How to connect a drill without a button

connect, drill, button

How to connect a drill without a button

TEHNODOKA.RU
Technical documentation
the site was created to assist in finding documentation on various household and industrial devices
the main workshop guest contacts
Power tools, drills, grinders, hammer drills, etc.
characteristics “”

»» »New version of the site.

Replacing a button in an electric drill

Quite often, the electric drill stops working due to a breakdown of its button (it does not turn on, the number of revolutions is not regulated), we disassemble the drill, we try to do something, and when we understand that the button turns out to be a lot of wires from it, and which one was unknown where?
You buy a new button, and how do you connect it? To do this, you need a diagram of its connection:

Connecting a button where the capacitor has three terminals

Reverse button connection

In order for the engine to start working in the opposite direction, you need to reverse the connection of the wires to the brushes (in the button with a reverse, this is done using the switch lever).

I want to draw your attention when buying a button, it must correspond not only to the size, but also to the power of your drill. Let’s calculate: we have a drill with a power of 650W, P = UI, I = 650/220 = 2.95A, it turns out we need a button on U =

220V, I = not less than 2.95A, then the BUE-3 button is suitable for us

ADVERTISING:
# BigBoss.video. porn portal!

# By visiting advertisements. Thank you to the creators of the site 🙂

How to replace brushes: work in a couple of minutes

But the drill may not work due to trivial malfunctions. for example, because of the brushes inside the motor. This means that you cannot do without repairing brushes, while this work is quite simple. you do not even need to have special knowledge and tools. To do this, we disassemble the device, remove the brush holders from it and change the parts that are broken. By the way, there are models, the body of which can not be disassembled. in them you just need to remove special plugs through the installation window, after which we change the brushes.

As you can see, there are various breakdowns, many of which will be subject to you, others will be feasible only for specialists in service centers. And in order to reduce the risk of such breakdowns, you need to take care of your tool, clean it after work, check the condition of parts and brushes in order to replace them with new ones in time. However, if you see that you cannot handle it yourself, take the device to the workshop.

Drill button connection diagram. we fix the tool ourselves!

How to connect drill directly without video button

There are several reasons for drill armature or stator breakage. First of all, this is the illiterate operation of the device. For example, many users simply overload the tool, carrying out work without interruption. This leads to the fact that the drill motor does not have time to “rest”. The second reason lies in the poor winding wire, which is often found in cheap models. That is why breakdowns of cheap tools are much more common. In this case, repairs must be carried out using a specialized tool. And it will be better if you entrust this work to professional specialists.

However, if it was decided to carry out the repair on its own, you will certainly have a question. how to do everything right? As you already understood, an electric drill “suffers” from breakdowns of the armature and stator, and this can be checked by several signs, for example, when the tool suddenly sparks during operation. If there are no “bright” signs, you can use an ohmmeter.

The stator is changed like this:

  • First, carefully disassemble the device case;
  • We remove the wires and all internal parts;
  • After finding out the reasons for the breakdown, we change the spare part to a new one, close the case again.

Possible tool malfunctions. we carry out repairs ourselves

If your tool has begun to work worse, or has completely ceased to perform its direct duties, it’s time to diagnose malfunctions and try to cope with them. First, we check the wire for damage and voltage in the outlet, for which you can turn on any other device. a TV or a kettle.

If you are inspecting battery-powered devices, you need to check them when using the tester. in this case, the voltage indicated on the case should have the same value as the battery voltage.

If the voltage is less, you will have to replace the batteries with new ones. If the battery is working properly, the power supply is normal, look for problems in the hardware. The most frequent breakdowns are considered:

Shop progress update and New Machine!

  • Problems with engine operation;
  • Wear of brushes;
  • Problems with button operation.

Knowing how the electric drill button is connected, you can quickly solve the problem. In addition, a problem with the operation of the drill may also arise due to the dustiness of the tool, because the drill “takes” wood, brick, and other materials. This means that you should take care to clean the device after each use. this is the only way to reduce the risk of malfunction due to dirty tools. That is why after you have carried out repairs in the apartment, immediately clean the drill.

Connecting the drill start button

Drill button connection diagram. how to fix the problem?

Unfortunately, a tester will not be enough for you to check the performance of the instrument, which is due to the fact that most of the buttons of the device are equipped with a smooth speed control, and therefore a conventional tester may give you incorrect data. In this case, you will need a special wiring diagram for the drill button. Often in tools, one wire is connected to a terminal, and therefore pressing the button at the same time leads to ringing of the terminals. In the event that the light comes on, everything is fine with the button, but if you notice a malfunction, it’s time to replace the button.

