How can you cut the clutch clip. How to disassemble the bearing

How to remove the inner clutch of the bearing remaining on the shaft of the cross.cutter of the drum

Good afternoon, I want to share with young masters my way to solve this problem. Sometimes it happens that the clip does not move the puller, in such situations I take an angular grinding and about 2-3 mm retreating from the edge of the shaft I make a deep cut, but not to the end, so as not to damage the part of the sleeve on which the oil seal will be located. Next, I take a chisel, or a shock screwdriver, depending on what is at hand, and with the blow of the hammer I break off the lower edge, not finished to the end. Then, having received a thin wall on one side of the clip, I put a shock screwdriver on the edge of the clip, and I beat several times, the clip is fecked and easily cracks. Then I take a car puller, lubricate the VD40 shaft, so that it would be easier and pull the clip, the shaft is in perfect condition. My method takes a minimum amount of time. Do not forget to use the mask and follow all safety instructions when working with a corner grinder. If you have your own way to solve this problem, you can write about it in the Комментарии и мнения владельцев.

Answers 23

Earlier, I also made a tied corner grinder and then a split, and stopped at the assembly of the shooter.Cooked this, always helps out.Bolt with a diameter of 3 cm-milky, between the bolt and the shaft I put the ball from the bearing.And using a 46 key size, a powerful lever is obtained, which allows you not to strain.But be sure to together with VD-40.

A good shooter, there is something like that, but it is not always convenient for them to shoot, sometimes you can scratch the mirror. I have to cut it more often, but before that I try to scroll the clip on the shaft with a gas pipeline key “Ala crocodile.”With small rings, it helps with a bang. And large rings (205, 206) are not scary to cut off, the shaft is thick, even if you cut a bit with the shaft, nothing terrible. The edges processed the edge and the new bearing comes in perfectly MEZA42 Oct 14

Super thing, tried to do this for mass production, but unfortunately it was very difficult and expensive. Alexragulin 28 Oct

Great shooting range. I want to do myself for a long time, there is everything except a free minute))). Therefore, either the Weadshka and the gas key, or the corner grinder plus chisel. But. Someday I will do it for myself. With the right tool, it is a pleasure to work muratvasilina July 29

Knocking out the clip

The stuck clip does not have a stubborn surface on which you can hit, so you need to put an inner ring and balls in it. They can be removed from an old jammed or broken bearing.A similar in size bearing is disassembled.

If it is plastic, then it is simply shredded by a screwdriver and removed. In the presence of a steel separator, it must be knocked out by blows of the punch between the balls. After a breakup, it breaks out with pliers.

The separator itself is no longer required, so you can not stand on ceremony with it. Having released the separator, you need to move all the balls under one side to get the lumen.

After displacement from the bearing, balls fall out, and the ring is removed from the upper clip. This is easy, you can cope without a vice.

Now you need to put the extracted parts on the stuck clip in the case. For this, a thick lubricant is applied along its circle.

Next, you need to dilute the balls, distributing them evenly. They can be jammed, so you may have to use a screwdriver.

After assembling the bearing, it can be knocked out in the usual way. Before that, it is worth warming the case with a mounting hairdryer.

It will expand from heating, increasing the landing diameter, which facilitates knocking out. The head is applied to the back of the bearing and several beats with a hammer are applied along it. You can also use the puller.

This method will certainly make you tinker a little, but it is many times easier than an attempt to weld to a clip. No need to cut anything or drill, risking harm to the body in which the clip is sitting.

How to pull out the stuck outer clip of the bearing from the tank smell.

You need the same whole bearing. We disassemble it, then lubricate the clip with a lithol (first process VD-40) we insert the balls and straighten the balls in the inner clip and on the way. With the help of a hammer of a chisel and such a mother!!) Everything is clear in the photo.) I hope someone will come in handy.

Answers 30

I am successfully using to extract the outer clipping, a peorator, with a chipper function without rotation.The old drill on concrete, under a convenient corner, grind the end to catch a good clip and forward! Even a strongly shifted clip shifts, due to vibration!And also, welded to the old drill, the holder, for the heads and unscrew (and twist), that, it is difficult for a simple key or head!

