How to assemble an electric trimmer Huter. How to remove the coil and replace the fishing line

How to assemble an electric trimmer Huter

The procedure for winding the trimmer line depends on the type of coil. With one or two antennae, as well as with automatic charging the cord.

Design

  • Pen: with adjustable height
  • Decy material: plastic
  • Building Material: Plastic
  • Ring: Direct
  • Handle shape: T-shaped (bicycle)
  • Anti.Vibration system: there is
  • Wheels: absent

Comment

For a summer cottage I purchased a gasoline trimmer. His engine power is 1000 watts, this is enough for personal use. For mowing, you can use a trimmer line or knife with a mowing width 255 mm. During use, I have established myself on the reliable side, I am satisfied.

Comment

I dash 20 acres of average storm πŸ™‚ Power is really felt when it works πŸ™‚ The starter changed twice (the plastic hooks are very flimsy), I advise you to immediately take a spare. 2 hexagons included the wrong size (it’s good that it was your set). Measured bottle of horror πŸ™‚ After the purchase, I advise you to stretch everything to where the hands will reach (without violating warranty seals). The coil almost immediately went to the furnace, put the sky and earth from Khuskvarna. Foil candles, you need to buy. The main jamb in my copy. With vibration, the adapter from the cylinder to the carburetor is unscrewed (you need to remove the carb.) So if the trimmer is neither like no one wants to be adjusted, try to move the carburetor shows that it walks slightly, remove, twist and all the norms. In general, the thing is good and necessary, if I think, I think and the serious weeds will take, but the assembly quality and equipment are below the average.

Disadvantages of the gasoline braid Hunter GGT 1500S

  • Trimmer noise;
  • A small list of functional capabilities (mainly benzocosa is used for processing lawns, haircuts of grass);
  • Higher price (average price segment).

Advantages and disadvantages of the gasoline braid Hunter GGT 1500S

  • Convenient fast ignition;
  • Vibration suppression system (allows the operator to get tired less during work);
  • Easy to track fuel due to translucent fuel tank;
  • Powerful engine;
  • It is convenient to hold and carry the tool due to small weight;
  • A collapsible bar saves space during the transportation of benzokos;
  • Good build quality and key spare parts for the price are greater than Chinese analogues.

The main purpose of the trimmer Hunter GGT 1500S

  • Hay mowing;
  • Lawns care;
  • Mowing dense thick grass in wild areas;
  • Mowing soft varieties of grass in the country, on the site in front of the house;
  • Giving the form to soft shrubs with thin branches.

Thanks to some technical parameters, using the Hunter GGT 1500S trimmer is very convenient. For example, to change the worn trimmer line, the operator can simply hit the surface of the earth, after which the trimmer line will be replaced automatically with a segment of the desired length.

Basic equipment of the gas troops Hunter GGT 1500S

How to start a gas toss right?

Regardless of the type of action, there is a strict order that must be observed, that is:

Inspection and verification

Any trimmer malfunction can be a serious danger.

Poorly tightened bolts fixing the clutch bell to the engine, can lead to Rapid abrasion of the clutch pads, And any leakage of the fuel system often leads to ignition and burns or fire.

The weak tightening of the gearbox bolts can lead to the fact that the rod shaft bar will jump out of it and the trimmer will stop working. Weak tightening of bolts fixing the handles can lead to involuntary lowering the shaft and damage to the cutting tool.

Therefore, before any launch, you need to at least briefly inspect the device in search of defects. This is especially true for any first launch, it does not matter, after the purchase, or after storage. During work launches It is permissible to inspect only the fuel system For leaks.

Π Π΅ΠΌΠΎΠ½Ρ‚ своими Ρ€ΡƒΠΊΠ°ΠΌΠΈ газонокосилки Huter GGT-1300T

So you will evaluate the quantity and condition of the lubricant not only from the side of the gas station, but also in the area of ​​contact of the shaft bar with the gear of the gearbox.

