How to assemble a reel for a lawn mower. The coil does not spin

How to disassemble the coil of the lawn mower

In order not to make a mistake with the choice of a suitable trimmer line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter can be refueling, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wrap the trimmer line on the aiming of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

Trimmer line in a mower

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It contains two “paths”. Upper and lower. Between these paths there is a special partition with a notch. A trimmer line is wound on these paths. Previously, it must be stretched through the recess.

The aforementioned unit can be made by efforts and this article will tell you how to build a trimmer’s lawn mower with your own hands.

Replacement instructions. How to insert a trimmer line

It should be noted that the coils in mowers can be different:

For functioning with one osik;
For functioning with two antennae;
The trimmer line should be extended through the through hole, which is located inside the element.

And you should not confuse this part with an extension cord for a lawn mower on a coil, because despite the similar name these are two completely different elements.

This article will tell you how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here // MachinSpec.COM/Leszagotovitelnaya/Benzopila/Stanok-Dlya-Zatochki.Html, how to assemble a machine for sharpening chains of a chainsaw with your own hands quickly and simply.

In the first version, wound the cutting element is very simple:

On the inside of the coil element there is a fixing ear.
One mustache is inserted into it.
Refuel the nylon thread in the direction of the reverse rotation of the coil element.
You will need only 2 to 4 meters of trimmer line. When the winding process is completed, the small end of this cutting element is put out and fixed in the groove that is necessary to fix the trimmer line so that it does not spin during the functioning of the mower.
If there is no special groove, then the end should be held with a hand so that the cutting element does not spin during the further collection of the element.
At the last stage, it is necessary to pass the outer end of the thread into a special hole located on the outer part of the element. After that, the coil can be inserted into a mower.

When the video works with two ends of the polyethylene thread, then you need to take the following steps to tie the trimmer line into the lawn mower:

Inside, the coil will see how many recesses for winding are available (two or one). If one deepening, then both ends of the threads will be laid on this recess. If there are two of them, then the antennae are laid out separately. Each in its own recess.
It is necessary to rewind from 2 to 4 meters of polyethylene thread and pass two ends into the hole.
Wind both threads in one direction, reverse the drum.
When the entire trimmer line is wound, the ends should be fixed in grooves or held with a hand.
Both ends are threaded in the ear from the outside of the clip body.
After that, the drum is assembled and inserted into a mower.

Coil element or video can have a completely different design, different from the previous two options. The trimmer line can last through the ear, which is through and is located inside the coil. In this case, you do not need to disassemble the roller drum and manually wrap the plastic thread.

The polyethylene thread is threaded through the hole and rotates by pressing a special button. This The button is located on the case and is intended for the operation of the equipment, To be able to produce a trimmer line as it is worn out.

Instructions

In order to change the trimmer line, it is necessary to extract the old one (if it was).

The coil is a part of the trimmer structure, which is located inside the head of motorcycles, drum or bobin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Instructions on how to promote a hand head on a trimmer is described below.

First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
Now it remains to extract the old trimmer line and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the trimmer line, it is worth making sure that the thread suitable for the trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m trimmer line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the trimmer line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the trimmer line sits in the coil exactly.

The instructions for refueling the trimmer line in the coil is described below.

The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. There should be an arrow on it.
If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
Now you need to season the reel with a trimmer line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage the trimmer. At this stage, you need to charge the coil very carefully.
When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
Put the coil itself in the coil head, before that, extinguishing the trimmer line through the holes inside the drum.
Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the trimmer line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

How the head with a trimmer line on a motorcycle works why you need to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.Automatic and automatic). The instruction is presented above how to disassemble the head of the trimmer without a spring, t.E. On a manual.Type head. The principle of dismantling a semi.Automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.Automatic coil of the trimmer is as follows:

