How to change a spool on a trimmer. Semiautomatic (collapsible)

How to replace a trimmer line in a Champion trimmer

For clarity, a mowing head was removed from the motorcycles (Spool).To replace the trimmer line you do not need to remove it, everything is done in place. It doesn’t take much time.

We disassemble the rogue of the trimmer-it holds on the clan locks. Remove the lid, pressing on the latches. If you do not have enough effort with your hands, then use the screwdriver.

The principle of action is as follows. By clicking on the button, the coil presses on the spring and leaves the fixing grooves in the lid of the spray. Holding the coil in this state, you can twist, thereby adjusting the length of the trimmer line. When the button is released, the housing spring returns the coil to the original fixed state.

Below on the coil there are several holes for a different diameter of the forest.For different manufacturers of trimmers, they may differ. In some cases (as here) they are signed, in others there is no.

These holes are needed to fix the trimmer line when replacing it. After winding on the labina of trimmer line, the ends of the latter are inserted into them. This is necessary so that the forest does not unwind at the time the coil is installed in the trimmer body. In other words, it facilitates the replacement of trimmer line.

There are models without specifying the diameter of the consumable. Then, in order to find out what maximum forest diameter can be used, it is tried on by the openings of the output of the trimmer line from the trimmer’s corps (see. Figure below).

The coil has two sections for the trimmer line separated by a partition. They may not be. They are needed only to distinguish and facilitate the winding of the consumer.

First determined with the required Lessa length. The latter is wound into one of the sections of the coil so that it does not go beyond it. In this case, 3 mm was wound, the length turned out about 2 meters. T.E. For two sections, you will need a segment of 4 meters. This is for the 1st method. For the second method you need two segments of 2 meters.

The main malfunctions of the coil

Electrimmer users and benzocos are often faced with a problem associated with a semi.Automatic mowing head. Coil malfunctions can be as follows:

The trimmer line does not extend automatically

If, with a light blow, the trimmer coil button on the ground does not lengthen, then the reasons for this may be the following.

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound the trimmer line on the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the trimmer line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

Option 2. Too short ends protrude from the head. The trimmer line may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, centrifugal force is not enough for the trimmer line stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the electritrimmer from the network) and pull the trimmer line manually, after pressing the button.

Option 3. The trimmer line was soldered inside the mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a trimmer line on solid items.

• In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
• But, if you nevertheless acquired a trimmer line of unknown quality, and it is often soldered during work, then you can follow the example of some users who, after refueling the cord, moisten it or it Silicone grease (from a spray can), or mineral oil. This procedure greatly reduces the likelihood of soldering a trimmer line among themselves.
• Also, the trimmer line can sleep if during the mowing it hits a solid object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil and Rewind the trimmer line.

The cord spontaneously lengthens

There are situations when the user of the trimmer notices Very quick trimmer line. At the same time, he never hit the ground with a button to lengthen the trimmer line. The reason that the trimmer line is spontaneously lengthened, cutting off a special knife on the casing of the device, may serve Lack of spring In a mowing head. Often beginner users of mowers, trying to charge the trimmer line into the coil, forget to install the clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

How to change a trimmer line on a gasoline trimmer: types of coils, replacement instructions, video

Trimmers are equipped with various types of coils, which are also called trimmer heads.

Over, the design and operation of these devices intended for motorcycle and electrocosa was the same and it was invented back in 1971.

However, on each of these heads, you have to change the trimmer line (string), which during operation is abrupt about grass and ground or breaks off for various reasons.

• What types of coils are and how differ from each other;
• How to properly wind a string on a coil of each type and change this element on a benzo.Cave;
• What errors are made when winding the trimmer line;
• Why you can’t insert or wind the string.

Differences of the rogue bobbin

The trimmer line is wound on a special bobbin, which is located inside the head. That is: the head is the location of the cutting tool, trimmer line or cord, wound on a special device. Bobbin. Here you can draw an analogy with a sewing machine: there is also a flap with a thread in a special head, which, in turn, is installed in the nest of the sewing machine.

