How to change a fishing line for a trimmer for a Brait benzotrimmer. Step 1: Rear off the head of the head of the grass for the grass

How to wind a fishing line for a trimmer for a trimmer for grass

To wind a fishing line for a trimmer for a gasoline or electric trimmer for grass, you do not need to have some special skills. First, it is important to decide on suitable consumables, and then choose the best way. You can refuel a fishing line for a trimmer to the device coil using two different ways.

change, fishing, line, trimmer, brait

The main elements of the trigger is a mowing spike, which is a cylindrical case with a coil inserted inside (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in the method of supply and refueling of the cord. There are three types of heads in total:

  • Automatic. The fishing line is submitted after that, as the user reduces engine speed. Automatic supply of the cord is very convenient when you need to do a large amount of work. The minus of such a head is a large thread consumption.
  • Semi.automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for grass works at full speed. It is only necessary to slightly hit the apparatus with the head on the ground (this will remove the locking of the fishing line), and the cord due to centrifugal force will move out of the bobbin. Then the fishing line for the trimmer is cut to the required length with a knife, which is located on a protective casing.
  • Manual. To lengthen the cord, it is necessary to stop the device. After that, the fishing line for the trimmer will need to be pulled manually.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut. A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

  • See the information about the thickness of the fishing line in the instructions attached to the trimmer.
  • Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters.
  • Another option is to try to insert the cord into the output. If it easily passes into it, then the selected fishing diameter is suitable for use.

You can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

  • The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
  • Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
  • The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
  • You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
  • The most durable is a two.component cord with an internal core and a round section.

Keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

How to change a fishing line for a trimmer on a gasoline trimmer

Coil with one working osik

The most ordinary option and a light sequence of actions:

  • The dimensions of the bobbin and the length of the unique factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the squeezer.located squeling fixing technological hole.
  • The fishing line for the trimmer is wound on the drum in reviting the spilles on the trimmer product direction. usually, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • The small section of the fishing line is left free to withdraw it out. it is fixed in the special side on the inside of the bobbin created to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.di.carcass coils Lines for a trimmer It extends into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. the arrow with the arrow exaggeratedly indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference in the winding of the fishing line in the two-drummer coils is that the line of the fishing line 2-5 m long is in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The above will clearly show how to tuck a fishing line for a trimmer to the coil of a trimmer for the grass and correctly wrap it. this operation is nothing complicated and, with some patience, will certainly be crowned with a furorur:

Alternative way of charging fishing line in a reel

Drums of modern gas.coculuscs, 2 antennae, have a special eye in each of the channels. Thanks to the ears, it becomes possible to wrap the fishing line for the trimmer for each channel separately. For someone, a similar way of winding the fishing line is preferable.

Remove the rogue. To do this, it is better to lock it with a screwdriver or something like that. The coil is unscrewed clockwise.

Remove the lid and remove the drum. Usually the cover is fixed with a pair of latches. When the drum is disconnected, access to the spring will be revealed. Do not lose it!

Cooking two separate fishing lines of similar length.

  • We wrap a fishing line for a trimmer to one of the channels. Typically, a fishing line for a trimmer is wound against spool rotation.
  • We fix the tip of the fishing line so that it does not unwind. Especially for this purpose, appropriate connectors are provided along the perimeter of the very edge of the drum.
  • Repeat all of the above operations with the 2nd fishing line. It must be wrapped in one direction with the first cord.
  • Collect a coil and put it on a motorcycle.

Typically, such drums have the usual hook on the central partition of the channels, and a separate eye in each channel. The user of a lawn mower with such a drum has the opportunity to choose the method of charging fishing. Any of the ways good in its own way.

Below is a video, the creator of which clearly indicates the above method of refueling the fishing line. The display of an alternative method begins with the 8th minute exactly, the 1st part is devoted to the classical method of charging the cord.

What types of forests I am

The most common type of fishing line, which is suitable for almost all types of coils. a round cross.sectional cord. This is a regular fishing line for a trimmer suitable for mowing of juicy grass, but it will be much more difficult to mowed with dry, and even more so it cannot cope with the shrub.

As a rule, the diameter that can mow young grass does not exceed 1.6 mm. The thicker the thread, the more rough grass it is able to overcome.

Important! Choosing a fishing line for a trimmer for a trimmer for grass must be guided by the instructions for your tool, since the thin thread will lead to an increase in wear of the torque, and thick to overload of the engine.

There are fishing lines with sharp faces in the form of a sprocket or square, this option is more adapted to mowing dry grass just due to the existing sharp faces, but its lack of wear is more wear and it is inferior in strength to the round cord.

