How to change the dexp trimmer attachment

How to tie a float. basic fastening methods

One of the most popular types of fishing is definitely float fishing. And here the question of the correct attachment of the float is of particular importance.

Two points

Fastening the float at two points is considered the most reliable. At the same time, the correct working position is maintained not only during splashdown, but also in the process of casting and playing with bait.

In order to attach the float at two points, you need to use a ring and a cambric to hold the fishing line in the middle of the mounting ring, and a plastic ring must be attached to the antenna itself. The line is threaded into it in advance.

There are 3 designs that are mounted on the basis of double fasteners:

Pole Floats. In this design, a lower cambric is put on the keel so that it protrudes slightly. This is necessary in order to avoid accidental friction in the future. Next, you need to determine the length of the fishing line itself, taking into account the hook, after which you need to lower it, fixing it with two additional cambrics. As a result, you will get 3 cambric, which will be even more reliable. In this design, the float itself will be fastened by the spring.

Stick Floats. This design differs from the others in the diameter of the keel itself. The lower point is fixed with one cambric with the help of a spring, and if it is absent, then you can use the antenna, but you need to fix it by its thin part. To make the connections more reliable, the cambric is best glued.

One point

It is the most popular method, as it maximizes the sensitivity of the float, as well as its maneuverability. Mainly used for fastening wire and cambric.

A piece of wire is passed through the lower ring of the float, and then the ends are twisted and inserted into the cambric, through which the fishing line was previously threaded.

“Kremkus”

This type of stopper appeared relatively recently and thin lines and threads are used in its formation.

It fits simply: we fold the segment in half, 4-5 times (we select the number of revolutions) we wrap around the main fishing line, then we intertwine the ends with each other the same number of times, moisten and tighten. With a successful selection of threads or fishing line, it holds better than previous ones.

Summing up, we can say that the angler should choose the optimal one from all the variety of ways to attach the floats to the fishing line. It is necessary to take into account the properties of the tackle, and the nature of the reservoir, and, of course, the properties and habits of the intended trophy.

Line inside the float

There are floats, inside of which a tube is passed, a fishing line is inserted into it. A float with such a mount is suitable for fishing at depth. The fishing line is inserted inside, then the keel should be put on, after the fishing line is fixed at the end of the keel with the same cambric.

The line runs inside

How to swap out trimmer head and grass blade

Thus, summing up what has been said, I conclude: the method of attaching the float to the fishing line of the fishing rod depends on the depth of fishing, distance and method of fishing.

Распаковка триммера DEXP MK-1060 / Unboxing DEXP MK-1060

Duncan

The requirements for the material of the assembly are the same as for the previous version. Here we take a larger loop, apply it to the main line, press it and make 5-6 turns inside the loop. Then we moisten and tighten with the necessary effort. With all the simplicity of the scheme, this option is more complicated than the previous one, especially with soft threads. At the same time, some anglers prefer it.

“Clinch”

For knitting it, a woolen thread or fishing line is taken with the same diameter as the main one. The length of the piece should be approximately 20 centimeters. You can do more. it will be easier to tie a knot.

Fold the segment in half, forming a small loop, put it on the fishing line and make 5-6 turns around it with one of the ends, holding the loop. Then we pass this wrapped end into the loop, moisten the structure and tighten the knot, after selecting the force of passing the fishing line through the stopper, cut the ends, leaving at least 2-3 centimeters. This length will allow you to pass freely through the rings of the rod. This principle applies to other types of knitting as well.

Stick floats

Stick Floats. differ in different keel diameters. The lower point is attached with only one cambric. Attached to the spring. If there is no spring, then the cambric should be put on the thin part of the antenna. To strengthen the connection, the cambric must be glued. In terms of reliability, the spring is better.

How to replace line in any trimmer

How to replace line in any trimmer
So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of fishing line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!
When choosing a fishing line for your motor scythe (gasoline or electric), you should dwell on some points, which we will talk about in detail.

