How To Change The Line On The Trimmer Petrol Stihl

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing wall.

The line is inserted into the slot

In a certain direction earlier, the fishing line is wound. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does NOT change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end the segment that is located at the bottom of the coil, i.e. The one closest to the fixing holes.

This tip is placed in the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing line, fixed earlier in the holes of the reel, pops out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to set it back to the trimmer and you can start Mowing the grass.

It should be repeated, it is not necessary to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

The tip so that they do not hit the trimmer cover can and should be trimmed.

How to wind the line around the trimmer cutter head or lawn mowers. Method 2. two segments

Two coiled line pieces

Fundamentally, it does not differ from the method The only difference is two wound pieces of fishing line, instead of one.

The end of each segment is folded

The end of each segment is folded.

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We start reeling the line

They cling to it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.e. The one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. The one that will overlap the bottom section.

The bottom line is reeling

The tip is made into the holes in the trimmer spool body. They are pulled to clicks, which means that the line has come out of the clips.

The tip is threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

How to wind line on a Stihl trimmer. Changing the line in the trimmer: 2 easy ways

In this manual, we will walk through the entire replacement process step by step. Going forward, there are two ways to line the trimmer spool. There are fundamental differences. the difference lies in the fact that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.

Preparing for replacement

We disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, it is not necessary to remove it, everything is done locally. It does NOT take long.

We disassemble the trimmer spool. it rests on the latch-latches. Remove the cover by pressing on the latches. If you do not have enough effort with your hands, then use a screwdriver.

The spool consists of the following:

Spring case
Cover with locking latch
Button coil

The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. By holding the reel in this state, you can twist it by adjusting the length of the line. When the button is released, the body spring returns the coil to its initial fixed state.

Disassembled trimmer spool

On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (as here) they are signed, in others there is.

These holes are needed to fix the line when replacing it. After winding on the grandmother’s fishing line, the ends of the latter are inserted into them. This is necessary so that the scaffold does NOT unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.

Holes for fixing the line

There are models without specifying the diameter of consumables. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for the outlet of the fishing line from the trimmer spool body (see Figure below).

Fitting on the holes of the line output

The reel has two line sections separated by a baffle. They may not exist. They are needed only to distinguish and facilitate the winding of consumables.

Two sections for line

First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. THOSE. For two sections, you need a 4 meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.

Determining the required line length

Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.

Special designation on the reel

If such designations were not found, then you need to Pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Bobbin case designation

How to wind line around the trimmer head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

Line problems

Users of trimmers, both gasoline and electric, sometimes have problems with the cord. “Advanced” Owners of mowers easily cope with difficulties in automotive products, understanding why this happens, and for beginners, these are problems that have no rational explanation. But in fact, everything is solved quite simply. The most common problems that happen with the line are as follows.

Option

In this embodiment, the head is screwed onto the gearbox shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, follow 2 easy steps.

Insert a screwdriver into the hole and lock the shaft.
Grasp the head body and start turning it clockwise. Torque in this direction follows because the thread cut on the shaft is left.

Types of trimmer heads

The grass mowing head is a cylindrical body in which a spool (bobbin) is inserted with a fishing line (cord) tucked in it. This design can be installed on both gasoline and electric trimmers. The heads differ in the way of threading and feeding the cord and are of 3 types.

Automatic. Cord feed is performed after the user Decreases engine RPM. Although the automatic line feed is convenient if large volumes of work are performed, there is one drawback in such bobbins. a high whine consumption.
Semi-automatic. The use of this type of heads does not require the user to perform complex manipulations. The principle of their operation is designed in such a way that the cord lengthens automatically while the apparatus is operating at full speed. It is enough to lightly hit the ground with the trimmer head (this removes the blocking of the cord), and the line is pulled out of the bobbin due to centrifugal force, after which it is cut to the required length with a knife located on the protective cover.
Manual. To lengthen the cord, the device must be stopped, after which the line is pulled manually.

Based on the above, semi-automatic bobbins are the most optimal option. It should also be borne in mind that the coils for the trimmer are single-string (used only for trimming the grass) and two-string, which are used for mowing tall grass and small, thin-stemmed bushes.

No cord feed, coil does NOT spin

An automatic or semi-automatic head should feed the line without stopping the machine. But if She does not come out, then the reasons may be as follows:

The line in the reel is not wound correctly, because of which the latter does NOT spin;
The cord is not wound evenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortion)
Too short ends of the thread come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the line is NOT fed (it is recommended to always adjust the length of the cord by pulling it slightly before starting the unit)
The line is stuck together (will be discussed later).

