How much oil is pouring into a vibration poll. What kind of oil is poured into a vibroplate and how to replace it?

What kind of oil is pour into a vibro.Plate

The first replacement we strongly recommend doing after 5 hours of work. This is a prerequisite at the beginning of the operation of the snowman. The people are called the processing process, it is very important, especially in cases where intensive use is supposed. Daily, for many hours, under heavy loads, etc.D.

Further. Look at the passport. Ideally, there should be a technical table, which indicates the time frame. After how many motorcycles you need to replace the motor oil for the snowman. In principle, if there is such an instruction, then it describes the full maintenance necessary for the snowman.

But if it is not, then adhere to the rules:

• Oil must be changed every 50 hours with intensive work.
• If you do not have large volumes, and there are not so many snow, then you can replace at the end of the season.

The maintenance of the snowman, like any other equipment, must be carried out in a timely manner. Before starting, check the level of the probe. Remember that shortage of oil is work on wear, and moderately a greased mechanism will last several times longer.

The deadline for oil replacement, as well as its recommended brand, must be indicated in the device passport. If there are no instructions, adhere to the rules specified above. Basically, with moderate operation, oil can be changed once a season, or better consult with the service center or with me. In addition to the engine, do not forget about the gearbox, add grease in a timely manner.

What oil should be poured into the engine of vibration stations?

Before the start of work with vibroplitt, you need to pour oil into its engine. Remember that you need to check the level of oil before starting the vibrating plate. Otherwise, your technique will fail.

For engines on the gasoline of the brand Honda GX390, GX270, GX200, GX160, mineral motor oil viscosity SAE10W40 or SAE10W3.

There are also oils of other viscisons, but they may not be suitable in connection with the features of vibration equipment, which can also lead to engine breakdown. It is best not to conduct any experiments, but to use the oil that is recommended according to the instructions for using a vibrating plate.

How often you need to change oil in a vibration plate?

If there are no oil filters in the engine, then you need to constantly change the oil, since pollution appears in the process. You need to replace oil after the first twenty working hours, and then every time after 100 hours. Also, if you have not been used by vibrating plate for a very long time, it is worthwhile to replace the oil.

So, first, the equipment must be placed on a flat surface. Next, remove the lid from the hole where the oil will be flooded. Pour the oil to the indicated mark and close the lid.

Now you need to start the engine for a couple of seconds and immediately drown it out. We check the oil level again. If he remained the same as before the launch, then you can start work.

Service “Rent of Vibroopers in Minsk” will allow you not to worry about oil replacement: this will be done for you!

What oil should be poured into the engine of vibration stations?

Before the start of work with Vibropoplitt, it is necessary to fill butter In her engine. Remember that it is necessary to inspect the level of oil before starting the vibrating plate. In an unpleasant occasion, your technique will fail.

For engines on the gasoline of the brand Honda GX390, GX270, GX200, GX160, mineral motor oil viscosity SAE10W40 or SAE10W3.

There are also oils of other viscisons, but they may not be suitable in connection with the features of vibration equipment, which can also lead to a breakdown of the motor. The most perfect thing is not to carry out any tests, but to use the oil that is recommended according to the annotation for use by vibrating plate.

The following types of oil are used for vibration fuels:

For models on gasoline of brands such as Honda GX390, GX270, GX200, a mineral motor composition with viscosity SAE10W40 or SAE10W30 is best suited. These types of vibration oils have a large temperature interval, good thermo.Acidic stability. When using them, a minimum amount of soot is formed.

Synthetic oils differ from mineral mixtures at the molecular level. Synthetic elements molecules are synthesized with the given properties. In addition, they are able to wash all sediments on the details more quickly due to high fluidity. Mineral masses do it more slowly.

Choice

Before pouring the oil into the engine, vibrator and gearbox of vibration stations, you should familiarize yourself with its composition. You need to consider the viscosity of the mass. Various mineral products are more often used. Remember that the oil of inappropriate viscosity can lead to a breakdown of technology later.

