Grease For The Trimmer Gear Stihl Fs 55

Consumer reviews

If you still do not understand, if you choose the Stihl FS 55 trimmer, then you should pay attention to consumer reviews. After reading them, you can understand that the design provides for the presence of a two-shoulder strap, which is better than a webbing. This way, you can distribute the weight of the equipment across your entire back, rather than focusing on one shoulder. As practice shows, even after long-term work, joint pain does not occur. Stihl fs 38 trimmer bearing lubrication Stihl fs 55 in operation. Lubrication of the flexible shaft of the STIHL FS 55 Do-it-yourself Stihl trimmer Stihl FS 38. Stihl fse60 shaft lubrication fse60 Stihl How. When using the device, the arms are very wide apart, so it becomes easier to control the trimmer, which indicates its maneuverability.

The petrol trimmer Stihl FS 55 can be adjusted to the operator’s height. The handle and belt are tuned for a very comfortable fit. Customers also like the fact that the controls are located on one handle, so you don’t have to reach for them, because everything is placed near the palm.

Additional recommendations for use

The next step is to restart the engine using a cable. With your right hand, pull out the handle until you feel the stop. Then very and sharply it is necessary to pull up the starter rope. The stihl fs 55 lawn mower is one of the most popular Stihl trimmer models in the household lawn mower class. If there is an ergo-start device, then the cable must be pulled very smoothly, while providing a constant voltage.

Do not stretch the cable all the way. If you are using the Stihl FS 55 trimmer, be sure to read the instruction manual for this equipment. From it you can learn that the next step before starting will be opening the air damper. To do this, use the drive lever.

Specifications

The Stihl FS 55 trimmer is a good solution for lawn maintenance. The motor power of this unit is 1 liter. S., normal for domestic use. In one pass, you can cut grass up to 120 mm wide. It is noteworthy that the design has a special system that allows you to care for the grass even along fences, in narrow areas and around flower beds.

Self-repair of SHTIL FS 55 lawn mowers. Replacement of gearbox bearings

Now you will learn of the release: How to change gearbox bearings; How to choose the right bearing; how.

The volume of the motor is 0.33 liters, which will be enough for half an hour of work. The trimmer kit Stihl FS 55 is supplied with a protective cover and a trimmer head. This should include the two-shoulder belt, which simplifies implementation. As for the protective casing, it acts as a reliable barrier for fishing line and knife.

Device Trimmers Stihl Fs 55

Trimmer Stihl FS 55: review, properties and

Techniques such as lawn mowers and trimmers are now not unusual in a summer resident’s arsenal. If you also want to care for your lawn in a modern way, then you should consider these units. With their help, you can mow the lawn and cut the bushes, and also remove weed thickets. In this case, the territory will look neat, like the clubs.

Of course, you can take care of the site for another, but over time, weed plants are planted everywhere, thereby drowning out useful growth. In order to simplify your gardening work, you can purchase the Stihl FS 55 trimmer, which will be discussed below.

Manual

Before starting to use the equipment is described, you need to read the instructions for its use. As for the launch, in front of it you need to enclose the device on the ground. The stops and the protective cover act as supports. At the same time, the cutting tool should not touch the ground or other objects, because when starting it will start to spin.

FS 55 lawn mowers overview

Trimmers are now also referred to as lawn mowers, and the model that was mentioned above is no exception. Do-it-yourself Stihl trimmer repair Stihl FS 38 Stihl FS 55 not gaining momentum? Come on. You will have to pay 13,490 rubles for it. It is a premium device. It can be used to care for large suburban areas and lawns. This machine mows weeds, young and old grass, shrubs and reeds.

Device Trimmers Stihl Fs 55

Specifications

The Stihl FS 55 trimmer is a good solution for lawn maintenance. The motor power of this unit is 1 liter. S., normal for domestic use. In one pass, you can cut grass up to 120 mm wide. It is noteworthy that the design has a special system that allows you to care for the grass even along fences, in narrow areas and around flower beds.

The volume of the motor is 0.33 liters, which will be enough for half an hour of work. The trimmer kit Stihl FS 55 is supplied with a protective cover and a trimmer head. This should include the two-shoulder belt, which simplifies implementation. As for the protective casing, it acts as a reliable barrier for fishing line and knife.