Same way once every 2-3 weeks check the amount and condition of the oil, Four.Stroke engines filled into a crankcase, if the device will work with a low oil level for a long time, then the probability of jamming of the crankshaft is high.

The gas station is fuel

This operation has to be done after purchasing and winter storage, as well as during the termination of work caused by the production of gasoline. Four-stroke engines are seasoned with pure AI-92 gasoline, and two-stroke with a mixture of fuel and special oil, which we talked about here.

Remember, if you refuel a two.Stroke trimmer after winter storage, Be sure to drain the old fuel from him, After all, it has already lost the lubricant, so the crankshaft bearing and cylinder.Piston group will work without lubrication.

Launching a benzotrimer

Regardless of the type of launch, there are 6 actions that have to always be performed:

  • Fuel pumping;
  • The transfer of the air damper to the “Launch” position (“Closed”, “OFF”);
  • The transfer of the switch to the “inclusive” position (“VCL”, “on”);
  • Pressing and fixing the gas key;
  • The jerk of the starter cable with the choice of free move;
  • Transfer of the air damper to the “work” position (“open”, “on”).

The first 3 points from this list can be performed in any sequence, but you can pull the cable of the air starter only after them. Neglecting fuel pumping will lead to the fact that a hand starter’s cable will have to pull the moving piston of the motor to pump a sufficient amount of air that sucks from the carburetor fuel.

Neglect of the air damper will lead to a strong rethinking of the mixture, What is good for a running engine and extremely bad for starting, because such a mixture is well ignited only inside the heated cylinder.

After the air damper is transferred to the closed position of the incoming air, it is not enough to operate the motor at idle, so click and fix the gas key (accelerator, engine speed regulator). The button for turning on/off the motor blocks the operation of the ignition system, so before starting, transfer it to the “inclusive” position.

After the engine works, transfer the air damper to an open position, because the very re.Enriched mixture is good for launching, because ignites even in the cold cylinder, but due to a lack of air, the fuel does not burn out completely.

An attempt to mow grass with a closed air damper will lead to a sharp drop in the power of the motor and a strong heating of the valves, so the long work (tens of hours) leads to the gap of the valves or damage to the laying of the cylinder head head.

Types of coils

The electric trimmers are installed 3 types of coils, namely:

Automatic and semi.Automatic devices are made in the form of a drum (base), into which a spool or a bobin is inserted, that is, not the entire coil is attached to the electric cost, but only the drum, Mechanical are both integral and collapsible.

Therefore, replacing the coil and replacement of a spray with a trimmer line can be either one or two different operations.

This is due to the design features of such trimmers, because a full.Fledged replacement of the head at home is not provided, and the price of a good coil is often not much less than the cost of the electrimmer.

In addition, the coils for electric core with a straight and curved bar are not interchangeable, because They have different threads.

Huter trimmers (Huter)

Huter electric and gasoline braids successfully combine high efficiency on the site and minimum fuel consumption. When developing each trimmer, the manufacturer uses branded innovative technologies aimed at increasing endurance and comfort during operation of technology. This makes Huther garden tools one of the most high.Tech in the market, and makes it possible to successfully use them in almost any working conditions.

Huter foundation and development

The German enterprise Huter is one of the most famous world brands involved in the production of high.Quality household and garden equipment. The history of the brand begins in 1979. It was then that the first plant of the enterprise began to function in the German city of Nordhausen.

Since the launch of its production, the company has headed for the active development and gradual implementation of its own technologies. As a result, by the 90s of the XX century, the brand managed to enter the number of the most popular world manufacturers of electrical equipment, as well as high-quality equipment for household and economic operation.

Today, Huter is largely known for its electric and gasoline trimmers. Garden instruments of this brand are characterized by high performance, low fuel consumption and electricity, as well as ergonomics and pleasant modern design. Simplicity in operation and maintenance makes it possible to begin the use of trimmers of Huther not only quite experienced, but also beginner gardeners.

Huter Get-1500B electrimmer. REVIEW.

