Hammer lawmaker does not start reasons.

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

• After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
• When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
• At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
• He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

• The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
• Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
• Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
• If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate can form on a gas tank day, which is due to which the tasks with the operation of the device appear.
• Excessive swing of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
• Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
• trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
• Knives are removed from the car. some models will not work under this condition.
• Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
• From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

• low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
• The grass was wound on the shaft of the fishing/knife head;
• clogging of the air filter/muffler;
• Balance of the carburetor.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

Cycle: what mistakes of beginners lead to breakdown of the engine of the trimmer for grass and exclude its normal operation

6 common mistakes with fuel

The manufacturer in the instructions clearly indicates the brand of gasoline with an octane number, oil and their proportions.

The first three errors are that the user of motorcycles violates all or one of these requirements. The motor will most likely start and work, but its resource may decrease sharply.

A small amount of oil, like its absence, will lead to the fact that the walls of the cylinder will not grease normally, and the piston rings will scratch them, and not slide.

Excess oil will simply burn, forming soot. She will pollute everything, including the piston and cylinder.

Failure gets into the valve, blocks their work, after which the motor will not start.

Will have to disassemble and clean the carburetor, or even put a new. Of course, you can try to wash the piston and the cylinder: it may be possible to bring them into working condition, but it is better not to bring them to.

The fuel mixture must be prepared with high quality and in strict proportion. The repair of a spoiled engine is expensive, about 70% of the price for a new gasoline trimmer for grass.

For the preparation of high.quality fuel mixture, I have a special container with a factory division of divisions in a set of trimmer for grass. Gasoline is neatly poured into it to the level of 500 ml, and then the oil to the required label.

An alternative method is the preparation of a fuel mixture with filling gasoline into a calibrated container, for example, a liter canister or a plastic bottle to a label, and an oil additive with a medical syringe according to its divisions.

The dosage with a syringe is more convenient, is considered the most popular way.

I recommend filling gasoline through a funnel with a narrow neck that has a filter: a metal mesh. protection against small garbage.

The prepared mixture should be well shaken and mixed until a uniform color appears. Only after that it can be poured into the tank.

If the mixture does not blame, then it will remain in the tank, and through the carburetor will enter the combustion chamber in portions with different ratios of gasoline and oil.

Fractions of clots of oil clog a candle. The motor stops, stalls, does not start. This is the fourth mistake of beginners.

It should be borne in mind that gasoline is hazardous. The risk of fire exists. Therefore, it is necessary to fill the mixture at a safe distance from the buildings, and in the case of the strait, which often happens to eliminate the causes of a possible fire. Violation of fire fighting measures. error

After pouring the fuel into the gas tank, the latter closes with a screw plug and the lack of leaks is checked. The trimmer for the grass is raised up so that the gasoline fills the cork. There should be no subterations from under the lid or from the fuel hoses.

Lack of such a check. an error can cause a fire.

There is one technical cunning that can cause a benzotrimer motor is not started due to the cessation of fuel supply. If you look carefully at the center of the traffic jam, then a round hole is clearly visible.

We turned Motokosa. Gasoline filled the cork, but does not flow through the hole: there is a sapphone inside. He is working.

On the inside, its design is clearly visible: a valve system of plastic and rubber is built.

In the usual state, the valve is pressed to the hole and the fuel does not flow. Когда бензомотор работает, то топливная смесь расходуется через карбюратор. A vacuum is created in the tank. The vacuum opens the valve of the saapon, the pressure is restored.

You should know the two consequences of a malfunction of the sapuna:

• Constantly open hole. fuel pours out of the tank during its inclinations (excess consumption and the probability of fire).
• Contamination or sticking of the valve channel is the reason that the lawn mower does not start or stalls.

Check the soundtress is easy: you need to blow it in both directions.

All about the gas tank cover, including the repair of the saapun, is shown in the video of Bogdan Shabanov.

3 additional advice associated with limited chemical resistance of a mixture of gasoline with oil:

• Do not create an excessive fuel supply. Use freshly prepared fuel mixture. In a maximum of a couple of weeks, she will lose her useful qualities;
• Prepare as much fuel as it will go to one mowing during the day. At the end of the work, drain the rest from the gas tank and burn the last drops from the fuel canal with a neglected engine;
• It is especially dangerous to leave the mixture in the gas tank for a long time. winter. In the spring, you will make sure that the engine does not start without cleaning the carburetor (gasoline evaporated, the oil thickened and glued the valve).

