How To Change The Line On The Trimmer Stihl Fs55

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to insert line into the trimmer spool? Instructions

How To Change The Line On The Trimmer Stihl Fs55

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Coil with two working tendrils

In this type of spools, you should find the number of grooves for winding the line, lying on the inside of the reel:

One groove. both tendrils are wound together along one groove;
Two grooves. each tendril is wound on a personal groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded into them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixation of the antennae and assembly of the coil is similar to the one-groove option discussed above.

The first execution of this procedure, perhaps, will seem long and rather labor-intensive, but over time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

We wind the fishing line

Sluggishly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the spool. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Preliminary preparation

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

How to correctly replace the line in the mowing head, reel of STIHL FS 55 lawn mowers Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

Small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on an evenly smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special lamb: in such designs, you should hold the spool in a stationary position with one hand, and turn the wing nut counterclockwise to fix the Bobbin on the bar. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
Electronic and petrol trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a leisurely rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

For the second and third version of the coil, the suspension from the structure is disassembled by different methods. In the bobbins, the lamb is turned out from the lamb, in the coils, the latches are pressed from the latch, and one part of the coil is released from the other. How to tuck the fishing line into how to properly cheap fishing line. 2. On your site. If the halves of the spool are threaded, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

We wind the fishing line

Coil with one working tendril

The most common option and easy sequence of actions:

The dimensions of the spool and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
A small section of the line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole on the outside of the reel.
The bobbin halves are assembled and put on the trimmer bar.

How to put line in the Stihl.FS-38 mower

I took out the mower from the barn, but there was NO line in it, I had to put the line and on the occasion removed a small

Cord breaks

If the line breaks frequently, this may be due to the following reasons:

Stones, small branches and other solid obstacles come across in the grass;
Users are mowing the grass right next to the fence, and if it is mesh, it cuts off even faster “antennae”;
Poor cord quality (it is recommended to purchase a quality one)
The outlet holes in the mowing head are worn out, which causes the line to be erased on the sharp edges of the bushings and break off (a complete replacement of the part will be required).

Second way

Some reels have a second method of securing the cord: you can charge 2 pieces of yarn instead of one folded in half. The line is replaced according to the following algorithm.

Before you change or load a new thread into the spool, determine how many meters it will take using the method described above.
One end of the cord Fold into a hook.
Find the hole at the bottom of the bobbin for fixing the line, and insert the end of the thread bent in a loop into it.
It is required to wind the cord according to the direction of the arrow to the required level, and not exceeding the coil diameter.
Do the same for the second bobbin compartment.
The assembly of the head does not differ in any way from the method that was given when it was considered threading the bobbin with a piece of line folded in half.

For Shtil lawn mowers, there is a very simple and quick way to change the line without disassembling the mowing head, which you can get acquainted with by looking at this.

The ends of the cord protruding from the holes in the casing can be cut to the desired length when the part is installed in the trimmer. This can be done in two ways:

Turned on the trimmer (when rotating, the ends of the line will be cut into a knife, fixed for THESE purposes on the protective casing)
Cutting off the excess ends with scissors so that they DO NOT touch the casing body.

The second method is used if a large diameter cord had to be supplied, and the edging knife cannot shorten it.

If a charge was made to whine into the mowing head, but the length of the protruding ends of the cord is insufficient, then they must be lengthened before starting the machine. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do NOT automatically lengthen. In this case, it is necessary to turn off the unit (on electrical apparatus, it is imperative to unplug the plug from the socket), manually press the button located at the bottom of the part, and pull out a little line. After this procedure, the cord can again be extended due to centrifugal force, if you set the maximum spindle speed.

Line winding algorithm

Depending on which trimmer model is used, the type, thickness and length of the line are selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you fill the cord, the harder and thicker grass it is able to cut.

There are 3 ways to find out which line diameter you can use on your mower.

View information on the thickness of the cord in the instructions for the device.
Look at the bobbin itself. It can contain information about the possible diameters of the line.
Insert the line into the outlet. If it easily passes into it, then a cord of this diameter can be used.

