How to clean the grass trimmer

How to clean your pants?

Trousers are a favorite item of men’s and women’s wardrobe. They are comfortable and practical, perfect for both everyday wear and holidays. In the process of wearing, trousers often get dirty, various scuffs, shine, stains from oil, chewing gum, coffee, juice and other products can appear on them. You can get your favorite pants dirty anywhere, in transport, on the street, at work, at home, but getting rid of the stains is sometimes much more difficult. It is good if the dirt is minor and the stains are easily washed off, but what to do when a regular wash is powerless. Do not be upset, let alone throw away your favorite pants. After all, there are a lot of household chemicals that are able to cope with severe pollution. Such products are convenient and easy to use, it is enough to read the instructions on the packaging and carry out the washing or cleaning correctly. Do not forget about folk remedies, which over several decades have accumulated many recipes that allow you to remove even the most severe pollution. Folk remedies for stain removal are easy to use and popular with thrifty housewives.

Which method to choose for cleaning trousers directly depends on the material of the pants. If the trousers are made from natural fabrics, then you need to be careful. Some folk remedies can completely ruin the material. In such cases, it is better to use dry cleaning services or choose a more gentle cleaning method. Let’s consider several methods of cleaning trousers that need to be cleaned of animal hair, chewing gum, greasy stains, grass, we will also tell you how to remove shine from trousers, because its presence creates the look of old and dirty trousers, which are long overdue for “rest”.

How to properly clean your trousers from various dirt

How to remove wool from trousers?

Pets live in many houses, which delight us with their affection, but sometimes the pet falls out of favor, especially when you have to clean the house and clothes from wool.

Easily removes wool from trousers and regular wide tape. You need to take a small part of the tape and stick it to the outer surface of the material, you can wind it around your hand, but only so that the sticky part of the tape is outside. Then roll the sticky side over the pants. When a sufficient amount of wool, dust, lint has accumulated on the adhesive tape, you need to replace the adhesive tape and continue to clean the trousers.

It is easy to remove wool from trousers with ordinary rubber gloves. Wear gloves and run your hands over your pants.

Cleaning wool with rubber gloves

General recommendations

This advice should be followed by users of any lawnmower, petrol or electric.

• Store the device in a dry place.
• It is better to hang it on the wall, on a special mount.
• After each use, the device must be cleaned of dirt and mowed grass, inspected for damage and wiped off the surfaces with a soft cloth.
• Before work, you need to check whether the bolts fastening the parts of the unit are well tightened, especially the fasteners of the working head.
• It is better to wash the grass juice from the reel immediately after mowing.
• It is necessary to monitor the amount of fishing line and the condition of the metal or plastic attachments. The line must be of the correct diameter (for the bobbin being used and the type of thicket). The blades of discs and knives must be sharpened, and the reversible attachments must be turned over for uniform grinding of the teeth.

On a note! Grass is often wrapped around the reel, rod and gearbox. this slows down the rotation of the spindle and puts unnecessary stress on the motor. Long stems and leaves should be removed from the trimmer immediately after mowing or during breaks.

The turns of the cord on the bobbin must be uniform, without overlaps. The line must be wound in the right direction and in the recommended amount. There are marks on the spool: arrows to indicate direction and marks to indicate a border.

Large shrubs, trees, fences and other solid obstacles should be cut around the perimeter, with the trimmer turned with the cover towards the obstacle. Otherwise, the line consumption will increase, and the blades will become dull very quickly.

Also, the ignition coil may be punctured in electrical equipment. In this case, the lawn mower will not start, or it will start and work intermittently, and then it stalls, or it will not start at all when it is hot.

You can check the coil’s serviceability in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body. If there is no spark when you jerk the starter, or it appears every other time, you need to change the coil.

How to clear the grass trimmer

The summer time has come, and lawn-mowers as usual rattled on the personal plots. Great tool, powerful and mobile. With the help of a gasoline trimmer, you can cut the grass and get rid of the dried weeds. However, there are times when the lawn mower will not start, work intermittently or not at full capacity. There is certainly no time for work! And as they say, you pull the starter handle more than you mow.