In more detail, the technology for eliminating these malfunctions shows in its video video “Chinese lawn mower is not started” Sergey Lesnik. Pay attention to the fuel filter.

To adjust the work of the carburetor allows a special screw, but it is not worth it to twist it without need: the factory adjustment is accurately exhibited. It is better for novice users to contact the service center.

Cycle: why the piston may not move inside the cylinder

The flywheel of a trimmer for grass, aka Magneto’s rotor with magnets, is fixed on the shaft with a key.

This is usually a reliable connection. Under the flywheel there is a sealing oil seal that does not pass the oil from the crankcase out. But when he wears out, the craftsmen have to remove the flywheel and change the oil seal with a new.

Otherwise, the oil flies everything, including the air filter.

At the same time, it is not so easy to remove the key: people make special pullers.

When looking for information on trimmers, I came across a video of one master, who was brought into the repair of the lawn mower, where the flywheel gap was absent. Perhaps a factory marriage. Naturally, such a motor will not start.

A similar reason should also be borne in mind.

Proper care for the chainsaw

There are no unnecessary phrases in the operating instructions, everything that is proposed is aimed at the trouble.free operation of the lawn mower. Cleaning all parts after each cycle of work contributes to the light removal of not hardened residues and dirt. You need to clean only cooled nodes. This technique contributes to the quality of the air cooling of the engine and the gearbox.

For refueling, it is necessary to use fuel with oil recommended in the instructions. If you leave the combustible mixture in the fuel tank, the oil will float and dies on the damper when starting, worsening its adjustment. The mixture can give a sediment and score fuel supply in the carburetor.

When preserving equipment for the winter, make an audit, grease the gearbox and the piston system, wrap the entire saw in the oiled rags and store in a dry place.

It is impossible, dangerous for the instrument and health of the mowing, use a metal cable instead of fishing line. It cuts more efficiently, but the load on the gearbox and the engine increases. A demolished piece of wire when separating flies at the speed of a bullet. Effective mowing can lead to a speedy wear of the piston group of the engine. For greater efficiency of the mowing, it is proposed to use the profile of the “Star” fishing line.

Diagnosis of the lawn mower and elimination of causes. video

ATTENTION. If you have a question, then you can ask it in the Комментарии и мнения владельцев to the article below! Our experts will answer your question in the near future (1-2 days), subscribe to the comment to receive a notification about the answer in time!

You can also ask a question on this page, then we will prepare a detailed answer (5-7 days), which will be here!

Cleaned, dried in the hot sun, from adjusted 1 mm gap. a candle of ignition, a braid for the grass earned like a new!

The candle has a black terry fog, after cleaning it starts and immediately stalls, the candle is flooded.

My problem is that the Hyter lawn mower starts only if I remove the muffler. At the same time, the muffler is clean and I still blew it and cleared it, it is worth putting the muffler in place, the lawn mower will not start, what is with it? Thanks a lot in advance.

Recommendations for operation

The stability of the work of any motorcycle and the lack of problems with the launch of the power unit of such devices directly depend on the conditions in which the tool and quality of maintenance is used. And we are talking about the following basic rules:

• In the process, it is necessary to pay special attention to the cooling system and other elements; It is strongly recommended to timely and qualitatively clean the channels located on the hull of braids for grass and ribs of the starter;
• In the process of processing various elements, solvents, gasoline, kerosene and other effective means can be used;
• The indicated work should be carried out after completely cooled by the power unit;
• It is necessary to fully comply with all the rules specified in the relevant instructions drawn up by the developers of the described tool, which will avoid overloads in the heated engine, which in turn is the most common cause of serious breakdowns;
• All fuel remnants in the internal combustion engine should be completely drained before long breaks in operation of braids for grass; It should be borne in mind that the gasoline-oil mixture quickly decays into the so-called heavy fractions that inevitably clogging the carburetor;
• After removing the fuel, it is necessary to start the engine and let it work on xx until he himself stalls; Similarly, the remnants of the mixture will be eliminated from the internal combustion engine in full.

Particular attention must be paid to the preparation of the tool for long.term seasonal storage. This should be done to minimize the risks of problems with the launch of the engine. Competent preparation includes the following manipulations:

• completely disassemble the trimmer for the grass;
• Rinse and clean all the elements to which there is access;
• examine the parts of the lawn mower in order to identify defects (mechanical damage detected in this case should be eliminated);
• pour motor oil into the gearbox;
• carry out high.quality cleaning from clogging of an air filter element;
• Having appropriate knowledge and practical skills, you can perform partial disassembly of the power plant with subsequent purge and lubrication of moving elements;
• pour the collected gasoline braid with a pre.oiled rag.