Line diameter.
Engine power determines which maximum line diameter can be used for a given braid. For example, the manufacturer of an electric trimmer with a power of up to 1 kW recommends using a line of ø2 mm, and at values ​​of about 500 W. only ø1.5 mm. Also, the manufacturer of any heavy duty curved bar trimmer recommends using a ø2mm line.
The gasoline engine is more durable than the electric one, so you can use thicker line there, which means stronger line, which allows you to cut more grass and work longer.
For grass cutters with a straight bar, you can select the line according to the following simple algorithm: the diameter in millimeters corresponds to the engine volume in tens of cubic centimeters. For example, for a Husqvarna 128R lawn mower with an engine capacity of about 25 cm3, use a line of ø2.5 ± 0.2 mm. For more powerful hedge trimmers with volumes of more than 40 cm3, only the geometric dimensions of the outlet openings of the mowing head. no more than 4 mm are the limitation of the diameter of the line.
So, a thin fishing line (about 1.5 mm) cuts well cultivated lawn grass, and a thick one (for example, 3.0-3.5 mm) successfully destroys weeds and even young shrubs.

Line shape.
The simplest and cheapest to manufacture is a round line. However, the requirements of ergonomics and environmental protection limit its use. due to its physical properties, it creates an unacceptably high level of noise (which is comparable to the noise of the engine itself). This is the classic Husqvarna round line or Oregon RoundLine or Chipmaster.
To reduce the noise produced by the line, it is given a special shape. they make it spiral like Oregon DuoLine Plus (noise reduction by 15 dB) or with special transverse grooves like Husqvarna Whisper (-8 dB).
Following the school laws of physics, the “working” part of the line during the mowing process is only the end surface, not the side surface. However, to increase the “sharpness” of the line, i.e. to increase efficiency, the cross section is changed from round to faceted: star-shaped, square or square with teeth. Oregon StarLine, Nylsaw or Flexiblade.
For example, according to the calculations of experts, Oregon Nylsaw line, due to its square profile, is 27% “sharper” than its round counterpart, which clearly affects the increase in mowing speed.

# replace # any # diameter # shape # trimmer # lawn mower # for # spool # mow # repair # lawn mower # replacement

Video How to replace the line in any trimmer of the O T V E R T K A channel: the home master’s channel

How to install muffler tips?

The muffler attachment, or rather the exhaust pipe, is used for decorative purposes and serves as an excellent element of car styling. Nozzles come in a wide variety of shapes: oval, round, rectangular, multifaceted, double or single outlet, and other model options. Typically, car exhaust tips are made from polished stainless steel.

What happens when you install the muffler head on your car? Instead of a banal exhaust pipe, an aesthetic nozzle will be visible from the outside, which will significantly improve the appearance.

Attachments come in different shapes, but they can serve:

• exclusively for aesthetic decorative purposes;
• for styling, and with the ability to change the sound of the engine in the direction of increasing low (sports) frequencies;
• for styling and for turbine sound emulation.

There are options for nozzles with an integrated removable whistle, in such options you will have the opportunity to choose whether to ride simply with a nozzle or with a nozzle that changes the sound of your engine.

How to install a nozzle on an exhaust pipe?

Muffler attachment installation is very simple. The scope of delivery of the nozzle usually includes a fastening element. In fact, you simply screw the tailpipe to the exhaust pipe with a few bolts. Installation time of the nozzle takes 1-2 minutes.

If you are afraid that your attachment screwed in this way may fall off during driving and from vibrations, then you can grab it by welding. If you weld the nozzle, then if you want to remove it, you will have significantly more work to dismantle it.

How to install muffler tips?

Muffler tip selection

To choose a muffler nozzle, you should adhere to two rules. (This does not take into account the aesthetic side, since everyone chooses for himself the option that he likes best).

• Firstly: the purchased muffler nozzle must fit the exhaust pipe of your car in diameter. Before buying a nozzle, be sure to consult the seller for the correspondence of the nozzle to your make and model of the car;
• secondly: you must be fully aware that the size of the nozzle may require you to modify the rear bumper of the car in the area of ​​the exhaust pipe. This will increase the cost of installing a special design and unsuitable size. True, such attachments most often look prettier.

There are options for attachments that do not require modification of the rear bumper and easily fit in the underbody space. Sometimes a special thermal protective cover is installed between the bumper and the nozzle. It is placed in cases where the nozzle is too close to the rear bumper.

In general, before choosing a muffler nozzle, take care if it can easily fit with the rear bumper. If not, then get ready for the appropriate improvements.