Launching difficulties arise not only for seasoned lawn mowers, but also for new ones. How to be in this situation? There is only one way out. to heed the advice of experts and take advantage of their practical experience.!

If everything is in order with the electrical equipment, then we check the carburetor.

The trim tabs are fitted with vacuum carburetors. When disassembling, cleaning or washing it, you need to be extremely careful. in no case do you disassemble the lower part of the carburetor, where the primer is located. The air filter (visible when you remove the protective cover from the carburetor) must be washed with detergents. Best for washing dishes. After drying, put it back. We wash the carburetor with clean gasoline and blow through all the holes with a pump. We also wash the fuel line filter, then dry and collect everything. Usually, after all the manipulations, the trimmer starts to work.

A thin cable instead of a fishing line, is it worth it to be put on the lawn mower?

This idea occurs to almost everyone who had to mow 10 acres of tall grass. At first glance, the idea seems like a good one. The cable is stronger than the line and does not wear out so much. However, not all so simple.

The numbers mean the following: one part of the oil takes fifty parts of gasoline. Hence: 1000 ml (1 liter of gasoline) is divided by 50, we get 20 ml, that is, 1:50.

Thus, you can calculate the composition of the fuel mixture (gasoline / oil) in any proportions. To add oil to gasoline not “by eye”, you can advise to take a 20 ml medical syringe, draw oil into it and “inject” into a container for preparing a fuel mixture.

In no case should you store gasoline in a plastic container from under water. When mixing the fuel mixture, a static charge accumulates, you can “catch” a spark.

Therefore, at gas stations it is not allowed to fill gasoline in plastic cans, only in metal ones. Before pouring gasoline into a metal canister, it is better to put it on the ground, this way static is removed from the body.

But there are situations when simple manipulations with the lawn mower do not help. The engine still won’t start. In this case, we are going to check the power supply and ignition system, guided by the rule “the engine does not work if there is nothing to burn or nothing to ignite”.

If you put a cable instead of a fishing line, without the possibility of releasing it, securely fixing the two ends of the cable and cutting them off by welding (a drop of melted metal keeps the cable from unraveling). Such a tool “knocks down” the grass at a time. Cuts off shoots up to about a finger thick. Not as afraid of stones as a disc. There is, however, a problem: when worn, pieces of cable thread break off, and these twisted wires remain in place of the mowing. Stepping on them can cause injury.

But the pieces of the cable left on the field are half the trouble. The fishing line, breaking off, weakens the dynamic shocks on the transmission and the engine, the cable does not give such an opportunity. The result is rapid wear on lawn mowers.

During the engine running-in period (this is approximately the work of the trimmer on 2-3 tanks), the amount of oil can be increased. For example, mix it with gasoline in a 30: 1 ratio.

A small amount of oil mixed with gasoline leads to increased wear of the cylinder-piston group. An excess of oil in the mixture, although not so fatal, is also harmful. Coking of the piston rings, rapid formation of carbon deposits in the combustion chamber, and a drop in engine power may occur. In addition, the muffler mesh screen is coked. Therefore, some users (after the end of the warranty period for the trimmer) recommend dismantling it.

The gasoline used in the lawn mower is AI 92. The brand of gasoline is precisely specified in the operating instructions. You should not try to “force” the engine by pouring 95th gasoline into it. This can cause overheating, erratic trimmer operation and breakage.

It is not recommended to leave fuel in the trimmer tank during extended shutdowns. It is better to end the working day with the entire mixture completely exhausted. If this is not done, then, since the gasoline will evaporate from the engine overnight, and a thin film of oil will remain, the carburetor jets may become clogged. This will cause difficulty the next time you start the engine.