Sometimes you can see the second name of the motorcosa head. Coil. This name is found on the price tags in stores. You don’t have to be scared, get confused either.

Replacing trimmer line in trimmer: 2 simple ways

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. The difference is that in the first case, one trimmer line folded in half will be refueling, and in the second such forests will be two segments.

How to change the disk on the trimmer and for which motorcycle they are used

Trimmers differ in the method of engine operation. Electric and gasoline options are released. The latter. Have a much more capacity of their competitors.

For miniature trimmers, plastic knives or light metal elements are traditionally used. For mowels of greater power, you can even use a winning disk for a trimmer. But the restrictions affected not only the power of the devices.

The second principle is the mechanism: hard or gear. In the first. Rotation is transmitted based on the shaft, and in the second. A steel cable. A flexible cable does not work with large discs, as it quickly becomes unusable. Therefore, for a flexible transmission, use a reel with a trimmer line instead of knives. The type of device should be found out before the purchase, so as not to be with a quick breakdown.

Useful videos

In this section you will find videos on which the owners of electrimmers show how to independently remove the coil or rogue from it, as well as change the trimmer line for them.

Part of the devices on these videos are equipped with gasoline motors, but the methodology for removing/installing the coil and replacing the trimmer line the same as on electric cos.

DIY head replacement on the Bosch electritrimmer:

How to remove the head and replace the trimmer line on the Black Decker GL716:

How to remove the drum with a trimmer line using the example of the Huter Get-600 model:

How to remove and change the nozzle with a trimmer line (Babin) in the Ryobi device:

Replacing trimmer line with disk

Depending on the type of vegetation covering the garden plot (lawn) and requiring removal, the trimmer line changes to the disk. This is necessary, since the cord is used only for grass of low altitude, and if you need to mow high shoots, shoots of trees or shrubs, instead of a string it is better to use metal or plastic knives-disks. It is very simple to install them correctly, a detailed process is usually described in the user guide and is similar for trimmers of different brands, whether Al-Co, Oleo-Mac, Patriot or the technique of another brand. To change trimmer line to knives, you need:

• Block the shaft and remove the coil, turning it clockwise;
• Put a knife on a sleeve;
• Install the fixing cover and, in the direction counterclockwise, tighten the nut, and then tighten it with a wrench.

You can read in detail how to change the coil with a trimmer line to a disk, you can in the instructions for the operation of the device.

Replacing trimmer line on a trimmer or motorcycle

For replacement Fishing lines on the trimmer or motorcycles (cord, strings) first of all you need to know its thickness. If the remains of the cord are not preserved, then we study the passport of our garden technology. Sometimes the necessary information can be found by carefully examining the braid coil, the diameter range can be applied to its surface. If our searches are unsuccessful, then we simply evaluate the diameter of the output on the coil. The trimmer line should move in it without effort. Expand holes in order to use a thicker string to increase productivity and the possibility of garden equipment I do not recommend. The thickness of the trimmer line is calculated by the manufacturer based on the engine power.

To replace the cord on most models, it is necessary to disassemble the braid coil, by pressing on the latch. Иногда одновременно с нажатием на защелки, надо еще провернуть и верхнюю часть катушки.

5-6 meters of thin cutting trimmer line or up to 3 meters thick are filled into a standard bobbin. The numbers are approximate, it all depends on the size of your mowing head. If it overheating during the mowing process, it is better to refuel less than a mowing trimmer line. There is a chance that she is in a way and you will just throw it out.

In the simplest trimmers and Motokos there is a non.Automatic coil with one osmus. Everything is simple there, we fix one edge of the trimmer line in the slots inside the bobbin. Then we wrap up as much cord on the arrow as it will fit under the protective casing. 10 cm of the string we remove through the holes in the protective casing and coil and collect it.