High cord consumption

Basically, the cord runs out quickly if you hit the ground frequently with the semi-automatic head or press it down hard. The spool is unlocked, and the line, lengthening, is cut with a knife. Another reason that the cord runs out quickly is improper operation of the machine with an automatic head: the user often cuts the engine speed when mowing. But as we remember, the automatic head is designed in such a way that it is with each decrease in revolutions that a new portion of the line is supplied, so it is quickly consumed.

Option

To remove the trimmer head, you will need to completely disassemble it.

To remove the cover that covers the inside of the head, you must press on the latches (latches) located on both sides.
After removing the cover, you will see a spool that needs to be removed from the body. Some spools have a spring under the bobbin, which must be carefully pulled out to avoid losing it in the grass.
When you remove the bobbin, you will see a slotted screw for a Phillips or flathead screwdriver in the center of the case. It is possible that there may be a hex bolt or a nozzle “star”.
Using a screwdriver, selecting the required bit (bit), it is required to Unscrew the bolt (counterclockwise).
After removing the fasteners, grasp the body of the part and, swing it in different directions, Remove it from the gearbox shaft.

How to remove and disassemble a coil

Before starting the process of changing the cord, it becomes necessary for trimmer users to remove and disassemble the coil. Let’s see how to do it.

The trimmer mowing head consists of several parts: a cover, a spring (not on all models), a spool with a cord and a cover.

In trimmers, 2 options for mounting the mowing head are most often used.

How to change the line to the trimmer

The trimmer is the most common machine used for cutting grass and small bushes. This device is distinguished by its simplicity in service, simple operation during operation, and due to its low weight, even women can handle it. It is no secret that the correct selection of cutting tools is required for high-quality performance of work on mowing grass. As the latter, special cutting attachments (discs, knives) or trimmer heads with a fishing line inside are used in trimmers. Nozzles and line are expendable tools, but if the knives can be sharpened, then when the line is used up, it must be replaced. In this article, we will tell you in as much detail as possible how to properly replace the fishing line.

The line is flying out

The reason that the cord unwinds after starting the unit may also be due to the weakening of the spring inside the head. In addition, there are times when the mowing head flies apart when the machine is turned on, and the spring installed in it is lost. Inexperienced users do NOT notice the absence of a spring and assemble this unit without it. Therefore, the cord does NOT hold, and under the influence of centrifugal force flies out.

The first way

To correctly determine how many meters of line is required for a particular reel, it is necessary to screw it onto the bobbin so that the skein does NOT exceed the diameter of the sides. If the line sticks out over the edges of the spool, you will NOT be able to insert it into the casing. After you have decided on the length of the material, it must be threaded into the bobbin, so do the following.

It is necessary to fold the fishing line in half, so that one end of it is 10-15 cm longer from the second.
Please note that the bobbin is divided into 2 parts by the central edge, from which charging begins. Find a groove on it and insert a cord into it, bent in half, put a little effort.
It is very important to determine in which direction the line is wound onto the reel. If you look closely, you can find an arrow on the bobbin or an inscription with an arrow indicating in which direction the winding should be carried out. There are times when there is no arrow on the coil. In such a situation, you can look at the arrow drawn on the mowing head and wind the cord in the opposite direction.
Winding should be done carefully, turn by turn, with maximum thread tension.
After the laying of the cord is completed, you will first need to fix the short end of the fishing line, insert it into a groove of a suitable diameter on the side of the reel.
The second end, the one that is longer, is attached in a groove on the opposite side of the bobbin.
After fixing the fishing line, cut off its ends, leaving about 10 cm allowances.
Next, you need to install the loaded bobbin into the mowing head. To do this, alternately insert and pull the thread into the outlet holes of the head, place the bobbin in the casing, then, applying the required force, Pull the fishing line out of the fixing grooves and tighten it.
Now you can put on the cover and fix it with the latches.

Cord breaks

If the line breaks frequently, this may be due to the following reasons:

Stones, small branches and other solid obstacles come across in the grass;
Users are mowing the grass right next to the fence, and if it is mesh, it cuts off even faster “antennae”;
Poor cord quality (it is recommended to purchase a quality one)
The outlet holes in the mowing head are worn out, which causes the line to be erased on the sharp edges of the bushings and break off (a complete replacement of the part will be required).

What can be used instead of fishing line

Many users of trimmers ask themselves the question: what can be used to replace the default cord used in this kind of machines? Begin unsafe experiments by installing metal or copper wires, metal ropes or strings, and ordinary fishing line in the mowing head.