There are fishing lines with improved aerodynamics with characteristic dentes, scales and notches, a similar product makes less noise, but they use it only on benzos, since the output of such a thread from the coil is difficult, it is most often used with disks in which segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine of more than 1.5 liters.With. Apply cords with a metal cable inside.

This thread is ideal for mowing dry grass and small shrubs. The presence of a core, positively affects the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly larger than the above opponents.

Viking is a brand that knows a lot about

The world.famous Viking garden manufacturer was founded in Austria. Today this brand is one of the fastest.growing and profitable units of the German giant Stihl.

The main vector of development of Viking is the production of high.quality gasoline and electric garden equipment. The brand’s lineup includes lawn mowers, grinders, aerators, motor.cultivators. Particularly popular in the European and American market are trimmers for Viking. During their development, the manufacturer always listens to the opinions and wishes of gardeners. Thanks to this, the garden technique of Viking is highlighted by maximum reliability, ease of operation and unpretentiousness in maintenance.

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Types of trimmer heads

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a fishing line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

  • Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the fishing line is convenient if large volumes of work are performed, such rods have one drawback. a large thread consumption.
  • Semi.automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head for the grass on the ground (this removes the cord lock), and the fishing line for the trimmer, due to the centrifugal force, moves out of the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
  • Manual. For lengthening the cord, the device is required, after which the fishing line for the trimmer is handed out manually.

Based on the above, semi.automatic bobbins are the most optimal option. It should also be borne in mind that the coils for a trimmer for grass are one.built (used only to trim the grass) and two.string, which are used to mow high grass and small, with thin stems of shrubs.

How to quickly and correctly season a fishing line for a trimmer to a trimmer for grass?

When you figure out how to change the cutting material, further use and maintenance of the electrimmer will be greatly simplified. To wind a fishing line for a trimmer for a trimmer for grass, several operations should be performed, namely:

Unscrew the nozzle, rotating the drum to the right. You will have a head in your hands with the remnants of an old thread. Open it with a screwdriver or squeeze the lock and turn the lid towards the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw away all the internal details of the drum. To change the fishing line for a trimmer in a trimmer, you need to get a coil and remove the remains of the material. Take 5 meters of a new thread and fold it in half. In the middle of the coil there is a hole into which you need to insert the material. There is also an arrow indicating the direction to wind a fishing line for a trimmer for a trimmer for grass

It is important to take into account some points. If there are two holes in the coil, then half of the fishing line for a trimmer for the grass should be seasoned in one direction, and the second in the opposite

Ending to insert the material, it is better to leave 15-20 cm free. Assemble a drum, install a spring and washer in place. After that, holding the coil, tie the ends of the fishing line in the holes on the sides of the nozzle. Then put the head in place, pulling the cutting material.

Specifications

Consider how the clutch adjustment occurs at MTZ-320, how to properly put a clutch disc. As well as on tractors of the type MTZ-80, 82 and 82-1, on the MTZ-320 there is a dry single-disk Friction clutch, which belongs to a constant type.

The coupling is fixed on the flywheel 6 bolts placed on three pins. Twisting the moment from the press of pressing and the flywheel of the motor passes to the driven disk, and then to the shaft. There are 9 pairs of springs between the squeezing discs.

The pedal can walk freely in the basket, but the boundary limit is 40 mm. If this parameter is larger, it will be difficult to switch the gearbox, there will be problems with the operation of the mechanism.

With an insufficient course of the pedal, a slip of the discs may well occur, which threatens the wear of the disks.

How to change your petrol combi-trimmer from using a trimmer line to a grass blade

change, fishing, line, trimmer, brait

You can cope with this situation through the installation of the clutch MTZ-320. This is carried out according to the following scheme:

  • It is necessary to unscrew the thrust from the lever and pull out the finger.
  • Scroll the lever against the sentry to the stop of the bearing into the lever. Then you need to twist the plug fork, connect the holes on the lever and fork.
  • The fork must be started at several revolutions and try to connect with the lever, for which you need to use the finger.
  • At the very end, the contract is tightened, the finger is fixed.
  • After that, it is necessary to check the serviceability of all nodes and mounts that are included in this system of the MTZ mini-tractor.

When adjusting the clutch MTZ-1221, adjust all the devices that together constitute the adhesion of MTZ. Unlike models of mechanisms installed on the MTZ-80, 82 and 320, the adjustment of the clutch at 1221 provides for work with a system of a different type.

On this model of the tractor stands a double.disc friction mechanism where there is a pressure disk called a basket. The driven part of the system also includes 2 leders, on which there are rotation extensions of rotation. They are on the power shaft, which provides an effective connection.

