Dump for the Neva power tiller with his hands

Homemade plow

For power tillers among the attachments there are plows: horse plow for plowing, reverse plow for loosening, dipping and others. Recently began to gain popularity plow Zykov, drawings, dimensions of which can be found only on specialized resources.

The main feature that distinguishes it from mass-produced plows are carefully calculated angles of mouldboard for intensive mixing of soil. If you compare it with conventional models, you can see that the skimmer on the model Zykov is located in front at a greater distance, so the angle of lift passes on an arc.

The attachment of the plow to the power harvester is vertical. There is an adjustment of the outreach of the blade. Fastening is done with a bolted connection. Blueprints for a plow for a mini-tractor with their own hands are different from those designed for a power tiller.

With the onset of winter, private homeowners are faced with the problem of clearing snow from areas. The issue of acquiring specialized equipment that can cope with snowdrifts in the yards is actualized. Many have tractors that can be equipped to clear snow, leaves, and debris. For such purposes, power tillers with a mouldboard are suitable.

You can buy ready-made or, after reading the necessary information. to make a drawing and design a self-made blade on a single-axle tractor by yourself.

Cleaning with a snow blower

The use of a snowplow brush is considered appropriate when it is necessary to remove snow that is not caked, loose, and not more than a few centimeters thick. This is delicate snow shoveling, when you need to be as gentle as possible on the surface where the snow lies. For example, for cleaning paving tiles or asphalt. You can also use the brush as a final tool after cleaning with another tool.

The snow brush on the motorblower consists of a stiff brush head on a rotating shaft. The width of the brush is usually less than 1 meter. The brush mechanism is designed so that it can turn to one side or the other by 15-20 cm.

You may be interested in attachments for your power tiller with your own hands.

Read more about Neva power tiller attachments on this page.

Features of making a snowplow

Let’s consider another variant of making a shovel, which is not too different from the previous one. For the blade itself you will need a 3 millimeter steel sheet, and for the columns, which provide additional rigidity, you need to take thicker steel. In the stands you need to make holes to attach the shovel to the boom. It is very important to provide vertical positioning of self-made equipment in relation to the front of the power unit.

How to make a homemade moldboard (shovel) for a single-axle tractor. masters with their own hands

You can, of course, buy such equipment in specialized stores, but often the owners of small agricultural machinery prefer to make it with their own hands. There is a lot of different information and drawings on the Internet on this subject. It allows you not only to make equipment with the necessary parameters, but also to save money significantly.

Modification options

The “mounted snow blower” modification will come in handy for anyone who lives in his house. With its help, you can turn an eternally idle single-axle tractor in winter into a functional technique by attaching a blade for snow removal. In this case the variability of the nozzle is amazing. you can use special brushes to clean the passages from the snow, to attach a rotary nozzle, which will collect sediment in a special tank. It is worth watching the following video to facilitate the process of creating the attachment:

How to make the moldboard on a single axle tractor with your own hands

When making the attachment yourself, you must first carefully study its device. Presented photos, drawings of the blade on a single axle tractor with their own hands give only a visual idea of the design. It is optimal to first consider the snowplow device in reality. To do this, you can visit a retail outlet or ask to measure the blade from a familiar equipment owner. When there is no such an opportunity, you need to be prepared for the fact that during the work there may be errors that will have to be corrected.

Blueprints for a power tiller with their own hands

You can find a lot of schemes on the Internet or in thematic literature, but they are all practically similar to each other. This is due to the simple design of the shovel. Nothing unnecessary to invent here. For example, drawings of the blade for the “Neva” power tiller with your own hands will be similar, as for “Zubr”, “Zirka”. Only the design of the drawbar may vary slightly.

