How can you drill concrete without a perforator. Necessary tools

How to drill a hole in concrete without a peorator

In order to correctly drill the wall, it is necessary to take into account the material from which it is made, based on this, it is necessary to choose the tool.

• Rightly hold the tool while working. For example, the drill in the hands should be straight, and go to the surface in the vertical direction;
• For convenience, use an additional pen;
• Depending on the surface of the surface, choose the right drill.

• Concrete, stone, brick wall. Use a carbide drill, more often the victorious;
• Metal. Metal drill;
• Tiles, clay tiles. Special drills for these materials, from time to time they can be changed to a concrete drill with surfacing;
• Wood-piece stove, wood. For holes the least 10-12 mm, a metal drill is suitable, for huge, special drills for wood are used.

Ordinary drill or electric screwdriver

If you do not have tools outlined above, then you can do this work using an ordinary electronic drill or a strong screwdriver.

For the end of drilling, more time is useful than the introduction of a drill drill, but you can do everything without the help of others.

In this case, not counting the drill and drill, you also need a blow. Firstly, a small recess is done at the place of drilling using a pea and hammer.

After that, a working tool is inserted into it and begins to drill. If the drill stops, break the difficult areas again with a blow and continue to work.

There are also drill for holes that have a diamond coating. They are very durable, they are used in special drilling rigs, and therefore there are a lot. Therefore, they solve the problem of how to drill a hole in the concrete wall at home, at least inappropriate.

Choose a tool

What is necessary, the 1st question that the home master should ask for is not how to drill a concrete wall with reinforcement, but what. The main assistant here will be the peorator, because it is intended for stone not concrete. Without looking at this, even massive drills do not manage with a wall of more than 12 cm wide. How to make a stroke and fix a cable in it. Although if we are talking about foam concrete, the drill is preferable, because the peorator will simply break it.

Read how to score a pipe into the ground as a pedorator

It also depends on the properties of the drill whether it will be possible to drill a hole in the concrete wall.

One of the good options is to use drills designed specifically for a shock drill. Their working part is a plate made of strong metal. With the help of these drills, the question of how to drill a thin concrete wall can be considered solved.

Use of awl and self.tapping screws

Shilo is a universal tool that is able to help in many situations related to repairs, including this.

First you will need to take a pencil, measure and mark the place where you want to make a hole. To begin with, there will be a fairly simple point, since the awl in itself is thin. If there was no awl at hand either, you can try to carry out the same operation with a nail, gently driving it with a hammer.

It is necessary to nail thin or medium so as not to damage the surface of the wall. It is necessary to drive it to the end, because then it will be difficult to pull it out. The length of the nail directly depends on the required depth of the hole, but initially the hole should be made somewhat shorter.

Then this point on the wall must be taped to the desired depth. The latter directly depends on your goals for which the hole is intended. This ends with Shil, then self.tapping screws are used.

How to drill a concrete wall with a conventional drill or a pedorator: recommendations

How to drill a concrete wall with a conventional drill?. This question was asked by many masters when she had to hang shelves, cornices and so on.

Concrete is a strong material and therefore lends itself to drilling extremely bad. Even how to drill a wall in a panel house, the task may seem unresolved.

Although, if you know certain secrets, this process can be greatly simplified.

Choose a tool

So, the first question that the home master should ask for is not how to drill a concrete wall with reinforcement, but what. The main assistant in this case will be the peorator, because it is intended for stone and concrete. At the same time, even powerful drills will not cope with a wall of more than 12 cm wide. Although if we are talking about foam concrete, it is precisely the drill, since the peorator will simply break it.

It also depends on the quality of the drill whether it will be possible to drill a hole in the concrete wall.

One of the optimal options is to use drills designed specifically for a shock drill. Their working part is a plate made of strong metal. With the help of these drills, the question of how to drill a thin concrete wall can be considered solved.