Inside the head is a coil, which is planted on slots that prevent its free movement
The coil is affected by a spring that presses it to the slots located in the design of the cover
The trimmer line, the length of which depends on the instrument itself. Usually this length is from 1 to 4 meters
During the work, if it is necessary to increase the length of the trimmer line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the trimmer line is wound from the drum, increasing in the length
Having released the required amount of trimmer line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a trimmer line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the trimmer line simply breaks down, without having a negative effect on the gearbox and the engine engine, as is the case in the case of metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the trimmer line into the coil of the trimmer. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

All about the replacement of trimmer line with a trimmer head

There are many types of heads that are designed for different types of trimmer line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this trimmer line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the trimmer line. The square has a good cutting ability, and despite the fact that such a trimmer line is less durable than round, on average it is consumed less. The square trimmer line quite easily cuts out the shoot of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good trimmer line that remained for the winter, in the spring suddenly behaves completely differently. It breaks, stops going out normally from the reel. There is a recommendation to soak the trimmer line in the water before work, but I do not see much sense in this, maleine anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on trimmer line for a long period of time, breaking or constantly torn trimmer line, which also does not want to leave the coil itself, can significantly complicate the work.

Preparation for the winding of the trimmer line

Previously, before the winding process, it is necessary to remove the coil with a trimmer line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

Such a model provides for the possibility of installing a knife. Removing the coil in such models is carried out by means of two keys drowned in the case. To install a trimmer knife, it is necessary to combine the hole of the bobin and rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the case is easy to unscrew with your hands clockwise.

How a starter or trimmer works?

Starter. The mechanism, as a rule, is unique and universal for lawn mowers, trimmers, gasoline and diesel generators. Equipping them even by car, motorcycle or scooter. Not a problem if your car has a free place to install it. It is not surprising that many Soviet cars and trucks were equipped with starting tools that vaguely resemble a double bent mountain.

The starting set consists of the following parts:

Hook spring;
The cord is wound around the coil;
Return the spring;
Drive ratchet and the main spring;
Ratchet case;
Stop bolt.

How to change the reel on the trimmer

Trimmer is the most common device for mowing grass and pruning small shrubs. This device is easy to maintain, thanks to easy weight, even women can cope with it. You need the right choice of cutting tools. The latest three versions use special cutting nozzles (discs, knives) or three.Dimensional heads with trimmer line inside. Nozzles and trimmer line are a consumable tool, but if the knives can be sharpened, then the trimmer line needs to be replaced. In this article, we will explain in detail how to replace the trimmer line correctly.

Types of trimmer heads

Inclined head for grass. This is the case when insertedcoil (Bobina) with a trimmer line worn on her (cord). This design can be installed on both gasoline and electric trimmers. The head clean is divided into 3 types.

Lawnmower Won’t Start? Watch This EASY FIX! AUTO- CHOKE PROBLEMS

Automatic. The cord is supplied after the user has reduced the engine speed. Although such rods have one drawback. Large consumption of threads.
Semi.Automatic. Using this type of head does not require complex manipulations from the user. The principle of their operation is arranged so that the device works at full speed. It is enough to slightly press the head of the trimmer into the ground, and thanks to the centrifugal force, the trimmer line is removed from the coil, after which it is cut to the desired length of the knife located on a protective cover.
Management. To lengthen the cord, stop the car, after which the line will be removed manually.

Based on the above, semi.Automatic coils are the most optimal. In addition, there must be single.Root and two.Row, which are used to mow high herbs and small with thin stem shrubs.

How to remove and disassemble a coil

Trimmer users need to remove and disassemble the coil. Think about how to do it.

A trimmer with a squinting head consists of several parts: a casing, springs (not all models), turns with a cord and covers.

A warning! It must be disconnected from the network.

In trimmers, 2 mowing options are most often used.

Option No. 1

To remove the head of the trimmer, let it go. Complete disassembly.

To remove the lid, click on the latches (latches) located on both sides of it.
Removing the lid, you will see a coil that needs to be removed from the body. In some coils, a spring is installed under the coil, which must be carefully pulled out so as not to lose it in the grass.
Stile, in the center of the case you will see a cross screwdriver or flat head. “Star”.
You need to unscrew the bolt (counterclockwise).
Having removed the mount, you can see in different directions, remove it from the gear shaft.