When replacing, keep in mind that the circuit can be either simple or with a reverse. Due to this, all work on replacing the button must be carried out exclusively according to the scheme, without adding anything “from oneself”. So, the part must be suitable in size and correspond to the power of the tool. At the same time, calculating power is a fairly simple task. We use the formula P = UI (taking into account that the power of the drill is 650 W), I = 2.94 A (650/220), which means that the button should be at 2.95 A.

Switch for grinder

Here, another trouble. Some manufacturers, for example, Difmash on their UShM-020 product, made the switch so tight and inconvenient when turned on that it turns into a real problem, which can only be solved by replacing the switch with something similar, more convenient, but I I think it won’t be a problem.

Drill button connection diagram. we fix the tool ourselves!

You can also repair a drill with your own staff, the main thing is to know the prerequisites for breakdowns and how to heal them. Now we will have a conversation that how the drill button connection diagram looks like, we will not ignore other malfunctions, so you will become the happy owner of a working tool.

Wiring diagram for a drill button with a speed controller and reverse

An actually visual connection diagram is shown in the image below.

I will give a few clarifications.

  • In the figure, the most common type of spare part in question. Fastening of electrical wires from the mains plug is carried out to the terminals, which are bolted. The rest are stuck in self-clamping contacts. If your button is not like that, then it is better to make notes on the old copy of what is attached to where. Also, a diagram can be drawn on the body itself, according to which you can also navigate.
  • If you connected the capacitor as described above, then after connecting the wires from the plug, you will have only two contacts on the bottom of the case, where you need to plug two cables from the stator. They usually have the same position on the stator as shown. They need to be longer than the other two so they can reach their clamps. In this case, it makes no difference which wire to stick into which of the two contacts.
  • The remaining two electric wires from the stator, as well as cables from the brushes, are connected to the reverse clamps. In this case, the connection is carried out diagonally: the wires from the stator are stuck on opposite sides into the diagonally located contacts; and from brushes as well. In this case, from where exactly the wires will be stuck, only depends on which direction the cartridge will rotate at a certain position of the reverse trigger. The main thing is to connect diagonally.

This is the connection diagram. I hope you will be able to connect everything correctly and the drill will work as it should.

How to connect a power tool? Such a question very often arises when repairing a power tool when there is no electrical circuit, the device is partially or completely disassembled, disassembled and, in addition, has been subjected to repeated, inept repairs.

connect, drill, button

The wires stick out in different directions, some of them are interconnected, the ends of others are bare. It would seem that in this chaos, in which there is no logic, it is impossible to understand.

In fact, any electric motor can be connected correctly and without problems, even without knowing the circuit. You just need to know its type, design features and at least the basics of the theory.

I will show this using the example of connecting the Macita3612C router.

It seems that in this chaos of wires without a circuit it is impossible to understand, but believe me, this is not so. over, some wires can be dispensed with, and some are simply unnecessary.

Sometimes, when repairing or restoring the working capacity of a power tool, it becomes necessary to connect the device to the network while maintaining all the functionality that the power tool originally possessed, but only wires stick out from the body, and quite a lot (in my case, 6), and the electrical circuit cannot be found anywhere. What to do? In fact, everything is not so scary and difficult.

A distinctive feature of the collector motor collector assembly.

It is not at all necessary to know what and how was done initially. In order to connect the electric motor of the tool, you need to do the following:

Putting strap buttons on a ukulele without electric drill.

  • Find the supply chain.
  • Connect capacitors if necessary.
  • Connect switching device.

Drill button connection diagram. how to fix the problem?

Unfortunately, in order to check the performance of the tool, a tester will not be enough for you, which is due to the fact that the bulk of the device buttons are equipped with smooth speed control, if an ordinary tester gives you incorrect data. In this case, you need a special connection diagram for the drill button. Often in tools, one wire is connected to the terminal, if the simultaneous pressing of the button leads to the ringing of the terminals. When, if the light comes on, the button has a good period, but if you notice a malfunction, it’s time to replace the button.

How to connect a drill button without the help of others?

Despite the fact that the given process is rather complicated, you can carry out all the work in artisanal conditions, observing certain fundamental rules. For example, remember that opening the case results in what remains to be done for our client, and parts that are not properly fixed will simply fall out of the case. Than, this should be avoided, because later it will not be possible to assemble the device together. For this purpose, there is an option to smoothly lift the lid, noting the clear placement of spare parts on paper.