This year it was decided to buy to help a gasoline trimmer, an electric trimmer Huter Get-1500b. Gasinin is certainly mobile and convenient in large areas of mowing, but with regards to simplicity of service, of course, it cannot compete with electric.

The basic requirements for choosing an electric trimmer were:- the upper location of the engine;- power of at least 1000W;- the ability to work with trimmer line and disk (knife);- Type of drive of a straight shaft, not a cable.

The type of engine is electric, synchronous, brushThe location of the engine is upperNetwork voltage 220-230v 50 HzNominal power 1500 WRevolutions 8000 rpmType of cutting element trimmer line knifeFishing diameter 2.4 mmThe type of rod is straight, collapsibleType of the handle “Bicycle”A bevel width with a knife 255 mmBevel width with trimmer line 420 mm

Huter Get-1500B equipment:Upper rod. 1 pc.Lower bar. 1 pc.Cutting disk. 1 pc.Coil with trimmer line.1 pcs.Protective casing. 1 pc.Shoulder belt. 1 pc.Fastener.1 pcs.Handway. 2 pcs.Tool set. 1 pc.Operating manual.1 copies.

Assembly and setting up the electrimmer Huter Get-1500b.

Here we do everything according to the instructions, since everything is clear, accessible and in the pictures.

I want to note: on the one hand, the possibility of disassembling the bar is a plus, but on the other a huge minus due to the fact that this reduces the margin of strength and can give additional vibration during operation.

And again, a remark on the reserve of the strength of the plastic base of the casing on which the tearing knife of the trimmer line is fixed. The plastic here is very thin and at good speeds of a larger.Diameter trimmer line, it can simply demolish this brick with a plastic base.

Huter Get-1500b. The device is very powerful 2 liters.With. And it may well measure with gasoline trimmers, so we do not neglect the means of protection and safety precautions.

At a power of 1.5 kW trimmer mows any grass, I think this is understandable and so. What is really not enough in comparison with gasoline is the possibility of adjusting the revolutions or a smooth start in an electrical design for a thinner mowing in hard.To.Reach places. By the way, the GET-1700B model has a smooth start function.

In terms of noise, of course, it is lower than that of the gasoline trimmer, but taking into account this power, the noise is still not small (I advise protective headphones).

Eventually Huter Get-1500B completely suits me by power, but for greater reliability and ease of use, in my opinion, a number of improvements are required.Namely: strengthening the connecting coupling of the bar, replacing and transferring the inclusion button to a more convenient place of the handle, as well as the reinforcement of the founding of the mounting of the cure knife of the trimmer line.

Why you need to put a knife on a trimmer

The trimmer with a knife installed on it is most conveniently used for a more comfortable mowing of high and loaded grass in the country. The trimmer line on the motorcycle is in such cases does not cope. Thin torn very quickly. Using Tolstoy 2.3 mm cord or homemade rods with cables forces the vegetation to wind up on the rogue. This increases the load on the engine. As a result, the piston group and other mobile units of the unit wear out very quickly.

If the mowing of a weeds is produced by an electric trimmer without a knife, only with a trimmer line, even a thick with a figure section, the problem cannot be solved. There is always a risk of overheating the electric motor and disable flexible shaft. And it’s all in a large torque of the electric motor. The grass wound on a spindle creates strong resistance to the shaft resembling a speedometer cable that does not withstand and twist.

In order to protect the equipment from premature wear, manufacturers have provided the ability to install special knives on trimmers. The design and shape of existing cutting elements allows you to easily cope not only with coarse and outgrown with grass, but also to successfully fight the young shrub.

Common malfunctions of electric trimmers

Electric trimmers differ from gasoline devices with a more simplified design. Conditionally electric braid is divided into mechanical and electric part. Accordingly, the same groups of malfunctions are distinguished, arising to these equipment.

Most of the breakdowns can not be visually identified. For this you will need to use various devices. You can visually determine the following:

  • The integrity of the power cable is violated (insulation is broken from it, or it is clearly interrupted);
  • Sustaining or jamming of the trigger button;
  • Mechanical external damage to motorcycles;
  • Problems with the cutting part;
  • Stop stop when clogging with grass;
  • Damage to the fork.