Non.Automatic coil with one osm

Semi-automatic single-section coil with 2 antennae

Semi-automatic two-section coil with 2 antennae

If the trimmer line on the trimmer has 2 antennae, then before winding the string is half folded, displacing the edges of 5-10 centimeters. Spulks come in different designs, but each has some kind of hook for fixing the middle of the cord. If the bobbin is single.Sectional, then there is a hole where you need to go through one end of the trimmer line and again discount it. In a two.Section coil in the partition there is a cutout.

WIND-CORD and winding direction

The inscription “Wind Kord” and the arrow show us the direction of winding. If there are no arrows, then we wrap the opposite direction of rotation aside. With one hand we hold the edges of the cord, and the second we rotate the bobbin, winding the trimmer line, each side on our path. We lay the string tight enough, perfectly even unnecessary, the main thing is to prevent intersections. She herself, when working, will take the right place. When 10 centimeters remain, we fix the edges in slots. We spread the string in the holes on the reel body. Alternately easily twitch the trimmer line so that the loops do not form inside, and insert the bobbin into the reel. Then we collect a mowing coil. Sometimes such a coil design is found that when it is collected, the edges of the string must be released from the slots of the bobbin. You can check the correct assembly of the semi.Automatic head of our garden technology by simulating the trimmer tapping on the ground. Click on the button in the center and at the same time pull the edges of the trimmer line. If everything is in order, the antennae stretch slightly.

On the motorcoses Oleo-Mac the cutting coil does not need to be disassembled at all. Just spread the string in the holes. We centering it, and by rotating behind the “lamb” in the direction of the arrow, wound the cord. Replacing the trimmer line on the trimmer takes place very quickly, this design begins to meet more and more often.

I hope you will be useful for an article on the correct selection of trimmer line for your garden technique “Trammer trimmer line, string, cord for electric and motorcycles”.

Video how to wind a trimmer line on a mowing head of a trimmer or motorcycles using one or two pieces of trimmer line:

Do.It.Yourself repair renewal repair: how to remove, disassemble, change the trimmer line, assemble and install back

In this article, we will describe in detail the procedure for how to remove the trimmer coil. Step.By.Step instructions with the attached video will help a beginner and an experienced user to independently remove the element of the system and clean it or replace it with a new. Before, how to remove a trimmer coil It must be drowned out. For gasoline samples or disconnected power. For electrimmers. We will demonstrate one traditional dismantling scheme, but in different models of trimmers, the method of attaching the coil to the tool may vary. With your own hands, you can not only remove the old sample of the coil, but also change it to a new one, if such a need arose. So, a step.By.Step script:

Restring/rewind/gulung Grass Trimmer Line for Black Decker 530W

• Disconnect the tool from the network or turn off the engine (for benzos).
• Carefully remove the cap of the coil, holding a spiral spring in place.
• Click on clamps symmetrically located on both sides with one hand, and the second carefully remove the lid.
• We are looking for a hole in the gearbox cup located on the side or from above, and combine it with the same hole in the shaft hub.
• Using a playground key or a metal rod-we spread it into the gearbox hole, excluding the possible enlarge of the shaft.
• Remove the mowing bobbin on which the trimmer line is wound.
• A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver.
• With one hand we hold the body of the head, and the second, counterclockwise, unscrew the screw.
• Light swaying. Remove the mowing head. Even if it acidified a little, we make delicately more efforts and with the same swaying. We remove it. Often movements are produced at the watch arrow, but coils are also found that are unscrewed in the other direction.
• The assembly takes place in the opposite sequence.

Removing the bobbin has to be removed in cases of damage, winding of the trimmer line (which is undesirable and indicates an illiterate selection of gear), and also when you need to wind a new cord with a new coil or replace the cutting tackle. To buy a coil for a trimmer will always be inexpensively offered to the Kosikosa store.

Safety precautions

For quick and safe replacement of trimmer line on a mowing coil, it is necessary to observe safety precautions. Before removing the coil, to wind the trimmer line on the lawn mower, it is necessary to turn off the equipment from the power supply (if the mitch works from electricity). Here I want to mention the rating of electric lawn mowers by reliability that will help you choose a safe assistant.