Additional recommendations for use

The next step is to restart the engine using a cable. With your right hand, pull out the handle until you feel the stop. Then very and sharply it is necessary to pull up the starter rope. The stihl fs 55 lawn mower is one of the most popular Stihl trimmer models in the household lawn mower class. If there is an ergo-start device, then the cable must be pulled very smoothly, while providing a constant voltage.

Do not stretch the cable all the way. If you are using the Stihl FS 55 trimmer, be sure to read the instruction manual for this equipment. From it you can learn that the next step before starting will be opening the air damper. To do this, use the drive lever.

Manual

Before starting to use the equipment is described, you need to read the instructions for its use. As for the launch, in front of it you need to enclose the device on the ground. The stops and the protective cover act as supports. At the same time, the cutting tool should not touch the ground or other objects, because when starting it will start to spin.

Device Trimmers Stihl Fs 55

Trimmer Stihl FS 55: review, properties and

Techniques such as lawn mowers and trimmers are now not unusual in a summer resident’s arsenal. If you also want to care for your lawn in a modern way, then you should consider these units. With their help, you can mow the lawn and cut the bushes, and also remove weed thickets. In this case, the territory will look neat, like the clubs.

Of course, you can take care of the site for another, but over time, weed plants are planted everywhere, thereby drowning out useful growth. In order to simplify your gardening work, you can purchase the Stihl FS 55 trimmer, which will be discussed below.

Consumer reviews

If you still do not understand, if you choose the Stihl FS 55 trimmer, then you should pay attention to consumer reviews. After reading them, you can understand that the design provides for the presence of a two-shoulder strap, which is better than a webbing. This way, you can distribute the weight of the equipment across your entire back, rather than focusing on one shoulder. As practice shows, even after long-term work, joint pain does not occur. Stihl fs 38 trimmer bearing lubrication Stihl fs 55 in operation. Lubrication of the flexible shaft of the STIHL FS 55 Do-it-yourself Stihl trimmer Stihl FS 38. Stihl fse60 shaft lubrication fse60 Stihl How. When using the device, the arms are very wide apart, so it becomes easier to control the trimmer, which indicates its maneuverability.

The petrol trimmer Stihl FS 55 can be adjusted to the operator’s height. The handle and belt are tuned for a very comfortable fit. Customers also like the fact that the controls are located on one handle, so you don’t have to reach for them, because everything is placed near the palm.

FS 55 lawn mowers overview

Trimmers are now also referred to as lawn mowers, and the model that was mentioned above is no exception. Do-it-yourself Stihl trimmer repair Stihl FS 38 Stihl FS 55 not gaining momentum? Come on. You will have to pay 13,490 rubles for it. It is a premium device. It can be used to care for large suburban areas and lawns. This machine mows weeds, young and old grass, shrubs and reeds.

It is essential to make sure that there are no unauthorized people near the Stihl FS 55 petrol trimmer. They should be no closer than 15 meters. Basically, take a stable position before starting. Next, you need to prepare the stop button for work. Stihl trimmers like fs 38, fs 45, fs 55, fs 55 trimmers motor fs 250 device It is located on the multifunction handle.

Now you can move on to fixing the throttle lever. It should be pressed and held in this position. At the same time, use the throttle lever. You need to add it in this position until the latch touches the tongue of the case. If the throttle lever is locked, then you need to lower it first, and then. Retainer. The tool lever is now ready to start.

The Stihl FS 55 trimmer, which you could read about above, has a fuel pump. You need to click on it 5 times, even if it is full. This will reduce the number of start attempts, which simplifies the process to work. Now you can close the choke by pressing the drive lever.

The air damper on a cold engine must be closed; for this, the drive lever is set to the appropriate position. The Stihl FS 55 trimmer, the instruction manual of which is presented in the kit, must be laid on the ground again. It is important to make sure that the braid is very tight. It is a device included in the Stihl FS 55 trimmer Stihl year. The tool is pressed against the ground so that it does not tip over when starting. It is important to make sure once again that the cutting tool is not in contact with anything.