If you install a metal cable instead of a fishing line, the trimmer turns into a dangerous device Not only for the user, but also for those around. This fact is explained by the fact that during the operation of the unit, the steel cable will gradually be triggered, its ends will unravel, and small pieces of wire will scatter in different directions at high speed.

And if you accidentally hook your or someone else’s leg while working with a steel cable (wire), then a strong and deep tissue incision, and in some cases amputation of your toes, is guaranteed. The manufacturer does NOT use nylon for THESE purposes in vain, since it is light and strong enough, and when it comes off it does not fly far away and cannot cause injury.

Of course, you can use fishing line in the trimmer instead of the standard one, but this will add extra trouble to you, since it wears out quickly, tears, mows slowly and is NOT suitable for cutting tough grass. In addition, when carrying out work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a conventional line is justified if the user is going to mow the grass near the fence, especially if he is from the netting. In this case, in order to protect the standard, and sometimes expensive, line from wear and tear, it is changed to a fishing line, which is not a complaint. Usually, in order to change the line to the line, it must be selected The greatest thickness. 2-3 mm.

The thread does NOT hold

It happens that the thread is unwound if the spring in the semi-automatic head has weakened. The line is constantly extended and cut with a knife installed on the cover, which increases its consumption. To check this, remove the cover and turn on the unit. If the line “climbed”, spring replacement is required.

How to remove and disassemble a coil

Before starting the process of changing the cord, it becomes necessary for trimmer users to remove and disassemble the coil. Let’s see how to do it.

The trimmer mowing head consists of several parts: a cover, a spring (not on all models), a spool with a cord and a cover.

In trimmers, 2 options for mounting the mowing head are most often used.

Option

To remove the trimmer head, you will need to completely disassemble it.

To remove the cover that covers the inside of the head, you must press on the latches (latches) located on both sides.
After removing the cover, you will see a spool that needs to be removed from the body. Some spools have a spring under the bobbin, which must be carefully pulled out to avoid losing it in the grass.
When you remove the bobbin, you will see a slotted screw for a Phillips or flathead screwdriver in the center of the case. It is possible that there may be a hex bolt or a nozzle “star”.
Using a screwdriver, selecting the required bit (bit), it is required to Unscrew the bolt (counterclockwise).
After removing the fasteners, grasp the body of the part and, swing it in different directions, Remove it from the gearbox shaft.

Second way

Some reels have a second method of securing the cord: you can charge 2 pieces of yarn instead of one folded in half. The line is replaced according to the following algorithm.

Before you change or load a new thread into the spool, determine how many meters it will take using the method described above.
One end of the cord Fold into a hook.
Find the hole at the bottom of the bobbin for fixing the line, and insert the end of the thread bent in a loop into it.
It is required to wind the cord according to the direction of the arrow to the required level, and not exceeding the coil diameter.
Do the same for the second bobbin compartment.
The assembly of the head does not differ in any way from the method that was given when it was considered threading the bobbin with a piece of line folded in half.

For Shtil lawn mowers, there is a very simple and quick way to change the line without disassembling the mowing head, which you can get acquainted with by looking at this.

The ends of the cord protruding from the holes in the casing can be cut to the desired length when the part is installed in the trimmer. This can be done in two ways:

Turned on the trimmer (when rotating, the ends of the line will be cut into a knife, fixed for THESE purposes on the protective casing)
Cutting off the excess ends with scissors so that they DO NOT touch the casing body.

The second method is used if a large diameter cord had to be supplied, and the edging knife cannot shorten it.

If a charge was made to whine into the mowing head, but the length of the protruding ends of the cord is insufficient, then they must be lengthened before starting the machine. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do NOT automatically lengthen. In this case, it is necessary to turn off the unit (on electrical apparatus, it is imperative to unplug the plug from the socket), manually press the button located at the bottom of the part, and pull out a little line. After this procedure, the cord can again be extended due to centrifugal force, if you set the maximum spindle speed.

How to change the line to the trimmer

No cord feed, coil does NOT spin

An automatic or semi-automatic head should feed the line without stopping the machine. But if She does not come out, then the reasons may be as follows:

The line in the reel is not wound correctly, because of which the latter does NOT spin;
The cord is not wound evenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortion)
Too short ends of the thread come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the line is NOT fed (it is recommended to always adjust the length of the cord by pulling it slightly before starting the unit)
The line is stuck together (will be discussed later).

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to change line for gasoline trimmers. Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

How to insert line into the trimmer spool? Instructions

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

How to change line to trimmer?