It is also necessary to observe safety precautions when storing fuel. Many people pour gasoline into a plastic water bottle. Is it worth doing this?

gas trimmer loves cleanliness. It is necessary to monitor the cleanliness of the air filter and fuel. Gasoline bought at a gas station is better to stand for 2 days and pass through the simplest filter. a piece of bike cloth.

We check the electrical equipment as follows:

We unscrew the candle, inspect the gap between the electrodes. We can set the correct gap between the electrodes in the “old-fashioned” way. We take the razor blade, break it in half and insert a homemade probe between the electrodes. If the blades fit tightly, then the gap is perfect.

We put the cap of the high-voltage wire on the candle and lean the candle against the metal surface of the engine. We pull the starter several times. If the spark hits one point well, then the gap is adjusted correctly. If not, the spark is weak or “wandering”, then it is necessary to re-adjust the gap between the electrodes.

See the trimmer instructions for the continuous running time of the lawn mower. On average, we mow for 15-20 minutes, after which we turn off the trimmer and let it cool for 3-5 minutes. Weather conditions also affect the duration of continuous operation. In hot weather, when mowing tall grass, thickets of weeds, under heavy load, the trimmer overheats faster.

Many lawnmower problems arise from improperly prepared fuel mixtures. In two-stroke engines, lubrication is carried out with a special oil (not ordinary engine oil!), Mixed with gasoline. If the oil is not mixed with gasoline, the lawn mower will quickly fail. Mix the oil / gasoline in the proportion indicated in the trimmer instructions. Usually it is 1:40 or 1:50.

The question often arises: the proportion of 1:50 is how much oil and gasoline?

Preparation for wintering

In order for the gas trimmer not to lose performance during the period of inactivity, you need:

• inspect the device for cracks, chips, bent parts;
• detach the cover and cutter head;
• drain the fuel from the tank and turn on the device to use up the remaining gasoline;
• thoroughly wipe / rinse the rod, handle, casing;
• remove the coil or knife;
• clean the gearbox and add oil to it;
• inspect and wash filters.

Then remove the spark plug, pour a little (20 ml) of engine oil into the hole and gently crank the engine shaft several times with the starter to distribute the lubricant to the cylinders. After these manipulations, you need to insert the candle back, but do not twist it all the way. This procedure (except for adding oil) must be carried out once a month while the device is not being used.

Important! The engine will not corrode if the trimmer is stored in a dry place where the air temperature remains constant and does not drop below freezing. If this is not possible, the motor should be wrapped in a cloth.

If the rod is disassembled, the joints must be lubricated (for example, with lithium) to protect the metal from rust.

If you put a cable instead of a fishing line, without the possibility of releasing it, securely fixing the two ends of the cable and cutting them off by welding (a drop of melted metal keeps the cable from unraveling). Such a tool “knocks down” the grass at a time. Cuts off shoots up to about a finger thick. Not as afraid of stones as a disc. There is, however, a problem: when worn, pieces of cable thread break off, and these twisted wires remain in place of the mowing. Stepping on them can cause injury.

But the pieces of the cable left on the field are half the trouble. The fishing line, breaking off, weakens the dynamic shocks on the transmission and the engine, the cable does not give such an opportunity. The result is rapid wear on lawn mowers.

Any braid has a knife on the protective cover, which cuts off the excess fishing line after winding, and the cable is no longer cut. If part of the cable breaks off, then the result is an imbalance, increased vibration. Bottom line: shaft drive bearings break.

In no case should you store gasoline in a plastic container from under water. When mixing the fuel mixture, a static charge accumulates, you can “catch” a spark.

Therefore, at gas stations it is not allowed to fill gasoline in plastic cans, only in metal ones. Before pouring gasoline into a metal canister, it is better to put it on the ground, this way static is removed from the body.

But there are situations when simple manipulations with the lawn mower do not help. The engine still won’t start. In this case, we are going to check the power supply and ignition system, guided by the rule “the engine does not work if there is nothing to burn or nothing to ignite”.

If everything is in order with the electrical equipment, then we check the carburetor.

