How much lubricant is needed in the perforator.

How much lubricant is needed in the perforator

Each tool needs timely maintenance, and the perforator is required first. After all, the work of this tool is accompanied by many reciprocating rotations and movements, while the volume of dust secreted from the working facility has a huge concentration. With these operating criteria, painstaking care for the device and timely replacement of lubrication in the punch gearbox are required.

Most of the users are sure that if the lubricant is located, then you can work with it an indefinite amount of time. This worldview usually exists among users due to the disgusting level of knowledge of the laws of physics, therefore we will tell you about the principle of lubrication in more detail.

Features of the selection of lubricant for the gearbox, drill, cartridge

Lubrication is a substance designed to reduce the friction force between the details interacting with each other. Of course, friction is partially left, and when operating the tool, in contact of structural elements continue to wear out. But in the presence of lubrication, the process is significantly slowed down compared to friction “on dry”.

Lubricants are synthetic, mineral and semi.Synthetic. The second variety is made from oil. She quickly loses its operational characteristics, it is more often required to change.

The main parameter of lubricant is the degree of its viscosity. Manufacturers of perforators in the operating instructions for them recommend using a lubricant with a certain value of this characteristic to care for their tools.

Each brand of lubricants has its own technical characteristics that should be taken into account when choosing. To lubricate the gear gears, cartridge, and the barrel of the nozzle, only varieties of compositions suitable for processing these parts are used.

To lubricate the passage of the perforator, it is recommended to use gearbox oil. It is poured through a special hole in the case in the amount required according to the instructions. In this case, it covers the interacting details, filling out the crankcase. Punch oil should be a liquid consistency.

Also, the transmission mechanism is lubricated with special plastic compounds. But it must be borne in mind that not all equipment can work normally when using substances with such a consistency. If the gearboxes (partially or completely) are plastic, then it is possible to use silicone lubricant, for example: 220-R Silicone DBC or HVS-100 Silicone #3 from Huskey.

To reduce friction between the tail parts of the nozzles and cartridges, it is necessary to use compounds of a thick consistency, which indicate that they are intended directly for drilling. If there are no such, then you can use a graphite analogue. But he takes heat worse than a special composition. Thick varieties of silicone lubricants are also used for cartridges.

Recommended lubricants

Lubrication can be used as proprietary (from manufacturers of perforators, for example, Hitachi, Metabo, AEG, Bosch, Bosch, Interskol, Bison), and from companies involved in the release of lubricants (XADO, Ravenol, Shell and others). The most popular companies with a demanded product range are presented in the table below.

When using a tool, the quality of which is confirmed by a special certificate, only the lubricant of the products indicated by the manufacturer should be used. The use of other materials will lead to a loss of the possibility of warranty repairs and maintenance of a perforator.

Some may have a question: whether the lid is suitable for lubrication of the perforator? It is associated with the fact that this lubricant in terms of its characteristics is inferior to specially designed compositions from well.Known firms. Litol can be used, only it will need to be changed more often. The best grease option is the composition specified by the manufacturer. There will be no problems when using it, in t.H. With warranty service.

Features of the choice of oil

Before lubricating the Bosch perforators, choose the right oil. When buying it, you need to pay attention to viscosity. High.Quality compositions are expensive, but you should not save. For such an expensive tool as a perforator must be careful constantly. What types of lubrication and how much can be used indicated in the instructions. If there is no such information, the best composition will help you choose specialists of the outlet or service center. On sale there are universal compositions for processing various models of perforators.

Many prefer to use graphite lubricants, which have:

In the absence of lubrication, you can use a single lithol or solidol. But they cause slight inhibition of rotating details and help increase the heating of the tool during operation. It is advisable to buy a special composition in the near future, remove Litol and apply a new composition.

Before lubricating the drill drill, you need to make sure that the oil taken is suitable for it. The compounds used for gearboxes are not suitable for lubrication. For the latter, take more Liquids, They must fill the free cavities, completely cover the parts that contact each other. If there are plastic elements in the gearbox, silicone grease is used. It is suitable for processing cartridges.

The transmission mechanism is allowed to lubricate plastic compositions. But not all tools when using the means of such a consistency will work uninterruptedly. Thicker mixtures are suitable to reduce the degree of wear of tail nozzles. The packaging marks their purpose for drilling. In the absence of those, you can take graphite, but they take heat worse.