Before you put a new coupling on mini-tractors, you must first remove it. Firstly, bolts are installed that are wrapped in a pressure disk. Secondly, the mounting nuts are unscrewed and the discs are removed. Thirdly, first the led, then the average led, at the very end-the second led.

The adjustment provides for the installation of the slope of the shield in the bearing of the flywheel. Then the first driven is put, and then the one that is mounted in the grooves of the flywheel.

The second driven is followed, after which it is necessary to put in place the wheels that are assembled. They must be fixed with nuts and bolts. At the very end, the position of the squeeze levers is regulated.

In order for the squeezed levers to fall into place, it is necessary to injected and turn the regulatory nuts alternately, put them with the other side. When repaired levers can be controlled, it is necessary to install stop plates and remove the frame.

Fishing winding

It is easy to insert a fishing line for a trimmer in a trimmer for grass. To conduct this operation, it is necessary to adhere to a simple algorithm of action. The first step will be the determination of a sufficient amount of consumable. To make its calculations, it is necessary to wind a fishing line for a trimmer on a spool so that the resulting coil of the past is less or equal to the diameter of the sides of the structure.

When you have decided on the size of the cord, it is necessary to fold it in such a way that one part of it is 15 cm longer than the other. The winding of the cord’s thread begins with the side dividing the spool into 2 parts. There will be a mount in which you need to insert a thread in half.

Now you need to understand in which direction to refuel a fishing line for a trimmer to a trimmer for grass. To do this, you need to inspect the spool. often a special arrow is indicated on it. If there is no explanatory information, you should find a pointer on a trimmer head, and proceed to wind in the opposite direction. Further actions can be divided into 4 stages:

  • Completion of the winding of the cord. To do this, it is inserted into the side groove on the coil. Its second end is attached to the opposite groove.
  • The ends of the fixed fishing line are cut. Allowance remains 7-10 cm.
  • The seasoned part is placed in the head of a trimmer for grass. To do this, an alternate insert and pulling the thread into the input holes of the structure is performed.
  • The thread is pulled out of the grooves. Upon completion of the action, the product cover is fixed using fixers.

After completing the last stage, the garden tool is ready to work. If, after inserting the fishing line into the trimmer for the grass, the device works incorrectly, it is recommended to repeat the procedure by changing the thickness or type of cordial thread. Otherwise, the product may fail.

How to refuel a fishing line for a trimmer trimmer for grass?

Any apparatus for mowing vegetation is necessarily equipped with a coil, which, in turn, can differ in different models of a thread supply system (automatic, semi.automatic and manual). It is from this parameter that it is worth pushing before deciding how to refuel a fishing line for a trimmer to a trimmer for grass.

In order to refuel a fishing line for a trimmer in a trimmer for grass, you must take at least 5 meters of material, which then folds in half. The center of the cutting element must be inserted into a place specially designed for this, and after that with the help of visual tips on the coil displaying the direction, you should wrap the device for cutting. At the end of all the work, the lid, of course, will have to be tightened.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Features of the use of trimmers

A trimmer for grass, mowing grass with a fishing line, can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, a row in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer for grass, exists in several variations:

As the names understands, the types of trimmer for grass are noticeably different from one another. But regardless of the type of this tool, its cutting element can be a fishing line for a trimmer. Of course, a trimmer tilted for the grass for a trimmer is not infinite. And sooner or later it will need to be replaced by a new.

Fishing consumption directly depends on the frequency of using the device and the scale of the work performed. The more herbs are brazen and the more often it is trimmed with a trimmer for grass, the more actively a fishing line for a trimmer is consumed in it. And, accordingly, the faster it will end. In this regard, the question arises: how to refuel a fishing line for a trimmer to a trimmer coil for grass?

Not everyone knows the answer to this question. But the winding of the fishing line on the coil plays an important role in the work of a trimmer for the grass. To make the device normally, it is very important to correctly wind a new fishing line for a trimmer to the reel. About how to change a fishing line for a trimmer on a trimmer, and will be discussed in this article.

Which line for a trimmer to choose

Before you stock up on this material for refueling in a trimmer for grass, you need to decide on the choice. After all, the usual so.called round fishing line for a trimmer is far from the only existing look. How to choose the most suitable? First you need to determine the working conditions.

Type choice. a line for a trimmer with a round section is the most common. It will suit any reels with the rarest exceptions. This type of consumable is suitable in order to mow fresh, juicy grass. But with the mowing of the so.called dryness, this kind may not cope anymore. It is pointless to mention attempts to mow shrubs and mention.

In addition to the usual type, there are others with sharp faces. Usually they are made by a “star” or “square”. The presence of sharp faces is the main feature and key difference between these threads.

It is thanks to this feature, the threads of such species are able to mow dry weeds. But the spicy threads are not devoid of disadvantages, the main of which can be called rapid wear and strength, markedly inferior to the round type.