What kind of lubricant should be used for the trimmer gear?

During operation, the mechanical part of the trimmer is loaded by contact forces on the teeth, resistance reactions from adhered grass (sometimes with dirt), dynamic, shock loads due to constantly changing torque. Lubricant for the trimmer gear must fully take into account these features, so the selection of the brand must be strictly individual.

The following factors are taken into account:

• Manufacturer’s brand. Each brand reasonably focuses on self-made lubricants (you can talk about cheap Chinese products later). This applies to manufacturers such as Husqvarna, Stihl, Huter, Makita, etc. The only exceptions are domestic trimmers: for example, the Caliber in the user manual does NOT indicate the brand of lubricant at all.
• The viscosity of the lubricant. As you know, all lubricating compositions are divided into three groups. high-viscosity (colloidal systems containing various additives), plastic compounds for universal use and solid lubricants that soften during operation.
• Good adhesion to the surface of gearbox parts, as a result of which the grease is NOT squeezed out into the gaps or out of the unit.
• The rate of grease consumption by the gearbox. Here you have to rely on your own experience and the recommendations of specialists, since some trimmer manufacturers, relying on their own service centers, do not give clear recommendations at all for the period of the gearbox operation between two lubrications.

Lubricant consumption also depends on the temperature at which it retains its lubricity. When the gearbox is heated to 40 ° C, it is considered that its operating conditions are satisfactory, and there is sufficient lubrication.

It is believed that there is no universal grease for the trimmer gearbox, but this is not entirely true. In fact, a suitable lubricant will be one in which the following components are present:

• Lead-free antiwear additives;
• Solid lubricants with the presence of graphite or molybdenum disulphide (the latter is preferable, since the lubricity is fully retained for a wide range of shaft speeds)
• Only mineral (inorganic!) Oils, highly refined.

These requirements are fully met by Gear Grease OREGON or Champion EP-0 lithium greases, domestic compositions Oleo-Mas, Litol.24, or Azmol 158, as well as what is recommended by the manufacturer of a particular trimmer model.

Lubricant for trimmer gear. How and how to lubricate?

Sometimes, in the midst of an intense mowing operation, your trimmer will start making an unpleasant grinding noise. This complains about the lack of lubrication of the gearbox. The most heavily loaded unit of the device. And soon on These “Warning” may follow and jamming of the drive.

How to Lubricate the Trimmer Gearbox?

In the upper part of the body, where the gear block is installed, there is a technological hole, which is plugged with a screw during trimmer operation. This screw is unscrewed, and 1.5. 2 ml of lubricant is injected into the hole using the spout on the tube. If the lubricant was purchased in a different package, then an ordinary disposable medical syringe is also suitable for this operation.

After that, the screw is reinstalled. This procedure, regardless of the user’s recommendations, should be performed every 10. 15 hours of operation of the trimmer in working mode. Other reasons for updating or replacing the gearbox lubricant are the independent performance of minor routine maintenance (for example, cleaning and flushing the gears of the gearbox before the start of the summer season), repairing the unit, preserving the trimmer for the winter, etc.

If the gear unit is disassembled, it is recommended to completely remove the remnants of the old grease from the surface of the parts, even if it does not have any traces of oxidation and contamination. And only then applies new lubricant. After applying the lubricant, it is recommended to turn the shaft several times by hand, and make sure that the lubricant is evenly distributed over all parts of the gearbox.

When lubricating, pay particular attention to the following elements:

• Flywheel: grass residues tend to stick to its surface intensively, and thickening herbal juice creates additional resistance.
• Pawl of the starter coil, which, in the process of turning on the drive, constantly contacts the grooves on the flywheel. In this case, not only mechanical wear occurs, but also mechanochemical corrosion of the “flywheel-dog” connection, since the materials in this pair are different (the flywheel is aluminum, and the dog is steel).
• Bearings, if their seals are worn out, and through them the remaining grease is squeezed out. In this case, the unit begins to vibrate intensively when loaded. This happens with Chinese-made trimmers, so it is worth thinking in the future about replacing the bearings of the assembly with a better one, for example, from the Swedish company SKF.