Electric tool manufacturers produce their branded lubricants. They are also engaged in their manufacture by enterprises that specialize in the production of lubricating mixtures.

The most popular products of firms include:

• Bosch. For tail nozzles and gearboxes.
• Makita. For drilling.
• Interskol. For drills.
• Nanothek. For shanks.
• Turmogrease. Universal compositions.
• Lubcon Thermoplex. For gearboxes.
• Kress. To lubricate the drill.
• PRORAB. For processing seaming seats.

Lubricant for a perforator from brand Makita

How often you need to lubricate the tool

Depends on the intensity of using the tool Lubrication frequency. Each user must look at when to carry out processing. With daily operation, the parts need frequent lubrication (1 time in 3 months). When working with a perforator several times during the week, enough once a year.

What are the differences between bulk oil and packaged lubricants?

You need to know not only how to properly lubricate the drill of a perforator, but also a gearbox, cartridge, bearings.

In modern perforators there is a special oil pouring compartment. The instructions indicate the location of this hole and the disassembly scheme. The required amount of oil is poured into it, but before that, the crankcase is washed with gasoline or machine oil, well dried. In the absence of a special hole, the perforator is disassembled, blow.

In order not to confuse anything in the future, Dismantling is fixed. The procedure is started after cooling the tool. When applied chilled lubrication on hot surfaces, the electric tool will work with interruptions. Old grease is removed, since dust and metal particles are formed during the friction of the gear. If you do not clean and apply a new lubricant on top, the effect of such a prevention will not be. All the details of the perforator are carefully examined. Where there is no lubrication, you do not need to apply it. After application, they start assembly.

Lubrication extends the service life of parts and nodes

How to use grease for drill punch drills? If the knot is not lubricated, it will overheat and break, you have to buy a new equipment and repair the cartridge. Grease is applied to the grooves, which are fixed with stopping wedges. But at first they wipe the outer part with a napkin, removing dirt and dust. Enough for uniform application 1 g. Lubrication is carried out every time they change the drill or other equipment.

At the same time, you can process Cartridor oil seal, Then it will last much longer, and also the dust will not be able to get into it. But you need to know that only an open type cartridge is lubricated. If a closed system is installed in the perforator, the processing is not done.

The design of the tool is installed Sliding bearings, on which high loads occur. So that they serve as long as possible, lubricants are introduced to them.

Only the use of high.Quality lubrication helps to increase the life of the tool. For uninterrupted work, it is better to choose the compositions with which the manufacturer equips its perforators. The components necessary for this model of perforators are selected in them. Branded compositions protect parts from corrosion.

Than to lubricate the punch

Different types of lubricants are used to lubricate the gearbox and a cartridge with drill.

Lubrication for the gearbox

A special lubricant is used here, which should be called. Gearbox. It can be like under the brands under which the Perfs themselves are produced. Makita, Bosch, Aeg, etc.D. But it can also be released by a company that is engaged in this type of product, for example, Ravenol, Shell, XADO, etc.

Some use simple lilet or salutol for these purposes. But compared to special lubricating products, they dry faster, and they do not eliminate friction as it should.

Lubrication for drills

Everything is exactly the same here. Special lubricants for this purpose are called. For drills. And are also usually produced by the same firms that do punch.

For lack of special lubrication, you can use graphite. But it does not so well remove the heat from the shank, but this is important, since sometimes with prolonged work the shank happens and is flattened, which is why it is difficult to extract later.

How often you need to lubricate the tool

The tails of the nozzles should be smeared with each installation, having previously wiped dust or other pollutant. If the work is carried out intensively, then you need to visually control the degree of lubrication of the seat of the nozzle used.

The perforator works for different users with different intensity: some use it every day, while others only occasionally. Therefore, there is no unequivocal answer about the regularity of introducing or replacing lubricants. To decide on the need to replace lubrication in the general case, you need to FOCUS on the following:

• The intensity of the use of the tool;
• Recommendations set forth on this issue in the instructions for the perforator;
• Warranty service period.

That in the perforator should be lubricated

Proper maintenance of the perforator suggests that the user knows well what parts in it need to be lubricated and with what frequency. Note that this mechanism has a rather complicated device. We list its main nodes:

The gearbox is called the node that is designed to adjust the speed of the working nozzle. There is a closed performance of the gearbox. This approach is necessary in order to protect the details placed inside, from dust, dirt and all kinds of mechanical damage.

