Gas Trimmer Does Not Work Shutdown Button

In general, such a conversation should start with the fact that after buying a garden gasoline tool it would be better to first familiarize yourself with the instructions attached to it. Then many problems could have been avoided. But since this happened the gas trimmer does not start, then we must look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start with the example of the Elitech T750 model, as well as describe general recommendations for the operation of such a tool.

Start with the banal! We will figure out how to properly start a gas trimmer. It may be that the reason lies precisely here.

First you need to bring the red toggle switch on the trimmer bar to position "I". This means turning on the power.

Gas Trimmer Does Not Work Shutdown Button

Then you need to switch the fuel supply lever on the carburetor and use the “suction” button of fuel (similar to a pipette, located on the carburetor). This is necessary to supply gasoline to the engine. Return the fuel supply lever to its original position. Finally, pull the starter handle toward you sharply. The trimmer should work. Try several times if the first time fails. If after such manipulations the situation has not changed and the gas trimmer does not start, then you should first examine it yourself before leading to the service center. There are two main reasons why a garden trimmer will not start:

  1. Violation of the power circuit.
  2. There is no fuel.
  • Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. It is done like this:
  • First of all, we must take care of security measures, make sure that the trimmer is turned off. We bring the above toggle switch to the "STOP" position.
  • Then remove the rubber protection from the plug and the wiring terminal. Using a special candle key, we unscrew the spark plug and replace it.
  • After that, we assemble the device and carry out the procedure for trimming the trimmer described above.

The second reason the garden tool doesn’t work is because the fuel has run out. On the Elinech T750, a fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and fill it with gasoline (the most optimal option is the AI-92, it is inexpensive and does not clog the carburetor like the AI-76). Do not forget to add special engine oil to the tank, just 50 grams per gas tank is enough, without it the motor will begin to “sneeze” and will quickly become worthless. After we close the tank with a cap, wipe the surface of the trimmer and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.

If the gas trimmer does not start as before, then it makes sense to return it for repair. And the reason for this decision is simple – if you do not have the appropriate skills, repairing the equipment is almost impossible.

In order for the tool to serve as long as possible and there are no such malfunctions, you should, first of all, familiarize yourself with the instruction manual for the trimmer. Also, pay special attention to the operating time of the engine at the trimmer – take a short break every 15 minutes of operation and, finally, properly care for the tool, wipe it after work, lubricate it with graphite grease. Observing such simple rules, you can significantly increase the life of the tool and it is quite possible that you do not have to look for reasons why the gas trimmer will not start.

Video: Gas Trimmer Does Not Work Shutdown Button


36,283 total views, 24 views today

Different methods are used to control weeds, but one of the most effective is to mow the grass with a mower. Motorized devices are divided into gasoline and electric. By conducting a comparative analysis, the benefits are outweighed in gasoline trimmers. This technique will be discussed in the article.

The device and types of trimmer gasoline

The trimmer is designed to cut weed, depending on the type can be used in the private sector and utilities.

The design of the lawn mowers consists of the following elements:

Engine (two or four stroke on gasoline);

Solid or collapsible hose (straight or curved shape);

Control knobs (like a bicycle handlebar or a D-shape);

The head on which the fishing line is held;

Gas trimmers are of three types, the difference of which is in the type of engine, power and variety of the cutting part.

Household lawn mowers, as a rule, have a compact size, low-power engine. Many models are equipped with a folding hose, which simplifies the transportation of tools in vehicles. The trimmer copes well with its task in areas up to 20 acres.

Semi-professional equipment is used to ennoble large households with a garden and a garden. The ideal form of lawn mowing, due to the combination of compactness and good power, sufficient for processing large areas.

Professional models are used in large or industrial enterprises for the treatment of courtyards, parks and territories. The engines on these trimmers are powerful, the dimensions are quite voluminous, and a blade is used as a cutting element.

Principle of operation

Trimmer It functions due to the presence of an engine that transmits rotational movements through the shaft to the working head. This ensures the rotation of the cutting part, which is installed a few centimeters from the ground. It’s easy to control the device; this is facilitated by a convenient handle. The weight of the lawn mowers is redirected to the torso of the person controlling the equipment. Trimmer kit includes straps that hold the structure on the shoulders of the operator. An important point is the use of a protective casing, which holds flying debris and debris.

How to use a lawn mow

The trimmer is refueled before mowing, after which all elements are checked. If the fishing line is "eaten up", it is worth wrapping 2-2.5 meters of a new cutter on the head. The length of the winding depends on the volume of the drum and the thickness of the fishing line.

Before starting the lawn mowers, you should walk around the territory in order to clean stones, metal and glass. During operation, they fly off and may injure the skin. The presence of a casing on the hose is also checked.

Mowing with a trimmer is intermittent to prevent the engine from overheating. For safety reasons, overalls and glasses should be worn during operation.

The best models for domestic use:

Stihl FS 38 (about 8,000 rubles);

Huter GGT-2500S (6 150 rub.);

Makita EBH341U (10 500 rub.);

Solo 154 (13,890 rubles).

Popular questions

How to extend the life of the trimmer?

After each mowing, you should wash the tool, clean the head from dirt and dust. Refuel the lawnmow with high-quality fuel (at least 92 grades). When choosing oil, give preference to the types used for high-speed technology.

Need to fill the tank with fuel to the eyeballs?

Manufacturers do not recommend leaving fuel after mowing in the tank. Therefore, at first it is worth assessing the scale of work and dilute the oil and gasoline in the right amount. If the fuel does not work out, you can drain it until the next time. It is important to consider that the mixture retains its properties for 2 weeks.

What types of trimmers are repairable?

Household models most often produce their modest resource, after which they are written off. In some cases, you can replace the cap of the head, which is subject to abrasion from constant friction with stones and debris.

Semi-professional and professional models can be repaired than to extend the service life of the equipment. However, when buying, you need to consider that the repair of powerful equipment always costs an order of magnitude more expensive.

What is trimmer maintenance?

After work, the tool is cleaned every time. The foam rubber filter needs to be moistened with oil. If the lawn mower is used frequently, then it becomes necessary to control the fuel filter.

Due to vibrations during operation, weakening of the connecting elements occurs. Therefore, the nuts and screws should be tightened periodically. When replacing the cutting part, it is recommended to use only the line or blade parameters specified by the manufacturer.