Gasoline gasoline stihl stalls at idle. Does not drop in momentum

trimmer for stihl grass does not work fuel pumping

Often, with the onset of spring, most owners of benzos complain about the inability to launch the motor of this grass.shocked tool. With what it can be connected? So that the trimmer for grass in the spring after winter storage is well started, you must learn to care for it correctly. How to properly store the lawn mower in winter is described in detail at the very end of the material. Now we will figure out why it is impossible to start the tool engine after winter.

One of the main reasons that after winter the lawn mower is not started. stagnation of fuel in a gas tank. If you do not drain the fuel from the tank, and leave the tool to store for a long time, then it will naturally be impossible to start the lawn mower. The properties of a mixture of gasoline with oil fall, so as a fact we get a tool malfunction. Even if the fuel mixture has remained in the trimmer last year, it is recommended to drain it, and pour freshly prepared. After that, start the tool.

Another cause may be a malfunction of the air damper. When closing it manually, the valve itself may not work, so you start the lawn mower with a completely open air damper. In this case, the tool will not start the cold, as there is a large air leak. The video below tells why a trimmer does not start for grass for cold.

In addition to these reasons for the impossibility of starting the gas mowing engine, there are others, which are also important to mention:

  • Disciplings of the Electrodes of the candle. before starting the trimmer for the grass after winter, you should twist the spark plug, inspect it, clean, dry and set the gap
  • Damage to the high.voltage wire. During the storage of the tool, the high.voltage wire could crack, damage or could gnaw the mice. Make sure the integrity of the armored pipeline if the trimmer for the grass does not start after winter
  • Oxidation of wire contacts. This usually happens if the tool is stored in a room with high humidity
  • Check the serviceability of the ignition coil. During the winter, this detail could fail, and cause a difficult to launch the tool
  • Carburetor adjustment. it is recommended to configure the carburetor after the winter. To implement this, the tool should start, therefore, if it is impossible to start, it is recommended to pour 20 grams of fuel mixture into the candle hole, and launch the motor
  • To perform all the above actions, since during a long.term storage the hole of the saapoon, filters, as well as corrosion on the walls of the exhaust system could form

Diagnose the tool, and only after that resort to a more serious repair. cleaning the carburetor.

STIHL chainsaw stalls. does not develop momentum

All STIHL chainsaw systems function well, ensuring the launch of the mechanism. But sometimes, with confident work of idle, the saw does not gain revolutions at the load, interruptions begin in the motor. This means that there may be serious reasons requiring repair: to unbalance the carburetor screws, the end of the engine resource, breakdown of the candle or ignition coil, wear of the piston group.

But, most often, the engine does not develop turns, or may stall, when the check valve is out of order, a vacuum is created, which causes malfunctions. To repair the valve quite time.consuming, so it is better and faster to replace the oil tank cover, its cost is quite affordable.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

Chainsaw “bog” what to look for and how to fix

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing redesigned gases and pairs (after burning fuel);
  • replacement of the spring more weak on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

  • impressive of previously adjusted valves;
  • first the wrong settings of the valve mechanism;
  • clogging with deposits of the fuel supply valve;
  • the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

Main reasons

The following reasons are possible why the lawn mower or trimmer for grass stalls when trying to re.start and continue the interrupted work:

  • malfunctions in the engine;
  • refusal to supply gasoline and oil;
  • damage to pipelines (capillaries, hoses, pipes);
  • malfunctions in the ignition system.

General description of problems with a scythe or trimmer is not enough here. Clear and immediate repair, high.quality maintenance is impossible without specifying the identified cause.

With gazeaming

You click on gas. and the trimmer for the grass stops working, does not develop momentum. The following alleged reasons are possible:

  • The tuning of the carburetor was lost, which appears with an increasing load on the drive itself. after its long downtime or when working in extreme conditions;
  • The fuel valve is clogged with deposits;
  • The carburetor cable is weakened and sag;
  • Excessively stretched, possibly torn off the fuel supply hose;
  • The check valve (sapun) clogged with deposits. fuel does not enter the tank with fuel.

Important! Problems in the carburetor itself give themselves out the vibration of the lawn mower.

With an increase in speed

If the lawn mower (or a trimmer for grass) has stalled when the engine speed is added, check the device according to the following signs:

  • clogging or sticking a valve built into the gas tank cover;
  • valve adjustment violation;
  • A failure in the work of pistons and cylinders. from vibration during the work of a braid for grass or a trimmer for grass, random blows directly in the session of the mowing of grass;
  • violation of the supply of fuel mixture;
  • excess air pumping into the motor;
  • cracking of the fuel intake hose, weakening its compounds.