IMPORTANT! When the tool works, the gears are subjected to heavy loads. In this case, the friction between them increases greatly. This leads to the fact that the pace of their wear is increasing.

Usually all models of tools of the gearbox are lubricated immediately after manufacturing at the factory. However, during operation, the metal of parts is destroyed. The operation of the device leads to the formation of metal dust. She, when mixed with grease, leads to the fact that the friction force increases. As a result, wear is accelerated.

How to slow down the destruction process? It is only necessary to replace the lubricating material in a timely manner.

And let’s not forget that often inexpensive models are originally lubricated very badly. Or for this they use low.Quality material. They are recommended to smear again. Immediately after I bought.

Not only the transmitting mechanism is subject to lubricant processing. It is also necessary to process the cartridge and the seat of the change of nozzle, which is inserted. The cartridge is supplied dry. In it, it is necessary to smear only the area that is in contact with the tail of the nozzle. It is here when the tool is operating strong friction.

IMPORTANT! If you do not reduce friction, then this wear of the cartridge increases greatly. Up to the point that it will be damaged very much. The tail of the nozzle also wear out quickly. She is subjected to deformation, since during the strong heating caused by friction there are shock forces.

What parts in the perforator are lubricated

For proper maintenance of the perforator, it is necessary to know what details in it must be lubricated. At the same time, it is very important to consider the frequency of lubrication. This mechanism has a rather complex device. We list the main nodes:

Reducer is a node that is responsible for adjusting the speed of the working nozzle. Its closed performance has its purpose: to protect the parts placed inside from dust, dirt and mechanical damage, which are also possible.

IMPORTANT! When the tool works, gears are subject to large loads. In this case, the friction between them increases significantly. This leads to the fact that the pace of their wear is increased.

Usually in various models of tools, a gearbox is already greased from the factory. However, when the device works, the metal of each part is destroyed. This leads to the formation of metal dust, which, when mixed with grease, leads to the fact that the friction forces increase. So, wear is accelerated and.

How to slow down the destructive process? Carry out timely replacement of lubricating material.

Be sure to keep in mind that often inexpensive models are originally lubricated very badly. It also happens that they are lubricated with low.Quality material. They need to be smeared again. And immediately after I made a purchase.

Not only the transmission mechanism, but also the cartridge, but also the seat of the interchangeable nozzle, are subject to lubricant. The transmission mechanism is supplied with unexplored. It will need to smear only the area that is in contact directly with the tail of the nozzle. After all, in this place, when the tool works, severe friction occurs.

IMPORTANT! If it does not reduce it, then this cartridge will begin to wear out quickly. And this will follow severe damage. The tail of the nozzle is also quickly erased. It is gradually deformed, because with severe warming up due to friction, shock forces affect it.

Lubricant for Makita perforator

Japanese corporation, which has been engaged in the production of various construction tools since 1915. The very first owner of the company was Masaburo Makita, in whose honor the company still bears its name. To date, the corporation is one of the leading manufacturers of power tools (350 types) and accessories (4500 varieties) to them.

How to disassemble and lubricate the punch Makita video

Assortment of products (lubricants):

• “042005-4A”. For SDS perforators (packaging 16 kg);
• “042024-0A”. For the SDS punch reducer (packaging 2.5 kg);
• “P.08361”. For reducers of SDS Max perforators (packaging 30 grams);
• “183477-5”. For SDS perforators (packaging 30 grams);
• “181573-3”. Lubrication for drills (packaging 100 ml).

Bosch punch grease

• The founder of the German concern was Robert Bosch, an engineer and businessman, who in 1886 opened a small company for the sale and manufacture of electrical equipment. And despite the fact that initially the staff consisted of only one mechanic and one electrical engineering, the company was able to reach unprecedented heights.
• Today is a leading supplier of various categories of construction and consumer goods, including power tools. The subsidiaries of the enterprise are located around the world, including the Russian Federation. And, perhaps, in every city of Russia there is an official Bosch service center, and since 2007 a plant was opened for the production of equipment in the city of Engels.
• Many technologies, which are considered innovative today, have been successfully tested for many years in this company. Bosch tools are a reliable and ergonomic technique with the most advanced achievements. The policy of the corporation is not to sell as many tools as possible, but that each purchased apparatus serves as long as possible. That is why specially designed branded tools for maintaining power tools, including perforators, began to produce.
• “1615430009”, “1615430010”. Lubricants for inserted tips of the tools (packaging 30 ml);
• “1615430012”. Oil for perforators (packaging 1 l);
• “1615430014”. Lubrication in tubes for perforators (packaging 45 ml);
• “1615430015”. Lubrication in tubes for perforators (packaging 225 ml);
• “1615430016”. Grease for perforators (packaging 1 kg);
• “1615430019”. Grease for perforators (packaging 1 l);
• “1615437509”, “1615437511”, “1615437512”. Grease for perforators, complete with a sealing frame (packaging 50 ml);
• “3605430008”. Hydraulic oil (packaging 1 l).