In addition to all of the already listed, it is necessary to lubricate the piston group. This algorithm provides for the following simple manipulations:

• extract a candle;
• translate with the starter the piston to the upper dead point (VMT);
• pour a small volume of motor oil into the cylinder;
• Shine the crankshaft several times.

Regardless of the cost and brand of equipment, you should clearly comply with all the requirements of the relevant instructions and adhere to the recommendations of developers and experienced specialists. Today, detailed information regarding the correct use of such technology can be easily found on many specialized sites and forums.

It is important to remember that competent operation of motorcycles and its timely maintenance (independent or in the service) is the key to the longest possible service life and minimum expenses.

Next, watch the video on how to determine and eliminate the reason why the gasoline trimmer is not started for grass.

Why is the lawn mower stall at idle

Why does the lawn mower stall when you press the gas: the prerequisites and their solutions. The lawn mower stalls (trimmer for grass):. On idle

Users have repeatedly ask about stopping the braids for the grass “on hot”, that is, when the mechanism started, worked a little, and then took it. and stopped, stalled. The reasons for this situation are the following:

• problems with the carburetor damper;
• Gasoline in a carbe can even boil;
• If the ignition is damaged, then the trimmer for the grass will also heat up and stall.

In each of the situations, check the details for strength, and if they have already outlined their own, order new ones from specialists. We will call one of the most popular situations: the lawn mower stalls at idle. This happens for reasons:

• The carburetor was diluted himself, or was illiterately adjusted;
• the carburetor is contaminated;
• The air filter is very contaminated;
• The use of inappropriate fuel can cause a reduction in the gearbox revolutions;
• At idle, your trimmer for grass can stall if the throttle closed;
• Air fell into the carba system;
• The lawn mower receives a missing portion of gasoline to work fully, and therefore stalls.

We are sure that you received the maximum of useful information, and found a way out of your individual situation through our technical councils. Any spare parts, like a starter, motorcycles, its components and accessories are located at the lowest value in the country. Hurry up!

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold.

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns.

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

• reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
• clogging of the throttle;

• air entering the system;
• not enough fuel for the operation of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The lawn mower stall when you press the gas, how to eliminate the breakdown

Reasons why the lawn mower stalls

Similarly, when you press the gas, the tool stalls because the drive has clogged. The following option is possible: the fuel does not come in full, so you need to check or replace the fuel filter. To other possible reasons, the stalled motorcycles, when you give gas, should be attributed:

To all these reasons for which the mechanism stalls when adding gas, we will add several useful recommendations for the treatment of a motorcycle. First of all, before starting working with any equipment, you need to read the instructions. In this case, an important role is played by the consistency of gasoline and oil, correctly prepared by you, and also not to overheat the unit, and not leave gasoline for the winter when you simply will not use the machine.

In the full work of any tool, an important role is played by the coordinated work of all its components. And if in one it. then in another piston or carburetor. Motokos owners who want to use their tools at full power, you need to understand that the load on which the capacity of the machine is not designed may simply break the entire mechanism or its individual parts. Therefore, only competent and moderate operation involves the long.term effective work of any benchmate tool.

The trimmer stalls for grass at idle. the causes and their solutions

To common situations why the trimmer for grass stalls

or a lawn mower, it is worth attributing its work at idle. Let’s immediately move on to the reasons:

The insufficient amount of fuel that you need to work as a gas tool will entail a situation when at high speeds, with an increase. a trimmer for grass works and stalls in idle. In a situation with a carburetor. the device will stall for a cold launch and “on hot”. For any user, Motokosa. Professional and Amator, it is important to understand that any tool problem can depend on the petty flying of the part, the release of fastening or clogging, as well as on the global breakdown of the important part of the mechanism.

A newcomer and experienced owner may face the problem of the stalled motorcycle, the situation arises with those who have been in use and completely new braids, and which ones we will understand this article. So, the tool can stall under load, immediately after starting, that is, it starts and stalls, when heated by the entire mechanism, at high speeds, or does not even gain momentum and stalls. In all these cases, in fact, the same systems, elements, nodes are involved, but the breakdown or malfunction of each of them, more precisely, the nuances, cause an individual above situation. The answer to the question of each user: why does the lawn mower stall

, You will get only on our website in the section of news articles.

To completely deal with your individual situation. carefully read the signs and related nuances at the time the braid for the grass stalls, and then it will be easier for you to find a way out and quickly solve the problem. If you need certain. then to do this wholesale, and the best store of gas.tools in Ukraine will allow retail, Benzo Zip will allow for Ukraine.