To find out which part has broken in other cases, you will need to disassemble the electric shock and sequentially check the most likely options

At the same time, they pay attention to the external manifestations of deviations from the normal operation of the device. They contribute to the establishment of the cause. Repair of an electric trimmer will require the following devices and tools:

Repair of an electric trimmer will require the following devices and tools:

Can you make a trimmer coil with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the trimmer line from ordinary plywood 10-12 mm thick.

  • Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
  • Cut the disk with a jigsaw or hacksaw for metal.
  • Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
  • You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
  • To fix the trimmer line, you can screw several screws into the plywood.

Such a homemade mowing nozzle is fixed on the shaft with a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the trimmer line of the required length and press it again.

Also, a mowing nozzle for fixing the trimmer line on it can be made from a metal sheet. How to do this can be understood from the next video.

How to assemble a trimmer Huter

The Huter GGT-2900S trimmer belongs to the class of gasoline trimmers optimally designed to work on lawns and gardens. The GGT-2900S has a two-stroke engine that significantly expands the capabilities of the device, for example, without linking the braids to power sources, as is typical for electric trimmers. In this sense, the described model can also be used to process large areas, since the main factors in this case will be: the presence of a sufficient amount of fuel and the optimal technical condition of the device.

The power of the Huter GGT-2900S is 2.9 kW, which, along with the features of the cutting tool (trimmer line / knife), belongs to the semi-professional class of such devices. Therefore, the model can be used not only in the country and at summer farms, but also on small farms. The GGT-2900S copes with both grass mowing and cleaning areas with a small shrub. The weight of the trimmer is 7.5 kg, which, given the presence of a removable type of rod, makes the release of transport relatively simple, including in a regular car.

Advantages of Huter GGT-2900S

  • The presence of a gasoline two.Stroke engine makes the device more autonomous compared to electrical types of mowers.
  • The engine has sufficient power and high reliability to solve problems. It is also equipped with an anti.Vibration system and is easily launched.
  • The design of the trimmer provides for the presence of a translucent fuel tank, which is convenient to season with fuel and control its level.
  • A convenient and reliable trimmer control system is provided, located on an ergonomic handle.
  • Arrow 2900S has a removable mechanism for light and convenient transportation.
  • The trimmer is easily disassembled and assembled, but in the collected state is distinguished by the reliability of all nodes and devices.
  • The buyer receives a convenient belt, glasses to protect the eyes during operation and disc 40 TP in the set of the model.

Work comfortably and safely

Of course, the operator must comply with all the recommendations and safety requirements, comply with the rules of operation of the trimmer. However, in addition, the manufacturer took a number of measures to develop a device in order to increase the level of security when working with a scythe. They include, but not limited:

  • Protective cover to prevent stones and garbage to the user,
  • Throttle, so that the operator could not accidentally press the trigger and start to rotate
  • Cutting tool when starting the engine,
  • Anti.Vibrational system to prevent the harmful effects of vibrating three.Dimensional elements on hand and other parts of the operator’s body.

Operational features Huter GGT-2900S

The operation of the trimmer is not very complicated, and after a thorough study of the instructions and assembly of the resulting product, you can begin to prepare a trimmer for work. We will briefly consider how to assemble Huter GGT-2900S and prepare it for work. Since the GGT-2900S is equipped with a detachable rod, it is first necessary to combine two elements of this part using a coupling, which must be fixed. Before moving on to the next step, you need to make sure that all components are securely connected. After that, you can start fastening the control levers using a special key that is included in the delivery kit. When connecting the elements, always check that everything is done reliably. Now you can go to the next step: connect the rod with the engine. Installation is carried out using a standard set of bolts. After the rod is connected to the engine, you can install the housing and cutting elements. Read more about the step.By.Step assembly of the trimmer in the user guide.