Lubricant for labCon perforator

• German company founded in 1980 in the city of Frankfurt. Produces various types of synthetic lubricants for power tools. Products are supplied around the world, including Russia. The company positions its products as environmentally friendly compositions. For their development, only components are used that meet the highest requirements.
• Lubrices are distinguished by special thermal stability, they do not oxidize and perfectly prevent friction even with maximum load. These are waterproof compositions that guarantee the durability of the majority of power tools.

Assortment of products for power tools:

• “LubCon Thermoplex Aln 250 EP”. Grease for gearboxes;
• “Lubcon Thermoplex Aln 1002”. Grease for perforators;
• “LubCon Turmogrease NM 4602/0”. A universal composition for lubrication.

Lubrication for punch nanoeche

The Russian company is engaged in the production of synthetic, semi.Synthetic, mineral, semi.Liquid and plastic lubricants. For the first time in the Russian market, products under this brand appeared in 2004 and since then Nanonet has been increasing the range of its products annually. Lubrication and oil meet the high requirements of our time.

Lubricant for Metabo perforator

• The company first began its activities in 1924, Albrecht Schitzler and Julius Klos are considered its founder. The initial plans of the creators of the company were to release tools that would meet the increasing needs of modernity in a technological plan. Initially, the tool was manual, and only in the 30s of the 20th century they began to make electrical apparatus.
• The company is trying to make products that would have been durable. And for these purposes they create a whole line of electric tool care products, including lubricants for perforators. Most often these are plastic products, designed for shanks of drills.

Lubrication for the punch of the bison

The company is a Russian manufacturer of various materials and tools that have proven themselves to both domestic and foreign markets. The goods have an affordable price and good quality, the assortment range is constantly replenished with new categories of products. All products are tested in the laboratories of the company and only after their successful completion do they enter the design bureau. The finished product is mandatory undergoing quality control, and then, goes on sale.

• “Zubble.Expert 60”. Grease for drill (packaging 60 g);
• “Zubble Expert 125”. Grease for drill (packaging 125 g);
• “ZSB ZSB”. Lubrication for drills (packaging 125 g).

Enches

Russian enterprise, today is one of the leading domestic manufacturers of power tools. The company has extensive experience in the development and production of various products and has its own design and test office. The factories are located in Russia and Spain, and the products themselves are supplied to many European countries.

How to lubricate the punch gearbox and how to do it right

Perforator is a power tool that is designed to perform shockwork. To increase the service life of the power tool, you will need not only to use it for its intended purpose, but also to care for it correctly. To do this, you need the corresponding lubricant for the perforator, due to which the resource of the aggregate increases. When choosing lubricants, it will be necessary to consider that different parts of the equipment in question require appropriate lubricants.

Typically, power tools are maintained in autumn or spring, when a long leave for the device occurs or its preparation for the next season. To diagnose the power tool correctly, you must first figure out what parts on the perforator need to be lubricated. Structurally punch. A complex device consisting of a number of the following elements:

• The case is the basis of the tool inside which all the components are placed
• The electric motor is the main unit that drives the executive body of the tool. The cartridge. Puner engines have a horizontal and vertical location
• The piston system is an integral part of the gearbox, which is responsible for the formation of shock actions
• Cartridge. Has a special mechanism with quick fixation of the working nozzles
• Reducer is a mechanism that transfers rotational movements from the electric motor shaft to the tool cartridge. In the design of the gearbox there is a “drunk bearing”, which creates shock movements transmitted to the piston system
• The safety mechanism in the form of a coupling, which limits the rotation of the cartridge when jaming the working nozzle, thereby excluding the overheating of the motor
• Working nozzles are auxiliary elements that are installed in the design of the tool cartridge

To imagine what the perforator consists of, below is the diagram of the power tool.