Also, when choosing, you need to pay attention to the reaction of the liquid when the temperature factor changes. In this case, synthetic varieties react less to such changes, therefore during operation In conditions of sharp temperature differences, synthetic options are more often used.

Composition and properties

For vibration fuels that operate using gasoline engines, it is better to select special mineral oil. This product is the most natural of all varieties. The mineral composition for such oil is created on the basis of oil components by distillation and cleaning. Such a manufacturing technology is considered the simplest and fastest, so such mixtures have a low cost.

The composition of the mineral foundation includes alkaline elements and cyclic paraffins, hydrocarbons (cyclane, aromatic and cyclain-an aromatic). Also, special unsaturated hydrocarbons may include there. This type of oil will change the degree of its viscosity depending on the temperature regime. He is able to form the most stable oil film, which is good at good stability.

Synthetic options have a different composition. They are made by more complicated technology. In addition to the basic mixture, such varieties contain elements made of polyalfaolefins, aesters. The composition may also have semi.Synthetic components. They are 30-50% made of synthetic fluid. Some varieties of oils additionally contain various essential additives, detergents, anti.Intonate fluids, anti.Corrosion additives, antioxidative substances.

As in the previous version, the viscosity of the oil will depend on the temperature regime. But at the same time it is worth noting that the viscosity index is quite high. The mixture is also characterized by a low level of evaporation, a low coefficient of friction.

How the Lubricator works for pneumatic tools?

This device is a reservoir, the case of which is made of metal, put on on the inlet part of the pneumatic equipment and fixed on a threaded connection. When installing, the lubricator is placed after the filter, which is necessary to drain the air flow. After the air enters, it is enriched with oil particles and enters the tool itself.

It is very important that the distance of the hose between the lubricant and the device itself is no more than 10-12 meters: with a larger length, the distribution of oil with air is carried out not so efficiently, and condensation begins to form on the walls that reduces the productivity of the work. If such a length is not enough, it is better to use a linear.Type lubricators, which are installed immediately before the tool. Modern devices can differ in size, design materials and the volume of the funded capacity, where the oil is poured before work

In addition, devices can be single.Pointed or multi.Point, and the choice of equipment is made taking into account the features of future operation. Among other things, devices are divided into two groups according to the type of design:

Modern devices can differ in size, design materials and the volume of the funded capacity, where the oil is poured before work. In addition, devices can be single.Pointed or multi.Point, and the choice of equipment is made taking into account the features of future operation. Among other things, devices are divided into two groups according to the type of design:

• Liberties filters that are mounted on the very tool between its handle and hose for air flow.
• Air devices installed on the compressor or stream distribution system.

What kind of oil to pour vibropropels into a gearbox

Transportation of vibration stations

Here are a few requirements that must be observed during the transportation of vibration fuels:

• Be sure to check if the fuel valve is closed!
• Be sure to provide for lifting equipment in PT loading and unloading. The carrying capacity should be at least 50 kg more than the mass of the vibrating plate.
• The rise of the vibration plate is allowed only for a special eye located in the central part of the frame.
• Vibration fuels are transported in an upright position in order to avoid oil flowing.
• During the transportation, the vibration fuel must be securely fixed with belts behind the frame at least 4 points.

Help Transfer. Ceptkst website!

One. Where the group acts most regularly

B ) on the a a boat

That Frank is talking about a ship called The Seabird?

B ) Sank during the storm

3.What day Jimmy has a guitar game lesson?

You eavesdrop on the conversation of two people in a restaurant. Where did the woman just come from?

6.In the news you hear a story about a cat. Where they found a cat?

You hear a man talking to people at the beginning of the course. That its main point?

Nine.At the beginning of the radio filling, you hear how the girl leaves a message for her friend. Where is the speaker?

Ten. Photography from A to I will not interest experienced photographers, because

A ) Information is not suitable

Eleven. During his first flight, Jane is not alone

B ) Find out the White House she was looking for

12.You hear two people talking during a bus tour of the city. What do they agree with?

A ) How much the city is loaded

Thirteen. You hear a man talking on the phone about buying a house. What is the purpose of his challenge?