When the fuel.heating mixture is served with the right portions to the engine in a timely manner. it burns the amount that has managed to enter from the moment of the last gallpling, and he stalls again.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The reasons here may be as follows:

  • clogging, violation of carburetor adjustment;
  • Initially incorrect configuration of the valve mechanism of the carburetor;
  • air filter clogging;
  • reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
  • clogging the throttle;
  • penetration of excess air into the fuel system;
  • The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately after the start is due to the following reasons:

  • impressive of previously adjusted valves;
  • Initially incorrect setting of the valve mechanism;
  • clogging with fuel supply valve;
  • the hose is worn or poorly attached.

Due to the violated fuel injection algorithm, a lawn mower or a trimmer for grass is greatly vibrated in work.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls. The reason may be as follows:

  • boiling gasoline;
  • The ignition wire was damaged (poor insulation);
  • The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

When opening an air damper

A lawn mower or a trimmer for grass stalls when raising the damper for the following reasons:

Ways to eliminate breakdowns

The following works are possible by carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing spent gases and pairs (after fuel burning);
  • replacement of the spring weaker on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

Signs of unbalancing

Carburetor debugging is necessarily carried out in the manufacture of the device. As a rule, the owners will learn about the need to adjust the fuel supply with their own hands only after quite serious breakdowns, in the process of correcting which, the module was removed and, for example, cleaned.

Signs of failure in the settings are the following:

  • starts up, but immediately stalls the engine. since the engine can only work when a certain amount of gasoline is supplied, with too “poor” fuel, that is, overlapping the supply channel, the motor will stop;
  • too much fuel consumption, many exhaust gases. the result of incomplete combustion of the mixture. In this case, the fuel, on the contrary, is too much and the mixture is excessively dense.

Do.it.yourself carburetor adjustment

The setting of the module does not apply to the repair and the change of spare parts is not required. In this case, the armored complex of the carburetor of the lawn mower will not be needed.

  • L. is regulated first, as it is responsible for supplying fuel at low speeds;
  • H. he is responsible for supplying gasoline at high speeds, as well as for fuel consumption and temperature;
  • T. with it, the idle speed is debugged.

Stihl chainsaw stalling? Simple fix? Check if it’s a clogged vent.

There are options, as a rule, this is a carburetor of a Chinese lawn mower, when only one screw remains for debugging on the case. to configure idle. This does not mean that the module is configured automatically. this means that even such a type of repair as debugging will be difficult to carry out. In the photo. adjusting the carburetor of the Chinese lawn mower.

  • The module tuning is carried out only with a heated engine: for this, the device is pre.included for 10 minutes. If the mowing head rotates at idle, then they begin to debugged immediately: turn the screw T counts the clock until the rotation stops.
  • Adjustment starts with a screw l. The screw turns to the right and to the left until it finds such a position in which the idle speed does not become maximum.
  • Then the screw is turned on ¼ turn against the watch. This will be his working position.
  • The idle stroke must be configured by turns against the sentry to increase the number of revolutions and the clock. to reduce. Its debugging consists in achieving such a regime in which a sufficient number of revolutions are performed before the rotation of the mowing head. In this case, the engine should operate steadily at different positions.
  • The position of the screw L is determined by the latter. at maximum speed the trimmer for grass should not work for more than 10 seconds. The throttle opens, the screw is closed clockwork, very slowly, until a decrease in the number of revolutions is established by ear.
  • Then also slowly the screw rotates against the sentry until the engine starts to work with failures. After which the screw is on the time, until the engine again works normally.

If there is a tanometer, and if the product is indicated in the product passport, coooreecration can be carried out more accurate, focusing not by ear, but on the testimony of the device. Adjustment of the carburetor of the lawn mower in the video is carried out by ear.