Knowing the design of the tool under consideration, you can figure out what details of the perforator need grease. First of all, the reducer node needs a punch, the main purpose of which is to regulate the speed of rotation of the working nozzle fixed in the executive organ (cartridge). When working the tools, the gears experience large mechanical loads, which helps to increase friction. The lack of lubricants leads to an accelerated wear of the gear.

To increase the operational resource of the mechanism under consideration, you will need to regularly not only add grease to the reducer structure, but also pre.Remove the remaining old lubricants. Why is there an outdated lubricant for a perforator, not many know. It needs to be removed in order to clean the metal particles and dust, which are formed during the friction process of the gear. If you do not clean the old lubricant and apply new lubricants on top of it, then the effectiveness of such a diagnosis will be zero.

It is interesting! In the process of developing the gears, an increase in metal dust occurs, which negatively affects the operation of the parts, since due to it the friction force increases, which means that heating increases and wear is accelerated.

The gearbox or transmission mechanism in the perforator is lubricated from the plant, but you need to change the lubricant every year with the daily use of the unit. In addition to the gearbox, the tool also needs a cartridge and the seat of the installed nozzle. A drill (tail part). The cartridge (its inner part) is not lubricated from the plant, so the owner of the tool needs to be worried about this if you want to use the unit for a long time. In addition to the inside of the perforator cartridge, the shank of the installed nozzles also needs lubrication.

There are still sliding bearings in the design of the unit. They are also tested for heavy loads, therefore, in order to increase their service life, when conducting diagnostic procedures, it is necessary to add lubricants to the design of the bearings.

It is interesting! Few people know, but to improve the work of the tool, another tool knot also needs a lubricant. A collector.

What it is

A punch grease is a viscous oily substance of a yellowish tint with a specific smell. Why is it needed? Its main function is to reduce the friction force that occurs in the process of working between moving elements of the device.

The lubricant during the operation of the tool is saturated with wear products or mechanical dust, which reduces its viscosity. Therefore, periodically the composition must be applied again.

Lubrication deficiency in most cases leads to overheating of the device and subsequent breakdown. However, with the excessive application of the oily composition, the speed of rotation of the drill is reduced, and this negatively affects the general operational characteristics.

Lubrication of the gearbox and drill for the perforator: proper care for the tool

The grease for the perforator allows you to extend its service life and make its use more efficient. In order for the effect of the lubrication to bring the expected results, when choosing it, you should take into account not only the characteristics of the lubricant, but also the technical parameters of the device for which it is planned to use it. When choosing how to lubricate the punch, one must also keep in mind the fact that various parts of such equipment need different types of lubricants.

Proper lubrication of the punch gearbox

There is an opinion that the presence of grease on the mobile elements of the perforator allows you to postpone its replacement for a long time. Meanwhile, this opinion is fundamentally erroneous, and in order to change it, it is enough to get acquainted with the principle by which lubricants work.

Why do elements of the punch need a lubricant

Lubrication, including the punch, is a viscous substance, the use of which is necessary to reduce the friction coefficient between the elements of the design of the mechanical device moving relative to each other. Thus, the lubricant only reduces friction, but does not completely eliminate it, so the lubricant is gradually saturated with the products of wear of rubbing parts. Metal dust. As a result, not only the viscosity of the lubricant changes, but it itself becomes the cause of more intense wear of equipment.

Over time, the lubrication is polluted and loses its properties

How to choose a lubricant for a specific perforator model? First of all, you need to consider the recommendations of the manufacturer of equipment, which necessarily indicates both the required type of lubricant and the frequency of its replacement. It is especially important to FOCUS on such recommendations, has not yet expired the warranty period for the perforator. Otherwise, in the case of a breakdown of the device, you will not be able to use the warranty obligations of the manufacturer.

Many owners of perforators after the expiration of the warranty period begin to use not proprietary compositions for lubrication, but their cheaper analogues. Lidol or solidol. Of course, such lubricants are not able to harm the elements of the design of the perforator, but, using them, it should be borne in mind that they should be replaced much more often.

Gear lubrication

The punch gearbox is the most difficult device in design, so it requires special attention. It is not so difficult to perform the grease of the punch reducer, but the independent assembly of the pre.Disassembled node can cause serious difficulties. If the perforator is still under warranty, then it is best to contact a specialized workshop with the question of lubricating its gearbox, which provides warranty service for such equipment.