C ) To obtain information

Fourteen. Magazines differ from local newspapers due to

With ) What does it contain

Fifteen.When she studied at elementary school, Sarah

D ) He painted the scenes with a pencil

Sixteen. Jamie agrees to move to a new apartment

Eighteen.What happened to Jane during her test flight?

A ) She hit almost something

How to Change Oil in a Diesel

Nineteen. What people should do at the moment?

A ) stay away from the territory

You hear a woman talks about some news that she had just received. How does it feel about the news?

C ) a car

Frank quickly finds ships because he

A ) Reads books on history

23.How much does Philip pay for photography?

24.You hear two people to speak. How women feel?

What people should do at the moment?

Sarah makes enough money in her paintings for

C) Pay the materials of your artist

27.How the station is doing is different from other city sports halls?

At the moment, the shopping center is selling

C) birds are unlikely to be affected by farms

Thirty.Sarah makes enough money in her paintings to

C) Pay the materials of your artist

Why Steve and his group left their record company?

B) He wanted more control over the group Music

The host likes it Cooking for One. Because

You hear the man talks about the competitions that he enters his wife. What allowed him to do his favorite prize?

You turn on the radio and hear an excerpt from the music program. What did you learn about four people mentioned?

36.That, according to the woman, bad in holidays to Europe?

In his last television program John

What Roger recently worked at the zoo?

39.The first old ship found Frank was

You turn on the radio and hear the speaker’s man. What are you listening to?

You hear how the scientist speaks of a diet for weight loss, which is used by people who want to lose weight. What is she talking about a diet?

A) the results may come in handy.

How much the lessons of photos begin?

Roger believes that the best time for camping is

You hear a teenage girl tells about her hobby. Who is she talking about?

The first old ship found Frank was

One.Tom Critics call the best film actors for

What Tom considers the main thing in the style of the game of his parents?

According to Tom, what is difficult in the game of cruel characters?

C) the actor must make it clear to the audience

4.According to Tom, what is the task of the actor when reading the script for documentary?

B) to transmit the necessary information in the neutral manner

What is Tom in the end of the interview?

D) the desire to improve your own character

2. Rachel work artists

% PDF-1.3 % 947 0 Object Endobj Xref 947 71 00000016 00000 H. 0000003752 00000 n. 0000003854 00000 n. 0000004493 00000 N. 0000004536 00000 n. 0000004674 00000 n. 0000004814 00000 n. 0000004954 00000 n. 0000005355 00000 N. 0000005749 00000 n. 0000006353 00000 p. 0000006835 00000 n. 0000007160 00000 n. 0000007245 00000 N. 0000007577 00000 n. 0000007712 00000 n. 0000008276 00000 n. 0000008776 00000 p. 0000008803 00000 n. 0000008935 00000 n. 0000009113 00000 p. 0000009605 00000 n. 0000009869 00000 n. 0000010032 00000 p. 0000010643 00000 p. 0000010866 00000 p. 000001114 00000 p. 0000011151 00000 p. 0000011265 00000 p. 0000011377 00000 p. 0000013687 00000 p. 0000015859 00000 p. 0000019267 00000 p. 0000022090 00000 n. 0000024932 00000 p. 0000028762 00000 p. 0000031262 00000 p. 0000031555 00000 p. 0000032713 00000 p. 0000036569 00000 p. 0000039218 00000 p. 0000041205 00000 p. 0000041587 00000 p. 0000042792 00000 p. 0000043055 00000 p. 0000049814 00000 p. 0000065191 00000 p. 0000072769 00000 p. 0000072849 00000 p. 0000077813 00000 p. 0000077883 00000 p. 0000080499 00000 p. 0000080589 00000 p. 0000080900 00000 p. 0000081060 00000 p. 0000081509 00000 p. 0000081918 00000 p. 0000082204 00000 p. 0000082328 00000 p. 0000082467 00000 p. 0000084159 00000 p. 0000091333 00000 p. 0000091400 00000 p. 0000105088 00000 n. 0000105155 00000 n. 0000128755 00000 n. 0000128822 00000 N. 0000131824 00000 N. 0000131909 00000 n. 0000131980 00000 n. 0000001716 00000 n. Trailer] / Back 2653192 Startxref 0 %% Eof 1017 0 Object Stream H ޔu TS GNC T ؈! 0 mӏ |] bef.-GU) CAQ] P 9

What oil should be poured into a motorcycle fork?