There are also ring drills that have a diamond coating. They are very strong, use them in special drill units, therefore there are quite a lot. Therefore, they will solve the problem with how to drill a hole in a concrete wall at home is impractical at least.

The use of crowns

Often you need to get a large diameter hole in the wall for a socket. How to drill the supporting wall in this case? Then they use crowns that have metal attacks around the circle. Crings are found in various sizes, but 68-centimeter remain the most popular, which are designed just for sockets. Working with these details, the peorator needs to turn off the stroke mode.

There are such crowns for drifts. But they have a different nature-from a convertible volfram alloy. It is convenient to use them, since drill a hole in a concrete wall with a drill and at the same time make a hole in the tiles quite can do it. Such crowns are used only with powerful drills.

Boers are another device than drill a concrete wall. Their diameter is diverse. Experienced craftsmen advise making selection based on the diameter of dowels.

We drill the concrete with a peorator

So, how to drill a hole in a concrete slab using a peorator? The procedure is simple:

• The drill switches to the stress mode, after which the drilling begins; The tool must be kept strictly at right angles;
• After a while, the drill is moistened with water, this will help to avoid overheating;
• After the reinforced concrete wall succeeds, the drill, without turning off the device itself, must be removed;
• To clean the resulting hole from dust, the drill is launched several times.

I can’t drill a wall? The peoporator rested on something solid? So you need to try to make a hole in another place.

We go around the drill

How to drill a concrete wall without a penetrator? The question of involving a conventional drill when working with concrete remains unresolved. So is it possible to drill a concrete wall with a drill, everyone decides for himself. After all, the tool can break. And the procedure will take more time.

You can drill a hole in the concrete with a drill if you use a special tool. a punch. It’s easy to operate on them: to put a sharp end to the place where the hole will be, to hit it several times with a hammer, after which you can start drill.

It is important to prevent tools to overheat.

As soon as the drill stumbles on an insurmountable barrier, you need to use the punch again until the right goal is achieved. Here’s how to properly drill a concrete wall using a drill. Although it takes more time and requires a lot of effort, you can also use it for lack of a penetrator.

Diamond drilling

This is another way to easily drill a concrete wall. However, only professionals who have special equipment (high.power electric motor and the like) use it).

How to drill a frame wall? This is not a problem, because diamond drilling allows you to get holes of large diameter and depth, and without irritating the eye of dust. In parallel, water is supplied directly to the drill, so it is cooled. As a result, the obtained holes are distinguished by a neat appearance, and the appearance of cracks is completely excluded.

How to drill tiles so as not to crack? Look here. What is a conductor for drilling holes? Find out in this article.

The drilling of concrete walls in this method is carried out, as a rule, professionals of specialized firms. So it does not make sense to stock up on the installation of diamond drilling for independent work.

Read also:. for installing locks in metal doors. repairing oven at home. repairing interior doors. repairing plastic windows with your own hands. shower cabin with your own hands from tiles in the photo and manufacturing tips. repair of locks on the doors: how to make it yourself?

How to drill without dust: options than better

Construction work is always accompanied by dust and garbage, but using some recommendations and tips, it can be significantly reduced:

• The peorator leaves insignificant dust when working so that it does not fly around the room at the same time use a construction vacuum cleaner. Some tools of the tool have a built.in vacuum cleaner, which facilitates the task;
• Using a drill, it is best to make either a conductor at the end or heap, or make an envelope under the hole so that the garbage falls into it.

How to drill holes in a brick wall: the choice of tools and nozzles

To make a hole in the brick wall, a peorator with a drill or a shock drill is suitable, most often use the latter. Its power should be at least 600 watts, the minimum number of revolutions is from 2500 per minute. It is best to use a drill with a smooth power adjustment and a fast clamp function.

Applying the function of shock drilling, the drill becomes identical to the pedorator. The speed and simplicity of work increases. To make a hole in the brick wall, you need to use a dynamic blow method. Without this, the drill cannot catch on the inside of the brick.

