Gasoline does not flow into the chainsaw reason

Gasoline flows from the chainsaw

If gasoline drops periodically appear on the body of the chainsaw, then it is necessary to check the tightness of the fuel tank. Over time, it may dry out. Or the gasket “hardened” and it can no longer perform its direct function.

If full-fledged gasoline streams appear, then there is a high probability that you will have to change the burst hose connecting the carburetor and the fuel tank.

gasoline, does, flow, chainsaw, reason

Why gasoline does not flow in the chainsaw?

Carburetor needle. On cheap chainsaws, the needle in the carburetor often sticks, which prevents fuel from flowing. Sometimes it is enough just to move the needle and insert it correctly.

Oil seals. Chinese and even branded chainsaws may have poor-quality oil seals with poor tightness. Fuel stops flowing when the fuel mixture begins to squeeze out through the oil seals. Gasoline leakage is quite possible through oil seals.

Troubleshooting muffler problems

If at low speeds the engine of the chainsaw works normally, but at high speeds it starts to stall and smoke, the problem may be hidden in the muffler.

To check the quality of its work, you should do:

  • dismantling (with the obligatory closing of the outlet);
  • disassembly (if the muffler is collapsible);
  • cleaning from carbon deposits using special detergents or dry method;
  • drying (using a hair dryer);
  • reassembly and assembly.

Dry cleaning without respiratory protection is not recommended. The carcinogens present in the soot will be released into the surrounding atmosphere as dust, which is extremely hazardous to health if inhaled.

To prevent clogging of the muffler during the operation of the chainsaw, you should carefully monitor the composition of the fuel mixture and the quality of its components.

Why does the chainsaw smoke

Most often, excessive smoke appears when excessive oil is added to the fuel mixture, which does not have time to completely burn out. You should also check if the carburetor settings are out of order.

Popular faults and DIY chainsaw repair

A chainsaw is a simple device that, with proper care, can last for a long time. At the same time, the saw is a tool subject to various loads and, therefore, breakages still occur. You will learn about what caused a certain malfunction and how to fix it from this article.

How to check the fuel filter and replace

To check the current state of the fuel filter, you must perform the following steps:

  • Remove the fuel hose from the carburetor fitting and direct it to a working container.
  • Press several times on the so-called “swap”.

If the gasoline comes out unevenly and with jerks, then it’s time to put in a new filter element. This is done quite simply:

  • The fuel tank cap is unscrewed.
  • Using tweezers or any other device, the filter itself is removed.
  • Having disconnected the old filter, you must put a new one and lower it into the fuel tank.

The main malfunctions of chainsaws and their do-it-yourself repair

Chainsaw is a worthy substitute for hand saws and axes. Why doesn’t gasoline come from the chainsaw tank c. Now this tool is available in almost every household. it is indispensable for arranging a personal plot, construction and repair work. For summer and winter work, you need to buy gasoline for a chainsaw and then dilute it. Extensive use and improper care of the inventory can lead to early failure of it. Air stops flowing into the carburetor, they wonder why it does not come in gasoline. But the owner of a chainsaw does not have to go to the workshop right away. many of the defects that can happen to her during use can be completely removed without the help of others.

Consequently, the carburetor is directly involved in the preparation of the fuel-air mixture, the filter cleans the air from dust, the ignition unit and the spark plug create a spark, and the gasoline contains grease.

That is why it is necessary to search for the causes of this kind of breakdown in a sequential order, starting directly from the simple ones and gradually moving on to the complex ones. And this is an important factor in the correct repair, since the person who, without thinking, begins to deal with the analysis of the carburetor, brings it to risk. Since this kind of unit must be repaired or adjusted directly in special workshops (read about adjusting the carburetor).

    An important fact is that for the trouble-free operation of the tool, it is necessary to be quite careful about the fuel itself. Since if this kind of mixture is not prepared correctly, then most chainsaws will simply not start. Consequently, not every owner will guess to look for the cause of the breakdown in the fuel. That is why, in order for your tool to always work correctly, you need to use exclusively high-quality gasoline for the mixture.