The detailed scheme of the device of your perforator will help to understand the mechanism and correctly assemble the tool

If any warranty obligations or the warranty period for your equipment have already expired to the perforator, the owner of which you are, and the authorized service center is far enough, you can independently lubricate the gearbox, observing maximum accuracy and attentiveness. You will need this:

• A set of locksmith tools with which you will collect and disassemble the punch gearbox;
• Pure rag;
• The composition itself for lubrication.

“Native” lubricant for the gearbox Makita P-08361. Refueling with the initial assembly of the tool and is recommended for maintenance

It is better if a corporate remedy specially designed for equipment of a certain brand is a lubricant. So, it can be a lubricant for a Makita perforator or a lubricant for Bosch perforator. If you do not have branded lubricant, but it does not work to purchase it, you can use inexpensive domestic lubricants.

It is very important that you have an instruction for a perforator that you are going to lubricate. Naturally, if you are the owner of the punch of Makita or Bosch, this should be the instructions for the technique of these brands.

All the details of the gearbox should be completely cleaned of the old lubricant

Having carefully studied the instructions for the perforator, you can proceed to the procedure for lubricating its gearbox.

• Before disassembling, the punch should be cleaned well of dust.
• When performing the disassembly of the gearbox, it is advisable to immediately remember how the elements of its design are located in it. At the same time, it must be borne in mind that to disassemble and lubricate the gearbox immediately after the end of use of the perforator is not recommended. This is explained by the fact that still hot parts of the gearbox when a cold lubricant gets on them can lose their physical characteristics.
• After all the components of the gearbox are extracted from its case, they should be thoroughly washed with gasoline or spindle oil and wiped dry.
• The inside of the gearbox body must also be washed, wiped (as far as possible) and let it completely dry.
• When disassembling the punch gearbox, you can pay attention to the fact that on some elements of its design there is no lubricant. This means only that such details do not need lubrication and there is no need to apply it to them.
• As mentioned above, it is better to use proprietary lubricant for a drill gearbox or a perforator, which differs a number of advantages. In particular, branded lubricants retain their initial characteristics much longer, so they can be used much less often. In addition, the corporate lubricant has such an important quality as water resistance, so it effectively protects the metal parts of the perforator from moisture and, accordingly, from corrosion. As a good alternative to proprietary lubricants for a punch or drill gearbox, you can use Metabo oil, the cost of which is quite affordable.
• After lubrication of all elements, the gearbox must be carefully assembled, observing the reverse sequence.

Which lubricant is better to use for a perforator

A good perforator is quite decent, and at the same time saving on lubrication is really unreasonable. And the household drill with the function of the perforator requires good maintenance. Therefore, it is important to choose the right, what kind of grease you will lay in your perforator.

Over, it is not necessary to do this more often than once every half a year for a household tool.

You can choose a lubricant as a performer of a perforator, such as traditional Makita, Bosch, Metabo but also from AEG, HITACHI, IntERCOCKOL, BEA.

You can choose a lubricant from lubricant manufacturers, such as the lubricant known to many from XADO, Ravenol and others. Some experts, having a small park of power tools, and having tried some species, came to the conclusion that the lubricant that is used to lubricate the nodes in Toyota cars is best suited. This is a multi-purpose lubricant 08887-00101 Grease MP-G No. 2, which gives very good results specifically for the work of punch. The question is how to buy it.

The table more clearly shows lubricants from well.Known companies.

Litol. 24 can be used, but, as indicated in the article, with reservations.

The composition of the lubricant must meet the following requirements:

• The lubricant should stay well on the details and when working on them there should be a lubricant.
• If the tool is working in a wet room, when the tool is turned off and its cooling according to physical laws in the gearbox itself, low pressure is set and moist air as a result of this goes inside. Therefore, lubrication should be resistant to moisture and not form an emulsion.
• Heating of grease during operation, followed by its thinning, should not affect the quality of the lubricant and restore their properties after cooling.
• A property such as a droppings should withstand a high temperature.
• The lubricant should remove dust and abrasive from the place of contact of the parts on the walls of the case.
• Since the details in the case are made from different materials, for example, steel, aluminum alloys and others, lubrication should be suitable for all.

As a novelty, you can pay attention to such a lubricant as “Ultra”, which with a slight increase in temperature becomes liquid. At the same time, it has excellent adhesion.

Ultra lubricant, which can be used both sealed and leaky gearboxes.

When buying a lubricant, of course, very carefully read the instructions, and sometimes reviews for this product.