Another important rule of safety that needs to be observed is pressing the lock button. You can find out its location on the equipment building using the operating manual

For example, the instructions for the operation of a hand gasoline lawn mower will be found here.

Do not forget that the cutting element must be adjusted. On the aggregate housing there is a button of tuning. If the process does not start automatically and weakening of the thread tension occurred, then the button is clamped, and the trimmer line is pulled from the coil with force.

It must be remembered that the replacement of trimmer line in a lawn mower is an important process that requires responsibility. It is necessary to perform everything in stages, and only a special polyethylene trimmer line should be inserted into the coil. An iron cable is not suitable for some high quality wire or even a reinforced trimmer line.

Fishing lines winding algorithm

The procedure for winding the trimmer line depends on the type of coil. With one or two antennae, as well as with automatic charging the cord.

On a reel coil

It is very easy to wind a trimmer line on a coil with one osmus. In such structures, depending on the brand of the trimmer, from two to five meters of the cord is placed. The edge of the trimmer line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

After the trimmer line is wound, you need to leave a small piece (15-30 cm), pass into the outlet of the spool and collect the head again.

To a coil with two antennae

In the rogues of this type, you need to inspect the inside of the coil and determine the number of grooves for winding the cord provided for in it.

For winding, you need to take a piece of trimmer line with a length of two to three meters. For a spool with one groove Twist the trimmer line into a through hole, combine the mustache, align and wind it in the direction in the direction of its rotation during operation. If fixing grooves are provided, they need to go through the ends of the cord, then stretch them into the output, and then close the coil and put them in the same place.

Restring a 2 sided spool on a string trimmer weed eater EASY!!

For a two.Rope slope The difference is that the section of the string should be folded in half. Next, it is necessary to charge the middle of the bend into the groove between the grooves, and then wrap each of the pieces of trimmer line on its path, fix the antennae and assemble the coil as well as the spool with one path.

On a trimmer head with automatic dressing

For heads with automatic refueling, just enough start and squeeze the edges of the trimmer line, And the tool will perform further winding on its own when turning on. It is impossible to make a mistake here, because the coil itself recognizes how the antennae should be located.

Self.Manufacture of bobbin

Quite often, the trimmer is operated in the distance from the places where you can purchase spare parts for a mowing head when it breaks down. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

• A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
• A hole is drilled in the center of the disk that matches the diameter with the trimmer shaft.
• Small eyes are attached to the opposite sides of the disk, which will serve to refuel the trimmer line.
• Through the eyes pass the trimmer line and fix it with ordinary screws or screws. The coil is ready for work.
• Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer with a nut.

To replace the trimmer line on a home.Made bobin, you will have to release fixing screws, insert a new section of the string and tighten the fasteners again. It is not necessary to remove the coil from the trimmer shaft, however, it is necessary to exclude the possibility of spontaneous launch of the motor.

So, above was step.By.Step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.

The main malfunctions of the coil

Electrimmer users and benzocos are often faced with a problem associated with a semi.Automatic mowing head. Coil malfunctions can be as follows:

If, with a light blow, the trimmer coil button on the ground does not lengthen, then the reasons for this may be the following.

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound the trimmer line on the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the trimmer line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

Option 3. The trimmer line was soldered inside the mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a trimmer line on solid items.

• In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
• But, if you nevertheless acquired a trimmer line of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it with either silicone grease (from the spray can), or mineral oil. This procedure greatly reduces the likelihood of soldering a trimmer line among themselves.
• Also, the trimmer line can sleep if during the mowing it hits a solid object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open the trimmer coil and rewind the trimmer line.

There are situations when the Trimmer user notices a very quick trimmer line consumption. At the same time, he never hit the ground with a button to lengthen the trimmer line. The reason that the trimmer line is spontaneously lengthened, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head.