Than to drill a carrier wall in a panel house with a penetrator

In most panel houses, the walls are made of concrete to make a hole with a peorator, you need to use the winning.

In addition to them, you can use special crowns. They have attacks on the circle. When using them, you need to turn off the shock function of the penetrator.

Experts use diamond drilling, for this you need powerful equipment and skills.

How to properly drill a reinforced concrete drill under the pipe

Using a shock drill for reinforced concrete, you need to use the Poorator mode and the winning. At first, the hole is made of a smaller volume, then more. The drill should be cooled periodically.

Important! Working with concrete, you should not get into the reinforcement, otherwise the drill will break. Using a special device, you can check where it is located.

How to make a hole in the concrete wall drill

It is difficult to drill a concrete wall with a regular drill. You need to install the winning cords and choose small revolutions. An dowel is inserted into the right place to help the tool to break through the surface. Further drilling should be alternated with blows to dowel.

If the drill does not have a speed adjustment, then it will not be possible to make a hole.

How to make a hole of a concrete wall in an apartment with a drill

For a small hole, you can use the punch. It will make, most conveniently, from a drill, a diameter of 8 mm. The end is sharply sharpened. The drill is placed in the right place, turning, while hitting it with a hammer. Moisten the drill periodically so that it works longer.

Work rules: tips

When working with tools, it is necessary to follow the safety rules and general recommendations:

• 1) Performing work protect the respiratory system, dust is harmful.
• 2) if you work outside, then you need to put fences 2.5 meters.
• 3) When performing work at an altitude of more than 1.5 meters, use a strong base. forest or goat.
• 4) Working as a tool, the turns must be turned on smoothly, and in no case should you turn off when it is in the body of the wall.
• 5) when drilling through the plaster, it is necessary to carefully study the communications plan so as not to hurt anything.
• 6) it is strictly forbidden to drill through a decorative coating.
• 7) Choose the right cord for each surface.
• Move the drill with water so that it does not overheat.

How to make a hole in the metal without a drill

How to drill a concrete wall with a conventional drill and a pedorator?

How to drill a concrete wall with a conventional drill?. such a question was surely asked the master, when she had to hang shelves, cornices not to the rest.

Concrete is strong material in connection with this is very bad for drilling. Even how to drill a wall in a panel house, the task seems to be unsolvable.

Although, if you know certain secrets, such a process for you to greatly simplify.

Eyes are afraid. Hands do it || How to “drill” a hole in concrete without a peorator

Eyes are afraid. Hands do it || How to drill a hole in concrete without a peorator my drill no drill

There are such crowns for drifts. But they have a different nature-from a convertible volfram alloy. It is convenient to use them, since drill a hole in a concrete wall with a drill and at the same time make a hole in the tiles quite can do it. Such crowns are used only with powerful drills.

Boers are another device than drill a concrete wall. Their diameter is diverse. In the vast majority of cases, when installing hidden electrical wiring, you can not do without such a dirty and noisy procedure as stroke. Experienced craftsmen advise making selection based on the diameter of dowels.

How to drill a hole without a drill

How to drill a concrete wall with a regular drill by a peorator?

How to make a hole in the metal without a drill. a metallist directory

Metal processing is carried out not only in industrial conditions. When performing repair work on a car, manufacturing structures on a personal plot or conducting a home repair, it is necessary to drill holes in the metal. At home, a hand drill is most often used.

This universal tool requires certain skills in working with solid products. You can purchase, or make a machine for drilling holes in metal yourself, but this is not a cheap pleasure.

The technology of drilling holes in the metal is to remove the thin layer of material due to the simultaneous progressive and rotational movement of the drill.

The main condition for high.quality and safe (for tool) processing is to keep the cartridge axis in a fixed position. With the help of the machine, it is easy to maintain straightforwardness, which you can’t say when working with a manual tool.

If you are not sure of the hardness of the hands (this is a normal situation for an ordinary person), mechanical assistants (conductors) are required to drill at right angles.