Option No. 2

In this format, the head spins on the gearbox shaft. Delete it Block the shaft. To do this, in three versions, for example, in the Huter and Champion devices there is a hole that can be inserted either into a thin screwdriver or into a metal rod.

So, to remove the coil, take 2 simple steps.

Insert the screwdriver into the hole and fix the shaft.
Get the body of the head and start twist it clockwise. This is due to the fact that the thread on the shaft remains.

Forest winding algorithm

Depending on the model used, the type, thickness and length of the line are selected. The diameter of the cord can be from 1.2 to 4 mm. He knows how to cut.

In extreme cases, universal scales of 2 mm are used.

There are 3 ways to find out which wood diameter can be used in the lawn mower.

Contact the instructions of the device for information about the thickness of the cord.
Look at the coil itself. Information on possible extensions of the line may be marked.
Insert the trimmer line into the outlet. If this passes through this, it can be used.

The line is wound on a coil located in a mowing head. You must open it first. There are two ways to wind the cord.

The first way

To correctly determine how many meters of wood must be installed on coils, it is necessary that their diameter does not exceed the diameters of the side sides. If you want to insert it into the case. As soon as you have decided on the length of the material, you need to load it into the reel.

Need Fold the trimmer line in half, it was 10-15 cm longer than the rest.
Please note that the bobbin is divided into 2 parts by the central side, with which charging begins. Catch it, use spells, make a little effort.
This is very important to determine, Field To the coil. If you want to see what you can find on the drum, then you can write an inscription with an arrow. There are cases when there is no arrow on the coil. In this situation, you can look at the arrow drawn on the head of the braids, and wrap it in the opposite direction.
We need to behave carefully, with maximum tension.
As soon as the cord is finished, the short end of the forests should be fixed first.
The other end, the one that is strong in the recess on the opposite side of the coil.
After fixing the line, cut its ends, leaving the allowances about 10 cm.
Next, you need to install the old coil in the mowing head. To do this, you need to install and raise holes in the weekends, place the hairpin in the casing, then apply the necessary force, pull the trimmer line from the fasteners and tighten it.
Now you can delete and record it using latches.

The second method

Some coils provide the second method of fixing the roots: you can charge 2 pieces of thread instead of one folded in half. Forest replacement is carried out according to the following algorithm.

As in the case when it is changed, it is discussed above.
Bend one end of the cord in the form of a hook.
Find the pin below with the hole for attaching the tree and insert it into the curved end of the loop.
On these arrows, it is necessary to wind the cord to the required level, which does not exceed the diameter of the coil.
Do the same for the second coil nest.
Hats are no different from the method described above.

Sources:

https: // 101benzopila.Ru/kak-razobrat-katusku-gazonokosilki/ https: // machinspec.COM/Kommunalnaya/Kosilka/Kak-Namotat-Slesku.HTML https: // zemlyaselhoz.Ru/kosilki/kak-namatyvat-lesku-katushku-gazonokosilki.HTML https: // GP-PRSMAH.RU/Brend/Katushka-Dlya-Sleski-Trimmera.HTML https: // prideSaratov.Ru/Selhoztehnika/Kak-Pomenyat-Slesku-Na-Trimmera.HTML https: // www.IVD.RU/Stroitelstvo-I-Remont/Instrumenty/Kak-Pomenyat-Slesku-Gazonokosilke-Podrobnaya-Innstrukciya-52011 https: // 101benzopila.Ru/kak-PRAVILNO-POSTAVIT-KATUSKU-ZAZIGANIA-NA-TRIMER/ https: // Estetika-studia.Ru/kak-Pravilno-Sobrat-Starter-Gazonokosilki/ https: // Veloelektro.Ru/kak-razobrat-katushku-gazonokosilki.HTML

Do.It.Yourself repair renewal repair: how to remove, disassemble, change the trimmer line, assemble and install back

Video instructions. He came to the cottage to mow the grass, began to mow, hooked a stone and a coil on the trimmer crashed, because of the coil to return to the city for a long time, and it is overwork, since you burn gasoline more than it stands, and I found a temporary solution. DIY trimmer repair involves the elimination of all malfunctions that the repair of benzokos with your own hands can be carried out if it starts and works on the idle is the main sign that the ignition coil was out of order and repair is required. Video: how to remove and put a reel on a lawn mower! The gasoline is manual. Replacement of trimmer line in a reel. Replacing a coil in a Chinese trimer. How to disassemble a trimmer coil.