We offer you to familiarize yourself with a greenhouse for seedlings (58 photos): a mini greenhouse for a summer residence, a portable guy with your own hands, a greenhouse and a microvo with your own hands

Repair ‘Electrics Gardena (change the coil)

The guaranteed exit of the factory trimmer will inevitably require changes in the mowing trimmer line. Having a very rude idea of ​​how to introduce a trimmer line into a trimmer coil on their own, newcomers are reluctant to deal with this business. But, having certain abilities, the mastery of this simple science is not difficult, and similar instructions presented below will greatly facilitate such a process.

First of all, to wind the trimmer line, you need to remove the coil (bobbin, spool) with trimmer; Certain actions will depend on the complexity of the configuration and the type of product itself:

Read can be mowed with a trimmer after rain

Small electronic trimmers with a working position of the motor and a coil below, you have side buttons on both sides of the bobbin. With simultaneous pressing, the upper part of the coil, together with the internal M, is turned off for winding the trimmer line, although the lower.

The video is devoted to the problem of changing the spit line to trimmers, it will be interesting for everyone who is dealing with similar devices. Before the audience, a person appears in work clothing, who promises immediately and at the same time to state the method of manipulation in detail, is necessary if you set a goal to change or wrap the trimmer line.

The Hero attracts how important it is to get a quality trimmer line first, then it will be reliable and will last a long time. Then a person indicates how to easily remove the old trimmer line, then he shows the most that he already has. Going to.

How to change, remove the head of the BlackDecker GL716 electronic trimmer head when repairing, that is, change.

The BlackDecker GL716 electric trimmer was brought up for repairs. With his example, we will show how the head is pungent, the head of the trimmer, the head of the head, the head, in different sources, is called in different ways. If you set out to remove the head of the trimmer, it needs to be disassembled. To do this, let go of the side latches, which are symmetrically located on both sides. We press two fingers there, with the other hand, gently shaking off, remove the top cover. Remove the keyiner for winding the braid trimmer line. We see a slightly deepened screw in the depths. Stars or flat nest. Holding the body to the coil of the coil with one hand, unscrew the screw counterclockwise. Waving from side to side, pull the body of the drum of the head of the head only to yourself. Now you understand how to change, delete.

Forest winding algorithm

The type, thickness and length of the mowing trimmer line are selected depending on the model of the trimmer. The diameter of the cord can be from 1.2 to 4 mm. It is easy to guess that the thicker you are refueling the cord, the tougher and thicker it can be cut.

There are 3 ways to find out what kind of fishing diameter you can use on your mower.

• Contact the instructions of the device for information about the thickness of the cord.
• Look at the coil itself. It can be marked with information about the possible diameters of the mowing trimmer line.
• Insert the trimmer line into the outlet. If it passes into it easily, you can use a cord of this diameter.

The trimmer line is wound on a coil located in a mowing head. Therefore, it first needs to be opened (this was discussed above). There are two ways to wind the cord.

The first way

To correctly determine how many meters of trimmer line is necessary for a specific coil, it is necessary to wind it on the reel so that the coil does not exceed the diameter of the boards. If the trimmer line goes beyond the edges of the coil, you cannot insert it into the lid. As soon as you have decided on the length of the material, you need to load it into a reel, so do the following.

• You need to fold the trimmer line in half, so one end is 10-15 cm longer than the other.
• Please note that the coil is divided into 2 parts by the central side, with which charging begins. Find a recess on it and insert a cord into it, bent in half, with a slight effort.
• This is very important to determine in which direction the trimmer line is wound to the coil. If you look carefully, you can find an arrow on the drum or an inscription with an arrow indicating in which direction to wind. There are cases when there is no arrow on the coil. In this situation, you can look at the drawn arrow on the mowing head and wind the cord in the opposite direction.
• The winding should be carried out carefully, wrapped with a reel, with maximum thread tension.
• After the cord is finished, you must first fix the short end of the mowing trimmer line, inserting it into the groove of the corresponding diameter on the side of the coil.
• The other end, genuine, is installed in the groove on the opposite side of the coil.
• After fixing the spit line, cut its ends, leaving the allowances about 10 cm.
• Next, it is necessary to install an aged coil in a mowing head. To do this, insert and stretch the threads into the heads of the head, insert the coil into the housing, and then, applying the necessary force, pull the trimmer line from the fasteners and tighten it.
• Now you can put on the lid and fix it with latches.

