How to Change a Gas Cable on a Partner Saw
Partner 350 chainsaw repair manual. Partner 350 chainsaw: malfunctions and their elimination
One of the main features of this saw its users note the durability of operation with a minimum number of failures. And yet they occur. To determine why the saw stopped working, you need to make an elementary diagnosis.
If the saw does not start, then:
- there is no spark on the candle;
- no fuel is supplied;
- no air enters.
First, you should check for the presence of a spark: unscrew the spark plug, attach it to the high-voltage wire and put it on the cylinder, pull the starter. If there is a spark, then clean and adjust the clearance on the candle (0.5. 0.65 mm). If it is not, then you need to change: either the flywheel or the coil (magneto). In addition, the candle itself may fail or the high-voltage wire may interrupt.
The next step is to check the fuel supply. To do this, disconnect the feed hose from the carburetor and check its presence. An absence may indicate a clogged fuel filter or feed system. And the carburetor itself may become clogged.
If you do not have experience in repairing and cleaning it, entrust this work to specialists.
If the air supply worsens, the saw should start, but it will work poorly. Remove and rinse the air filter. Replace it only after it has completely dried.
If the saw starts up well, runs at idle and stalls when gas is supplied, the muffler is most likely clogged. Remove, disassemble, wash, put in place and work on.
Easily with your hands, you can also change the guide bar and chain, carburettor, starter, oil pump, ignition and clutch.
And you will be able to replace the broken starter cable after watching this video:
We recommend instructing specialists to perform more complicated chainsaw repairs related to replacing a cylinder-piston group or crankshaft, although if you are well acquainted with two-stroke engines, then this work will not be difficult for you, and Partner chainsaw parts are not a shortage.
To enlarge a picture, click on its thumbnail.
We advise you to regularly monitor the health of the safety group: brakes and catcher. Remember that the saw should be thoroughly cleaned of fine chips. It can not only clog technological holes in the oil pump and other places, but also interfere with the operation of the brake.
Partner 350 Operating Instructions
In this manual you will find not only a detailed description of the saw, but also the basic techniques for working with the tool. We want to draw your attention to the fact that this chainsaw can work on AI95 or AI92 gasoline with the addition of oil for two-stroke engines in a ratio of 1:50.
Adjusting the carburetor of the Partner 340s chainsaw. Pull the Partner 350 chainsaw carburetor yourself
Proper tuning of the carburetor of the Partner 350 chainsaw will eliminate the occurrence of the above problems. This work begins with a performance of disassembly. Adjusting the carburetor of the Partner 350 chainsaw requires knowledge of the design of the work unit.
When disassembling the elements for repairing the carburetor of the Partner saw, it is useful to use the following recommendations:
- When shooting do-it-yourself Husqvarna saw elements, act as carefully as possible. You need to remove each item. The layout of the parts is advisable to carry out in the sequence in which they are removed. This will help make the subsequent assembly process as quick as possible. You can disassemble the unit quickly.
- The top cover is held with three bolts. You will need to carefully disassemble them. Under the removed cover is a foam layer. It performs the air filter option.
- You will need to remove the filter rod in the saw. To do this, dismantle the gas hose.
- To adjust the carburetor of the Partner 350 chainsaw, you need to remove the tip, which is located on the cable. To do this, carefully remove the fuel hose and disconnect the carburetor. Take it off slowly.
- Having completed all of the above steps, you can begin to adjust the carburetor of the Partner 350 chainsaw. Please note that this type of operation is considered quite time-consuming. It will be necessary to configure in stages. Individual elements are small in size. It is important not to lose them when disassembling, configure.
How to change the gas cable On the Chainsaw Partner. Chainsaw repair Partner P351XT. 1 episode. Disassembly
Video: How to Change a Gas Cable on a Partner Saw
If the saw does not start, then:
- there is no spark on the candle;
- no fuel;
- air does not come.
First, check for a spark: unscrew the spark plug, attach it to the high-voltage wire and put it on the cylinder, pull the starter. If there is a spark, clean and adjust the clearance on the spark plug (0.5. 0.65 mm). If this is not the case, you need to change: either the flywheel or the coil (magneto). In addition, the spark plug itself or the high voltage wire may break.
The next step is to check the fuel supply. To do this, disconnect the inlet hose from the carburetor and check its presence. Missing may indicate that the fuel filter or feed system is clogged. And the carb can also be clogged.
