How many meters of fishing line to wind on the grass trimmer reel

Replacing the fishing line on a trimmer or brushcutter

To replace the fishing line on the trimmer or brushcutter (cord, string), first of all, you need to know its thickness. If the remains of the cord are not preserved, then study the passport of our garden equipment. Sometimes the right information can be found by carefully inspecting the mowing reel, the range of diameters can be plotted on its surface. If our search is unsuccessful, we simply estimate the diameter of the exit hole on the spool. The line should move through the bobbin with no effort. I do not recommend widening the holes to use a thicker line to increase output and capacity of the garden equipment. The thickness of the line is calculated by the manufacturer according to the engine capacity.

To replace the cords on most models you need to disassemble the mowing spool by pushing on the catches. Sometimes at the same time as pressing the latches, you have to turn the upper part of the spool as well.

A standard bobbin is filled with 5 to 6 meters of thin cutting line or up to 3 meters of thick line. figures are approximate, it all depends on the size of your mowing head. If it overheats while mowing, it is better to refill less mowing line. There is a chance it will sinter and you will throw it away.

In the simplest trimmers and brush cutters is a non-automatic spool with one tendril. It is very simple, one edge of the line is inserted in the slit inside the bobbin. Then reel in as much cords as you can fit under the guard, following the arrow. 10 cm of the cord is led through the holes in the protective casing and spool and assembled.

Non-automatic single-tendon spool

Semi-automatic single spool with 2 tendrils

Semi-automatic 2-section spool with 2 tendrils

If the line on the trimmer has 2 tendrils, then before winding the string is folded in half, shifting the edges by 5-10 centimeters. The bobbins come in various designs, but each one has some kind of catch for securing the middle of the cord. If the spool single section, there is a hole where you need to put one end of the line and center it again. In the two-section bobbin there is a notch in the septum.

Wind-cord and winding direction arrow

The inscription “Wind-cord” and the arrow show us the winding direction. If there is no arrow, then wind it in the opposite direction to the direction of rotation. Hold the edges of the cord with one hand and turn the bobbin with the other, winding the line on its track. lay the string rather tightly, it is not necessary to be perfectly straight, the main thing is to prevent junctions. It will move into place during operation. When we have 10 centimeters left, we fix the edges in the slots. Insert the string through the holes in the body of the reel. Alternately jerk the line lightly so that no loops form inside, and insert the bobbin into the bobbin. Then reassemble the spool. Sometimes there is a bobbin design that when it is assembled, the edges of the string should be released from the slots of the bobbin. To check the correctness of the assembly of the semi-automatic head of our garden equipment can be simulated by tapping the grass trimmer on the ground. Press the button in the center and simultaneously pull the edges of the line. If everything is all right, the tendrils are slightly stretched.

On Oleo-Mac brushcutters cutting spool does not need to be disassembled at all. Simply threading the string through the holes. Center it, and by rotating the “wingnut” in the direction of the arrow, wind the cord. Changing the line on your trimmer is very fast, this design is starting to occur more and more often.

I hope you will find the article on the correct choice of fishing line for your gardening equipment Forest for grass trimmer, string, cord for electric and brushcutter.

What can be used instead of a fishing line

Many trimmer users wonder what can replace the default cord used in this kind of machine? Begin to conduct unsafe experiments, installing metal or copper wire, metal cables or strings, as well as ordinary fishing line in the mowing head.

Read also: Weaving machine with his own hands blueprints scheme

If you install a metal cable instead of a fishing line, the grass trimmer becomes a dangerous device not only for the user, but also for others. This is explained by the fact that during the operation of the machine, the steel wire will gradually unravel, and the small pieces of wire will fly in different directions at high speed.

Similar happens when using steel or copper wire, the only difference is that the pieces torn off will be larger and can cause serious injury.

And if you accidentally catch your own or someone else’s foot when working with the steel wire, a strong and deep cut in the tissue, and in some cases even amputation of toes, is guaranteed. The manufacturer does not use nylon for nothing, because it is quite light and strong, and when torn off, it does not fly far away and can not cause injury.

EASIEST WAY TO STRING YOUR WEED EATER

You can certainly use fishing line in the trimmer instead of the standard one, but it will add extra hassle because it wears out quickly, tears, mows slowly and is not suitable for cutting tough grass. In addition, much time is lost replacing a broken tool more than once during work.

In practice, the installation of ordinary fishing line is justified, if the user is going to mow grass near a fence, especially if it is made of Rabitz chain-link. In this case, in order to save standard and sometimes expensive cord from wear and tear, it is replaced with fishing line, which is not sorry. Usually, to change the cord on the line, it is necessary to pick up the greatest thickness. 2-3 mm.