Not starting on a cold trimmer for grass. we eliminate the cause

On the cold.The reason is an air leak that does not allow fuel to download. In the camera.

After several jerks, he will start and stall, which is a normal phenomenon. What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? Putting the damper to the working position, start the tool again and start working.

And again the carburetor.

Well, even if after such bullying your trimmer does not start for the grass, you can’t do without disassembling the carburetor. It may very well be that everything is to blame for the gathering of the needle in it. In any case, the disassembly and washing of this capricious mechanism certainly will not hurt.

In general, when a trimmer for the grass began to be capricious and stall, it is advisable to carry out complete prevention: to completely change the fuel mixture, try another oil, and also mandatory change the candle. The gasoline trimmer for the grass does not start? Reasons and decisions on. Practice shows that in many cases, it is precisely cheap low.quality candles that are to blame.

We examined the most typical reasons why a trimmer is not started for grass. If the matter is something more “exotic”, do not pass the campaign in the service center. You will probably find smaller and obvious breakdowns yourself.

Why is a trimmer not starting for the grass: the main malfunctions and their elimination

As already noted, such situations are characteristic of trimmers who were inactive for a long period of time. Therefore, after detecting the problem, you need to immediately take up the search for a malfunction.

Fuel as source of problems

The first stage is checking the presence of fuel and its quality. First of all, they are convinced that there is a fuel in the tank. Those who have acquired the unit recently, often forget that the trimmer for the grass needs refueling. If there is no fuel, then the equipment simply cannot work.

If there is a fuel in the tank, but the trimmer does not start for the grass, then the owner needs to check whether he is acting correctly. In this case, it is recommended to study the instructions. If the launch is made correctly, then the malfunction can cause the inappropriate quality of the mixture.

• Oil. It should be special. intended for two.stroke engines. It is not recommended to save on the product, since the life of the equipment depends on the mixture. Trammers for grass with a four.stroke engine require pure gasoline, it is not mixed with butter.
• It is necessary to use not only high.quality gasoline, but also the brand that is recommended by the manufacturer of a particular model. If it is not possible to find out what fuel is necessary, then it is recommended to choose either AI-95 or AI-92, and the last gasoline is a favorite, since the first has additives that react with two-stroke oil. Other brands do not advise using.
• The correct preparation is shifted for a benzotrimer. It is noted that at first this stage is paid to maximum attention, but over time, kosari begin to mix the composition “by eye”, and this is already a serious mistake. The correct ratio of gasoline and oil is 25: 1. For a liter of the first, 40 ml of the second, two.stroke. Motor oil intended for a car is an inappropriate option, since at high temperatures the liquid loses (partially) lubricating properties.

The correct storage conditions of the fuel mixture are important. To save time, some owners prepare it for the future to use it in the coming weeks. This option is contraindicated, since the prepared fuel mixture quickly becomes unsuitable. The reason is the precipitation of oil loss. With this change, both oil products lose their properties. Even repeated stirring is not able to restore the initial quality of fuel. Therefore, they recommend preparing a certain volume: 2 liters, no more.

If everything is in order with gasoline and oil, then they start diagnostics. to check the spark plug.

Candle and its condition

At this stage of diagnosis, you need to stop in more detail. Most experienced owners who are already familiar with the question of why a trimmer for grass does not start, first of all check the state of contact contacts. Diagnosis of this element is carried out as follows:

• First, the spark plug is unscrewed, then inspect. If the electrodes are in perfect condition, then they should have a carpet whose color resembles a brick. Wet element, or white, black plaque on contacts indicates the presence of any malfunction. Pink and red electrodes. proof of a large number of additives in fuel. Such a mixture must be replaced.
• In the event that the spark plug is wet, this means that the combustion chamber has unbroken fuel. It is left in place. Candle contacts are cleaned, then dried (calcination is prohibited). After this stage, the candle is connected to the nurser.
• Then the ignition is turned on, the frontier handle is pulled. When everything is in order with the element, it must issue a constant spark. If it is weak or completely absent, then the verdict is one. you need to replace the spark plug.

There is another reason why a trimmer is not started for grass. This is a big gap that appeared between the contacts of the candle. A distance of 0.7-1 mm is considered normal. To correctly adjust the gap between the electrodes, use special probes.

If there is no such device, then the folk method is used. A razor blade breaks, folds its parts together. Then this “probe” is inserted between the contacts. Ideal. blades that enter tightly.