In most tourist motorcycles, it is recommended to use 10W oil, and in sports and powerful city bikes. 2.5–5W. It is forbidden to fill the usual engine oil in the fork, since it allows you to get the desired damping characteristics.

As a shock absorber fluid into this fork, you can pour ordinary M8V1 motor oil (in the summer, of course), or something similar, in an amount of 200 cm/cubic meter in each feather. Oil replacement in a new fork should be condemned after the run of the first 500 km, following after 1,500 km, and then every 2000 km.

Operation of vibration fuels

In this article, we will try to examine in detail all aspects of the operation of such a type of construction equipment as a vibrating plate.

Usage Vibroophytes can be decomposed into several components: long.Term storage, transportation, active use. The largest number of actions, which is logical, will need to be performed with active use of the vibration plate, so we divide this stage additionally into: pre.Shock training, starting/stopping vibration fuels and periodic maintenance.

Most vibro.Fuels in the market have approximately the same structure, so in this article we will consider the average vibrating plate. Reverse vibrating plate with a gasoline engine weighing 200 kg. (for example: Wacker Neuson BPU 3050)

Maintenance of vibration stations

The frequency of maintenance of components and assemblies of the vibration stations are presented in the table:

How to choose oil for vibration plate ?

Each vibro.Fuel has two internal mechanisms at the same time, which require periodic control of the oil level. This is a vibration mechanism and engine. Before starting work, you should make sure a sufficient level of lubrication in these two systems. If necessary, it is worth adding a working fluid, however, it is important not to overdo it. If you take a vibration fuel for rent, you can be sure of the oil level, because the technician of the rental company constantly monitors the level of lubricants.

If you are worried about this issue as the owner of the viboroplit, it is worth knowing that in the vibrational system oil in fairly quantity is poured at the factory. Each manufacturer uses its own oils, so you can navigate the time for replacing this liquid only according to the attached instructions. It is preferable to carry out such an operation with the participation of specialists of the service center.

Taking the vibration fuel to rent, do not try to replace any fluids on your own-these parameters are controlled by the professionals of the Andor Company. You just have to replenish the fuel level. The need for oil valve to the motor can be discussed immediately when applying for equipment rental.

Despite the fact that the engines of Honda GX160-GX390 models operate on gasoline, only mineral lubricant materials of a shack-zone type with viscosity SAE 10W30-40 are suitable for them. Other viscosity indicators, the presence of additives, etc.D all this can lead to serious breakdowns of its own or vibration fuel to rent.

The thing is that this type of engine is not equipped with oil filters. This fact makes a periodic replacement of oil, gradually mixed with pollution, one of the most important rules for long.Term successful operation of the motor. In the new unit, the lubricant changes after the first 20 hours of functioning, and then every 100.

The Budget company offers the rental of vibration pins at the most favorable terms and at minimal prices. The technical condition, as well as the level of equipment liquids, is constantly checked by our masters, so you do not have to independently select consumables for the units. By ordering a vibration fuel to us, you will definitely receive a consultation about its operation.

How often you need to change oil in a vibration plate?

If there are no oil filters in the engine, then you need to constantly change the oil, since pollution appears in the process. You need to replace oil after the first twenty working hours, and then every time after 100 hours. Also, if you have not been used by vibrating plate for a very long time, it is worthwhile to replace the oil.

So, first, the equipment must be placed on a flat surface. Then remove the lid from the hole where the oil will be flooded. Pour the oil to the indicated mark and close the lid.

Now you need to start the engine for a couple of seconds and immediately drown it out. We check the oil level again. If he remained the same as before the start, then you can start work.

How often you need to change oil in a vibration plate?

