

Cutting rectangular “holes” under the hatch

Rectangular ventilation hole in the ceiling

Diamond drilling holes with crowns around the perimeter is more expensive than diamond cutting with discs by an average of 20-30%. But cutting with disks of small holes (40×40, 50×50, 60×60, 70×70) is possible only in walls up to 24 cm with access on both sides. In the photo, a rectangular hole of 24 cm. monolithic wall size 60×70 cm.

Below photography of the manufacturing of a window opening by diamond drilling around the perimeter in a monolithic wall 30 cm. Holes drill over each other.

Drilling a hole in the photographs

At a distance of 32-42 cm from the center of the future hole, a hole for an anchor (or a through hole for a hairpin) is drilled, a fastener bolt is mounted in it.

We fasten the bed under a given hole. You can start drilling a hole.

We drill a hole, water under pressure is supplied from the tank.

drilling, passage, holes, walls, choose, drill

Finished hole and anchor in the wall (or a through hole under the hairpin).

ATTENTION! We have no other sites, But on many sites, the theme of which are: redevelopment of apartments, diamond cutting, strengthening openings, cutting concrete and drilling holes. Pictures posted by the company Slop Service, as well as information from the Slom-Servis website.ru.

Drilling holes

Drilling holes. from the company “Home Master” will pass for you comfortably, everyday and for reasonable money. Our master will come at a convenient time and place for you, make diagnostics, declare the exact cost of upcoming work and begin after your consent. After the end of work, you will receive an official agreement with a guarantee and a good mood for the whole day!

Popular services

Type of work cost the service order a service
Drilling a socket in concrete 490 Make a request
Drilling a socket in brick 390 Make a request
Drilling a socket in drywall 390 Make a request
Holes drill up to 50 mm 190 Make a request
Flood drilling from 50 to 100 mm 250 Make a request
Holes drill from 100 to 150 mm 300 Make a request
Holes drill from 150 to 200 mm 350 Make a request

Drilling tiles

Tiles. very fragile material. Incorrect movement. and it can just split. To drill tiles correctly, you need to follow simple rules. First of all, you need to choose special drills that have attacks from carblood. This will reduce the load on the work surface and facilitate the process of drilling.

The point where you need to make a hole, you need to outline in advance. This is done with a tap or marker. This point will guarantee that the drill will not slip. The mark is made on the outer side of the tile.

Sometimes you need to drill a tile that is already glued to the surface. In this case, you can use glass drill. There are no special secrets when drilling tiles. The main thing is not to make too much effort, otherwise the tile will crack. The better the drill, the easier the process of work goes.

Holes in concrete may be needed for a variety of purposes. The need for them may arise during the usual repair. For example, holes in the concrete wall are required when installing the toilet and other plumbing, to install shelves and sliding doors. There are a lot of examples when you need to use a drill to work with this material. Concrete has its own special properties, therefore, work with it is also carried out according to certain rules.

How to drill concrete? For this purpose, you need to purchase a drill with winning tips.

It must be remembered that the drill is used in working with concrete only to drill holes of small diameter (up to 12-13 mm). If you need to make a larger hole, then it is better to use a peorator.

When drilling concrete, the most frequent problems are breakdown of drills and their jamming. The drills can also be clogged, so they must be regularly cleaned and sharpened.

Request a call

Leave the phone and we will discuss your personal discount.

The Privacy Policy “Home Master” is valid for personal data provided by the company’s clients to provide various kinds of services.

The “home master” reserves the right to amend and additions to the current provisions of the Privacy Policy, while these changes and additions will have an advantage over the current provisions of the policy. We pay attention to the “home master” services may contain links to third parties with their own provisions of the Private Information Protection Policy. In such cases, the “home master” is not responsible for and compliance with the provisions of the Privacy Policy of any third.party company. Providing the “home master” of his personal data, the client gives full consent to their processing in the methods provided for by the current provisions of the company’s confidentiality policy.

The procedure for collecting, storing and destroying personal data

“Home Master” collects personal data only with the consent of the User and exclusively to provide the client with a service or service requiring private information: purchase in an online store, participation in promotions, warranty and service. To prevent the leakage of personal data of the client, “Home Master” uses a full range of information security measures (technical and organizational).

The maximum storage period of personal data of the client is 75 years from the date of receipt of private information by the company. In other cases, the company stores the personal data of the client until the termination of its activities.

Basics of Drill Selection. Haas University

Destruction, depersonalization or blocking of personal data or their part of the client is carried out to exclude the possibility of further processing of this information.

“Home Master” collects personal data of the client in the following categories:

  • access time and IP address;
  • sources of transition to the Internet resource of the company;
  • Internet pages that the user visited;
  • Views of advertising banners;
  • other technical information provided by the user browser;
  • client phone number (in case of call to the numbers specified on the company’s website).

When making an order on the SK-Service1 website.Ru, “Home Master” collects personal information of the client necessary for the authentication of the user/personalization of services/delivery of the order/feedback with the client:

  • information on agreements/agreements between the client and the company;
  • Information about requests and appeals sent to the company;
  • data on goods purchased by the client and the services that the client used;
  • Payments made and other financial information provided for by law

The objects of processing personal data of customers “Home Master”:

  • sale of products and the provision of other services to the client;
  • Accounting for client wishes (when developing a new product or service);
  • Feedback with the client.

“Home Master” does not provide personal data of customers to third parties, with the exception of cases:

  • obtaining the user’s direct consent to the transfer of his personal data to a third party;
  • at the request of law enforcement agencies in accordance with applicable law;
  • Figure or acquisition of the company.

Using the “home master” of cookies and spot markers

Cooks files make it possible to collect the following customer information: IP address/operating system/type of browser/address of linking sites. This is necessary to improve the services provided to the company to the company. Point markers serve to graphically reflect on the website of impersonal information about users (visitors/views on the site). At his request, the client at any time can prevent tracking his actions by disabled cookies.

Drilling holes in the concrete and brick wall

A brick wall can easily be drilled with a drill-shuruster drill with a winning drill. The main thing is to drill at small speeds from 200 to 400, turning on the shock mode and pressing the tool handle. It is necessary to ensure that the drill does not overheat, temporarily stop drilling and let the equipment cool down.

For the construction of modern residential buildings, concrete of high strength is used, only the peorator will cope with this material. In the houses of old buildings, a brick wall, which will easily take a drill shurupert.

For drilling a more solid surface and deep holes, the workflow is divided into several approaches. To get started, use a drill 20 cm long, which makes a hole 15 cm deep. Further, a drill, designed to a depth of 35 cm, goes into business. And finish drilling with a 50 cm drill. For such work, peorators are mainly used, but some drills are also designed for high loads, but not in constant mode. You need to understand that intensive work with too hard surfaces will have a bad effect on the tool.

How to determine the presence of an electric wire in the wall?

Before starting work, it should be determined that there are no electric wires or other cables at the point selected for drilling. In order not to get into the wire, you should make sure that there are switches and outlets nearby. You can also verify this with the help of a screwdriver by giving a hole in the wall. Usually the wiring stretches to a depth of not more than 10 mm.

To accurately determine the presence of the wire, special devices are used. Such detectors are able to show the presence of wiring and reinforcement in the concrete wall.