The assembled trimmer can now be prepared for further work on the site. Preparation for operation begins with the preparation of the fuel mixture. At this stage, follow all the recommendations of the manufacturer for brands and the quality of the components of the fuel mixture, as well as strictly follow the method of preparing the fuel mixture, which, in fact, is not very difficult.

Since the Huter GGT-2900S is equipped with an air-cooled two-stroke engine, high-quality oil specially designed for this type of engine is required to prepare the fuel mixture. According to the classification, this is API TV / API TS, JASO FB / JASO FC. It is recommended to fill in Huter production under the Huter 2T trademark. The second component of the mixture should be high.Quality gasoline, the octane number of which is at least 92. It is strictly forbidden to use oils in the fuel mixture produced for water cooling engines. The fuel mixture is prepared in a ratio of 1:40 (1. Oil, 40. Gasoline) or in accordance with the recommendations of the oil manufacturer.

Use a special measuring container to prepare the mixture. The amount of the mixture should only be calculated in one cycle so that after the end of work in the tank there are no residues of the fuel mixture (it should not be left in the tank until the next cycle of work). In addition, never use the tank itself to prepare the mixture, and also do not work with the components of the fuel mixture near fire or smoke during fuel preparation.

After the correctly refueling fuel mixture is flooded into the tank, you can begin to directly prepare the trimmer to work. To do this, the user must first put on a belt similar to a backpack, and reliably, but conveniently, fasten it. After that, using a special carbine, the trimmer is fixed on the belt and, if necessary, is regulated. Read more about the preparation of the trimmer for the use of cm. In the user manual.

The trimmer, gasoline or electric, is the only correct solution for mowing grass in hard.To.Reach places where you cannot work with a wheeled lawn mower. Metal knives or a special trimmer line are used as a cutting tool in trimmers, which is clogged into a trimmer coil. But, unfortunately, three.Dimensional heads eventually become unsuitable. Some malfunctions can be eliminated with your own hands, and some require a complete replacement of the mowing.

Trammer coil device

The heads of mowing for trimmers are available in many performances. Both simple and complex. The figure below shows Semi.Automatic trimmer head Husqvarna (Husqvarna) was disassembled from a mower.

Huter trimmers (Huter)

Huter electric and gasoline braids successfully combine high efficiency on the site and minimum fuel consumption. When developing each trimmer, the manufacturer uses branded innovative technologies aimed at increasing endurance and comfort during operation of technology. This makes Huther garden tools one of the most high.Tech in the market, and makes it possible to successfully use them in almost any working conditions.

The German enterprise Huter is one of the most famous world brands involved in the production of high.Quality household and garden equipment. The history of the brand begins in 1979. It was then that the first plant of the enterprise began to function in the German city of Nordhausen.

Since the launch of its production, the company has headed for the active development and gradual implementation of its own technologies. As a result, by the 90s of the XX century, the brand managed to enter the number of the most popular world manufacturers of electrical equipment, as well as high-quality equipment for household and economic operation.

Today, Huter is largely known for its electric and gasoline trimmers. Garden instruments of this brand are characterized by high performance, low fuel consumption and electricity, as well as ergonomics and pleasant modern design. Simplicity in operation and maintenance makes it possible to begin the use of trimmers of Huther not only quite experienced, but also beginner gardeners.

assemble, electric, trimmer, huter, remove

How to look for malfunctions in the mechanical part

The transmission of rotation from an electric trimmer of a mowing head is performed in the same way as models with an internal combustion engine: a whole shaft works inside the rectangular section of the bar, and the cable has a curved cable.

Their length, diameter and design are selected by the manufacturer for specific dimensions of the composite bar.

Features of the junction of the composite bar

It is made by an adapter with a screw clamp.

String Trimmer Ignition Coil Replacement #545046701

The large screw head is made to conveniently adjust the position of the mowing organ at the bottom of the bar. The rotation angle is selected individually.

It is convenient for me to expose it so that the longitudinal axis of the protective casing and the axis of the electric motor are located in the same plane.

