How to cut a baguette on the ceiling corners
Cutting Techniques. Straight Corners over Texture
How to glue baguettes to the ceiling: step-by-step installation instructions
The finishing of the ceiling surface is almost always completed with the installation of a decorative skirting board, which gives the room a complete and harmonious look. However, this part of the work requires adherence to a certain sequence and technology, especially in terms of the design of the corners. In the article, we will look at how to glue baguettes on ceilings so that the repair is of high quality.
How baguettes are glued to the corners
To glue the baguettes in the corners of the room, proceed in the following sequence:
- cutting off the end of the products, attach the fillets to each other, check the place of their joining for gaps;
- trim off interfering areas with a knife;
- coat the skirting boards with glue, attach them to the wall surface. If the adhesive requires curing, wait for the specified amount of time.
How to glue a baguette to the ceiling
Before you start gluing the ceiling molding, you need to decide what will be the installation of the products. Most often, formulations are used for expanded polystyrene materials. But there are other alternatives on sale:
- putty is often used to glue two surfaces together. The main advantage is that it not only reliably fixes the skirting board, but also allows you to immediately fill in visible seams and transitions;
- liquid nails qualitatively fix the plinth under the ceiling, providing instant adhesion of two surfaces;
- acrylic glue is used for mounting wooden skirting boards and foam moldings;
- silicone sealants are also used for fastening baguettes, but they have a significant drawback. after installation, the exposed areas of silicone cannot be painted.
To make sure that you have selected the correct adhesive for your skirting board, read the information on the instructions for the adhesive. Usually manufacturers indicate the type of material for which a certain type of glue is suitable.
Fastening the skirting board before wallpapering
In this case, the peculiarity of the work is that first, the baguettes are glued to the ceiling, the cracks and gaps are closed with the help of a putty mixture, and after that they proceed to finishing the wall surfaces. In this case, it is necessary to bypass the line of gluing the baguette very qualitatively. Even the slightest shortcomings of subsequent repairs that were made in this place will become noticeable. If you are not confident in your abilities, then glue the baguettes on the ceilings after the decorative wall decoration.
How to glue a baguette to the ceiling in the corners
Docking the plinth in the corners is the most difficult stage of work associated with their installation.
Important! In order not to spoil the material, adjust the last straight plank to size after gluing the corner.
If in your room all angles are strictly 90 °, the following recommendations will help you to properly cut the baguette:
- place the baguette in the miter box exactly as it will be located on the wall surface;
- press the lower part of the plinth firmly against the wall of the tool;
- with a miter box to the desired size, cut off the fillet parts that will join in the corners;
- use a construction blade to process the extreme sides of the parts to the end;
- check the evenness of the joints by applying the elements to each other at right angles so that no burrs remain. Otherwise, there will be gaps at the installation site.
How to properly glue a baguette to the ceiling
In order to correctly install the plinth, it is necessary to make markings on the wall surface. This step can be skipped if all angles in your room are strictly 90 °. For a large work space, it is best to start at the corners. Prepare a solution of water and soap in advance, a small sponge and a spatula.
The algorithm of actions will be as follows:
- Apply a small amount of glue to the edge of the plinth with a spatula, carefully coat the joints of the elements;
- work carefully so that no glue gets on the front side of the skirting board;
- attach the baguette to the surface, press it firmly;
- immediately remove the protruding glue with a sponge dipped in soapy water;
- after you have pasted over the entire perimeter of the ceiling with the baseboard, seal the seams between the individual parts with putty.
Features of using baguettes
In addition to the fact that ceiling moldings allow you to harmoniously arrange the transition from wall to ceiling surface, they also have a number of advantages, including:
Depending on the material from which the ceiling moldings are made, you can choose the following types of products:
- foam and polyurethane;
- plastic;
- aluminum;
- gypsum
- wooden.
Ceiling skirting boards can be smooth or embossed, narrow and wide.
Other pruning methods
As a rule, in ordinary rooms, the evenness of walls and ceilings is rarely observed. With slight deviations, they can be trimmed during the fitting process. If the deviation of the angle from the standard 90 degrees is large, you need to know how to cut the ceiling plinth without a miter box.