Drill Button Connection

See continuation. what is not shown in this case Connection.

Possible tool malfunctions. we carry out repairs ourselves

If your tool began to work worse, as it is also called, did not begin to do its direct duties at all, it is time to diagnose malfunctions and try to cope with it. First, we check the wire for damage and voltage in the outlet, for what purpose, of course, include at least some other device. a TV set or a kettle.

connect, drill, button

If you are inspecting battery-powered devices, they must be checked using a tester. in this case, the voltage indicated on the case must have the same value as the battery voltage.

If the voltage is less, you will have to replace the batteries with new ones. If the battery is working properly, the power supply is normal, look for tasks in the hardware. The most frequent breakdowns are considered:

  • Difficulty with motor service;
  • Wear of brushes;
  • Obstacles with button service.

Knowing how the electric drill button is connected, you can quickly solve the malfunction. Already today, a discrepancy with the service of the drill may appear due to the dustiness of the tool, because the drill takes wood, brick, and other materials. And this means, for you, take care that to clean the device after each use. only in this way, of course, to reduce the risk of malfunctions due to contamination of the instrument. Specifically, therefore, if you have carried out repairs in the apartment, immediately clean the drill.

Start button for hammer drill, drill, grinder

There are many such buttons from simple and cheap BUE, FA (price 150. 350 rubles), to expensive, but no less simple Macita HR-1830/1640.

Actually, it doesn’t matter which button will be installed. If only it fits in size and corresponds to its amperage, and how to connect a button, including with a reverse, read here.

There are several reasons for the breakdown of the armature, as it is also called the stator of the drill. First of all, this is the unlearned operation of the device. For example, some users simply overload the tool, carrying out work without interruption. This leads to the fact that the drill engine does not have time to rest. The second reason lies in the bad winding wire, which are often found in cheap models. That is why breakdowns of cheap tools are much more common. Repair and then it is necessary to carry out with the use of special tools. And it will be better if you entrust this work to professional specialists.

But if it was decided to carry out repairs by your state, you will certainly have a question. how to do everything right? Now you know, an electronic drill suffers from breakdowns of the armature and stator, and there is an option to check this with several signs, for example, when the tool suddenly sparks during operation. In that case, there are no brightest signs, you can use an ohmmeter.

The stator is changed like this:

  • At first, carefully disassemble the device case;
  • We remove the wires and all internal parts;
  • After clarifying the circumstances of the breakdown, we change the spare part to the newest one, close the case again.

How to detach an old button?

To detach it, you need a thin slotted (straight) screwdriver and a pin. Use a screwdriver to unscrew the existing bolts that clamp the cables coming from the power plug.

The rest of the wires are secured with a spring clip. To disconnect them, you need to thread the tip of the pin into the groove where the terminal is located. Thanks to this action, the terminal is released and the wire is removed along with the pin.

Drill Button Connection

Many users of electric drills may sooner or later begin to wonder how the drill button is connected to the tool wiring. This question usually appears when a malfunction occurs in the old button, which is why you need to connect a new one. In this article I will tell you how to connect it. what goes where.

I will not describe here how to disassemble the case of an electric drill to get to the insides, since I assume that since you are wondering about a replacement, then disassembling the case will not be difficult for you. I think that someone who does not know how to disassemble the case will not even think about replacing anything in the instrument on his own.

So, first you need to purchase a new button. It should match the old one in terms of size and power characteristics, so when you go shopping, take it with you for a sample and write down the exact model of your instrument.

Wiring diagram for a drill button with a speed controller and reverse

An actually visual connection diagram is shown in the image below.

I will give a few clarifications.

Drill Machine Switch Connection Diagram | Drill Machine Reverse Switch | Drill Machine Switch Repair

  • In the figure, the most common type of spare part in question. Fastening of electrical wires from the mains plug is carried out to the terminals, which are bolted. The rest are stuck in self-clamping contacts. If your button is not like that, then it is better to make notes on the old copy of what is attached to where. Also, a diagram can be drawn on the body itself, according to which you can also navigate.
  • If you connected the capacitor as described above, then after connecting the wires from the plug, you will have only two contacts on the bottom of the case, where you need to plug two cables from the stator. They usually have the same position on the stator as shown. They need to be longer than the other two so they can reach their clamps. In this case, it makes no difference which wire to stick into which of the two contacts.
  • The remaining two electric wires from the stator, as well as cables from the brushes, are connected to the reverse clamps. In this case, the connection is carried out diagonally: the wires from the stator are stuck on opposite sides into the diagonally located contacts; and from brushes as well. In this case, from where exactly the wires will be stuck, only depends on which direction the cartridge will rotate at a certain position of the reverse trigger. The main thing is to connect diagonally.