In this place, a malfunction associated with the transfer of torque from a direct shaft to a cable may sometimes occur in this place. It is manifested by the fact that the trimmer works normally at the idle speed, and already under a small load, the mowing head stops rotating.

The method of its elimination was well shown by the owner of the video “Repair of the Electrimmer” Roman Shapkov. I recommend to see.

Method of attaching a mowing head and a casing

On my trimmer from below the rod, the adapter is fixed with rivets, into which the fastener bolt of the protective casing will be plunged.

The output shaft of a rotating cable has a hexagon at the end. A plastic mowing head is put on it.

From the inside, a return spring of the automatic discharge of trimmer line during kosbe is inserted into it.

A spool was inserted into it. It is fastened with a fixing nut from above.

The device of a spitter head with a trimmer line is quite simple.

However, all plastic parts do not have high strength, subject to wear. Their working surfaces are erased. After three seasons of work on my trimmer, the output holes of the trimmer line from the mowing head expanded, the thickness of the fixing nut decreased.

It is difficult to apply protective measures to wear, and repair of these parts is easiest to fully replace the head. It is easy to buy it: you just need to know the exact dimensions of the hexagon and evaluate the new design according to the working characteristics.

The secrets of the selection of trimmer line

Among the frequent malfunctions of the trimmer coil, there are cases when the trimmer line ended or simply confused due to improper winding on the spool. It is not difficult to eliminate them.

But in practice, I met with another defect in the trimmer line, which was sold on the state retail chain from the Moscow company Patriot LLC. Her view in the factory packaging.

As I understand it, it is specially hidden in a sealed package: you can not touch when buying.

When I opened the packaging to install the trimmer line in the spool, its plasticity immediately caught my eye, and not elasticity. It is easily bending, behaves like a soft wire: when in contact with the grass, it immediately breaks. It is impossible to mow: she managed to return to the seller.

Since then I have been buying only that trimmer line that can be rolled in my hands and evaluate its operational properties.

I try to refuse varieties of ordinary round trimmer line. I prefer a ribbed shape to them with faces: asterisk, trapezoid, square or triangle. They are better cut off the grass.

How to eliminate increased vibration

Reliably collected trimmer mechanics is well balanced. It provides convenient work. However, bearings can be worn out over time, lose lubrication.

A prefabricated shaft transmitting rotation from the engine of a spool is able to touch the internal walls of the bar, creating excessive friction with heating.

Such a defect can and must be eliminated. This technology is shown by the TV repairman with his video “Vibration during the operation of Elektokosa”.

Model operating instructions

The above trimmer gasoline “Huter” should be used taking into account the safety rules that are registered in the instructions. Of these, you can find out what to use equipment to persons who are under the influence of alcohol or physically tired are unacceptable. Before starting work, it is necessary to arm yourself with special means of protection, among them the appropriate clothes, protective glasses, mittens or gloves, helmets and headphones should be highlighted among them. Equipment should not be used near flammable and explosives. This also applies to the conditions under which high humidity remains.

EASIEST WAY TO STRING YOUR WEED EATER

  • Before inserting the trimmer line into the coil, turn off the booster engine or turn off the electric trimmer to avoid injuries that may occur if the cutting tool accidentally begins to rotate.
  • Unscrew the attached nozzle of the transfer shaft. To do this, fix the shaft, combining the openings on the puck and on the axis and inserting a metal rod or screwdriver.
  • Unscrew the nozzle. You should know that the thread on the shaft remains. Therefore, turn the coil of the trimmer to the right, that is, clockwise.
  • Disassemble the mowing head. Most often the main cover is attached on the clips. To remove it, you will need to lower these clamps onto the case, squeezing the edges of the lid. If your trimmer has a semi.Automatic mower with a button below, carefully disassemble the nozzle, as you can lose a spring that sometimes pops up when removing the cover.
  • Cut the required amount of fishing. Usually its length is 5 meters. Use the cord with the diameter indicated in the instrument guide. It is not recommended to exceed the maximum diameter of the mowing trimmer line, as this will increase the load on the engine and increase the gas mileage.
  • Find the middle of a piece of cord, folding it in half. You will get a loop.
  • Cut the coils of special grooves (there may be holes). Insert the loop of the trimmer line into this groove.
  • Wind a trimmer line on a reel, turning it counterclockwise. It is necessary to fill the cord as evenly as possible, the turns should be carried out without ceiling and with good tension. After the winding is completed, leave the free ends of the trimmer line about 20 cm long and fix them in grooves on the sides of the coil.
  • Collect the mowing head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if available). Insert the coil into the housing and push the ends of the cord through the holes or eye.
  • Put on the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Turn the trimmer coil to the left (counterclockwise).