Cool idea, only I will modernize and improve it a little, I will definitely shoot video, thanks. Alexragulin 8 Oct

And you did not try our puller https: // Texnomag.RU/Products/21 ? Everything happens much easier and more professional, especially now the price for it is reduced so far

How one of my friends likes to say. There is no difficult but there is a lack of the desired tool EM232 5 Oct

I heat and cool sharply, business 15 minutes. Unfortunately, the shooter does not always get it, it takes a lot.

I do the same. After that I have never been tormented yet. And without heating you can kill the crew)))). 89029518724 November 17

I score an old bearing on top. A couple of drops of electric arc welding between the clip and bearing. I knock out into the old bearing. Flies out with a whistle, as it heats up.

The 3x lap filmmaker is much easier and faster to cope with this task, the paws in it unfold on the revolution and in the bearing he is intortured by his shaft. Further hammer and business in the hat.

In the car shop I bought several thick goals of different diameters to the clip, it is welded by the grades suitable for the size of the washer and after the clip is calmly knocked out then the clip is red.hot and I use the puck again

The presented method is really very good, used to use it, now Alexander R. I use, with the peorater, too, an interesting idea, I need to sleep

A few different diameters of the tubes, be sure to substitute something to the seat where to sit the bearing with flat, hold the pipe and hammer a couple of strong strokes, the wallpaper either starts to be removed, or it was several times, the wallpaper is then removed, work with the puller is much easier (not always true)

Better 2 cuts, opposite each other. So the clip is better weakened. Although, in particularly advanced occasions, this does not help much, the clip is chopping off slices of Shmakovvvmaxim1979 on November 1

I also make a couple of three.year.olds an electrical arc welding and immediately pour the water.I did not think of the as a pedorator.

I’m also using welding.To the outer ring of the clip on the inside I weld the rod, reinforcement 8_10 mm. And hammer on the back. Pavel6565 Dec 19

I’m also using welding.To the outer ring of the clip on the inside I weld the rod, reinforcement 8_10 mm. And hammer on the back. Pavel6565 Dec 19

How to make a bearings of bearings from the deaf holes from the bolt

Without a special puller, remove the bearing from the deaf hole, without damaging it and the seat itself, is very difficult. If such a tool is not available, it can be made from available materials lying in any garage. We offer the design of a simple puller that is easy to repeat.

Materials:

You need to choose a bolt, a little less than the internal clutch of the bearing, and cut it in half. If it is rusty, then be sure to drive the thread before that.

It is necessary to hide his head, and instead make a small fungus a hook that can pry the bearing from below.

An insert between the halves of the bolt is cut out of sheet steel. Its thickness should be enough to praise it, and the fungus clung to the bearing from below.

A larger ring is cut out of the pipe than the outer clutch clip. It will rest against the case in which it is pressed. You also need to choose a puck under the ring, and for convenience to weld it into it.

To use the tool, you need to insert a bolt into the bearing, put on a ring with a puck on top, and make a nut.

Then, a spacer is inserted into the slot between its halves. Now if you hold the bolt with a screwdriver and tighten the nut, then the tool will squeeze the bearing.

If the bearing sits tight, and there is not enough strength to hold the screwdriver, you can make a groove for the wrench on the end of the bolt.

The final results of testing tools are given in the photo below.

“Prize places” played a chain mini-saw and two hacksaws among themselves. It is with the help of one of these three devices, according to the author, that you can effectively cut the indispensable tank of the washing machine and, most importantly, to do it safe both for others and for the device.

How can you cut the clutch clip without the use of corner grinders?

If there is no corner grinder, but before it was mainly so, they took a hacksaw for metal and drank a little in a manual. The canvases quickly sat down, but there was no other way out. If the bearing was large, for example, the 319th or 322nd, did the tied, and then with a sledgehammer neatly, because it is very for a long time to cut such a long time.

If without manual labor, then a diamond cutter on a milling machine, and if with your hands, then a good hacksaw for metal (it was not so painfully sawn that; with a good stock of interchangeable canvases and a barrel from the tank’s gun, not weakly cut off the tank, not weakly cut off. )

Saw a steel clip from the bearing with a hacksaw for metal, without preliminary annealing, the matter is unpromising. The hacksaw canvas will simply slide along the clip, without applying a tangible damage to it. The file in this regard is slightly better, they can cut the grooves in the right places and then with the help of a chisel and a hammer break the clip. (Observe caution: the fragments can fly off at high speed and cause serious injuries). True, at the same time, there may be a large number of files, since they will quickly stupor. Especially with quick movements. In this regard, it is better to use a file with diamond spraying, it is much more durable. There is another proven method, but for this clip should be attressed on a steel blank. We pass through the clip across the clip, after which we strike with the help of a chisel along the electrode trace. You can also cut the clip without any tricks by a propaganda-acid cutter or electric welding. You can also a laser cut, but this is not available to everyone. Although there are firms offering laser cutting metal.