How to correctly wind the fishing line on the grass trimmer reel?

Store-bought grass trimmer is ready to work. it is filled with a standard kapron fishing line. It cuts grass, but copes with the work poorly. quickly fails and mows only young, thin plants. Old grass and weeds with woody stems it does not take at all or cuts with difficulty, quickly wearing down. It only lasts a short time, after which you need to replace the line in the trimmer.

It is not recommended to use fishing line, it is better to take a special thread with a core of fiberglass. It is sold in construction stores. Choose one with a square or triangular cross-section. its sharp edges will work like knives.

Consumption of fishing line for grass trimmer when using faceted and reinforced consumable material will be reduced by 2-3 times, the same amount of time will increase productivity compared to round section fishing line and non fiberglass reinforced fishing line.

Purchase the material with a diameter no smaller than that recommended by the manufacturer. If you don’t know the diameter, look at the size of the holes on the outer casing of the mowing head: the diameter of the working thread should be a little less than the hole to go through it freely.

Buy a sufficient supply of cutting thread (for 2-3 changes), try to buy different versions to compare which one will work best.

Once you know how much line you need for one reel, use this as a guide for the next time you buy the line, so that you don’t leave any pieces that are too short for reeling.

To replace the fishing line on a mechanical mower with your own hands, you need to disassemble the mowing head and take out the spool, on which the working thread is wound.

How to wind the fishing line onto the grass trimmer spool

First determine the length of fishing line for your reel. Wind the line on the bobbin until it touches the bobbin’s edges. We have 4 meters. How much you will come out depends on what diameter of line for the bobbin and the peculiarities of construction.

Algorithm of winding

Fold the line in half. Leave one end 10 to 15 cm longer than the other.

Insert the resulting loop into the groove.

Lay the line according to the direction shown on the piece.

Insert the short end into the groove on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of fishing line in the bobbin case.

Pull the fishing line out of the fixing grooves.

Put on the cover and fasten it.

Cut the ends of the line, leaving 10 to 15 centimeters.

The filament change is complete and you just need to screw the bobbin onto the weed trimmer and go to work.

What you can use instead of a fishing line

Many trimmer users wonder how to replace the default cord in this type of machine? Begin unsafe experiments by installing metal or copper wire, metal ropes or strings, and ordinary fishing line into the mowing head.

If a metal cord is used instead of a fishing line, the weed trimmer becomes a dangerous device not only for the user, but also for others. The reason for this is that during the operation of the unit, the steel wire will gradually unravel, and the small pieces of wire will fly in different directions at high speed.

The only difference is that the pieces that break off are larger and can cause significant injury.

And if you accidentally catch your or someone else’s foot when working with a unit with a steel cord (wire), you will get a strong and deep tissue incision, and in some cases amputation of toes. It is not for nothing that manufacturers use nylon for this purpose, as it is quite light and tough, and when torn it does not fly far away and can not cause injury.

You can, of course, use fishing line instead of a standard line in a trimmer, but it will add extra hassle because it wears out, tears quickly, mows slowly and will not cut through tough grass. In addition, a lot of time is wasted during work to replace a broken tool more than once.

In practice, the installation of an ordinary fishing line is justified if the user is going to mow the grass near the fence, especially if it is made of Rabitz chain-link mesh. In this case, in order to save the standard, and sometimes expensive cord from wear and tear, it is changed to a fishing line, which is not sorry. Usually, to change the cord on the fishing line, it is necessary to pick up the greatest thickness. 2-3 mm.

What is the best line for a grass trimmer?? How to wind a fishing line on a brushcutter reel?

Grass trimmers are used for mowing lawns and clearing different areas of excess vegetation. The technique is suitable for domestic and professional use. Grass trimmers work electrically with a fishing line and a knife. Before buying a grass trimmer, all components of the device are evaluated, including the choice of fishing line.

What is the best line for the grass trimmer?

When choosing a fishing line, you need to take into account several of its parameters.