Immediately make a reservation that additional conductors are required only if the metal thickness exceeds the diameter of the drill.

If you make a hole in a thin steel plate, the straightforwardness does not matter.

Devices for drilling perpendicular holes

There are several varieties of guides for manual electric drill. Mechanical drive tools are poorly suitable for work with metal, especially when it comes to accuracy.

Conductor for drilling. It is made in the form of a case convenient to retain, inside which there are placed bushings for drills of various diameters.

The material of the bushings is stronger than the tool, so the holes do not wear out. By installing the conductor exactly above the center of the proposed hole, you can not worry that the drill will “take” from the given direction.

Such a device is especially useful when drilling perpendicular holes in small diameter pipes, when the tip strives to slip off the cylindrical surface.

The sole is placed on the workpiece, holding the hilt with the second hand. The drill moves strictly vertically, avoiding distortions and drill departments.

The design can have a corner holder for pipes of small diameter, which makes the device more universal.

In the presence of a rotary mechanism, you also get a device for drilling holes at an angle.

True, the metal cannot be drilled in this way, the side loads will quickly break the drill.

Popular: what is an anchor and why it is needed

A carriage with a fixed tool (for the same neck) moves along the rod with a lever. The workpiece is firmly held on the sole using a vice or clamp. The quality of the drilling is very high, but the cost of the device is considerable. Although in comparison with the drilling machine. this is inexpensive.

A device for holding a drill at a right angle can be made independently. It is enough to inhibit the holes of various diameters in a bar of durable material, for example, textolite or ebonite.

It’s not worth counting on side support only. it is rather a “device” for visual control. With a lateral deviation, the drill will quickly break the guide hole in the conductor.

The next problem is the drilling of deep holes

Technologically correct will be the use of a lathe. over, when processing cylindrical details (for example, the weapons trunk), the workpiece rotates, and the drill remains motionless. Mandatory cooling and forced detachment of chips from the hole.

For this drill for deep drilling, they have special grooves on the surface, or the drill is periodically removed from the workpiece for cleaning from chips.

At home, it is imperative to use guides for a drill. Masters recommend not drilling holes, with a depth of more than 2/3 from the length of the drill. As cooling, you can use ordinary water, the drill is periodically extracted from the hole for cleaning from chips and cooling.

The use of special long drills requires special technology.

As soon as the cutting part, along with the removing edges, is hidden in the hole, the chips will clog the grooves and block the rotation. Therefore, at the last stage, extracting the drill and cleaning of shavings is performed more often.

Drilling holes of large diameter in metal

Drilling large holes in the metal with a bimetal crown. video

This procedure is even more complicated than deep drilling. Drilling large holes is carried out either by a crown (for small thicknesses), or a regular drill in several stages.

• The crown for the metal is practically no different from a similar device for concrete or drywall. The difference in the material of the cutting surface and sharpening of teeth. The center is located a guide drill, which does not allow the crown to “leave the route”. The work is carried out at low speeds with compulsory cooling. The diameter of the hole is actually not limited, it all depends on the torque of your drill.
• Drilling in several stages. With a significant thickness of the workpiece, you should stock up on a set of drills with a difference in a diameter of 25%. Starting from the thinnest, we gradually move to the following dimensions, to the finish diameter. It is important to maintain the position of the center of rotation of the drill cartridge, so you can not do without a guide.
• Using conical drills. This tool is a set of sequentially located drills of different diameters on the general axis. If you process thin steel plates, it will be more convenient to use a conical stepped drill.

How to drill concrete without a penetrator-southeast

It may seem that drill a hole in the wall. a couple of trifles.

However, if it is wrong to choose the tool for a particular surface material, the drill can be dull or even break, and scratches and cracks may appear on the surface.

So that this does not happen, you need to know certain nuances of the work. How to drill, how to correctly prepare the surface and choose a drill, we will consider further.

The tool must be held correctly in your hands. The drill should be directly and entered in the surface in the vertical direction. To make it easier to drill and perform more accurate drilling, you can use an additional handle, which usually comes with a drill.