The problem is in the fuel and the carburetor

If there is a spark, and a trimmer for grass still does not show signs of life, then nuisance can lie in the fuel supply to the combustion chamber. To make sure that this node is to blame, they perform such actions:

• They are typed in a syringe or poured into a lid from a plastic bottle of about 20 ml of fuel.
• Then, through the candle hole, the fuel is neatly poured into the combustion chamber.
• The candle is returned to the place, put on the imminent, the engine is launched.

In the event that the trimmer has started for the grass, the problem may be in the fuel and carburetor. Когда эффекта от проделанных манипуляций нет, диагностику продолжают — проверяют высоковольтный провод. At the slightest suspicion, this consumption element is replaced by a new.

What to do if the engine is a trimmer for grass still refuses to work? In this difficult case, you can follow the following recommendations:

• In doubt about the candle and the high.voltage wire, it is better to immediately replace them.
• If, when checking the new sparkling candle, it was not possible to achieve a spark, then it is almost possible to say with complete confidence that the ignition unit is faulty. the coil came out of the system.

Check its serviceability simply: they twist the candle, then it is led to the trimmer body for grass. If there is no spark when the starter jerks, or it does not appear every time, then a new coil is required. This element can also be replaced independently.

How to avoid most problems?

The work of this seasonal equipment is very affected by its proper storage. over, this applies not only to a long “rest” in the winter, but also of short intervals of inaction. To protect yourself and the technique from problems, you need to adhere to a few simple recommendations.

• Before sending on a well.deserved rest, a tank trimmer for grass is freed from fuel remnants. To remove the entire mixture, the lawn mower is launched and allowed to work until the engine is stalled.
• The first operation after “winter hibernation”. pouring a small amount of oil into the candle hole. Before that, the piston is moved to the extreme position. Such a lubricant will facilitate the launch and prevent premature wear of the details.

Before starting working with a motorcycle, they must check the candle and all the main equipment components.

Reasons why the trimmer for grass does not start is quite a lot. But most of them can be detected and fixed independently. The main thing is the correct diagnosis, attentiveness and sequence of actions. And about how you can cope with problems, the master from the next will tell in detail

Carburetor adjustment and configuration

The maximum and minimum engine speeds, even idle is regulated by the carburetor. The stable operation of the lawn mower depends on the amount of fuel mixture and air. The lawn mower is not started with disturbed adjustment of the carburetor. The procedure for setting up the device for supplying fuel at low speeds (L), high speeds (H) and idle (T) is regulated by the same vints:

• The chainsaw should work for at least 10 minutes, since the adjustment is carried out in hot.
• The screw n is flooded smoothly to maximum speed, then turning on ¼, counterclockwise, reducing the speed of rotation of the engine shaft.
• The idle stroke is regulated by the screw T, ensuring that the braid for the grass does not rotate.
• The screw l is regulated, first opening the throttle as much as possible, and then smoothly reducing the speed to stable minimum.

After adjustment, a working one with cleaned filters, a proven ignition should ensure the operation of the engine. In the event of a malfunction of the carburetor, after its repair, it will again need to configure the supply system before starting the lawn mower.

Rare breakdowns that prevent the operation of the lawn mower can be:

The most important malfunction, the elimination of which is associated with the replacement of the engine may be the failure of the piston group of the engine. The cost of repair will cost about 70% of the cost of the product. To figure out the reasons why the lawn mower is not starting up will help

Proper care for the chainsaw

There are no unnecessary phrases in the operating instructions, everything that is proposed is aimed at the trouble.free operation of the lawn mower. Cleaning all parts after each cycle of work contributes to the light removal of not hardened residues and dirt. You need to clean only cooled nodes. This technique contributes to the quality of the air cooling of the engine and the gearbox.

For refueling, it is necessary to use fuel with oil recommended in the instructions. If you leave the combustible mixture in the fuel tank, the oil will float and dies on the damper when starting, worsening its adjustment. The mixture can give a sediment and score fuel supply in the carburetor.

When preserving equipment for the winter, make an audit, grease the gearbox and the piston system, wrap the entire saw in the oiled rags and store in a dry place.

It is impossible, dangerous for the instrument and health of the mowing, use a metal cable instead of fishing line. It cuts more efficiently, but the load on the gearbox and the engine increases. A demolished piece of wire when separating flies at the speed of a bullet. Effective mowing can lead to a speedy wear of the piston group of the engine. For greater efficiency of the mowing, it is proposed to use the profile of the “Star” fishing line.