Read how to disassemble a trimmer mowing head

How to assemble a trimmer Huter

The Huter GGT-2900S trimmer belongs to the class of gasoline trimmers optimally designed to work on lawns and gardens. The GGT-2900S has a two-stroke engine that significantly expands the capabilities of the device, for example, without linking the braids to power sources, as is typical for electric trimmers. In this sense, the described model can also be used to process large areas, since the main factors in this case will be: the presence of a sufficient amount of fuel and the optimal technical condition of the device.

The power of the Huter GGT-2900S is 2.9 kW, which, along with the features of the cutting tool (trimmer line / knife), belongs to the semi-professional class of such devices. Therefore, the model can be used not only in the country and at summer farms, but also on small farms. The GGT-2900S copes with both grass mowing and cleaning areas with a small shrub. The weight of the trimmer is 7.5 kg, which, given the presence of a removable type of rod, makes the release of transport relatively simple, including in a regular car.

Advantages of Huter GGT-2900S

  • The presence of a gasoline two.Stroke engine makes the device more autonomous compared to electrical types of mowers.
  • The engine has sufficient power and high reliability to solve problems. It is also equipped with an anti.Vibration system and is easily launched.
  • The design of the trimmer provides for the presence of a translucent fuel tank, which is convenient to season with fuel and control its level.
  • A convenient and reliable trimmer control system is provided, located on an ergonomic handle.
  • Arrow 2900S has a removable mechanism for light and convenient transportation.
  • The trimmer is easily disassembled and assembled, but in the collected state is distinguished by the reliability of all nodes and devices.
  • The buyer receives a convenient belt, glasses to protect the eyes during operation and disc 40 TP in the set of the model.

Work comfortably and safely

Of course, the operator must comply with all the recommendations and safety requirements, comply with the rules of operation of the trimmer. However, in addition, the manufacturer took a number of measures to develop a device in order to increase the level of security when working with a scythe. They include, but not limited:

  • Protective cover to prevent stones and garbage to the user,
  • Throttle, so that the operator could not accidentally press the trigger and start to rotate
  • Cutting tool when starting the engine,
  • Anti.Vibrational system to prevent the harmful effects of vibrating three.Dimensional elements on hand and other parts of the operator’s body.

Operational features Huter GGT-2900S

The operation of the trimmer is not very complicated, and after a thorough study of the instructions and assembly of the resulting product, you can begin to prepare a trimmer for work. We will briefly consider how to assemble Huter GGT-2900S and prepare it for work. Since the GGT-2900S is equipped with a detachable rod, it is first necessary to combine two elements of this part using a coupling, which must be fixed. Before moving on to the next step, you need to make sure that all components are securely connected. After that, you can start fastening the control levers using a special key that is included in the delivery kit. When connecting the elements, always check that everything is done reliably. Now you can go to the next step: connect the rod with the engine. Installation is carried out using a standard set of bolts. After the rod is connected to the engine, you can install the housing and cutting elements. Read more about the step.By.Step assembly of the trimmer in the user guide.

The assembled trimmer can now be prepared for further work on the site. Preparation for operation begins with the preparation of the fuel mixture. At this stage, follow all the recommendations of the manufacturer for brands and the quality of the components of the fuel mixture, as well as strictly follow the method of preparing the fuel mixture, which, in fact, is not very difficult.