There is only one way out in such a situation. to carry out a procedure on how to cut corners on the baseboards on the ceiling in place:
How to cut ceiling moldings baseboard without a miter box if you corners not 90°
- To carry out the procedure, how to properly cut the plinth to the ceiling, you need to arm yourself with a finely sharpened pencil (with its help you can apply clear marks that are not visible from afar), a fragment of a baguette, a ruler and a good office knife (if a plastic or wooden plinth is mounted, then a saw).
- Attaching the frieze to the corner, make a pencil mark along the outer edge. Do the same with the reverse side of the corner. As a result, the line should form a cross on the ceiling. The point of intersection of the marks will be the convergence point for the edges of the ceiling frieze. To transfer the scheme of how to properly cut the ceiling plinth at the corners, a frieze is applied and rests with the end part in the corner.
- Next, using a ruler, you need to connect the edges of the frieze and the markings. A simple operation, how to cut a plinth for a ceiling on a solid surface, will not give a positive result: there will still not be a complete connection along the cut of the corner of two separate moldings. In this case, it is necessary to carry out additional trimming in place. This option is suitable for not very wide friezes (up to 5 cm).
- To trim the corner more accurately, you need to put the plinth on the end. When cutting, the knife should move obliquely at an angle of 45 degrees (so that the edge is sharp). After that, fitting in place, if necessary, will be on a very small scale.
- A similar procedure, how to properly cut the plinth on the ceiling, is carried out in relation to the second plank. It must be attached to the place of future installation, resting its butt on the adjoining side of the corner. Next, mark a point with a cross, apply a marking and cut off at the bottom. If adjustment is required, then it is carried out even before spreading with glue.
Similar actions are carried out on the outer corner. It is most convenient to first cut one corner, and adjust the second along it.
Varieties of ceiling plinths
The classification of the baguette is carried out according to the material of manufacture:
- Plaster. The most ancient representatives of ceiling plinths. For their casting, special matrices were used. Various solutions were used as an adhesive assembly. The name “fillets” is also used for plaster moldings. In modern construction, they are used very rarely due to the high cost and inconvenience of installation. In addition, more reliable and inexpensive simulations of plaster fillets have appeared.
- Polystyrene (polyurethane). The most common type of skirting board. Products of this type are characterized by low cost, excellent aesthetic characteristics, ease of installation and a rich assortment in terms of external design. The width of polystyrene moldings varies from 5 to 250 mm. They can be used in any type of room, complementing various interior styles.
- Wooden. Expensive and rather bulky baguettes, with the help of which wooden houses with the corresponding interior are mainly made out. To install wooden planks, in addition to glue, screws and nails are often used.
- Plastic. An excellent option for bathrooms and other rooms with high humidity. Installation is carried out on special moisture-resistant glue or secret self-tapping screws.
When installing the above products, you need to know how to cut the ceiling plinth. This does not apply to plastic products that come with special angle adapters.
Ways to get a beautiful angle
The most difficult area when decorating the ceiling surface with a frieze is the corner areas. If you just cut the skirting board at the right angle, ugly gaps will remain. To achieve a snug fit between two adjacent products, you must also trim their edges. There are several ways to do this.
What tool is needed
When installing the ceiling plinth, it must be cut to size or in the corners.
The following tools will usually help you to cut the corner of the skirting board:
- Hacksaw for wood. It is used for working with wooden products.
- Hacksaw for metal. This tool is convenient for cutting plastic, foam and polymer friezes. As a result, it is possible to obtain a fairly clean joint without burrs. When working with saws, it is convenient to use a miter box.
- Stationery knife. It can be used to cut styrofoam baguettes without using special tools. The main thing is that the knife is well sharpened and has a thin and even blade. If you act carefully, the cut is smooth, without any dents.
When using the saw, it is important not to use excessive force, otherwise the skirting board will be crumpled. It is best to practice on some unnecessary piece first. This will allow you to get beautiful fragments in the future.
How to cut a corner of a ceiling plinth. simple and correct ways
The aesthetic perception of the entire room directly depends on the beauty of the ceiling decoration. This is especially true of the quality of gluing the baguette: if it is not difficult to do this on straight sections of the walls, then when decorating the corner sections, you will need to know how to cut off the ceiling plinths.