What kind of lubricant should be used for the trimmer gear?

During operation, the mechanical part of the trimmer is loaded by contact forces on the teeth, resistance reactions from adhered grass (sometimes with dirt), dynamic, shock loads due to constantly changing torque. Lubricant for the trimmer gear must fully take into account these features, so the selection of the brand must be strictly individual.

The following factors are taken into account:

• Manufacturer’s brand. Each brand reasonably focuses on self-made lubricants (you can talk about cheap Chinese products later). This applies to manufacturers such as Husqvarna, Stihl, Huter, Makita, etc. The only exceptions are domestic trimmers: for example, the Caliber in the user manual does NOT indicate the brand of lubricant at all.
• The viscosity of the lubricant. As you know, all lubricating compositions are divided into three groups. high-viscosity (colloidal systems containing various additives), plastic compounds for universal use and solid lubricants that soften during operation.
• Good adhesion to the surface of gearbox parts, as a result of which the grease is NOT squeezed out into the gaps or out of the unit.
• The rate of grease consumption by the gearbox. Here you have to rely on your own experience and the recommendations of specialists, since some trimmer manufacturers, relying on their own service centers, do not give clear recommendations at all for the period of the gearbox operation between two lubrications.

Lubricant consumption also depends on the temperature at which it retains its lubricity. When the gearbox is heated to 40 ° C, it is considered that its operating conditions are satisfactory, and there is sufficient lubrication.

It is believed that there is no universal grease for the trimmer gearbox, but this is not entirely true. In fact, a suitable lubricant will be one in which the following components are present:

• Lead-free antiwear additives;
• Solid lubricants with the presence of graphite or molybdenum disulphide (the latter is preferable, since the lubricity is fully retained for a wide range of shaft speeds)
• Only mineral (inorganic!) Oils, highly refined.

These requirements are fully met by Gear Grease OREGON or Champion EP-0 lithium greases, domestic compositions Oleo-Mas, Litol.24, or Azmol 158, as well as what is recommended by the manufacturer of a particular trimmer model.

Lubricant for trimmer gear. How and how to lubricate?

Sometimes, in the midst of an intense mowing operation, your trimmer will start making an unpleasant grinding noise. This complains about the lack of lubrication of the gearbox. The most heavily loaded unit of the device. And soon on These “Warning” may follow and jamming of the drive.

How to Lubricate the Trimmer Gearbox?

In the upper part of the body, where the gear block is installed, there is a technological hole, which is plugged with a screw during trimmer operation. This screw is unscrewed, and 1.5. 2 ml of lubricant is injected into the hole using the spout on the tube. If the lubricant was purchased in a different package, then an ordinary disposable medical syringe is also suitable for this operation.

After that, the screw is reinstalled. This procedure, regardless of the user’s recommendations, should be performed every 10. 15 hours of operation of the trimmer in working mode. Other reasons for updating or replacing the gearbox lubricant are the independent performance of minor routine maintenance (for example, cleaning and flushing the gears of the gearbox before the start of the summer season), repairing the unit, preserving the trimmer for the winter, etc.

If the gear unit is disassembled, it is recommended to completely remove the remnants of the old grease from the surface of the parts, even if it does not have any traces of oxidation and contamination. And only then applies new lubricant. After applying the lubricant, it is recommended to turn the shaft several times by hand, and make sure that the lubricant is evenly distributed over all parts of the gearbox.

When lubricating, pay particular attention to the following elements:

• Flywheel: grass residues tend to stick to its surface intensively, and thickening herbal juice creates additional resistance.
• Pawl of the starter coil, which, in the process of turning on the drive, constantly contacts the grooves on the flywheel. In this case, not only mechanical wear occurs, but also mechanochemical corrosion of the “flywheel-dog” connection, since the materials in this pair are different (the flywheel is aluminum, and the dog is steel).
• Bearings, if their seals are worn out, and through them the remaining grease is squeezed out. In this case, the unit begins to vibrate intensively when loaded. This happens with Chinese-made trimmers, so it is worth thinking in the future about replacing the bearings of the assembly with a better one, for example, from the Swedish company SKF.