Since the Huter GGT-2900S is equipped with an air-cooled two-stroke engine, high-quality oil specially designed for this type of engine is required to prepare the fuel mixture. According to the classification, this is API TV / API TS, JASO FB / JASO FC. It is recommended to fill in Huter production under the Huter 2T trademark. The second component of the mixture should be high.Quality gasoline, the octane number of which is at least 92. It is strictly forbidden to use oils in the fuel mixture produced for water cooling engines. The fuel mixture is prepared in a ratio of 1:40 (1. Oil, 40. Gasoline) or in accordance with the recommendations of the oil manufacturer.

Use a special measuring container to prepare the mixture. The amount of the mixture should only be calculated in one cycle so that after the end of work in the tank there are no residues of the fuel mixture (it should not be left in the tank until the next cycle of work). In addition, never use the tank itself to prepare the mixture, and also do not work with the components of the fuel mixture near fire or smoke during fuel preparation.

After the correctly refueling fuel mixture is flooded into the tank, you can begin to directly prepare the trimmer to work. To do this, the user must first put on a belt similar to a backpack, and reliably, but conveniently, fasten it. After that, using a special carbine, the trimmer is fixed on the belt and, if necessary, is regulated. Read more about the preparation of the trimmer for the use of cm. In the user manual.

The trimmer, gasoline or electric, is the only correct solution for mowing grass in hard.To.Reach places where you cannot work with a wheeled lawn mower. Metal knives or a special trimmer line are used as a cutting tool in trimmers, which is clogged into a trimmer coil. But, unfortunately, three.Dimensional heads eventually become unsuitable. Some malfunctions can be eliminated with your own hands, and some require a complete replacement of the mowing.

Trammer coil device

The heads of mowing for trimmers are available in many performances. Both simple and complex. The figure below shows Semi.Automatic trimmer head Husqvarna (Husqvarna) was disassembled from a mower.

Work and maintenance

There is nothing complicated in working with Huter Get-1000s. Turned on. And go, even the child will cope. In order to safety (and additional reduction in production, as I believe), the manufacturer refused the inclusion fixer. Therefore, for launching here you need to simultaneously press two buttons, and to continue work. Continue to keep them pressed. Not too comfortable, but safe for both the trimmer and the user.

assemble, electric, trimmer, huter, remove

The device, as I already wrote above, weighs a little more than five kilos. You can work with it for a long time without tired. Over, the vibrations of the electric motor are much weaker, and the noise is quieter than the gasoline analogues. Although the back and hands, of course, still get tired. If you are not a bodybuilder, then you are unlikely to figure out one session with a large site, you will have to take breaks.

At the same time, performance is a clear advantage of GET-1000s, especially by the standards of electrical equipment. The power of the device is comparable to gasoline motorcycles, and this is something yes. Neither high grass, nor coarse weeds, nor young bushes will be a problem for him. The main thing is to grasp the strength of the trimmer line.

The protective casing of the trimmer is quite narrow, it closes the third of the circle. On the one hand, mowing is so convenient: nothing interferes and does not cling to the grass. On the other hand, almost no protection for the kosar himself does not give. Therefore, while working in green porridge, you will have not only legs, but also a stomach. Herbs scraps scattered in all directions already on the chest, or even higher. There are no glasses or other eyes for the eyes, but this question must be taken care of yourself. Pulling up a charge of caustic herbal juice in the eye is still a pleasure.

With the exception of this moment, there is definitely nothing to complain about here. Electricca works quietly, does not smoke, almost does not require maintenance and is able to solve any problems on a small garden plot.

Huter Get-1000s costs in the region of 3000-4000 rubles. For a light, comfortable, quiet, simple, work and maintenance of an electric trimmer, this price looks more than adequate. Of course, I would not count on the fact that you can inherit this device by grandchildren. However, to care for the lawn, it is great, it copes with its work at one hundred and the price tag fulfills. What else is needed?