The trim tabs are fitted with vacuum carburetors. When disassembling, cleaning or washing it, you need to be extremely careful. in no case do you disassemble the lower part of the carburetor, where the primer is located. The air filter (visible when you remove the protective cover from the carburetor) must be washed with detergents. Best for washing dishes. After drying, put it back. We wash the carburetor with clean gasoline and blow through all the holes with a pump. We also wash the fuel line filter, then dry and collect everything. Usually, after all the manipulations, the trimmer starts to work.

A thin cable instead of a fishing line, is it worth it to be put on the lawn mower?

This idea occurs to almost everyone who had to mow 10 acres of tall grass. At first glance, the idea seems like a good one. The cable is stronger than the line and does not wear out so much. However, not all so simple.

How to fix a grass trimmer

Many have faced the problem when something does not work after a long period of inactivity. Garden tools also fall into this category. The household electric grass trimmer is used 2-3 times a year. The rest of the time it is stored in the garage. What to do if in the spring you find it inoperative or it breaks down, unable to withstand the loads?

Lawn trimmer design

To fix a lawn trimmer, you need to understand its design and understand what could break. It consists of:

• housings with an electric motor and a starting system;
• rods with flexible shaft and handles;
• cutting system with protective cover.

This is a traditional design where the body and cutting system are counterweights. But you can also find electric lawn trimmers with a body combined with a cutting system.

Common breakdowns

Having dealt with the design, it becomes clear that the search for the causes of the breakdown should be started closer to the power plug, that is, from the body of the garden tool.

• The start system is usually represented by a standard start button. It can become clogged or break the wire inside the handle of the electric scythe. To fix this, it needs to be detached from the case and then disassembled. First of all, a visual check of the integrity of the system is required. Next, you need a multimeter to “ring” the circuit. If it’s a button, it needs to be cleaned or replaced.
• The enclosed motor is usually of a standard design. If everything is in order with the starting system, then you need to check the electric motor further. First, make sure that everything is in order with the brushes. Excessive wear or distortion can lead to interruptions in operation. If everything is in order with them and the collector, then you should pay attention to the motor winding. Here again, a multimeter will help you. It is necessary to check both circuits: rotor and stator. Also, the cause of the malfunction may be in the automatic thermal relay, which opens the circuit when the engine overheats. Repairing an electric motor is a complex procedure that is best entrusted to professionals in this matter.
• Flexible shaft inside the boom. It can fray or break if not properly cared for. During operation, the shaft is in a state of rapid rotation, therefore it needs periodic lubrication. If it breaks, then it can be replaced very easily by disconnecting the rod and removing the flexible shaft from it. It should be noted that the BOTTOM grass trimmers do not have a flex shaft in the boom. But they also have a weak point. this is the bearing of the main shaft, on which the cutting system is mounted.

You must always remember that any tool needs care and careful storage. Then you can use it for longer without much repair costs.

Barberry

To cleanse the liver, you need the root of the plant. Previously, it, extracted from the ground shortly before use, should be washed, cleaned and grinded with a grater or grinder. Once the chips are dry, they can be used to make a liver cleanser. To do this, 1 spoon (teaspoon) of raw materials must be combined with 200 ml of boiling water, insist for about half an hour and drink a day, divided into 3 doses.

Parsley

The liver cleanse drink is made from parsley root. It should be brewed in a crushed form overnight in a thermos at the rate of one spoonful of raw materials. 200 ml of boiling water. You need to drink a drink in a glass three times daily.

Peeling with oat grains

Can such a folk remedy actually cleanse the liver? Reviews claim that oat grains (flakes are not suitable for replacement) allow you to get rid of toxins from any “corner” of the body. How to prepare the product? Pour a glass of grains into a saucepan, add chopped (fresh or dried) leaves of lingonberry and birch to them. each 3 tablespoons (st.). All components must be combined with 4 liters of water and sent for infusion in a cool place for a day.