DIY chainsaw repair: fuel supply system

If the fuel mixture does not flow into the cylinder, but the spark plug is working properly, this may mean that:

To clean this unit, remove the fuel hose and check the jet. In what proportion to mix gasoline with chainsaw oil. The heart of any chainsaw is a two-stroke internal combustion engine. If it is weak, the filter must be removed through the filler hole of the fuel tank and cleaned or replaced in case of complete wear.

Troubleshooting muffler problems

If at low speeds the engine of the chainsaw works normally, but at high speeds it starts to stall and smoke, the problem may be hidden in the muffler.

To check the quality of its work, you should do:

  • dismantling (with the obligatory closing of the outlet);
  • disassembly (if the muffler is collapsible);
  • cleaning from carbon deposits using special detergents or dry method;
  • drying (using a hair dryer);
  • reassembly and assembly.

Dry cleaning without respiratory protection is not recommended. And I missed the carburetor. Gasoline-oil chainsaw c. Husqvarna chainsaw does not supply gasoline Watch the video so that users do not climb into the carburetor the chainsaw does not enter the cylinder. Often, owners of chainsaws think about why the chainsaw shoots at the carburetor, or why gasoline is not supplied to the chainsaw carburetor? The carcinogens present in the soot will be released into the surrounding atmosphere as dust, which is extremely hazardous to health if inhaled.

Primer bulb not working on chainsaw

this is a signal about the presence of bad oil in the engine lubrication system, incorrect carburetor settings, or an incorrectly prepared fuel consistency.

If the spark plug is splashed with fuel, wipe it thoroughly after removing it. You should also clean the fuel supply system. A chainsaw is also needed in construction, as a result, more fuel enters the carburetor. Further, accordingly, fuel does not enter the chainsaws. The carburetor is not. To do this, it overlaps, after which the starter is cut in. A carbon-covered candle must be carefully cleaned with an awl and emery.

When checking the candles, attention should be paid to the distance between the electrodes (the usual gap is 0.5-0.65 mm), as well as the condition of the gasket and the presence of a spark. A warped or worn gasket will have to be replaced, and the spark can be checked by putting on the ignition cable, connecting the cylinder and the spark plug nut and starting the starter.

If the discharge does not occur, the plug must be replaced. In this case, if a spark does not occur with the newest candle, it means a discrepancy in the connection with the high-voltage wire or in it itself.

Characteristics and possible causes of breakdown. Do-it-yourself troubleshooting

Chainsaws are fairly reliable and uncomplicated designs. Therefore, if you properly care for them and handle them based on the manufacturer’s recommendations, then they fail well, very rarely and various kinds of breakdowns are quickly eliminated. But if you are faced with this situation and want to personally repair your tool without resorting to the help of professionals, then delve into the information provided below.

In fact, it is unambiguously and precisely impossible to determine the reason why the instrument does not start or stalls when you press the gas, since there are a lot of factors affecting this. But do not forget that, starting from the fact that the chainsaw is equipped with a simple two-stroke engine, conditions such as lubrication, fuel, spark and air are important for its effective performance.

Chainsaw fuel tank

Starting the engine: checking the candles

If the chainsaw does not start, the first thing to do is to check for the presence of a fuel consistency in the tank. By the way, it needs to be prepared in the proportions indicated by the motor manufacturer, otherwise the tool simply will not start.

After making sure that the fuel mixture is correct and available, the ignition system should be checked. As a result, more fuel enters the carburetor, the chainsaw carburetor will help. To do this, you need to look at the spark plug.

Husqvarna 41 (Poulan, Husqvarna 51,55) Fuel Starvation and possible reasons.

Her condition can say a lot:

indicates that the fuel mixture does not enter the carburetor, and means that there is a problem with the ignition;

is the result of an excess of fuel consistency, which lies either in a violation of the method for starting the engine, or in an incorrect adjustment of the carburetor;