Service of the perforator

Like every tool, the perforator needs to have the right care.

The tool does not belong to the category of cheap, therefore, on time, the maintenance made will allow your tool to serve for many years. Over, the punch requires this more often than any other tool. Remember in what conditions this tool works. Dust, vibration, nozzle bite into concrete or brick reciprocating. Progressive movement.

As mentioned above, the internal details of the gearbox need lubrication so that there is no friction between them. At the same time, lubricating them once, this is not enough. Particles of dust fall into the oil through the technological holes, and it itself becomes different, while the dust in it becomes as if an abrasive, which helps the Rapid wear of details. Therefore, so that the tool is longer in working condition, it must be periodically inspected and greased.

Therefore, when buying equipment, it is necessary to carefully read the technical documentation, which necessarily indicates which grease is preferable to use and how often to do maintenance.

If the perforator was bought through a dealer network or in a store that has an appropriate certificate, the lubricants that are indicated in the documentation must be used during the warranty. You can also conduct maintenance in one of the places from the network of service centers.

A technical inspection must be carried out in cases where the instrument smells unexpectedly burned rubber, unstable work or short circuit, as well as the appearance of unusual sounds. This will be a reason to immediately contact a warranty workshop or to examine the equipment yourself.

At the end of the warranty period, you can choose or continue to use this proprietary grease or buy cheaper analogues.

If China has been bought, which does not mean initially that it will immediately break as if lucky, but it may not have a maintenance centers and guarantees also have a guarantee. Therefore, you immediately need to tune in that you will serve and select a lubricant yourself.

Than to lubricate the punch

Different types of lubricants are used to lubricate the gearbox and a cartridge with drill.

Lubrication for the gearbox

A special lubricant is used here, which should be called. Gearbox. It can be like under the brands under which the Perfs themselves are produced. Makita, Bosch, Aeg, etc.D. But it can also be released by a company that is engaged in this type of product, for example, Ravenol, Shell, XADO, etc.

Some use simple lilet or salutol for these purposes. But compared to special lubricating products, they dry faster, and they do not eliminate friction as it should.

Lubrication for drills

Everything is exactly the same here. Special lubricants for this purpose are called. For drills. And are also usually produced by the same firms that do punch.

For lack of special lubrication, you can use graphite. But it does not so well remove the heat from the shank, but this is important, since sometimes with prolonged work the shank happens and is flattened, which is why it is difficult to extract later.

Lubricate the gearbox

You need to disassemble the tool case. Follow the points:

Now thoroughly rinse the gearbox itself, as well as the inner part of its body. Washing can be carried out, for example, with gasoline.

After that, first the most responsible parts are smeared. And then the entire gearbox is completely enveloped in lubricant.

Well, it remains to collect everything in the reverse order.

Lubricate the cartridge and shank drill

This operation is very simple, so its description will be quite short.

Just take a brown lubricant and add it directly to the cartridge. Another option involves applying it to the shank followed by installing it in the cartridge nest. But no one forbids to combine these two methods for reliability.

It is necessary to ensure that the lubricant is constantly present and as necessary to add a new. If you neglect this procedure, then the tail will overheat, which will either take it off from the rest of the drill, or to flattening. Therefore, do not be lazy and add.

That’s all you need to know by the cartridge and shank.

As promised, I attach at the end of the link to the video with disconnecting the switch:

This is all the information that I have on the question of lubrication of the perforator. I hope it was clear and affordable. I say goodbye to this. Until new meetings!

A few more recommendations on the grease of the perforator

The question of how often the perforator lubrication should be performed, users of such equipment occur quite often. There can be no unequivocal answer to this question, since the regularity of the lubrication depends on the intensity of using the perforator, as well as on what loads the equipment perceives. In addition, it is necessary to pay attention to the recommendations of the manufacturer, necessarily indicated in the technical passport, as well as whether the warranty period has ended for the device you use.

Hidden surfaces of the parts of the gearbox must be lubricated before assembling mechanisms

To the question of how to lubricate the perforator of one of modern models, it is much easier to answer, since the advantageous majority of these devices already have a special container in their equipment, in which you just need to fill the lubricant, unscrewing the drain cover and drain the old lubricant. Before pouring a new lubricant, the level of which should not exceed the control mark, it is better to blow the container using any compressor suitable for this, and then rinse using spindle oil or ordinary gasoline.