The Stihl FS 130 lawn mower is not launched. complex reasons for the refusal of the lawn mower

If the step.by.step method of searching for a malfunction did not give a result, and your braid for grass as before does not start or stalls, it is worth looking at the carburetor and the engine itself. A clogged carburetor can become one of the circumstances, the unbalanced work of the tool. Here you can distinguish three main obstacles:

  • Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a strong stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
  • Wear of the carburetor laying. Output. substitution of the failed laying;
  • Violation of density. To verify this indicator, you can use an ordinary household tonometer, replacing the pressure gauge on it with a suitable. Look for the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, it means that some part of the carburetor is faulty. Will have to find it and change the latest.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips are detected, scratches or backbone, on the piston or cylinder they should be changed. Piston rings are subject to inseparable verification. A small piston owl when swaying the connecting rod indicates that the time has come to change the rings. This function is most ideal to entrust to the specialists of the service center.

The main reasons for the gas station breakdown

Although motorcycles are a simple device, from time to time in its work, problems arise, which can only be eliminated by disassembling. The following malfunctions can be given as examples:

  • a chainsaw is not gaining momentum;
  • chainsaws stops functioning in the cut;
  • The chainsaw is started and stalling;
  • a chainsaw loses its power;
  • Basil stalls when pressed.

Most often, the malfunctions are associated with interruptions in the functioning of the motor, as well as with the problems of other systems and nodes. The correct handling of this technique is of great importance. When fulfilling all the rules for using a high probability problem lies in the most obvious. When searching for the causes of problems, it is advisable to start by checking the simplest part of the motorcycle and end the most difficult.

What to do

The power tool is operated according to the manufacturer’s instructions. Only after checking the tension of the circuit, the unit starts. At the same time, filling the tanks with combustible mixture and oil is controlled, the device is securely fixed in the hands. If, when fulfilling all the rules, the mechanism refuses to work, then the stihl chainsaw is repaired.

How to start a stihl chainsaw: Instruction

The manufacturer of the tool took all measures and developed a manual, thanks to which the mechanism is conveniently launched. The user will protect himself from injuries if he performs the proposed frequency of actions:

  • The ignition turns on, and the engine handle is placed in the lower position. The receipt of the atmosphere from the air filter is overlapped by the carburetor damper. To properly start a chainsaw, the throttle membrane must be open to enrich the combustible mixture.
  • The lever is set to the gas gas position. The starter twitches several times before the appearance of the first spark. If a flash passes, then the tool is ready to launch. The mechanism works at high speed due to a closed throttle membrane. To transfer it to the idle regulations, the gas trigger is released and the rhinestone is released. The number of revolutions is rapidly normalized.
  • At the STIHL MS unit, the standard configuration does not provide additional devices to start a chainsaw in a lightweight version.

Cooper adjustment

Before commissioning, the tool maintenance is carried out. In order for the idle adjustment to go effectively, they do prevention:

To establish the operation of the mechanism at idle, the appropriate adjusting screw is used. Its turning depends on the required setting:

  • With standard commissioning, the screw is twisted against the hand arrows until the position when it will turn tight. After that, 2 circles are made in the direction of the arrow.
  • If the saw works at low speeds, then the screw is twisted clockwise until the moment the chain movement begins. Then make half a circle in the direction against.
  • At a high frequency, the regulator is wrapped against the watch arrow until the circuit stops. After that, the rotation continues by half the turnover in the same direction.

It will not work to adjust idle work if there is an air suction into the engine through the gasket, acceleration pump, seals or for another reason.

Setting the ignition

Gasoline engines are equipped with a ignition system, with which fuel is ignited. The time of the outbreak affects the operation of the motor. With mass production in the factory conditions, the ignition of the chainsaw is not done. Tags are set on the corresponding rotating elements, which are combined during the setting. Incorrect adjustment leads to the fact that the mechanism starts and stalls.

Read also: fasteners for wires to the wall

Before adjustment, check the dryness of the candle and the performance of the ignition scheme. The voltage supply cable to the candle is brought to the cylinder with a small interval and launched a starter. In the absence of a flash, a cable is tested by a sampler. Then check the serviceability of the wire to the disconnecting button.

If the cables are without damage, then the ignition coil is checked. This is done by a special tester to call the device. In this case, the indicators on the device must coincide with the technical characteristics of the coil, which are registered in the instructions of use. If inconsistencies are revealed, then the ignition unit changes to the working device.

The coil may become unusable from vibration when the tool falls or shots, so you need to work carefully.

Replacement of cramp shaft bearings

To begin with, they measure compression, if it is not, then the reason lies in the breakdown of the piston group.

gasoline, stihl, stalls, idle, does, momentum

The required pressure in the cylinder should be 8 atm, if it is lower, then perhaps the cylinder and piston, rings, crankshaft bearings are worn out.