Based on what type of surface you work with, it is necessary to select the material and the size of the drill and determine the mode of operation of the tool.

Here is the main principle of how to drill correctly: the material of the cutting tool should be more solid than the material of the drilled surface. Imagine the following situation.

Suppose you decided to drill a concrete wall with a drill intended for a tree. There are no doubt that nothing good will come of it, and the drill will have to be thrown away.

Therefore, the type and material of the drill must be carefully selected for each surface type.

Drilling concrete wall

The choice of drill. If the surface is brick, stone or concrete, the drill must be taken. Typically, winning drill is used for such purposes. They do not cut the material, but turn it into crumbs, therefore, for concrete or stone walls are suitable as possible.

But in order to make a hole in plastic, wood or steel, they are not intended. If you try to drill a wooden wall with a winning drill, the wood fibers will be torn, and the hole will be ugly, inaccurate and larger diameter than necessary.

Drill steel using such a drill will not work at all.

Drill, a drill for a peorator and a crown on concrete.

Surface preparation. Before drilling the wall, it is necessary to make sure that there is no wiring, heating and water pipes on this section of the wall. For this purpose, it is most convenient to use a metal detector.

He reacts both to iron and steel objects, and to objects from non.ferrous metals. With the help of a metal detector, you can find out where the electric cables take place and determine what depth you can perform drilling.

Holes with a diameter of less than 13 mm are performed with a drill, and wider holes with a pedorator. However, several large holes can be drilled with a drill if its cartridge is suitable for a conical drill with a diameter of 13 mm.

Drilling process. First, it is necessary to outline in which place the hole will be made.

It doesn’t matter use a shock drill or a peorator, in some cases, in order to start drilling, you need to convert the device into a simple drilling mode without shock and at small speeds to make a deepening.

It is easier to start drilling, the drill will not jump on the surface and you will be able to more accurately drill. And after you have outlined the place of the future opening, you can go to the shock mode and add speed.

If you use plastic dowels, the hole should be deeper than the length of the dowel. As a rule, in the process of drilling, a certain amount of crushed material in the form of dust remains in the hole, it is necessary to leave a 10 mm length reserve of length.

Those who have repeatedly worked with a drill know that it is sometimes difficult to keep it in the necessary position. The tool itself has significant weight, in addition to this, vibration occurs in the process and dust flies. To avoid dust entering the operator and on the tool itself, there are special dust bands on the market today on the market.

Drilling metal

The choice of drill. To perform a neat hole in the metal surface, you should purchase a high.quality drill for the metal.

Cheap drills in this case should not be used, since they will not only not drill the base, but also deliver a lot of trouble.

Therefore, try to buy only proven, high.quality drills of well.known manufacturers. Normal

Varieties of drills and crowns on metallo.

Surface preparation. Before drilling the metal, it is necessary to tap the middle of the hole so that the drill does not slip off the surface.

This work is performed using Kerner, which is a pointed metal rod. They hit the coreer with a hammer, and its tip is knocked out in the surface.

Thanks to this, the drill can be fixed in one position, and the hole will turn out to be correct and neat.

Drilling process. To make a hole in a metal, the thickness of which exceeds 5 mm, it is advisable to use several drills. First, the work is performed by a drill with a small diameter, and then finished with a large drill to the desired diameter. First, the drill is turned on for small speeds, then the speed is slightly increased.

It was easier to drill the metal, it is desirable to put the board under it. This will make the holes more even and neat.

When the metal processing is performed, the drill is heated. It is advisable to lubricate it with special paste or cooling liquid before work. If you do not have it, ordinary machine oil is suitable. The exception to this rule is the gray cast iron, which will always drill dry.

To pull the drill out of the resulting hole, you need to turn the drill in the opposite direction, if there is such a function in its mechanism.

Often a drilling rack is used to drill metal, to which the tool is attached. In this case, at the beginning of work on its handle, it is necessary to press only slightly, and when the chips go, the pressure of pressure should be increased.