Ovesol tablets

When the question arises about how to cleanse the liver, drugs from the pharmacy. this is the first thing that comes to mind. At the same time, not everyone knows that drugs are not only chemical, but also of natural origin. The latter includes “Ovesol”. It contains a complex of herbal extracts. These include sowing oats, mint leaves, peppermint leaves, immortelle flowers, turmeric root and young grass. These tablets remove toxins from the liver, thereby helping to restore the draining function in the biliary tract

Cleansing with vegetable oil

Tablets “Legalon

This preparation is based on milk thistle extract. As a result of its use, digestion and metabolism in cells are improved, and hepatocyte membranes are stabilized. It is recommended to use tablets in case of any liver ailment. The healing effect is rapid. As a result of the breakdown of lactic acid by the liver, the stamina of the body as a whole increases.

Essentiale tablets

This drug is complex. Before learning how to cleanse the liver with Essentiale tablets, familiarize yourself with their composition. The drug contains nicotinamide, B vitamins, pantothenic acid, and phospholipids, which improve the condition of cell membranes. Tablets are used for the treatment of cirrhosis, liver necrosis, acute hepatitis, in the case of an extremely high content of toxins. As a result, not only the outflow of bile improves, but also the level of cholesterol decreases, which has a beneficial effect on the work of the cardiovascular system.

How to cleanse the liver? Drugs

A lot of medicines are used to cleanse the liver. The main thing when choosing them. not be guided by personal assumptions, but follow exclusively the doctor’s prescription. Below is a description of some of the drugs.

How to properly operate an electric grass trimmer

When choosing equipment for a summer cottage, it is not always worth chasing powerful and dimensional devices. The power of the tool is undoubtedly an important parameter, but it obviously carries with it the increased weight of the device, its large size, as well as the high price and increased fuel costs. But that’s not the point.

If you have a small garden with densely planted fruit trees or a small lawn with flower beds and shrubs. then clearing it of weeds and carefully mowing the grass is clearly an overwhelming task for any lawn mower. In such cases, even a hand tool. an ordinary scythe will not help: you simply cannot swing it, bumping into tree trunks.

The ideal solution in this case is a good and inexpensive electric trimmer. It is so lightweight, comfortable and easy to operate that it always becomes a favorite of women and the elderly. A lightweight, quietly whirring electric motor, a handle with comfortable grips and a nylon line tucked into a spool. these are the main components of an electric trimmer.

How to use the trimmer correctly

The household trimmer is the easiest to use and at the same time very effective tool. It seems that there is nowhere easier. to plug the tool into an outlet and work. But still, there are some nuances that you need to know in order for the trimmer to work for a long time and efficiently.

Site preparation. It is necessary to carefully inspect the mowing area and remove all foreign objects. stones, glass, wire, etc. Having flown out suddenly from under the fishing line during operation, such an object is capable of causing injury.

Installation of the cutting system. There are low-power trimmers that can only work with a line, cutting soft and succulent grass. they do not need to install a cutting system. But some trimmer models with a motor of 1 kW or more can work with a knife. If there are tough weeds or even a small overgrowth of bushes on the site, you need to unscrew the working attachment nut and install the cutting knife. Then tighten the nut tightly with a wrench.

Before starting work. It is very important to wear protective goggles when working with the trimmer, because even if you have removed the area from debris, plant stems and grass can fly into your eyes. The same stems, grass and branches can injure hands, so it is advisable to wear gloves. We simply plug in the electric trimmer, but the battery trimmer needs to be charged for several hours before use. Then, if there is a shoulder attachment, we hang it on the shoulder, the knapsack attachment on both shoulders. We conveniently grasp the trimmer by the handles: grasp the D-shaped handle tightly with your palm, and grip the garden trimmer with a bicycle handle (U-shaped) firmly with both hands. The trimmer should be held over the grass so that the line spool or knife is parallel to the ground. Turn on start.