If the trimmer line is not lengthened by a light blow of the trimmer button on the ground, the prerequisites for this usually the following.

Option 1. Snack, t.E. Clamping cord between turns. This problem usually occurs if the user wraps the trimmer line on the coil unevenly, crossing the windings or wrapping it without tension. In the latter case, when the mower rotates at high speeds under the influence of centrifugal force, the cord begins to drag on, under the influence of which the interspersonal clamp of the braid trimmer line may occur. To eliminate obstacles, you need to disassemble the coil on the trimmer and correctly rewind the cord, in other words, even rotates with good tension.

Option 2.4. Very short ends stick out of the head. When hitting the ground, the rod may not fall out if its ends protruding from the head are not long (short). Then centrifugal force is not enough to stretch the trimmer line. Therefore, it is necessary to hang the unit (turn off the engine in another way, disconnect the electric trimmer from the network) and pull the trimmer line manually, after pressing the button.

Option 3. Little line is sealed inside a mower. This makes the coil stop and do not even rotate when you press the button. This is mainly happening for several reasons: low quality of the cord, overheating of the coil during prolonged operation of the machine and the effect of a mowing trimmer line on hard objects.

First, the cord of third.Party manufacturers that you like is made of low.Quality and fusible materials that do not withstand mechanical and thermal loads. Therefore, it is necessary to give preference to “branded” fishing.
If you have a trimmer line of an unknown owner, and it is often soldered during operation, then, of course, follow the example of some users who, after filling the cord in the coil, moisten it or silicone lubricant (from a spray can) or mineral oil). This procedure significantly reduces the possibility of soldering turns of the mowing trimmer line.
The trimmer line can also be soldered if during the mowing it falls into a solid object (stone, fence, dry branch, etc. D.). During this time, it stretches a little and stretches to the head at high speed. The cord heats up from friction, and its coils stick together. The only thing that will be done to eliminate this problem is to open the trimmer coil and rewind the trimmer line.

There are situations when the Trimmer user notices very quick trimmer line consumption. Here he never pressed the button button to lengthen the trimmer line. A prerequisite for spontaneous lengthening of the trimmer line by cutting a special knife on the machine body is a lack of spring in a mowing head. Often beginner users of mowers, trying to load the trimmer line into the coil, forget to install a compressed spring in the head, in other words, completely lose it when opening the lid, and then they do not even suspect its existence.

The trimmer line also expands without using the button if the spring is weakened. If the spring check confirmed this fact, then you need to insert several goals under it to increase the characteristics of the pressing.

The owners of the trimmers, mostly beginners, in confusion, next to the panic, when the coil has to change the cutting tool or trimmer line. Often, when trying to unscrew the lawn mowing head, users simply make it unsuitable for use, not suspecting that it is unscrewed in the opposite direction To prevent this, if you need to change the tool, we recommend that you join the step.By.Step annotation below.