If there are no oil filters in the engine, then it is necessary to change the oil all the time, because pollution occurs in the process. It is necessary to replace oil after the first 20 working hours, and later every time after 100 hours. Also, if a vibration fuel has not been used for a very long time, it is worth making an oil substitution.

Launching and stopping vibration placers

Often enough in light class vibro.Grade vibrations are consumed by the Honda GX series. On the example of such a motor, we will see the sequence.

Transfer the lever to the Close position (closed). If the engine warms up or the temperature of the air is the highest, then leave the damper open.

Sweep the throttle lever a little from the position of idle.

Switch the motor switch to position I

Make the engine with a hand starter. Pull the starter cable until you feel resistance, then sharply pull it over the entire length. Maybe it will be necessary to pull the cord a couple of times (3-5 times). The number of repetitions can be larger if the engine has not launched for a long time or a negative temperature outside.

After warming up the motor (1-2 min), smoothly transfer the lever of the damper to the Open position (open).

Translate the throttle lever (motor speed) into close to the greatest position.

• The throttle lever moves to the idle speed.
• The engine is turned off by moving the circuit breaker to the O.
• The fuel tap is locked.

The pre.Shit training of the vibration plate

• Familiarize with the annotation. The recommendation is naturally obvious, but specifically your equipment can own a certain feature, the ignorance of which can lead to a breakdown without proceeding to this work. Therefore, at least quickly, to get acquainted with the annotation all the same should.
• Checking the oil level. Any vibration plots and vibrors (except electronic) use motor oils. With the missing level of oil in the motor crankcase, you at least cannot start the engine (if the oil level sensor is installed), or the risk of destroying the piston unit. Before checking the oil level, set the vibrating plate in a horizontal position.

Checking the level of fuel. Here, attention should be directed only to the compliance of what you fill into the tank, what is declared by the manufacturer. After refueling, will certainly wipe all the fuel inks, t.To. They can be in unsafe proximity to hot details.

Air filter check. Because Vibroophytes Often they work in an environment with a huge dust, you need to watch the cleanliness of the air filter very often. As necessary, it must be cleaned with an air compressor.

The initial position of the vibration plate. Before starting the vibration fuel, you need to install on a sealing soil. Launching on a hard surface is not very recommended.

Transportation of vibration stations

Here are a few requirements that must be observed during the transportation of vibration fuels:

• Be sure to check if the fuel valve is closed!
• Be sure to provide for lifting equipment in PT loading and unloading. The carrying capacity should be at least 50 kg more than the mass of the vibrating plate.
• The rise of the vibration plate is allowed only for a special eye located in the central part of the frame.
• Vibration fuels are transported in an upright position in order to avoid oil flowing.
• During transportation, the vibration pound should be firmly launched with belts behind the frame in more than 4 points.

Vibroophytles are gasoline

Vibroophytus-one of the types of specialized equipment for road construction work-is designed to lay paving slabs, soil compaction, various types of bulk and coherent coatings: crushed stone, gravel, sand, asphalt. The most convenient machine for small volumes of this type of work. The vibration plate allows you to compile soil or road surface in those places where the skating rink is impossible, at limited along the sites: paths, trenches. Vibroopers are often used as a necessary addition to another usually larger type of road construction technique.

Vibration stations, being comfortable and economical, are widely used in various sectors of the economy: landscape design, road construction and repair, various areas of construction. Such machines can significantly reduce manual labor and significantly intensify the production of work.

All models are compact and adapted for numerous transportation.

Vibroophytes, unlike vibrors, have many times greater impact force.

See also: How to charge a car battery with a screwdriver from a screwdriver. How to charge a screwdriver with automobile exercises and is it possible

Splitztone vibro.Fuels accounts for 30% of the park of all vibration fuels of Russia.

Modernization of our vibration fuels and equipping them with a new folding handle allowed to ensure the placement of a pair of removable wheels on it. Now the wheels removed from the base are reliably attached to the handle and you can no longer worry about their search after work.

Technical Service of Honda engines

Technical Service of Honda engines on the technique of Splitstone.

3.5.5 Stop motorVibroophytles CO-310 Move the throttle. Close the fuel valve and drown out the engine using the switch, transferring it to position 0.