The line is wound on a reel in the mowing head. Therefore, you first need to open it (this was discussed above). There are 2 ways to wind the cord.

The first way

To correctly determine how many meters of line is required for a particular reel, it is necessary to screw it onto the bobbin so that the skein does NOT exceed the diameter of the sides. If the line sticks out over the edges of the spool, you will NOT be able to insert it into the casing. After you have decided on the length of the material, it must be threaded into the bobbin, so do the following.

It is necessary to fold the fishing line in half, so that one end of it is 10-15 cm longer from the second.
Please note that the bobbin is divided into 2 parts by the central edge, from which charging begins. Find a groove on it and insert a cord into it, bent in half, put a little effort.
It is very important to determine in which direction the line is wound onto the reel. If you look closely, you can find an arrow on the bobbin or an inscription with an arrow indicating in which direction the winding should be carried out. There are times when there is no arrow on the coil. In such a situation, you can look at the arrow drawn on the mowing head and wind the cord in the opposite direction.
Winding should be done carefully, turn by turn, with maximum thread tension.
After the laying of the cord is completed, you will first need to fix the short end of the fishing line, insert it into a groove of a suitable diameter on the side of the reel.
The second end, the one that is longer, is attached in a groove on the opposite side of the bobbin.
After fixing the fishing line, cut off its ends, leaving about 10 cm allowances.
Next, you need to install the loaded bobbin into the mowing head. To do this, alternately insert and pull the thread into the outlet holes of the head, place the bobbin in the casing, then, applying the required force, Pull the fishing line out of the fixing grooves and tighten it.
Now you can put on the cover and fix it with the latches.

Option

In this embodiment, the head is screwed onto the gearbox shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, follow 2 easy steps.

Insert a screwdriver into the hole and lock the shaft.
Grasp the head body and start turning it clockwise. Torque in this direction follows because the thread cut on the shaft is left.

Option

To remove the trimmer head, you will need to completely disassemble it.

To remove the cover that covers the inside of the head, you must press on the latches (latches) located on both sides.
After removing the cover, you will see a spool that needs to be removed from the body. Some spools have a spring under the bobbin, which must be carefully pulled out to avoid losing it in the grass.
When you remove the bobbin, you will see a slotted screw for a Phillips or flathead screwdriver in the center of the case. It is possible that there may be a hex bolt or a nozzle “star”.
Using a screwdriver, selecting the required bit (bit), it is required to Unscrew the bolt (counterclockwise).
After removing the fasteners, grasp the body of the part and, swing it in different directions, Remove it from the gearbox shaft.

High cord consumption

Basically, the cord runs out quickly if you hit the ground frequently with the semi-automatic head or press it down hard. The spool is unlocked, and the line, lengthening, is cut with a knife. Another reason that the cord runs out quickly is improper operation of the machine with an automatic head: the user often cuts the engine speed when mowing. But as we remember, the automatic head is designed in such a way that it is with each decrease in revolutions that a new portion of the line is supplied, so it is quickly consumed.

No cord feed, coil does NOT spin

An automatic or semi-automatic head should feed the line without stopping the machine. But if She does not come out, then the reasons may be as follows:

The line in the reel is not wound correctly, because of which the latter does NOT spin;
The cord is not wound evenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortion)
Too short ends of the thread come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the line is NOT fed (it is recommended to always adjust the length of the cord by pulling it slightly before starting the unit)
The line is stuck together (will be discussed later).

Types of trimmer heads

The grass mowing head is a cylindrical body in which a spool (bobbin) is inserted with a fishing line (cord) tucked in it. This design can be installed on both gasoline and electric trimmers. The heads differ in the way of threading and feeding the cord and are of 3 types.

Automatic. Cord feed is performed after the user Decreases engine RPM. Although the automatic line feed is convenient if large volumes of work are performed, there is one drawback in such bobbins. a high whine consumption.
Semi-automatic. The use of this type of heads does not require the user to perform complex manipulations. The principle of their operation is designed in such a way that the cord lengthens automatically while the apparatus is operating at full speed. It is enough to lightly hit the ground with the trimmer head (this removes the blocking of the cord), and the line is pulled out of the bobbin due to centrifugal force, after which it is cut to the required length with a knife located on the protective cover.
Manual. To lengthen the cord, the device must be stopped, after which the line is pulled manually.