Drill installed in the drilling rack.

There is a direct connection between the thickness of the drill and the number of revolutions of the tool. Remember that the larger the diameter of the drill, the lower the speed. Suppose if you use a 4 mm drill in diameter, the tools of the tool are about 2400-2800 per minute. If the diameter of the drill is 6-8 mm, the number of revolutions is much smaller-approximately 1200-1300 per minute.

How to drill concrete without a penetrator

How to drill a concrete wall with a drill: as well as drilling with a peorator. Diamond drilling

When performing work on decoration, it is necessary in the performance of the hole in the wall, for example, to fix the iron profile during the installation of drywall.

If the wall is concrete, then this procedure causes certain difficulties, because the myth of the material has the highest strength, has a heterogeneous structure and contains iron reinforcement.

Then it will be considered what methods it is desirable to resolve this case.

Necessary tool

Due to the features of concrete, a special tool is useful for its drilling:

• Peoporator (drill of shock act)-provides rotational-compliance with the drill.
• Drill on concrete. made of hard alloys. Their shank and the screw.shaped part are made of instrumental steel, and the cutting working area is a plate of carbide metal, sharpened at 60 degrees, which is sealed in the groove of the cutting part of the tool.
• Punch (is needed when drilling an ordinary drill).

It should be noted that it is possible to cope with the task and inventory without impact function. Below we will see in more detail how to drill a concrete wall with a drill.

Cooled drill on concrete for a drill

The procedure for drilling by the ashorator

The procedure for drilling the wall with a peorator and a special drill is quite common:

• The concrete drill should be switched to drilling mode and start the operation. The drill should be placed strictly at an angle of 90 degrees relative to the wall, not counting in cases where drilling is specially carried out at a certain angle.

• A few days later, the drill must be moistened in cool water and continue to work.
• If the tool rested on something tough and finished deepening, you will have to try to drill the wall where you pleased.
• When a suitable immersion depth is reached, you should remove the drill without turning off the drill. To clean the hole from the dust, you need to deepen several times and remove the drill.

Advice! The peorator is used not so much to perform drilling hard materials. There are special nozzles that turn such a tool into a mixer.

How to drill concrete without a penetrator

Come in. Thanks to them, the drill is a mixer for concrete perfectly copes with stirring the solution.

Drill drill

Many home masters doubt whether it is possible to drill concrete drill? Of course, this procedure will take much more time than when working with the peorator, however, it is quite possible to execute a hole.

To perform this operation, you will need a special punch. This tool is a rod with a pointed hard end. It is used to break the surface in the drilling area.

The instructions for performing this work are as follows:

• First of all, to the place where the future hole will be located, you need to put a punch and hit it several times with a hammer.
• Then, a drill is inserted into the resulting funnel and the hole is drilled. As when working with the pedorator, it is necessary to ensure that the tool does not overheat.
• If the drill has stopped deepening, you must again use it and the punch. insert it into the hole and hit it several times with a hammer on it.
• In this way, the desired depth of the hole is reached by.

Advice! Often there is a need to cut concrete, in which case, a corner grinder is used. However, it should be borne in mind that the cutting of reinforced concrete is performed with diamond circles.

As a result, although the usual drill for concrete is not suitable, for lack of a peorator, with its help you can also drill a reinforced concrete wall.

Advice! The drill can be used not only to make holes, but also to use it for some other purposes.

For example, on our portal you can find out how to make a vibrator for concrete with your own hands from a drill.

How to save on a pedorator and drill a concrete wall with a regular drill?

Many people live in houses with concrete walls, and when it becomes necessary to make a hole in them, they meet with serious difficulties.

Do not despair and be upset if you could not immediately hang a shelf, lamp or cabinet, read our recommendations and everything will work out.

There are several options with which you can independently drill a concrete wall.