Before pouring the rod into the coil, turn off the engine bureau, as it is also called, de.Energize the electric trimmer to avoid injuries that occur when the cutting tool is accidentally turning.
Unscrew the attached nozzle of the transfer shaft. To do this, it is necessary to fix the shaft by leaving the opening on the puck and inserting an iron bar there or a screwdriver there.
Unscrew the nozzle. You should know that the thread on the shaft remains. Therefore, turn the trimmer coil to the right, in other words, clockwise.
Disassemble the mowing head. In most cases, the main cover is attached on the clips. To remove it, you will need to lower these clamps onto the case, squeezing the edges of the lid. If there is a pass, if your trimmer has an automatic mower with a button below, then the nozzle should be disassembled carefully, since there is a chance of a spring loss, which sometimes flies away when removing the lid. ,
Cut the required amount of fishing. Usually its length is 5 meters. Use the cord of the same diameter that is indicated in the note to the tool. It is not recommended to exceed the largest diameter of the mowing trimmer line, as this will increase the load on the engine and increase gas mileage.
Find the middle of a piece of cord, folding it in half. You will get a loop.
The coils are cut special grooves inside (there are holes). Insert the loop of the trimmer line into this groove.
Wind a trimmer line on a reel, turning it counterclockwise. The cord must be filled very evenly, the turns you need to put it in a non.Overlap and with good tension. After the winding is completed, leave the free ends of the trimmer line about 20 cm long and fix them in grooves on the sides of the coil.
Collect the mowing head. Do not forget to completely assemble the nozzle spring and washer (if available). Insert the coil into the housing and pass the ends of the cord through the holes or eyes.
Put on the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Turn the trimmer coil to the left (counterclockwise).

How to disassemble a coil from a lawn mower

Trimmer, whether it is gasoline or electronic, is the only right solution for mowing grass in inaccessible places with which the wheelbreak does not coage. As a cutting tool in trimmers, iron knives or a special trimmer line are used, which is tucked into the coil of the trimmer. Alas, often, trimmer heads during use during time become unusable. Some malfunctions have an option to remove on their own, and with some, a complete change of mowing head will come in handy.Cassyle heads for trimmers have various designs. Both ordinary and complex. The figure below shows an automatic trimmer head from the Husqvarna motorcycle (Khuskvarna) disassembled.

This type of head is in configuration of most benzocosyles and electrimmers, such as STIHL (Shtil), Patriot (Patriot), Champion (Favorite), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite common. It includes subsequent details:

The base of the mowing head;button for automatic supply of the cord;Spulk (coil), where the trimmer line is refuel;spring;eyelets. Through their trimmer line goes out;trimmer head cover;Field (cord).There are also more ordinary trimmer heads shown in the next photo.

These nozzles do not allow you to change the length of the trimmer line in automatic mode (after pressing the button). If the passage of the cliff of the cord, you have to stop the mowing and change it manually.

Electrimmer users and benzocos often face the inconsistency associated with an automatic mowing head. Coil malfunctions occur subsequent: A rather pretty element of the site is now the lawn. But it will look great if you care for him. To do this, often water the area, feed with fertilizers and cut the grass once a week. If you neglect the last condition, then the territory is rapidly rapidly. Trimmer at idle is spinning a head. DIY Benzokosa repair: analyzing defects and methods for eliminating a benzocosa is one of the main instruments of the summer resident used to briskly bring an earthen plot in order. Receive this weapon for mowing the grass on personalities and owners of personal houses. The period of active implementation of benzos and electric tr.

Trimmer, whether it is gasoline or electronic, is the only right solution for mowing grass in inaccessible places with which the wheelbreak does not coage. In the role of cutting tools in trimmers, iron knives or a special trimmer line are used, which is refueling in the coil of the trimmer. However, to chagrin, trimmer heads in the process. The trimmer line is not lengthened by automatic;the cord spontaneously leaves the coil.If, with a light blow, the trimmer coil button on the ground does not lengthen, then the prerequisites of this are subsequent.

Option 1. It came out snacking, t.E. Squeezing the cord between the turns. This non.Bond usually occurs if the user wound the trimmer line on the coil unevenly, with crossing the turns, or wound it with the missing tension. In the latter case, when the mowing head is rotated at huge revolutions under the influence of centrifugal force, the cord begins to drag on, under the influence of which you intervaling fishing. To eliminate the confusion, you will have to disassemble the coil on the trimmer and rewind the cord correctly, in other words, even coils with good tension.

Option 4.5. Very short ends protrude from the head. The trimmer line may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In such circumstances, centrifugal force is not enough for the trimmer line to stretch. Therefore, it is required to suspend the unit (drown out the engine or turn off the electritrimmer from the network) and pull the trimmer line manually, after clicking on the button.