CarEx muffler tips (tips). Select

Unimix Muffler Nozzles. Select

Распаковка триммера DEXP MK-560FCPD / Unboxing DEXP MK-560FCPD

When is the use of knives relevant?

When using lawn mowers in summer cottages, the fishing line is the most popular attachment. It has a low price, is suitable for different trim heads, and is safe to use. The disadvantage of using a fishing line is that it is convenient only for mowing low growth. In other situations, the string will kick in immediately, regardless of whether a petrol or electric trimmer is used. In addition, vegetation is wound around the spindle, which creates significant resistance on the shaft and leads to its breakage. It can also cause piston system failure in lawn mowers or engine burnout in trimmers.

Therefore, for mowing tall or hard vegetation, various attachments are used. So, for harvesting high and coarse grass, thin shoots of trees and shrubs, it is better to install and use a disc. This nozzle clogs much less often, which contributes to the greater wear resistance of the equipment.

On a note! Due to the fact that the engine of trimmers and battery models is less powerful than on lawn mowers, therefore the use of discs is more relevant for gasoline mowers.

Rules for replacing knives on the grass trimmer

If the trimmer disc is used regularly, it will need to be removed from time to time and sharpened or replaced with a new one. This part can be made of metal or plastic, have a different number of blades, but the replacement process remains the same. over, this procedure is similar for equipment from different manufacturers, be it Carver or Huter, but slight differences are possible. It is quite simple to change the knife on the trimmer if you follow the safety precautions and know the correct procedure, the description of which can be found in the user manual. The whole process of replacing step by step, as well as the method of self-sharpening knives, will be described in this material.

How to install a disc on a trimmer

Attaching the blade to the trimmer is very simple. For this, a complete wrench is used to disconnect the cutting attachment and a pin that locks the gearbox. The procedure is as follows.

• First of all, the electric trimmer should be disconnected from the network, the petrol trimmer should be simply turned off. Disconnect the protective cover and move to the side.
• Next, you need to align the holes on the gearbox and the shaft in order to insert a pin into them and block the drive.
• If a spool with line was used, it must be unscrewed clockwise.
• Then you need to find a nut to twist the knife.
• The next step is to install the knives. Trimmer owners often wonder which side to put the disc on. This must be done so that the marking with numbers and letters is on top.
• Then you need to put the boot on top, and above it. the fixing nut, which must be tightened tightly with a wrench.
• The last step is to install the protective cover.

As you can see, the procedure is very simple and the same for many brands, be it Stihl or Husqvarna equipment.

On a note! If the owner of the device wants to replace the disc back on the line, you can install the reel with it in the same way.

Disc sharpening

Regardless of the quality of the disc, over time it becomes dull and begins to chop grass poorly. If the knives are still relatively new, and replacement is impractical, you can sharpen them yourself.

Important! For sharpening, only those discs that are not soldered from hard materials are suitable. Such parts are thrown away, and new ones are acquired instead.

To sharpen discs, you must:

• disassemble the trimmer, remove the knives;
• carefully inspect the disc. if cracks are found, it is better to replace the part with a new one, since its further operation is unsafe;
• bent blades can be gently bent with a hammer;
• given the size of the disc, you need to choose the right file for metal, this will ensure more convenient work;
• sharpen all upper cutting edges of the discs at an angle of 30 °;
• reassemble the trimmer in reverse order.

To sharpen the disc, you can use an emery machine at low speeds with a medium grit grinding wheel. With such a tool, the process will move much faster. For safety, you need to wear gloves on your hands, and a protective mask or goggles on your face.

So, for mowing grass on gasoline and trimmers, plastic and metal discs of various shapes and with a different set of blades are used. They are selected in accordance with the type of work performed and the size of the cultivated area. If the blades on the mower are dull, it is easy to sharpen them or change them yourself. Despite the simplicity of the procedure, you need to be careful and remember about safety, so as not to injure yourself through negligence or damage the equipment. A more detailed description of replacing the knives in relation to a specific trimmer model can be found in the operating instructions or on the manufacturer’s official website. For clarity, the general scheme of the process is shown in the video.