This is the connection diagram. I hope you will be able to connect everything correctly and the drill will work as it should.

Connect the drill directly without a button: it’s real?

You can repair a power tool such as a drill on your own at home, without resorting to outside help and without spending money on it. Often during operation, the drill starts to work worse, stops starting. The main reason for the breakdown of an electric drill is wear of the brushes, failure of the engine and start button. In this case, as a rule, the switch breaks often? due to which the further use of the power tool becomes impossible. To solve this problem, the old, out-of-order button is changed or the electric drill is connected directly to the power supply.

How to connect?

Connecting a drill directly to the mains without a switch is not such a difficult task, which it might seem at first glance. Before you start connecting the electric drill and dismantling the power button, you need to stock up on the appropriate tool:

  • screwdriver;
  • soldering iron;
  • insulating tape;
  • sharp knife or blade (for wire stripping).

Before connecting the drill motor directly, the power button of the device is dismantled. To do this, use a screwdriver to unscrew the screws located on the side of the electric drill. Then, after the screws have been removed, you need to dismantle (remove) one part of the power tool body. Then, when access to the switch is open, it is also necessary to dismantle it.

The wires that have been connected to the switch are connected directly to each other. This entire procedure usually takes no more than 15 minutes. The wires are strongly recommended to be soldered together using a soldering iron, and then the soldering points must be properly insulated using electrical tape. As an alternative to soldering, you can use a terminal block (pads), thanks to which the wires are connected together. You can also use cambric to isolate the connection point.

The excitation winding consists of four wires. The two diagonal wires from the coils must be connected to the wires that are connected to the brushes. The connection points must be insulated. Then the other two wires must be connected to the power cable from which the power tool is operated. If the chuck of the electric drill, after turning on the device in the power grid, starts to rotate in the wrong direction (reverse mode), then the connection wires just need to be swapped. That is, the wires that go directly to the brushes need to be connected to the mains, and those contacts that were previously connected to the network must be connected to the brushes.

Is it possible to connect a drill without a button

The drill is one of the most used power tools in everyday life. Often, during its operation, such an element as the power button fails. This is due to the fact that the switch responsible for turning the device on and off is subjected to mechanical stress, as a result of which it quickly wears out. It is for this reason that most people who use an electric drill have a completely natural question: is it possible to connect the drill directly without the power button and how to do it?

As a rule, in most cases, a similar question arises in people when the on / off switch of the electric drill fails, and it is not possible to purchase a new one. It should be noted right away that it is quite possible to connect the power to the electric drill and start it without a button. However, during such a connection, you must follow all the rules and instructions for connecting the contacts of the electric motor of the device to the wires through which power is supplied from the electrical network.

Pros and cons of buttonless operation

When using an electric drill without a power button, there are much more minuses than pluses. The only advantage of such a power tool connection diagram is that there is no need to change or repair the switch. However, in the case of direct connection of the drill to the mains, many problems arise. For example, the functionality of the device suffers.

Without a switch, it is impossible to adjust the speed or turn on the reverse mode. In addition, with such a connection, the soft start function, which is equipped with most modern models of high power electric drills, will not be available. Also, before each use of the drill, you must constantly plug the power cord into the outlet, and turn it off after completion of work, which is not very convenient.

When connected directly, without the possibility of self-adjusting the speed, the engine of the device will immediately start working at full power. In addition, the contact groups of the switch, when the power tool was turned on, took on part of the load. In its absence, both the winding of the electric motor and the brush will be subjected to increased load. As a result, the motor of the power tool will wear out and quickly fail.

Checking the electric motor: causes of breakdowns and repairs

There are several reasons for drill armature or stator breakage. First of all, this is the illiterate operation of the device. For example, many users simply overload the tool, carrying out work without interruption. This leads to the fact that the drill motor does not have time to “rest”. The second reason lies in the poor winding wire, which is often found in cheap models. That is why breakdowns of cheap tools are much more common. In this case, repairs must be carried out using a specialized tool. And it will be better if you entrust this work to professional specialists.

However, if it was decided to carry out the repair on its own, you will certainly have a question. how to do everything right? As you already understood, an electric drill “suffers” from breakdowns of the armature and stator, and this can be checked by several signs, for example, when the tool suddenly sparks during operation. If there are no “bright” signs, you can use an ohmmeter.