How to mow correctly. The rotation of the cutting mechanism is counterclockwise. Thus, in order for the cut grass to fall onto the already mown area, easily, with simple movements, we carry the trimmer in front of us, from right to left. To remove the remnants of grass, you should make a movement in the other direction. from left to right. If the area is flat and large, break it into imaginary squares and mow, moving along the outside of such a square. If the plot is on a slope, then you need to start mowing from the bottom of the lawn, passing across the plot. in one direction. Having reached the edge, you need to go back and mow in the same direction, parallel. If there are many trees in the area, only cut with fishing line, otherwise you can cut the tree trunk with a knife. In such a garden, it is best to mow around the perimeter, bypassing the tree in a circle.

Completion of work. Turn off the engine and remove the shoulder straps. it is not yet complete completion. It is necessary to carefully clean the spool and knife from the remnants of grass. Then fold the trimmer, if it is telescopic or collapsible, and hide it until the next mow.

Electric trimmer efficiency

Electrokosa, which operates from a household electrical network, is relevant on a plot with an area of ​​four to six acres, planted with trees, flowers, shrubs. It is convenient for her to carefully mow the grass near the house or along the curb, mow paths, and an environmentally friendly motor that does not produce exhaust, gas and fumes will even make it possible to remove weeds in any covered room. greenhouse or greenhouse.

The trimmer cable limits the cutting radius, but can be extended with a standard extension. If this length is not enough for you, or the parameters of the electrical network do not contribute to the normal operation of the electric motor, then you can purchase a type of electric tool. a cordless trimmer. It works autonomously, the built-in battery lasts for half an hour or an hour of intensive work. quite enough to mow the trees in the garden. The trimmer motor can be positioned at the top of the tool or at the bottom. Upper motor trimmers work well on bumpy and uneven terrain. They are also perfectly balanced and can handle tall and wet grass. no short circuits. The convenience of working with it is also increased by a single-shoulder loop, which is hung on the shoulder. The lower motor trimmer should only be used on dry grass and on level areas. Often it is the lower motor trimmers that run on a rechargeable battery.

The line also has its secrets

The line is wound on a spool inside the spool, with the ends exposed outward. When mowing, the spool rotates, and the line, with this rotation, cuts the grass. To release the ends, you need to lightly hit the coil on the ground (semi-automatic system), there are automatic reels, in which the fishing line is released itself. There are also a few rules when working with fishing line:

In order not to damage the line and reel. Try not to touch the spool and line with various hard materials. tracks, curbs, fences. This will shorten the line prematurely, damage the reel or even jam the engine. The line spool should also not touch the ground.

Cut with the ends is more effective. Cutting the full length of the line can overload the engine. It also reduces the mowing efficiency. The tool should be held so that it only mows with the ends of the line. To do this, tilt it forward. towards the mowing side.

Tall grass requires several mows. If the grass is taller than 20 centimeters, then one mowing will not do here. You need to mow two or three times, from top to bottom. This is to prevent the grass from wrapping around the reel. The wrapped grass is the ensured overheating of the engine. If the grass is still wound, you need to stop the tool and clean it.

What does the line consumption depend on? It must be remembered that the line wears out faster if the grass is tough. Therefore, it is necessary to release it more often when mowing weeds and dry tough grass. Around the foundation of the house, near the wall and curb, the line consumption will also be higher than directly on the lawn or near the trees. It is worth considering: if you work carefully and accurately, then the consumption of the trimmer line will be optimal and economical.

How to care and maintain the grass trimmer

Hand-held mowers can tackle any kind of vegetation without overstraining the user, but a careless attitude can quickly destroy any tool, including the highest quality. Proper care of the trimmer will extend its life and save money for the owner, who does not need to pay for maintenance and repair of the device. Even people with minimal technical knowledge can do such simple actions. How to care for this garden tool. in all details in the material below.

Types and features of grass trimmers

Lawn mowers are divided into two main groups: gasoline and electric. The first type runs on liquid fuel (pure gasoline or its mixture with lubricant), the second. on electricity, from the network or battery.

General recommendations

This advice should be followed by users of any lawnmower, petrol or electric.