How to make a hole in concrete without a penetrator-south-zbk

Concrete is considered tough and strong material, due to which it is very popular in construction. But, in connection with these qualities, its mechanical processing causes specific difficulties.

In particular, the task often appears before home masters. how to break the hole in concrete?Then we will try to answer this question and examine more effective methods of obtaining holes in concrete surfaces.

The choice of the method of obtaining holes in concrete is dependent on the tasks: if you need to get a hole of small diameter, to the sample, to install dowels in concrete, then a peorator is used with a special brown that has a carbide tank.If you need to get a large diameter, to the sample, to carry out pipes, installation of sockets, etc.D.

, use diamond drilling holes in concrete with the support of special crowns.Now we will examine two technologies in more detail.

Boers or as they are still called, the drills on concrete have a screw shape of the rod and, as has already been uttered, a carbide tip.

The shank has the ability to exist smooth and cylindrical, prepared for shock drills, or executed according to the SDS standard, for peorators.

With their support it is allowed to perform holes of small and medium diameter.The abstract on the implementation of this procedure looks as follows: before that, than to break the hole in concrete, you need to outline the space that you need to drill.Then the tip is inserted into the cartridge of the pea or drill. In this case, the depth limiter is set to the necessary state.

Then the drill should be rested at the intended point and connect the tool. In this case, it is necessary to fulfill a certain emphasis on the nozzle. At times, the drill should be excluded from the hole and wetted with water, preventing it from overheating.

After the way the desired depth will become, the work is stopped.I must say that you can make a hole with an ordinary drill without impact. But, for this one, a punch with a hammer will come in handy.

In such a situation, the drill must be excluded from the hole and break the concrete with a punch.

Eyes are afraid. hands do || How to “drill” a hole in concrete without a pedorator.

Eyes are afraid. hands do || How to “drill” a hole in concrete without a penetrator my drill did not “take” concrete “. Even a small deepening did not work.

Of course, if you need a lot of holes, then you can’t do without a penetrator. And if you need 1-2 holes, and there is no time to look or wait or wait, then you can do this way.

How to drill a concrete wall correctly

The repair process in the apartment includes many works related to the creation of holes in the walls: for this, a tool of various designs and power can be used for this. Many masters and those who are going to carry out repairs on their own, want to find out how to drill a concrete wall with a regular drill and is it possible at all. A peorator is usually used for such work, but it is not always suitable for this, moreover, if the tool is to buy, then its cost is much higher than that of the drill.

Before starting work, it is important to decide which drilling device is better to do the work. The choice, of course, is small, since there are two types of wall drilling:

The peorator will better cope with this work, since its function is precisely punching concrete or stone surfaces. Using this tool, you can make a large section, but even the highest quality shock drill is not able to drill holes of more than 12 cm.

What walls can be demolished in Khrushchevka

But when it is necessary to drill foam concrete walls, the drill will be optimal, since the peorator will simply crush the surface.

When working with concrete walls, it is strictly impossible to use an unstressed drill, because it will be meaningless, in addition, you can ruin the tool.

When only a few holes have to be made and there is no peorator, you should not purchase it because of this, you can do it and the drill. If a lot of work is done, then the purchase of a peorater is inevitable.

In the case when it is still necessary to work with a drill, it is important not to forget that you need to use a winning drill on concrete and it is with the tip covered with carbide.

Features of the choice of tools

In most cases, it is better to use a peorator for concrete drilling: it has an increased power, designed to break through solid surfaces, and allows you to make large in diameter of the hole. The use of the tool is impractical in the following cases:

• the need to drill the wall to a depth of 10-12 mm;
• work with foam concrete, which crumbles when processing by the ashorator;
• The work needs to do no more than 10-15 holes.

Before drilling the wall, it is important to choose the drill itself: it should not be unstressed, since such a variety is ineffective when drilling concrete, nozzle and cartridge almost immediately become unusable. The nozzles themselves should be winning, intended for concrete work, the tip with carbide.