To find out the condition of the piston system, you need to completely disassemble the saw and remove all the main components of the mechanism:

  • dismantle the headset, remove the cover on the bus;
  • remove the tire guide and the tool chain using the key from the kit;
  • Remove the air filter, remove the spark plug;
  • In place, the candles are fastened with a piston stopper for fixing the crankshaft;
  • Remove the coupling, then it opens access to the adhesion system.

Rings with bearings are inspected, defects are detected. The replacement can be carried out independently, for which the repair skill will be required, or to take the tool to a specialized workshop. The assembly is done in the reverse order.

Hello! If you find yourself on this VEB page, then, in all, it seems, your chainsaw is stalling when pressing gas, and for you to find out why this is happening and what to do with it. What, after all, I will try to provide any help to you in this dilemma, having dismantled the more proven prerequisites for such a raki, and similarly ways to eliminate them.

In the beginning, I will immediately write for new users that some chainsaws before the start of the working day asks for a heating of the motor at idle for approximately one minute. Until the engine is heated, the saw can stall when gas is added.

What is needed if the heated chainsaw works at idle, but stalls at a load, this means that:

  • The carburetor is incorrectly configured or clogged. the most frequent case;
  • She lacks air, the consumption of which increases sharply with increasing speed. this means that the air filter is contaminated (the case is rare, because the filter pollution occurs evenly, because the user initially notices the loss of power);
  • It is not enough fuel enough, the consumption of which also grows with increasing speed. this means that the fuel filter (also an infrequent case) is contaminated;
  • And the most nasty case, if there is excessive friction between the piston and the wall of the cylinder associated with a shortage of oil in the fuel consistency. after such a chainsaw you are most likely to fly to the repair of the piston group, because clogs that prevent work are formed on the piston and walls of the cylinder saws.

Why is a Chinese lawn mower not developing momentum?

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. The lawn mower does not develop speed, why the Chinese benzotrimmer STIHL FS. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

How to fix a disk or a fishing line for a trimmer on a trimmer

The cutting mill is attached to the executive organ. The mounting location is called a gearbox. It is not difficult to cope with the task of installing a disk or coil. The principle of consolidating cutting discs on the trimmer is as follows:

  • The figured washer is originally fixed by using a hexagonal key
  • On the shaft set the disk
  • Then install the upper washer, and then tighten it by means of the fastener
  • It is necessary to rotate the nut through a special end key, which is usually equipped with each tool
  • The rotation of the nut is carried out in the direction counterclockwise
  • When rotating, it is necessary to jam the shaft with a hexagonal key

In the opposite sequence, the disk on the trimmer is removed and replaced. details on how to install a coil with a fishing line on a lawn mower is described in this material.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence of fuel hose cracks or problems with the oil seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.

How to adjust the carburetor of a trimmer for grass

On trimmers, not counting electronic engines, gasoline internal combustion engines are installed. This mechanism asks for special attention to himself, since he will either refuse to work with incorrect tuning, or will work with interruptions and power loss. In the main thing, the setting of the engine is to adjust the supply of fuel, and this is done using a carburetor of a trimmer for grass.

Clogging of the mesh filter

A mesh filter can be contaminated when dirty fuel is received through a fuel hose or an absorbing head having disadvantages. In the photo below, you can see how the unsuccessful filter and dirty look like (parts are broken by the line).

gasoline, stihl, stalls, idle, does, momentum

To eliminate the malfunction, you will need painstaking cleaning and flushing of the mesh filter. It is also recommended to blow out all the holes in the carburetor body with compressed air Trimmer for grass

Determination of the causes of the malfunction

If the trimmer engine for grass does not start or stalls immediately after starting, when overheating or during the functioning of the device, extraneous noises are heard and vibration is clearly felt, it is important to perform a visual inspection and identify a non.working node

To optimize preparatory measures before repairing, a simple diagnosis should be carried out and checked in stages:

  • the presence of fuel in the tank and lubrication in the main nodes;
  • serviceability of the spark plug and its performance;
  • the purity of the fuel and air filter motorcycles;
  • Cutting of the exhaust channel and the device’s saepun;
  • The quality of the used fuel and lubricants.

To determine the functional performance of the ignition of the lawn mower, you should determine whether the candle works by testing the appearance of a spark in contact with the body of the functional device.

The spark plug itself can be changed to a new one, after driving the candle canal, if necessary, the old element is also dried, cleaned with special devices and returned to place.