The drawing will help to make a shovel with a hydraulic hoist In the absence of hydraulics, the hoist is made lever-arm, for example, from a spring

Attaching the homemade snow blade to the tiller

Usually the weight of the moldboard does not exceed 20 kg. It can be attached to any single-axle tractor. Depending on the model of the unit, the connection of the attachment manufacturer provides for the front or rear. In the second version, the steering column of the power tiller has the ability to rotate by 180 o.

To connect the attached equipment, each machine is equipped with a hitch. It can be adjustable and not adjustable horizontally. The hitch also differs in configuration for each brand of power tiller. Examples of the most common models are shown below

Each manufacturer of power tillers in the manual describes the nuances of the installation of attachments. Recommendations are worth following.

How to make a mouldboard for a power tiller from a barrel

An old metal barrel is a good material for a shovel. However, the thickness of the metal should be at least 2 mm, and better. 3 mm. Thin tinplate from the load will simply bend. To get the billet of the desired oval, the barrel is cut with an angle grinder along the length into three equal segments.

The next step is to measure the length of the workpiece, which will determine the width of the shovel. If the barrel was about 1 m high, that should be enough. When a low container is available, the length of a single billet is not enough. Cut segments are welded together. The blanks are overlapped, and the joints are welded on both sides. To strengthen the seam, you can drill holes and put rivets.

If the segments cut from the barrel are small, they are welded together to obtain the desired shovel width

To assemble their own hands blade for a motorized block from a barrel cleaned the snow well and did not scratch the sidewalk, the shovel is equipped with a knife. In its lower part, using rivets or bolts, fix a metal shovel bar that is at least 5 mm thick along its edge. In addition, they drill holes every 100 mm for bolts to fix the conveyor belt. The rubber pad will not let the metal tire leave scratches on the paving slabs or asphalt.

The next step is to make the frame of the trailed device and the blade pivot. First locate the center of the shovel from the height of the shovel. At this point, a piece of 40×40 mm section profile tube is welded along its full length. In the center of the lintel, weld a semicircle cut with an angle grinder from metal 8 mm thick. Three holes are drilled in the plate: one in the center and two at an offset, so that the bucket turns sideways by 30 °.

From a profile tube of similar cross section weld the frame of the trailed device itself. Bracket turns out in the form of a letter “G”. One side is connected to the power tiller and the other side is connected to the turning adjusting unit. To make a homemade shovel for a single-axle tractor for snow removal it is possible to adjust the height, adjust the adjusting screw lever. One side of it is attached to the L-shaped bracket, and the other is entered into the hole in the profile tube of the trailed attachment.

Makeshift dozer blade

Those owners, who have no desire to produce a shovel, can easily buy it in a store, but due to the high cost of such units, more and more often the owners of private cottages and plots are interested in how to make a shovel on a single-axle tractor with their own hands. Besides, there is a lot of information and drawings on this topic on the Internet. Such possibilities allow not only to save money, but also to make the machine of necessary parameters.

Dumpers for agricultural machinery (power tillers, tractors, ATVs, etc.). п. ) make the snow removal process much easier. This is especially noticeable in the case of large piles. Any snowblower “gadget” for machinery consists of three elements: the working body, which contacts the snow, the mechanism for adjusting the angle of rotation, and the unit of attachment to the machinery.

Although factory models have many different types of designs for any agricultural device, the self-assembly of a snowplow is uncomplicated, and can save a lot of money.

With the help of a homemade machine, you can not only engage in snow removal during the winter, but also to remove debris, level the area and other necessary functions.

Leveling the Soil by Using Power Tiller in Paddy Field First Time/ Power Tiller Video 2021/Land

It does not matter what design is used by the owner. factory or the blade with their own hands. In any case, it will have three positions:

Before starting snow clearing work, the shovel blade should be set in the right position, based on three possible. Once the proper position has been determined and established, it is secured with metal cotter pins. The width of the snow throwing area, as a rule, consists of one meter, but provided the thickness of steel used is 3-4 millimeters. Some factory models allow you to throw more snow. This is because industrial samples, as a rule, are made of high quality steel.