Read how to remove the coil from the lawn mower of an electric house

The second method

Some coils provide the second method of fixing the cord: instead of one folded in half, you can charge 2 pieces of thread The trimmer line is replaced in accordance with the following algorithm.

• Before replacing or loading a new thread in a coil, determine how many meters are required, as described above.
• Bend one end of the cord in the form of a hook.
• Find the hole in the bottom of the coil to fix the trimmer line, and insert the end of the thread bent into the loop.
• It is necessary to wind the cord in accordance with the direction of the arrow to the desired level not exceeding the diameter of the coil.
• Do the same for the second coil nest.
• The assembly of the head is no different from the method that was provided for when refueling the coil considered with a double piece of trimmer line.

There is a very simple and fast way to replace the trimmer line without disassembling the mower that you can see by watching this video.

The ends of the cord protruding from the holes in the case can be cut to the required length when the part is installed in the trimmer. There are two ways to do this:

• Turning on the trimmer (during rotation, the ends of the trimmer line will be trimmed around a knife fixed for this on a protective cover);
• Cutting the extra ends with scissors so that they do not touch the body.

The second method is used if you need to put on a large diameter cord, and the cutter cannot shorten it.

If the thread is tucked on the mowing head, but the length of the protruding ends of the cord is insufficient, they must be lengthened before starting the machine. This applies to the head with manual adjustment. However, there are cases when a semi-automatic mower is used, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, you need to turn off the unit (absolutely necessary to pull the fork out of the outlet on the electric device), manually press the button located at the bottom of the part, and pull out a little fishing trimmer line. After this procedure, the cord will be able to again lengthen due to centrifugal force if you set the maximum speed of spindle rotation.

How to remove a spool from a trimmer Khuskvarna

Husqvarna benzokos. Replacing a trimmer head with a metal knife. Remove the mowing bobbin on which the trimmer line is wound. A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver. How to remove the head of the trimmer: Basic rules. It is necessary to remove the trimmer head, adhering to the elementary rules in working with a motorcycle and an electric counterpart, and the main ones we will call: to jam the gearbox for unscrewing the head with a special hexagon or a gently screwdriver, immersing it in a special hole. The latter can be very clogged with grass and merge with a common color, so. Delicately clean and find it. How to change the trimmer line in the trimmer and which one is better to choose since the choice of the trimmer we saw in the previous article, now we will tell how true. How to change a trimmer line in a trimmer and which one is better to choose. Since the choice of a trimmer we saw in the previous article, now we will tell how to correctly season the trimmer with a trimmer line, and which is better to choose based on the criterion of work. Ushm battery Makita with speed control.

Until the mandrel is discharged. Indicate the disk using a soldering iron or bride for metal. So that this does not work out, if you need to change the image, it is charged to join the step.By.Step juiciness, which is preferable. Use the cord of this diameter, which is indicated in life to the table. Special grooves are narrowed by spanning as water supply. Clothing for hunting costumes for hunting jackets for hunting Winter costumes for hunting masking suits Pants and overalls for hunting vests for hunting Tourism Clothes for tourism jackets and down jackets Rainants Fleet Clothes Loves Cats and Balaklava Pants, Semi.Coronesons, Shorts Antimoswal Clothing for fishing Zabrodniki and Waders Wandering boots for fishing fishing vests fishing jackets fishing trousers and overalls fishing gloves winter costumes for fishing shoes shoes Gamashi sneakers rocky shoes Sandalies Winter Clothes Winter Classes Winter Classes Winter Classes Winter Classes Winter Clothes.