Disk selection criteria

Blades

The number of blades is important when solving diverse tasks. So, to grind the grass, two or three pieces are enough. To harvest hay, it is necessary that there are four to eight blades on the disc. To destroy small shoots of trees and shrubs, instead of blades on the disks, there should be a large number of small teeth.

Lawn mower disc features

Knife discs are available in plastic and metal, as well as in various shapes to perform diverse tasks.

• Two-, three- and four-bladed knives with pronounced blades are used for mowing grass and tree growth. However, they are not suitable for making hay, as they grind the shoots, chopping them several times.
• Massive four-blade discs are designed not only for clearing the ground from grass, but also for mowing hay. They prevent repeated cutting of the shoots, thus making them suitable for harvesting for the winter.
• Discs with cutting edges around the perimeter are relevant for beveling reeds and reeds. These knives are very heavy. a necessary quality to cut through thick stems.
• Professional saw blades for hedge trimmers and lawn mowers for cutting small trees and bushes.

Plastic knives are used as an alternative to metal discs. They do not need to be firmly fixed in the head, but they rotate as a result of centrifugal force. The strength of plastic knives is high, so the service life is quite long.

On a note! The advantage of plastic discs is that, hitting an insurmountable obstacle, they bounce off, and repeated contact does not occur.

Other vulnerable mechanisms

With prolonged use, other elements of equipment are also subject to wear:

• the pistons get dirty and burn out;
• the crankshaft breaks;
• cracks appear in the carburetor and engine housing.

In all these cases, a complete replacement of old parts is required. The complexity of restoration work depends on the degree of damage to the equipment.

Changing the line in the trimmer

If a fishing line is installed in the device, then it looks like a spool with wound thread. Replacing it is easier than the rotor, since the instructions are in each new material.

Loosening other fasteners

It is necessary to tighten bolts and other connections if, during use, the machine begins to shake, make strange sounds and rattle. This indicates the wear of the body and engine mountings, more common in gasoline models, which is associated with the peculiarities of their operation. Also, a foreign object can penetrate into the nodes, blocking the aerator roller.

Breakage of cutting elements

Knives and line are the most vulnerable consumables in lawn mowers. Material wear can be recognized by the uneven cut of the stems. There are other problems as well:

• loosening of the knives. there is a whistle and vibration;
• damage to the knives. the mower will jerk and malfunction.

You can get rid of these problems by changing the materials or performing their correct settings. You can perform a simple mechanical repair of the lawn mower with your own hands by following the instructions for disassembling the unit.

Steps for removing the cutting knife

If in the process of repairing an electric lawnmower with your own hands you cannot unscrew the bolt, you need to hit it several times with a hammer, applying little force.

The main thing is not to put too much effort so as not to disrupt the part.

Features of the repair of gasoline and electric engines

Rebuilding critical components such as engines is a job that requires experience and skill. There can be a lot of reasons for malfunctions. from damage to the cord to failure of carburetors, starters and other elements.

Important! It is impossible to repair the engine without a professional tester with voltage indication.

Step-by-step identification of electric motor problems:

• Determine the voltage of the network, it must correspond to the operating capabilities of the equipment. If it differs from the norm, a stabilizer is required.
• Visually assess the condition of the cord and plug, if there is damage, the cable must be changed and insulated.
• Diagnose the power button: remove it, following the instructions, check it with a multimeter.
• Evaluate the capacitor. If it is swollen or oxidized, a complete replacement will be required.
• The electric motor is checked: the quality of the winding, integrity, if there is carbon deposits, it is better to take the equipment to the service center.

Also, some motors have brushes that need to be cleaned with sandpaper.

Drive system problems

This element in gasoline and electrical devices is significantly different. The main part of the system is the motor, among the faults of which are distinguished:

• strong vibrations during use;
• decrease in engine power;
• quick shutdown of the mechanism after a short work;
• lack of reaction to the start command.

Also in the drive system there is a shaft, which often fails when working on uneven surfaces, when colliding with stones. It is possible to repair the engine on your own, but this puts the technician at serious risk.

Common mechanical problems

Regardless of whether it is front, rear or four-wheel drive on a particular mower, it contains parts such as: line or knife, transmission mechanism, ejection and collection device, handles, body and wheels. All of them are subject to certain damage.