The list of the main characteristics of the cutting cord includes:

• The thickness of the fishing line. on the market, most often there are threads with a thickness in the range of 1.2-4 mm. Thin cord, no thicker than 1.6 mm, is designed for trimmers, whose power does not exceed 0.8 l. с. Most often this cord is used in cases where a household has a low-powered electric mower with a line and knife. Cords with a diameter of up to 2 mm to 2.6 mm are used for trimmers, 1 to 1.8 l. с. These lines are able to successfully remove not only freshly grown, but also quite old dried out vegetation. Thicker lines with a diameter of 3 mm or more are intended for use with petrol-powered brushcutters with a power of at least 3 liters. с. Cord with this thickness performs well when mowing large and dense wild vegetation;

• the shape of the grass trimmer cord. a lot depends on this factor, because when you mow the grass, the cord does not cut the stems, but hits them repeatedly. It is the shape of the cord that affects the speed of cutting the grass and the neatness of the mowing line. Most often circular lines are available on the market. This cord is suitable for mowing any kind of vegetation. Slightly less common on the market is a square thread. It is best for removing large, hard stems, and is often used for mowing wild shrubs. Starfish line is also available on the market. It stands out for its low traumatism to the grass, so it is best used for the care of ornamental natural lawns;
• material. in most cases, manufacturers use nylon, polypropylene and polyamide to produce the cutting cord. Cheaper trimmer cords are made of nylon with polyethylene additives, which significantly reduces the resistance of the thread to wear and temperature.

How to remove the spool from a grass trimmer?

To change or wind the cutting filament on the spool, it must be removed.

How difficult it is to remove depends on the tool model:

• Low-mounted tool. motor here is almost at the ground. To remove the reel, you need to press the buttons located on the side of the grass trimmer. After pressing these buttons, the housing, where the spool of fishing line is located, is opened.
• Grass trimmer with a curved shaft. Here it is necessary to turn counter-clockwise the special thumbscrew. After that, the spool and the spring in it are removed.
• The tool with the straight boom. Hold the rod stationary with a screwdriver or other object. Turning it clockwise removes it. After that, the tool is disassembled into parts and the reel is taken out.

• If the tool with a single tendril is used, about four meters of thread will be needed. This thread is passed through a hole inside the bobbin where it can be secured. Next, one end of the fishing line is guided by the arrow. The end of this thread is then secured in the groove that is in the bobbin. This is to ensure that the thread can not unwind when assembling the spool. If there is no groove, you should hold the fishing line with your hand and assemble the bobbin.
• If a tool with two tendrils is used, first check the number of available grooves.

If the spool is equipped with a semi-automatic mechanism, you wind up the line as follows:

• The thread is threaded through the hole that is inside;
• Secure the ends of the thread in the grooves on the body.
• The reel is assembled and the special button is pressed;
• Then the line itself starts to coil in the desired direction.

Always remember that the cutting thread must be protected from hard things. This will extend its life.

If you don’t adhere to this rule, you will often have to stop work, remove the spool, and replace the thread with new thread.

How to change the line on the trimmer?

How to replace fishing line trimmer for grass with step-by-step instructions allows even an inexperienced in such matters lawn mower owner to perform sufficiently difficult work.

However, before starting work on replacing the fishing line on the trimmer, it is necessary to ensure the safety of the work. In particular, care must be taken to prevent the mower from being switched on accidentally or inadvertently:

• prevent spontaneous start-up,
• remove the battery (if used),
• place the tool on a convenient place for work.

Grass trimmer fishing line replacement works comfortably when the mower is lying on the table and the person who does the grass trimmer fishing line replacement has an opportunity to get close to the tool from any side.

Grass trimmer head cover removal

The first stage of disassembly is removing the grass trimmer head cover. On an example of models of trimmers “Black and Decker” and others, for removal of a cover it is usually enough to apply some pressing force to squeeze the latch-fixator, which are located on the side of the head.

On some models of lawnmowers initially provides for the dismantling of the grass trimmer head, for which the hexagonal key included in the tool kit is used. The head is normally held by two or three screws, which are accessed through the side holes in the back cover.

The head cover, where the line spool is mounted, is usually held in place by a latch tab. It is enough to squeeze the tongue-latch with some effort and slightly turn the cover, after which the cover is easily removed At the moment of squeezing the tongue-latch should be slightly turned and lift the cover of the grass trimmer head to remove the winding drum.

Step two: Remove the filament drum (spool) with the line

The next step of the process is to remove the spool with the line from the inside of the head. Turn the head with the open side to see the line and the spool. On the side of the head find two recesses (eyelets) through which the line is led out.

Release the line from the holes by turning the drum. Then carefully remove the spool from the head area. The spooling reel of some models is mounted on a spring. This must be taken into account during the extraction operation.

Procedure for removing the grass trimmer spool with fishing line from the inner area of the head: 1. head complete with spool; 2. extraction carefully with a small axial turn; 3. extracted parts The old fishing line is completely removed from the spool. To perform removal of the old grass trimmer line, you need to remove the line from the loops-fixators and pull the free end. This method removes all old winding. The same process is repeated on the second section of the reel. It is recommended that the technician wear gloves when carrying out the work.