Based on the above, semi-automatic bobbins are the most optimal option. It should also be borne in mind that the coils for the trimmer are single-string (used only for trimming the grass) and two-string, which are used for mowing tall grass and small, thin-stemmed bushes.

Complain about ?

We wind the fishing line

How to properly change the line for a trimmer. Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device like a trimmer exists in several variations:

As it is clear from the name, the trimmer types differ markedly from each other. But regardless of the type of this tool, its cutting element may be a fishing line. Of course, the line tucked into the trimmer reel is NOT infinite. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line for a trimmer, and will be discussed in this article.

Line selection

In order for the threading of the line into the trimmer head to be successful, it is important NOT to select the consumables. The thicker the cord you tuck in, the thicker and tougher the grass it can cut. Often a universal line is used, the diameter of which is 2 mm. You can choose a diameter suitable for the mower in the following ways:

Refer to the instructions that came with the trimmers for line thickness information.
Pay attention to the bobbin itself. Sometimes information about the possible diameters of the fishing line is applied on it.
Another option is to try inserting a cord into the exit hole. If it easily goes through it, then the selected line diameter is suitable for use.

Trimmer reel

You can select the cord thread by the type of engine. If the line is too thick, the rotation resistance will increase. in this case the engine will overheat and will soon fail. Helpful hints:

For an electrical device with a motor less than 500 V, a 1.3 mm thread is suitable. If one is not found, then you can use a 1.6 mm line. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
In a gasoline trimmer, the mower shaft matters. For the folded version, a 2 mm cord is often used. If the shaft is straight, then install the thread 2.4-2.5 or 3 mm. The thickest line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of section of the cord thread. Some popular options:

The most common lines are round. They mow fresh grasses well, but they cope worse with shrubs, dead wood.
Twisted (spiral) cord is NOT very strong, but is good for thin young grass.
Serrated thread with sharp edges ideal for large weeds in neglected areas.
You can mow the lawn more evenly with rectangular, star or square trimmer lines, but they are not very durable.
Strongest. two-piece inner-core round cord.

Types of trimmer line

Please note that you cannot use wire, metal strings and cables, as well as ordinary fishing thread instead of fishing line. The device will be dangerous to both the user and others. So the cable or similar products will gradually begin to work, as a result, their ends will unravel, and small pieces will scatter at high speed.

Removing and disassembling the coil

The mowing trimmer head consists of a cover, a spring (not available in every model), a spool with a cord, a cover. Before proceeding to disassemble the coil of the electrical unit, be sure to disconnect the trimmer from the mains. The disassembly method depends on the attachment of the mowing head. First option:

To remove the cover that covers the inside of the head, press on the latches (latches) that are located on both sides of the head.
Remove the cover, under which you will see the spool. Remove it from the body. Some trimmer spools have a spring under the bobbin, which must also be carefully pulled out.
Soaked in the bobbin, you will see a screw in the center of the case. Unscrew it with a screwdriver.
After removing the fasteners, take the body of the part and, swing it in different directions, remove the gearbox from the shaft.

In the second version, the trimmer head is screwed onto the gearbox shaft. To remove it, you need to fix the shaft. For this, such devices have a hole through which a thin screwdriver or metal rod is inserted. Brief instruction:

Insert a screwdriver into the special hole, then lock the shaft.
Grasp the body of the head and start twisting it. This should be done clockwise, because the thread on the shaft is left.

Winding the line to the reel

How to insert line into the trimmer spool? Instructions

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Sources:

http://trubymaster.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://tehnika.Expert/dlya-sada/trimmer/kak-pravilno-namotat-lesku.html
http://yasenevo-flowers.ru/navesnoe-oborudovanie/kak-pravilno-pomenyat-lesku-na-trimmere.html

Grass Trimmer change, fs55, line, stihl, trimmer