4.5.6 OperationVibroophytles CO-310 During the operation of the engine, the vibro.Plate moves forward in small and frisky jerks. Using the handle, control the movement of the vibration plate, circling it around obstacles and pits. The speed of the vibro.Plate is depending on the sealing material and the selected motor speeds. In particular, you need to be careful on the slopes. In these cases, the operator must be in a non.Hazardous position. At first, the soil is tightly compacted on top of the slope and only then evenly run to the seal of the bottom. The overstated humidity of the compaction base on the slopes sharply increases the danger when performing work. Vibro.Fuel passages in places with large stones and sharp irregularities are made at the least speed. Loading vibration stations for its transportation is done behind the sling eye.

3. Technical service and current repair of vibration stations co-310

To ensure reliable operation of the vibration fuel, subsequent types of maintenance are carried out:

• Daily technical service (EO)
• Technical service after every 100 hours. Work (then)
• Current repair after 900 hours. Vibroophytic work (TR).

With EO, you need to create an inspection of the vibration plate with a test of tightening of all threads of the threaded. The quality of care and maintenance significantly affects the durability and reliability of the vibration plate during operation.

Make a thorough motor service two or more times a year. Follow the tips of the manufacturer, clean the carpet from the cylinder head, inspect the input and output valves, clean and adjust the carburetor, inspect the ignition wire. On any day, inspect the engine for mechanical damage. Often inspect the tightening of the bolts. For more detailed instructions, contact the highly qualified personnel of the company R-Technic.

Once a day, inspect the oil level in the engine to work. Contact the special instructions for leaving the engine to highly qualified personnel of the R-Technician company.

When conducting then you need to do work on the EO. Disassemble, clean and lubricate what it remains to make our client client.

Remove the foam cartridge of the filter once and wash it in water with washing powder within a week. Having dried, apply him a little oil. The content of the filter cleanly extends the life of the motor and lowers the fuel consumption. If the work is done in dusty criteria, carry out the air filter service more often.

To lubricate the bearings of the vibrator inside, its body is flooded 200 ml. Transmission oil of the SAE 80W-90 brand. Excess oil during the operation of the vibration plate to flow along the axis of the Exentric shaft through the bolt sapun, for this, the skip is fixed. Therefore, the occurrence of an insignificant amount of oil on the lower pallet of the vibration plate is permissible. Control over the availability of oil in the vibrator to create no often than after 50 hours. Work of the vibration plate. As necessary, add the oil of the above brand (the introduction of oil of similar viscosity and properties is allowed).

In the presence of a centrifugal coupling, according to the instructions of the masters of the R-Technician company, you can choose the frequency of rotation of the motor shaft, in which it is required to cut a cuneiform transmission that transfers rotation to the vibrator of the plate. By twisting (or unscrewing) the necessary screws, we achieve such a compression of the springs when their efforts are not enough to delay a couple of cores of half.Meters with antifriction pads, with the frequency of rotation of the motor shaft chosen by the consumer. ATTENTION! The adjustment of the screws is suitable strictly similar, t.E. It is necessary to unscrew (in other words, twist) on a monotonous speed!

In industrial criteria, the coupling is configured for operation (transition to inclusion mode) at (2.7,000 ± 100) rpm. In order to increase the threshold of the trim of the coupling, t.E. If an even larger speed of rotation is required, in which the coupling is required, it is necessary to squeeze the springs, screwing the screws. Accordingly, in a working order, unscrewing the screws, you can reduce the threshold of the threshold of the coupling. When operating, the vibration plate should be watched that the centrifugal coupling does not slip, which leads to its sharp warm.Up, the wear of the rubbing parts and wear.

3.4Maintenance It consists in performing work on additions on incomplete disassembly and assembly of the vibration plate, to eliminate the defects found.

Our client remains the above work you are ready to perform highly qualified masters of the company group P.