Option 3. The trimmer line was soldered by the snitches. This leads to the fact that the coil stops does not spin when the button is pressed. Mostly, this happens for several reasons: the bad quality of the cord, overheating of the coil during prolonged operation of the unit, a string of trimmer line on solid items.

At the beginning of the cord of the advantage of manufacturers, you will like it made of low.Quality and fusible materials that do not hold mechanical and temperature loads. Therefore, preference should be given to “branded” fishing.If you still got a trimmer line of unknown properties, and it is often soldered at the time of work, then you can follow the example of certain users who, after refueling the cord, moisten it or silicone grease (from the spray can), or mineral oil). This procedure greatly reduces the possibility of soldering a trimmer line with each other.Also, the trimmer line can sleep if at one time of the mowing it hits a hard object (stone, fence, dry branch, etc.D.). During this, it is little stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are stuck together. The only thing that is performed to eliminate this malfunction is to open the trimmer coil and rewind the trimmer line.

There are situations when a trimmer user notices a very frisky trimmer line consumption. In this case, he never pounded the button on the ground for lengthening the trimmer line. The prerequisite that the trimmer line spontaneously lengthens, cutting off a special knife on the casing of the device, is the absence of a spring in a mowing head. Often, beginner users of mowers, trying to charge the trimmer line into the reel, are blurred to install the clutching spring in the head, or completely lose it when opening the lid, and then, do not even suspect its existence.

How to tie a trimmer line in a trimmer? So that the plot near the house always looks well.Groomed and careful, it often needs to be cut. Modern, modern technology allows you to solve this problem without unnecessary physical efforts. Electronic trimmers are so ordinary in management and care that even a child can be rodded with the help of them with the help of them. The main thing is to understand the wound.

Trimmer, whether it is gasoline in other words, is the only true solution for mowing grass in inaccessible places with which the wheeled lawn mower does not coage. In the role of cutting tools in trimmers, iron knives or a special trimmer line are used, which is refueling in the coil of the trimmer. But, sometimes, trimmer heads in the Protz.

How to disassemble a coil from a lawn mower

The base of the mowing head;button for automatic supply of the cord;Spulk (coil), where the trimmer line is refuel;spring;eyelets. Through their trimmer line goes out;trimmer head cover;Field (cord).There are also more ordinary trimmer heads shown in the next photo.

Electrimmer users and benzocos often face the inconsistency associated with an automatic mowing head. Coil malfunctions occur subsequent: A rather pretty element of the site is now the lawn. But it will look great if you care for him. To do this, often water the area, feed with fertilizers and cut the grass once a week. If you neglect the last condition, then the territory is rapidly rapidly. Trimmer at idle is spinning a head. DIY Benzokosa repair: analyzing defects and methods for eliminating a benzocosa is one of the main instruments of the summer resident used to briskly bring an earthen plot in order. Receive this weapon for mowing the grass on personalities and owners of personal houses. The period of active implementation of benzos and electric tr.

Trimmer, whether it is gasoline or electronic, is the only sure solution for mowing grass in inaccessible places with which the wheelbreak does not coage. In the role of cutting tools in trimmers, iron knives or a special trimmer line are used, which is refueling in the coil of the trimmer. However, to chagrin, trimmer heads in the process. The trimmer line is not lengthened by automatic;the cord spontaneously leaves the coil.If, with a light blow, the trimmer coil button on the ground does not lengthen, then the prerequisites of this are subsequent.

Trimmer, whether it is gasoline in other words, is the only true solution for mowing grass in inaccessible places with which the wheeled lawn mower does not coage. In the role of cutting tools in trimmers, iron knives or a special trimmer line are used, which is refueling in the coil of the trimmer. But, sometimes, trimmer heads in the Protz.

Top Reasons Lawn Mower Not Self-Propelling — Lawn Mower Troubleshooting

Replacement instructions. How to insert a trimmer line

It is worth noting that the coils in mowers can be different:

For functioning with one osik;
For functioning with 2 antennae;
The trimmer line should be extended through the through hole, which is placed in the snuffs of the element.