The trimmer is considered to be the simplest and most convenient device for cutting grass and other types of low vegetation. It should also be noted that it is this device that is in demand among consumers today. Let’s figure out today how to change the fishing line on it, and do it without outside help.

You now have a trimmer. this is great, because the device is inexpensive and at the same time very convenient and effective. Time passes, and if you used this unit all the time, then the line becomes unusable, which means that it is time to replace it. Taking it to specialized repair points is one of the options to change the fishing line, but why pay for it if you can carry out this process yourself.

The advantages of the trimmer are:

Very easy to maintain
Easy to operate, anyone can handle it
At the price. affordable, which means that everyone can buy it

So, in order for the trimmer to be effective. It is necessary to choose the right cutting type attachments or special heads. If the cutting attachment can be sharpened, then in the case of a fishing line, nothing of the kind can be done, it will only need to be changed.

It is worth noting that the fishing line tucked into the reel is called the cord and the part in question can be installed on a trimmer, which runs on electricity or on gasoline.

When you need to change the fishing line to a trimmer, you should start this process by disassembling the coil itself, you simply cannot do without this to achieve your goal. It turns out that first we shoot, and then we disassemble the coil to get to the line.

The mowing type head is NOT simple in design, it has several parts, namely, springs (this part may not be found in all models), a casing, a cover and a bobbin with fishing line.

If your unit is powered by electricity, before starting the disassembly process, it is imperative that you turn it off from the network. The mowing head can be attached to the trimmers in several ways, which will determine how the disassembly process will be carried out. So, we proceed to removing the trimmer head (you need to understand that complete disassembly will be required to carry out this process):

We are looking for clamps, which are located on both sides of the lid, press on them and remove the lid, which is a protective barrier for the head, which is located under it.

There is a spool under the cover, and it is this that needs to be removed. It should also be noted that some models are also equipped with a spring, which is located directly under the bobbin and if there is one, it should also be pulled out. Because it is small and you can lose it.
There is a screw under the bobbin, which can be unscrewed either with a Phillips or flat screwdriver (also depends on the model and manufacturer). Some models have a bolt instead of a screw, so keep that in mind. The screw or bolt will need to be Unscrewed.
After the fasteners are removed, we carefully grasp the housing and remove it from the gearbox shaft.

The second option for disassembling the head is useful if it is screwed directly onto the gear shaft. In order to remove the part in question, you will need to fix the shaft. A metal rod or a thin screwdriver is useful here:

We stick the twig into the hole and fix the shaft
After that, it is necessary, holding the head body, to scroll it, moreover, it is necessary to do it only clockwise, but not against it. You need to understand that the thread in this case is left-handed, and that is why scrolling should be carried out in the direction of.

Now let’s start winding a new line. First you need to choose the thickness and, of course, the length of the cordon, usually these parameters are selected depending on the model. Basically, you need to purchase a new line that is similar to the old one in all respects. If, for any reason, you are not satisfied with the parameters of the old one, then decide on your own and buy the one that, in your opinion, will be the best option.

You also need to understand that the thicker the fishing line you choose, the thicker the grass it can mow, but the diameter of the fishing line is considered a universal option in this case Corresponding to the size of 2 mm.

The purchased new line must be wound around the head, which is why the first stage of our process was its analysis. When the head is open and you are holding a new cord in your hands, we proceed to winding it:

First, we decide how much fishing line we need for winding. To do this, we wind the fishing line in such a way that it does not go beyond the reel itself.
Now we fill the line into the spool. for this we fold the line twice, and one end should be shorter than the second, by about 10 cm.
Since the bobbin itself consists of two parts, and the central side is the dividers, you need to find a groove on it, in which the fishing line will be inserted. It is worth noting that in order to carry out this process, you will need to make an effort.

The spool will indicate the direction of the line winding, so be careful. We wind it up carefully and take our time. Attaching one end, which is shorter, into the groove. Located on the side of the coil and in the other groove Attaching the other end.

Now we Install the coil head in place and fix all this in the reverse order. Your trimmer now has a new line to help you cut your grass quickly and easily.

Share tip: “How to change line to trimmer?”

Sources:

http://tehnika.Expert/dlya-sada/trimmer/kak-pravilno-namotat-lesku.html
http://tehnika.Expert/dlya-sada/trimmer/kak-pravilno-namotat-lesku.html
http://san-lider.ru/leska/kak-pomenyat-lesku-na-benzinovom-trimmere-video.html

Grass Trimmer change, line, petrol, stihl, trimmer