• Store the device in a dry place.
• It is better to hang it on the wall, on a special mount.
• After each use, the device must be cleaned of dirt and mowed grass, inspected for damage and wiped off the surfaces with a soft cloth.
• Before work, you need to check whether the bolts fastening the parts of the unit are well tightened, especially the fasteners of the working head.
• It is better to wash the grass juice from the reel immediately after mowing.
• It is necessary to monitor the amount of fishing line and the condition of the metal or plastic attachments. The line must be of the correct diameter (for the bobbin being used and the type of thicket). The blades of discs and knives must be sharpened, and the reversible attachments must be turned over for uniform grinding of the teeth.

On a note! Grass is often wrapped around the reel, rod and gearbox. this slows down the rotation of the spindle and puts unnecessary stress on the motor. Long stems and leaves should be removed from the trimmer immediately after mowing or during breaks.

The turns of the cord on the bobbin must be uniform, without overlaps. The line must be wound in the right direction and in the recommended amount. There are marks on the spool: arrows to indicate direction and marks to indicate a border.

Large shrubs, trees, fences and other solid obstacles should be cut around the perimeter, with the trimmer turned with the cover towards the obstacle. Otherwise, the line consumption will increase, and the blades will become dull very quickly.

Manual mowers of the gasoline group

The principle of operation of lawn mowers. before starting work, fuel is poured into its fuel tank, which enters the engine in small portions, where it burns, and the resulting hot gas pushes the pistons in the cylinders. As a result, the crankshaft of the motor rotates, this movement is transmitted to the spindle of the working head, where there is a spool with a fishing line or a disc attachment (a knife with two or more blades).

Externally, the lawn mower looks like this. the engine and the cutting part are located at opposite ends of a long bar and are connected using a rigid or flexible shaft. Above the mount for the coil / nozzle there is a gearbox, the task of which is to transfer to the spindle less revolutions per unit of time than the crankshaft of the motor does. Buttons and control levers are located on the handle connected to the motor by a flexible cable.

Control features. a starter is used to start in lawn mowers, a gas trigger is used to adjust the speed, which opens or closes the carburetor flap, which causes more or less fuel to enter the engine. You can stop work by pressing the “Stop” button, which opens the circuit.

On a note! Most often, the trimmer head, on which the line, knives or discs are located, is attached to the bar with a screw. On the side, from the side of the mower, the cutting element is protected by a protective cover.

Preparation for wintering

In order for the gas trimmer not to lose performance during the period of inactivity, you need:

• inspect the device for cracks, chips, bent parts;
• detach the cover and cutter head;
• drain the fuel from the tank and turn on the device to use up the remaining gasoline;
• thoroughly wipe / rinse the rod, handle, casing;
• remove the coil or knife;
• clean the gearbox and add oil to it;
• inspect and wash filters.

Then remove the spark plug, pour a little (20 ml) of engine oil into the hole and gently crank the engine shaft several times with the starter to distribute the lubricant to the cylinders. After these manipulations, you need to insert the candle back, but do not twist it all the way. This procedure (except for adding oil) must be carried out once a month while the device is not being used.

Important! The engine will not corrode if the trimmer is stored in a dry place where the air temperature remains constant and does not drop below freezing. If this is not possible, the motor should be wrapped in a cloth.

If the rod is disassembled, the joints must be lubricated (for example, with lithium) to protect the metal from rust.

Running lawn mowers

The new trimmer is run in to make sure it is working properly. The motor of the device must run in to fuel and oil, the parts must rub against each other, and the fasteners must pass a strength test. This process is carried out as follows. it is necessary to start the tool and gradually increase the speed, warming up the engine, but at first it must be protected from overheating. Then you should open the throttle valve no more than 2/3 of the possible stroke, and let the engine idle for the first few minutes, and then test it on soft grass. It is best to mow the lawn.

Attention! After the test run, the oil must be drained.

How to care for trimmers

Each type of device has its own characteristics that must be considered during operation and storage. But some rules apply in all cases.