In some cases, a successful solution will be the purchase of a drill-pediatric drill: the device is more expensive than a classic model, but is characterized by increased power, which can be adjusted.

What to do if, when drilling holes in concrete, the drill is overhand in the wall

Basically, the drill jams as a result of the hit between a piece of crushed stone and reinforcement, especially with deep drilling. If, when starting the tool, only a characteristic buzz is heard and nothing more, then this is a clear sign of a stuck tool. Starting work, it is important not only to know how to make a hole in the wall, but also how to extract a stuck nozzle.

If the drill is equipped with a reverse function, then you can try to turn it on. Due to reverse rotation, the drill will be released. This method is suitable if the stuck was noticed right away, and the situation did not have time to aggravate.

Otherwise, the first thing to do in such a situation is to stop the process and turn off the tool. It is useless to try to extract the nozzle with your hands or drill right away, since the drill can break off. In this case, it will be more difficult to remove it.

The stuck nozzle is taken out of the drill, and another drill of smaller diameter is inserted into the tool. Gently, without touching the nozzle, free the space around the jammed part from concrete. Когда освободится достаточно места, бур можно вынуть из стены руками или длинногубцами.

There are more unusual ways to get a stuck drill. When a significant part of it sticks out of the wall, you can put on it a gas key and try to promote it in the opposite direction. If you can’t turn the key with your hands, you can try to do this with a hammer.

It happens that a drill stuck in the wall breaks. Getting a fragment is much more difficult than a whole nozzle. You can free the space around the fragment with a new drill and then try to shake and get it with pliers. It’s hard to do if the fragment is deep.

Another way: drill a fragment of a larger diameter nozzle. The already made hole expands to a piece of a stuck drill. Further there are two options: with a thin drill, expand the space around the fragment or try to immediately remove the fragment with long.ruble.

If the place for the hole in which the nozzle is stuck is rigidly fixed by the plan of the room and it is impossible to transfer it to a few centimeters, then the nozzle or fragment must be removed, and insert a wooden cork (nagel) to the place of the expanded opening. Otherwise, it is easier to leave the fragment in the wall, and the piece sticking out (if there is) cut down. The hole formed during the release is sealed with a solution.

Precautionary measures

Of course, any person can drill a couple of small holes in a concrete wall. It is enough to have a good drill with the function of the impact or the peorator, as well as the winning or diamond drill of the desired size. If you have to pull large diameter pipes, for example, to remove the ventilation pipe from a gas boiler to the street, then it is better to entrust this matter to professionals. This will make work with the least costs and damage, as well as save the psyche of not only the owner of the apartment, but also his neighbors.

When drilling concrete walls, do not forget about personal protective equipment. In order not to swallow dust, you need to use a respirator. And special glasses will protect the eyes from the hit in them with a fine concrete crumb.

The use of crowns

Often you need to get a large diameter hole in the wall for a socket. How to drill the supporting wall in this case? Then they use crowns that have metal attacks around the circle. Crings are found in various sizes, but 68-centimeter remain the most popular, which are designed just for sockets. Working with these details, the peorator needs to turn off the stroke mode.

DIY

The circular saw of the drill is the entire machine (without an electric drill) consists of the base, on the desktop, four racks of not two holders: the drive (electric drill) not the free end of the shaft of the saw disk. For the base, a furniture (lined) wood.made slab with dimensions of 300 × 250 mm was used not with the thickness of Thirty mm. For the table (workplane), stiff duralumin plastan is selected with thickness Four mm not []

We drill the concrete with a peorator

So, how to drill a hole in a concrete slab using a peorator? The procedure is simple:

• The drill switches to the stress mode, after which the drilling begins; The tool must be kept strictly at right angles;
• After a while, the drill is moistened with water, this will help to avoid overheating;
• After the reinforced concrete wall succeeds, the drill, without turning off the device itself, must be removed;
• To clean the resulting hole from dust, the drill is launched several times.

I can’t drill a wall? The peoporator rested on something solid? So you need to try to make a hole in another place.