What oil to pour into the Mazda three BL engine. Mazda engine oil three BL

The second generation of Mazda three BL was released in two thousand nine years, it was similar to the previous one. The platform remained the same, the body modification as in the previous generation sedan and hatchback, the wheelbase unchanged. The dimensions have grown a little, the weight decreased, the soundproofing improved, the salon was radically new. Depending on the configuration, it was possible to choose a progressive navigation system, a two-zone climate control, a leather salon with heated seats and the memory of the seats, a stereo system from Bose.

In two thousand eleven years, the car passed restyling, the bumper transformed, the fog lights became round, the radiator grille changed, the testimony of the devices became clearer. From two thousand twelve years, the car uses Skyactiv technologies, the model is equipped with a six.Speed automatic transmission and mechanics, new engines have appeared.

Original

Original oil for Mazda three second generation. Mazda Original Oil Ultra 5w30. Total releases this series specifically for the Mazda Auto Concert. Technical indicators of manufactured products fully comply with the requirements of the manufacturer. API SL / CF, SAE 5W-30, Acea B3 / B5 oils. These characteristics are suitable for both gasoline and diesel engines Mazda of the second generation.

The API class characterizes the year of production and the constructive level of the engine of the car, is divided into (s) gasoline, (c) diesel engines.

SL class is optimal for cars with a gasoline engine produced from two thousand one year. CF class is optimal for cars with a diesel engine produced from one thousand nine hundred and ninety.Four years.

The SAE class indicates the viscosity of the motor oil and its characteristics in certain ambient temperature ranges. 5W-30 determines a significant spread from thirty to twenty-five C. These figures indicate that the oil is all.Season. Acea class characterizes the operational properties of motor oil, shares the engines into (a) gasoline, (b) diesel. The number indicates the year when the category was introduced.

Second.Generation engines (2009. 2013):

• One.6 z6 (105 hundred and seven liters.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• One.6 Y642 (109 l.With.) the volume of oil 3.8 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• One.6 Y650 (116 l.With.) the volume of oil 3.9 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.0 PEY7 (158 l.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.0 LF-DE (150 l.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.0 lf17 (150 l.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.0 LF5H (147 hundred and fifty.One HP) oil volume of 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.3 l3-VDT (260 two hundred sixty seven HP) oil volume of 5.7 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.5 l5-ow (166 hundred and seventy liters.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5
• 2.5 L5-X (170 l.With.) oil volume 4.3 liters; API SL / SM certificates; SAE 5W-30; Acea a3 / a5

• One.6 Y642 (109 l.With.) the volume of oil 3.8 liters; API CF certificates; SAE 5W-30; Acea B3 / B5
• One.6 y601 (109 l.With.) the volume of oil 3.9 liters; API CF certificates; SAE 5W-30; Acea B3 / B5
• One.6 Y655 (116 l.With.) the volume of oil 3.9 liters; API CF certificates; SAE 5W-30; Acea B3 / B5
• 2.2 r2ff (150-185 l.With.) oil volume 4.3 liters; API CF certificates; SAE 5W-30; Acea B3 / B5
• 2.2 r2aa (150 hundred eighty.Five liters.With.) oil volume 4.7 liters; API CF certificates; SAE 5W-30; Acea B3 / B5

Analogs

Subject to compliance with the listed technical characteristics, you can choose an analogue from a worthy manufacturer. Consider the following options:

• Mobil Super Three thousand X1 Formula Fe 5w30 is a synthetic oil for gasoline and diesel engines, the API SN class (in our case, this class is newer than the second generation recommended by the manufacturer for Mazda, but can replace the previous classes). The viscosity of the SAE 5W30 matches the recommendations.
• Total the future NFC Nine thousand 5W30 The same company that produces the original Mazda Original Oil Ultra 5w30, corresponds to the permissions of the Mazda of the three second generation.
• Liqui Moly AA 5W30 engine semi.Synthetic motor oil for gasoline and diesel engines, API SN class, viscosity SAE 5W30.

When changing the brand of motor oil, it is recommended to rinse the system.

How to change oil in transmission on a scooter?

During the run.In a two.Stroke scooter, it is enough to add oil to gasoline at the rate of 1 to 30 with a completely good oil pump.