From personal experience

lawn mower or trimmer for grass

Trimmer for grass is a broader concept than a lawn mower (lawn mower), since it can also be an electric. The gasoline trimmer for grass and the lawn mower is the same thing.

Some authors assure that a trimmer for grass is a weaker tool, unlike a more powerful lawn mower, which can be used to mow shrubs. Personally, I have a tool with a maximum capacity of 1.7 kW and capable, as stated in the instructions, to mow a small shrub up to 10 mm thick. User manual is called “trimmer for gasoline grass”.

The proportion of the fuel mixture

I read somewhere that if the law mowing manual and the canister with butter indicates different proportions of the preparation of the fuel mixture, the proportion indicated in the manual should be used.

It was done for a long time. excess oil flowed out of the engine to the gas tank and the fiber was constantly formed on the candle, since the leadership indicated a proportion for a running.in engine 1:25, and on the canister. 1:50. After the transition to a proportion of 1:50, the appearance of oil fluxes stopped. The candle continued to burn, but with less intensity (the carburetor has not yet been adjusted).

Until now, some users of the benzo tool determine the fuel mixture “by eye”. If when preparing the mixture the amount of oil is underestimated, after a while an extraneous sound may appear immediately after the engine starts, gradually disappeared during heating, and the engine stop occurs with a sharp jerk. The continuation of the operation of a trimmer for grass in this mode will lead to its failure.

Clead cleaning

In the worst times of the work with a trimmer with an unresolved carburetor, the engine stopped starting after using each fuel tank. And only after cleaning the candle from the car, could you continue to work.

For cleaning the electrodes, fine sandpaper was used, and a thin stationery clip with a bent end was used to clean the space between the insulator and the case. At first, the electrodes were wiped with high dirt with a rag, then cleaned with sandpaper. After that, the candle fell into the diesel fuel and the moistened carpet was opposed by a paper clip from the surfaces of the insulator, the inside of the body and between them. Further, the candle fell several times into the diesel fuel, which then shake off it along with the pollution. Sometimes the procedure for cleaning a paper clip and washing were repeated. After that, the candle wiped dry and was ready for further operation.

Невероятно, но один бачок топливной смеси при неотрегулированном карбюраторе может израсходоваться менее, чем за 10 минут — проверено на практике, когда триммер для травы был запущен и эксплуатировался на высоких оборотах с максимальной подачей топлива (регулировочный винт был откручен намного больше нормы).

You can order seeds of vegetables and flowers, plant protection and microme-sharing products in the online store. Low and good germination on customer reviews. Mail delivery.

The lawn mower is a mobile high.performance tool for ennobleing personal plots and adjacent territories. With prolonged operation due to wear of parts or production marriage, there are malfunctions that lead to the fact that the trimmer for the grass stalls or does not start. Since this tool is a rather complicated mechanism, because the reasons why the lawn mower stalls can be several.

There are two main ways to eliminate problems: transmitting braids for grass to a specialized center or solving the issue with your own hands. The first option is suitable for those who are ready to lay out a “round” amount to restore the performance of the unit, and the second for someone who has basic locksmith skills and can independently deal with the causes of breakdowns and ways to eliminate them.

It is currently customary to classify breakdowns by which the lawn mower stalls in the following categories:

  • mechanical damage to the ICE crankcase, malfunctions of the cylinder.piston group (CPG);
  • breakage associated with the supply of fuel mixture (air filter, carburetor);
  • problems due to damage to tubes, hoses, cables or ignition circuits.

If you once got a trimmer for grass, working with gasoline, then you probably had to face the inconsistent of the inclusion of a trimmer for grass, as well as such an inconsistency as a benzotrimer

So, what to do if a trimmer for grass, working for you not for the 1st year, suddenly just stops gaining momentum, and the motor simply stalls? In this case, you and I should see a number of troubles related to stopping the work of the motor.

The motor may stall under different circumstances. The EFCO Stark 25 Benzotrimmer does not develop momentum as if I gasp for a quarter what to do. From time to time, the prerequisite of the incorrect work of the trimmer for grass working from gasoline is clogging of the air filter.

Specifically, the filter is one of the most basic circumstances according to which the work of a gasoline trimmer for grass may end.

Different garbage very often gets into it, particles of dust that also clog the filter, because it must be cleaned and washed every month, and maybe more often, everything is depending on what power the gasoline trimmer has for the grass, also how often you use this device.