Diamond wire is pulled into the hacksaw (wire with diamond spraying) and slowly, a foal of the Chku with a water, you can at least saw a bearing, even a glass ball for fortune-telling. Patience and a little effort.

Remove the clip from the body

After the bearing has been dismantled, we will deal with the removal of the clip from the body.

First, apply grease to the clip. It is needed to keep the balls that we will install there.

We apply a lubricant to the clip.

Now glue the balls on this lubricant. Set them close to each other. It is not necessary to install all the balls. Two, three balls can be left.

Balls glued to grease.

Install the internal clutch of the bearing.

Now you need to dilute the balls evenly around the circumference of the clip.

We make balls around the circle of clips.

After the balls have been installed in the right position, it became possible to knock the bearing on its inner clip. You can start knocking out.

We knock out.

How to remove the cloth cloth from the body

If the bearing is scattered, then it is almost impossible to pull out a stuck clip. This is rare, but still happens. The task of extracting in this case is complicated, but remains an execution.

What is required:

The essence of the extinguishing process in this situation is to restore the bearing right inside the case. After installing the internal clip, everything can be removed in the usual way. To do this, you will need to choose a similar old bearing.

Next, the balls of the old bearing are assembled by a screwdriver under one side. After that, curved long.willed curves are inserted into the inner clip, and it is turned into a break.

A lubricant is applied to the external clip stuck in the case. Balls are glued to it from a disassembled old bearing. They need to be assembled under one side.

After that, the already assembled bearing is extracted as usual, with the blow of the hammer through the head or the puller.

Why might need to drill a bearing

The key reason why you need to make a hole in this part lies in the malfunction of the mechanical elements. Bearings often fail for the following common reasons:

• A very poor lubricant is used to lubricate parts;
• the getting of the mud in the bearing, the presence inside solid and liquid elements, which violate the tightness of the design of the part, as a result of which the lubricant begins to proceed;
• negative influence of electric current, which passes through the bearing;
• errors when adjusting the part associated with an increase in the temperature of the part, heating above the norm and the appearance of the backlash;
• Incorrect installation and improper installation of the bearing, during which there was a strong piercing of the conical coupling;
• Strong load on part.

For all these reasons, you may need to drill a bearing to rectify the situation.

But sometimes this action does not at all relieve the main problem and you have to completely replace the part.

How can you drill a bearing

The bearing can be attributed to hot details. It is not always easy to drill such elements. for this you have to purchase special drills designed for red.hot steel. The material from the BK8 alloy is perfect.

In order to drill a clutch clip, you must go through the following stages:

• Initially, it is worth launching a large drill into work;
• Gradually increase the drilling rate so that the process occurs faster;
• Each time add oil and constantly sharpen the drill so that the performance of the work does not decrease.

As a result, after 10 minutes of the clip will be drilled. Sometimes such work has to be twisted with a ball from the bearing. To do this correctly, you need to comply with all the stages:

• The drill is fixed in the cartridge, and the ball from the part is in a special vice so that it does not slip out;
• With a slight click on the part, start drilling the bearing without adding oil in the first stages;
• After the appearance of a small recess from drilling, you can add a little oil and increase the pressure on the ball;
• Each time add new oil to the hole so that the drill is more efficient to make a hole;
• Remove the shavings and install the ball from the bearing.

If the materials are correctly selected, and the procedure is observed, then the bearing will be high.quality drilled. This will save drivers from the eternal problems that he faces when breaking the car mechanism. This information will also be useful for ordinary owners of technology, which use bearings.

Details that are used in almost any mechanized machine. bearings. They hold the shaft in space and ensure the rotation of the axes. In other words, these devices are indispensable because they are able to increase the performance of the technical means. But in case of problems that are related to the operation of the equipment, the bearing may be drilled. In such cases, you will need a special drill for potatoes. With the right passage of all the drilling steps, you can easily eliminate the problem and establish the operation of this device.