In addition to the already mentioned types of forests, there are still interesting and often encountered varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. Threads of this type are often used in tools working on gasoline and having an engine more powerful than one and a half horsepower.

Threads with a metal core are both with a round section and with sharp faces. Regardless of the type of cross section, such threads are the best suited to overcome hard.to.stop plants. Threads related to this type easily mow not only dry grass, but even small shrubs.

The threads with wire inside are favorably different from other types of consumables for their incredible wear resistance. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Choice in thickness

In addition, special attention should be paid to the thickness of the consumption material. For mowing young grass, a thread is suitable with a diameter of one and a half millimeters. The larger the diameter of the thread, the more dry and rude weeds it can overpower.

When choosing a fishing line in thickness, there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer for the grass. You must definitely look into the user’s management, which is attached to the tool, and find information about the requirements for the cutting element.

The use of inappropriate thread can lead to the failure of the tool. The use of too thick thread will entail the overload of the device engine. And the use of too thin thread will significantly increase the wear of the torque.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel in a trimmer for grass. When a suitable fishing line for a trimmer is found and purchased, you can begin to consider the ways to wind it on the coil.

Law mowing instructions

Service

BRAIT motorcosa can last for a long period of time, however, to maintain them in working condition, regular maintenance should be carried out. The schedule of its implementation is clearly spelled out in the operating instructions.

To prepare the fuel mixture, it is necessary to use high-octane pure fuel of the AI-92 or AI-95 brand and mix it with motor oil for two-stroke engines in a proportion of 50: 1.

Every 25 hours it is necessary to clean the fuel and air filters. This will allow the lawnical mower to always give stable speeds.

Upon completion of work, be sure to clean the device from the residues of dirt, dust and grass. This can be done using a jet of water, and then it is necessary to wipe it dry so that corrosion does not begin to form.

change, fishing, line, trimmer, brait

Experience in using electric trimmers

Electric models appeared on our market relatively recently, but begin to actively gain popularity.

The only drawback is the attachment to the power source. During operation, an electric cable should always be behind the device, so that in no case do not run into it.

Before starting operation, be sure to check the condition of the electric cable for lack of damage and insulation disorders.

The manufacturer does not recommend working with wet grass after rain or irrigation to prevent moisture from entering the engine of the Brait trimmer for grass.

At the end of the work, cleaning the remnants of the dirt should occur with a damp soft fabric.

Instructions for the first launch and conservation

The principle of the correct launch sequence is clearly spelled out in the operating instructions. Initially, it is necessary to assemble in the correct order.

Then you have to prepare the fuel mixture in the correct proportion. For this, a special container is supplied with gasoline motorcycle.

Then the engine is running out. It implies the use of a trimmer for grass by half the maximum power. To do this, you need to work out three tanks with a fuel mixture at a minimum load. During this time, the details of the motor are lubricated, they will follow and begin to work as a whole.

During operation on Brait lawmakers, it is recommended to use protective overalls: a tightly adjacent suit, gloves, glasses and shoes with a closed front.

If you do not plan to work on the Brait lawnie for a month or more, it is better to put the car for conservation. To do this, drain the remaining fuel mixture, remove the residues of the dirt, pull out the spark plugs and lubricate all the rotating elements with waterproof grease.

The main malfunctions

Although Brait motorcoses are designed to work in harsh conditions, sometimes small failures happen. Therefore, each owner of the Brait benzos should know ways to correct the most commonly found from them.

If the engine does not start:

  • The tank with the fuel mixture is empty (fuel);
  • There is no spark due to the disconnection of the terminals (fix them);
  • Too much fuel in the combustion chamber (remove the candle and wipe the electrode);
  • The gap in the spark plugs has changed (it is necessary to put it correctly);
  • Not properly mixed fuel mixture (it is necessary to adhere to the correct proportion).

The lawn mower does not develop maximum revolutions:

  • Dirty spark plug (clean or replace it);
  • There is little fuel or it is of poor quality (share or replace);
  • The fuel or air filter was contaminated (clean them);
  • Incorrect tuning of the carburetor (contact the service center).

Below are shown several reviews about BRAIT trimmers from thematic forums:

Installing Trimmer Line. Husqvarna Trimmer

Arthur:

“My grandparents have a small lawn in the village. And earlier, the grandfather of Kosoy regularly mowed there, but the time is already going on and the health is clearly not right. Brait 260 took to facilitate its work. As a great car for me. A reliable and budget trimmer for grass, which copes with a bevel of different grass without problems. It is light and starts without problems. Fuel consumption is completely cheap.

change, fishing, line, trimmer, brait