The stator is changed like this:

  • First, carefully disassemble the device case;
  • We remove the wires and all internal parts;
  • After finding out the reasons for the breakdown, we change the spare part to a new one, close the case again.

Required tools and materials

Drill repair can be carried out on your own, the main thing is to know the causes of breakdowns and methods of their “treatment”. Today we will talk about how the drill button connection diagram looks like, we will not ignore other malfunctions, thanks to which you will be the happy owner of a working tool.

How to connect the drill button yourself?

Despite the fact that this process is quite complicated, you can do all the work yourself, observing some important rules. For example, remember that opening the case can cause all parts and loose parts to simply fall out of the case. Naturally, this should be avoided, because then it will be quite difficult to put the device together. To do this, you can smoothly lift the lid, noting the exact location of the spare parts on paper.

The button is repaired as follows:

  • First, the clamps for the casing are hooked, after which it is carefully pulled together;
  • All rusted and darkened terminals are cleaned of carbon deposits, for which you can use alcohol or sandpaper;
  • We reassemble the tool, making sure that all the parts of the device are in place, and we check the performance of the drill. if nothing has changed, we change the part;
  • We fill the turnover regulator with a compound, and therefore, if the part fails, we simply replace it;
  • A frequent breakdown is the erasure of the working layer under the rheostat. it is better not to repair it, just waste your time, it is better to buy a new one and replace it.

Many are interested in where to get such a scheme? First of all, it should come with the tool when you buy it, but if there is no scheme, or you have lost it, you will have to search the Internet. After all, only with its help you will be able to carry out the repair correctly, without errors. By the way, the speed control button and the reverse control button are located in different places, and therefore they will have to be checked separately.

Drill button connection diagram. how to fix the problem?

Unfortunately, a tester will not be enough for you to check the performance of the instrument, which is due to the fact that most of the buttons of the device are equipped with a smooth speed control, and therefore a conventional tester may give you incorrect data. In this case, you will need a special wiring diagram for the drill button. Often in tools, one wire is connected to a terminal, and therefore pressing the button at the same time leads to ringing of the terminals. In the event that the light comes on, everything is fine with the button, but if you notice a malfunction, it’s time to replace the button.

When replacing, keep in mind that the circuit can be either simple or with a reverse. Due to this, all work on replacing the button must be carried out exclusively according to the scheme, without adding anything “from oneself”. So, the part must be suitable in size and correspond to the power of the tool. At the same time, calculating power is a fairly simple task. We use the formula P = UI (taking into account that the power of the drill is 650 W), I = 2.94 A (650/220), which means that the button should be at 2.95 A.

Possible tool malfunctions. we carry out repairs ourselves

If your tool has begun to work worse, or has completely ceased to perform its direct duties, it’s time to diagnose malfunctions and try to cope with them. First, we check the wire for damage and voltage in the outlet, for which you can turn on any other device. a TV or a kettle.

If you are inspecting battery-powered devices, you need to check them when using the tester. in this case, the voltage indicated on the case should have the same value as the battery voltage.

If the voltage is less, you will have to replace the batteries with new ones. If the battery is working properly, the power supply is normal, look for problems in the hardware. The most frequent breakdowns are considered:

  • Problems with engine operation;
  • Wear of brushes;
  • Problems with button operation.

Knowing how the electric drill button is connected, you can quickly solve the problem. In addition, a problem with the operation of the drill may also arise due to the dustiness of the tool, because the drill “takes” wood, brick, and other materials. This means that you should take care to clean the device after each use. this is the only way to reduce the risk of malfunction due to dirty tools. That is why after you have carried out repairs in the apartment, immediately clean the drill.

Drill button connection diagram. we fix the tool ourselves!

How to replace brushes: work in a couple of minutes

But the drill may not work due to trivial malfunctions. for example, because of the brushes inside the motor. This means that you cannot do without repairing brushes, while this work is quite simple. you do not even need to have special knowledge and tools. To do this, we disassemble the device, remove the brush holders from it and change the parts that are broken. By the way, there are models, the body of which can not be disassembled. in them you just need to remove special plugs through the installation window, after which we change the brushes.

As you can see, there are various breakdowns, many of which will be subject to you, others will be feasible only for specialists in service centers. And in order to reduce the risk of such breakdowns, you need to take care of your tool, clean it after work, check the condition of parts and brushes in order to replace them with new ones in time. However, if you see that you cannot handle it yourself, take the device to the workshop.