And do not confuse this part with an extension cord for lawn mowers on the coil, so as, despite the similar title, these are two completely different elements.

Mini chainsaws were created for easy work and people who prefer to keep the device with one hand.

This article will say for you how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here // MachinSpec.COM/Leszagotovitelnaya/Benzopila/Stanok-Dlya-Zatochki.HTML, how Collect a machine for sharpening chains of a chainsaw with your own hands is rapidly and simply.

The gasoline is manual. Replacement of trimmer line in a reel.

In the first version, wound the cutting element to pain is simple:

On the inside of the coil element there is a fixing ear.
One mustache is inserted into it.
The nylon thread must be refuel in the direction of the revolutionary rotation of the coil element.
It will come in handy from 2 to 4 meters of trimmer line. When the winding process is completed, put the small end of this cutting element outward and fix it in the groove, which is needed to fix the trimmer line so that it does not spin during the functioning of the mower.
If there is no special groove, then the end should be held with the hand so that the cutting element does not unwind during the upcoming collection of the element.
At the final step, you need to pass the outer end of the thread into a special hole located on the outer part of the element. Then the coil can be inserted into a mower.

When the video works with 2 ends of the polyethylene thread, then you need to take subsequent steps to tie the trimmer line into the lawn mower:

Snutri on the coil will be seen how many recesses are for winding (two or one). If one deepening, then both ends of the threads will be laid on this recess. If there are two of them, then the antennae are laid out separately. Each according to their own seizure.
It is necessary to rewind from 2 to 4 meters of polyethylene thread and pass two ends into the hole.
Wrap both threads in one direction, revolutionary rotation of the drum.
When the entire trimmer line is wound, the ends should be fixed in grooves or held with a hand.
Both ends are threaded in the ear from the outside of the clip body.
After which the drum is assembled and inserted into a mower.

To stick a trimmer line in a lawn mower, in which coil Contains two grooves, you need to use the previous option for refueling this polyethylene thread. In this case, any of the ends of the trimmer line will be wrapped in their own groove. All other acts similar to the previous process.

Coil element or video can have a completely different design, good from past 2 options. The trimmer line can last through the ear, which is through and is located. In this case, it is not necessary to disassemble the roller drum and manually wrap the plastic thread.

The polyethylene thread is threaded through the hole and spins by pressing a special button. This button is located on the case and is intended for the operation of the equipment, so that it is possible to produce a trimmer line as it is worn out.

Do not worry that the polyethylene thread is wound in the wrong direction, because it can spin exclusively in one direction in this design.

Necessary tools and materials

To make a lawn mower from a grinder or washing machine at home, you will need to stock up on the following tools, devices and additional materials:

Electric drill;
A grinder with metal disks or an electrolobian with saws on different materials;
Hammer;
Roulette or ruler;
Pencil or marker;
Vise;
Pliers;
Screwdriver;
As an abrasive stone or an emery machine;
Welding apparatus and electrodes to it (if you make welded metal connections, not bolted);
Wires;
Button on/disconnecting (taken from a grinder or washing machine);
Bolts with nuts and washers (preferably grover);
Metal corners or wooden bars.

Instead of a grinder or an electrician, you can use a hand hacksaw for metal or a wood saw with small teeth. It is also recommended as well Make a drawing homemade mechanism to have an idea of the final result, based on the details available.

Types of semi.Automatic heads

A semi.Automatic head head, as a rule, consists of a case, inside which several springs and a spool are located. Shpuli, in their execution, are divided into:

Many owners of household trimmers remake single.Sectioned spills for two.Section. To do this, you need to find a solid metal plate, and apply a circuit with a bursal diameter on it. After that, the plate is cut along the contour so that the thickness is located near the cord winding area. As a result, the resulting circle must move freely around its axis. Further on the resulting ring you will need to make a cut and put the spool inside the ring. Both parts must be interconnected using a tape or fast.Drying glue. As a result, the manufacturer gets a spool, a trimmer line in which can be wrapped in two sections.