If you do not have experience in repair and cleaning, entrust this work to specialists.
If the air supply deteriorates, the saw should start, but it will not work properly. Remove and rinse the air filter. Replace it only after it is completely dry.
If the saw works well, it works at idle and stalls when gas is supplied. The silencer is probably blocked. Take-off, disassembly, washing, installation and operation.
Easily with your hands, you can also change the saw band and chain, carburetor, starter, oil pump, ignition and clutch.
Video Chainsaw repair PARTNER 350 "Part 1"
Partner 350 chainsaw Starts up and Stalls. Related posts
Why does the chainsaw stall when I press the gas?
Hello! If you are on this page, then, most likely, your chainsaw stalls when you press the gas, and you are eager to find out what is happening and what to do about it. Still, I’ll try to help you in this dilemma by examining the more widespread prerequisites for such a collapse, as well as ways to eliminate them.
To begin with, I’ll write for novice users that many chainsaws asks for warming up the engine at idle for about one minute before work. Why the chainsaw starts and stalls. the reasons and. Here the chainsaw has stalled and will not start, or the Stihl chainsaw stalls. Until the engine warms up, the saw may stall when gas is added.
So, if a heated chainsaw can idle, but stalls when loaded, then this means that:
- incorrectly configured or clogged carburetor. the most common case;
- it lacks air, the consumption of which increases sharply with increasing speed. this means that the air filter is dirty (a rare case, because the filter is dirty evenly, because the user first notices the loss of power);
- she lacks fuel, the consumption of which also increases with increasing speed. this means that the fuel filter is dirty (also an infrequent case);
- well, the worst case, if there is excessive friction between the piston and the cylinder wall due to a lack of oil in the fuel consistency. after this operation of the chainsaw, you will most likely fly into the repair of the piston group, because bumps will form on the piston and cylinder walls the work of the saw.
We will analyze these cases separately.
Partner 350 chainsaw will not start. How is the mechanism
Virtually all tools, both foreign (Husqvarna, Makita, Stihl, Partner 350), and Chinese chainsaws, and Russian (Friendship, Urals), are arranged identically. The partner 350 chainsaw will not start. Therefore, finding the reason why the device does not start and stalls is not difficult.
There are four elements in which difficulties may arise:
- The fuel for which the carburetor is responsible;
- Air that flows;
- A spark whose quality depends on the ignition unit.
All of them depend on each other and interact with each other. If any element does not work correctly, then the saw stops working.
To begin with, all instruments start up differently. hot and cold. Two commonly used mechanisms are responsible for this process.
Be sure to see what is written in the user manual. It says that when you turn on you need to make sure that the emergency stop brake is fixed. But to start a saw with a brake is much more difficult, so sometimes it is better not to turn on the brake.
As you can learn from the instructions, inside the case there is a fuel tank and engine, and outside. the saw part (tire with chain), handle and starter.
First you need to figure out exactly how the tool does not start. For example, the saw starts up, but immediately stalls, or loses its power, the quality of the cut.
Perhaps outages occur due to problems in the engine. Stihl (stihl) chainsaw won’t start: how to start. But I would not recommend disassembling it right away. A chainsaw does not start: causes and methods. Do you have a chainsaw? That chainsaw does not start. (Husqvarna). It is better to look for a problem from the simplest option.
Read the same
Assembly of the Partner 350 chainsaw. Characteristics of the Partner 350 chainsaw
This model is in considerable demand among consumers, but most often it is bought by summer residents to work on their sites. They use a saw not only for harvesting firewood, but also in construction.
In general, Partner 350 chainsaws are distinguished by their compact size. They are equipped with a fairly powerful engine. Their main advantages are easy start-up and reliable operation. performed by a quality electronic ignition system and fuel pump.
Using such a chainsaw is completely safe. In it have built a protective system that automatically launch an inertial brake for the chain. In the same mode, its lubrication is also carried out.
With the launch of the chainsaw, the Partner will not have problems even in winter, since it has a fuel primer. The starter drum is equipped with an impeller that helps cleanse itself of dirt. In addition, manufacturers supplied the tool with CCS. This design retains residual particles, and is also used for long-term use of an air filter.
The developers made chrome walls to increase the life of the chainsaw on the cylinder of the piston group. This model also has an ergonomic handle and anti-vibration system.