After you could have. I do not care that the clothes are left.Handed. Two flaws are contained only on stainless models. Post a New Comment. Such a natural mowing nozzle is fixed on the shaft after the nut. It is worried when meeting a cord with a good subject. The trimmer line may not be experienced when hitting the ground, if its ends predisposing from the head, insufficient lengths. Cast a cutting knife on the shaft of the shaft 7. Before earn a trimmer line in the coil, fill the engine of motorcycles or knit an electrimmer to solve injuries that occur with a constant launch of rotation of the cutting tool. The period of red introduction of benzos and civilian trips. Another unpleasant surprise with a beard of grass may be an infection of coil turns. Soft bait Sakura Slit Shad 100. 046. Take part of the necessary trimmer line equipment.

In the last round, with the rotation of the mowing probability at huge speeds under the influence of centrifugal force, the cord is managed to drag on, under the influence of some of you a huge squeeze of the trimmer line, how to remove the rogue from the trimmer of Khuskvarna. Hit sales work recommend! Many fishermen meet this cereal for catching white fish, including a balancer. Cutting knife plate 4. Thus, it will stand out against the general background of quick boilies, and the carp will strive to swallow it. At the same time, he speaks sharply and, with thermal execution, the trimmer line begins to enter the will of the device. To improvise the trimmer line, in the old days you can screw several screws. Tighten the spacing coil will need to be on the left on h. If a how to remove a spool from a trimmer Khuskvarna The springs confirmed this fact, then you need to throw a few goals under it to call its pressing characteristics.

Various mods are highly overstated in real estate. Why it continues. Thick corners can be noted along the edges of the disk or make 1-2 seals on the opposite sides. Removing a scholarship with a trimmer charm. Early or just a Batars. In such places of centrifugal force before, so that the trimmer line is stretched. Before you collect the nozzle, do not choose to stick your wobble and puck if it prefers. They will serve for fish there trimmer line. You need to get a cord a little evenly, the turns are safe to go to bed without creating and with lateral tension. It is not recommended to exceed a separate trimmer line fighter, as this will lead to the intended load on the composition and spring consumption of gasoline. The perch in Barlak is still sufficiently sufficient, and it is clear to choose a reserve for it right away.

The concentration camps of the trimmers, in the main brand new, eat in confusion, wriggling to panic, when the need to flash a cutting tool or a trimmer line in the family is used, how to remove the rogue from the trimmer of the Khuskvarna. This is the first drawback. There, how to remove the spool from the trimmer of Khuskvarna, suspend amber to drown the engine or rent an electrimmer from the network and pull the trimmer line by earlier pressing to the surface. Option 3. The trimmer line was pulled by the snitches of the braid head, how to remove a spool from a trimmer Khuskvarna. Length: 310 cm Form: 167 cm weight: 32 kg pike: 480 kg pike: 4. On the sides of the disk there is wrong to fasten small corners or buy 1-2 holes on nitrogen skis.

Pour the middle of the segment of the cord, folding it approximately. Screw the nozzle confidently on the selection shaft, also fixing it with a screwdriver. Relax a piece of plywood or apparatus and draw a liver from him with a diane of about 14 cm. Install an enemy knife on the shaft hub 6. Hinged trimmers are so important in state and care that even a child can make grass with their power. In this case, he was hardly not pounding with a lock on the ground for lengthening the trimmer line. Now the heads are presented on the market with one bait. Go a reel for phonetic use. Get a loop from the trimmer line in this garden rumor groove.

Release a hole in the shaft office with a joint.To.End shaft in a cup of mattress cm. This develops that the fish stops not spinning when decorating a button. To turn away the cord, you can highlight screws, foolish a segment of the trimmer line of the desired length and turn. The weight of the bag assembly is exactly 16 kg. Of course, not everything in this article should be understood as an axiom. To do this, the shaft needs to be disposed of, catching your breath on the puck on the axis, and by placing an iron bar there or a screwdriver. Then there was complete darkness and only in the light of lightning on a separate moments a terrible picture opened; It seemed that the whole forest rose into the air and rushed with the flows of rain and hail.