How to wrap it up?

Knowing how the coil is disassembled can accelerate the process of replacing the trimmer line. It all depends on which structure the coil has and how many antennae. Turn the thread into the coil, which has only one working mustache, is quite simple, especially if you adhere to a sequential plan.

Depending on the parameters of the bobbin and the length of the trimmer line, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the trimmer line should be installed in the hole located inside the bobbin.

Next, the string should be wrapped on the drum. Over, this is done in the opposite direction from the usual rotation of the spool. Typically, on trimmers on the inside of the bobin there is an arrow that shows in which direction you need to wind up.

WEAK OR NO SPARK? DOES IT NEED A NEW COIL? / OLD MECHANICS TRICK TO FIX A MAGNETO IGNITION SYSTEM

Part of the trimmer line must be pulled out and fixed in a special puzzle located on the inside of the bobbin. Its purpose is to maintain winding when bringing a bobbin to working condition.

The end of the string must be put into the hole located on the outer part of the bobbin.

At the last stage, it is necessary to collect parts of the bobbin and put on the barpet on the bar.

Installing the trimmer line on a coil with two mustache in a slightly different way. First you need to determine how many grooves passes along the inside of the coil, on which the trimmer line is put. There are options with one groove, and then both mustache must be wrapped together. There are also models with two grooves, when each of the mustache goes along a separate.

In a model with one groove

The trimmer line must be stretched into the hole, and its mustache should be folded together and aligned.

Then winding in the direction opposite to rotation of the bobbin on a mower is carried out. Often there is an arrow inside the coil, indicating how to put a trimmer line correctly.

The ends of the string are fixed in special passes or simply temporarily adhere to with their hands and drawn into a hole located on the outside of the bobbin.

After that, the spool is closed and attached to the bar, after which the mitch is ready to work.

In the option with two grooves

The trimmer line is first folded in half to determine where the middle of the bend.

Further, the loop formed on the bend is threaded into the groove, which is formed between the two grooves.

After that, you can wrap both mustaches of the trimmer line on a separate groove.

You can fix the mustache and collect the coil in the same way as already described above.

For the first time open the coil and wound a new trimmer line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some coils have an automatic system that independently wraps the trimmer line. As a result, it remains only to correctly correct the end of the trimmer line, and everything is ready. In such models, the string must be put on a hole that is on the outer part of the case. Further, Bobina is assembled, and when the winding rotates, then there is a trimmer line on it.

Tips and recommendations on how to wind a trimmer line and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

Set the lid to clicks. Over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
Do not wrap the trimmer line with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
If you own the tool not with two conclusions of the trimmer line, but with one (usually low.Power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting!Choose the material of the appropriate quality so as not to get injuries when working with benzo.Cards, trimmers and motorcycles. In the process of beveling grass, small stones and other materials fall under the rotating parts that can fly over long distances therefore, despite the fact that the trimmer line is not a knife, work with the tool should be carried out in protective special uniforms. The result of the work done is as follows. After the replacement of the new material is enough for an area of up to 600 square meters, but when taking into account the presence of a reinforcing layer on the trimmer line. Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.Button grass with trimmer line, as there are special metal wheels or knives for this.

Sources:

https: // Tool-nd- Tools.Ru/Dlya-Sada/Kak-Razobrat-Trimmernuyu-Golovku.HTML https: // Veloelektro.Ru/kak-razobrat-katushku-gazonokosilki.HTML https: // Veloelektro.Ru/kak-razobrat-katushku-gazonokosilki.HTML https: // labotek.Ru/kak-sobrat-katushku-dlja-gazonokosilki/ https: // tehnika.Expert/Dlya-Sada/Gazonokosilka/Delaem-Samodelnuyu.HTML https: // tehnika4sad.Ru/Trimmery-Motokosy/Katushki-Golovki.HTML https: // geostart.Ru/post/50235 https: // Instanko.Ru/drugoe/trimmer-zamena-leski.HTML

Lawn Mowers assemble, coil, does, lawn, mower, reel