How to cut a corner with a miter box
In rooms with even corners and walls, cutting the ceiling plinth using a miter box is usually not very difficult. The tool has the form of a U-shaped groove with saw guides made at an angle of 90 and 45 degrees. Having placed the element requiring cutting inside the device, insert the saw into the guides. During the cutting process, the baguette must be firmly held in place to avoid defects. Cutting off the plinth is quite difficult, since it is necessary to achieve its simultaneous adherence to two planes. If the width of the baguette is small, then it is more convenient to press it to the near side. “How to cut ceiling plinths. cutting tools and rules”.
How to cut off the corner of a ceiling plinth if you are making an outer corner:
- Before cutting the corners of the ceiling plinth with a miter box, it is washed down at an angle of 45 degrees.
- The miter box is exposed in a comfortable position. This will make it possible to determine the exact location of the skirting board: first of all, this concerns the edge of the product that will be adjacent to the ceiling. To avoid confusion, it is best to place the right-side plank on the right and the left-side plank on the left.
- The surface is pressed against the lower surface of the miter box. In this case, the second part rises, turning out to be the closest. It must be applied to the wall of the miter box in such a way that during operation it will not wobble. With this arrangement, the front side of the product turns out to be turned in the opposite direction.
- Cutting must be done at an angle of 45 degrees from yourself. If done correctly, the two halves are folded together to create a beautiful outer corner.
After the correct sawing of the ceiling plinth in the corners is completed, both pieces must first be applied to the ceiling “dry” in order to check the coincidence of the corner geometry. If necessary, trimming is carried out with a knife. It is easier to cover small gaps with a putty, which, after drying, must be treated with sanding paper. As for the inner corner, it is much easier to arrange it.
The procedure for how to cut the ceiling plinth in the corners of the interior type is very similar to the one described above. The first step is to determine the side that will be adjacent to the ceiling. It is placed at the bottom of the miter box. The reverse side leans against the near wall. After sawing off the plinth on the ceiling is finished, the resulting fragments must be applied dry to the corner, checking the quality of the joint. Fitting is carried out if necessary. After that, one and the second skirting boards are installed on the assembly structure. Small gaps in the corner can be filled with a special putty.
Using decorative corners
This refers to special corner adapters, which are usually completed with polyurethane and polystyrene friezes. Decorative corners are glued to the very corner, and the baguettes are adjacent to them on both sides. Adjustment in this case is either not required at all, or is carried out with a simple clerical knife.
Docking on straight sections
The most difficult areas when decorating the ceiling perimeter with a frieze are the corner areas. Having passed the first corner, they usually begin to move in both directions at once, gluing bar by bar in turn. If the entire frieze fits in straight docking, there are no problems: having cut both edges with a miter box at an angle of 90 degrees, they are connected with mounting glue. The main thing is to achieve maximum invisibility of the joint.
A little difficulty arises when the installation work is approaching the next corner and the frieze needs to be cut to length. This should be done with a certain margin for corner trimming. Experienced craftsmen recommend leaving a stock of at least 10-15 cm, taking into account possible mistakes during registration (sometimes it does not work the first time). After the corner of the frieze is cut and checked, the plank is applied dry to the area remaining from the corner with a straight cut towards the nearest baguette. Marking the length with a simple pencil, cut off the excess at an angle of 90 degrees, and glue the manufactured and fitted piece.
How to cut styrofoam with a soldering iron
You will need a soldering iron, screwdriver, pliers and copper wire.
Remove the working tip. Use a pair of pliers to bend the wire in half and measure on it a length equal to the length of the tip. Bend the excess ends. Leave about 1/3 of the length of the working tip, and “bite off” the rest with pliers. Insert the improvised copper “tip” with the thicker side into the soldering iron.
Secure with a screwdriver and plug in the tool. The heated copper wire literally floats on the foam in the direction you need. It is possible to pre-apply the cutting line of the cut to the material.
How to trim a baguette with miter box
The tool allows you to maintain the desired angle when cutting the skirting board. As a rule, they are designed for angles 450 and 900, sometimes 600. serious tools are equipped with a swivel mechanism for adjusting non-standard angles.
How to cut a polyurethane skirting board
Polyurethane is a fairly strong material, so a stationery knife is not suitable for cutting such a baguette. This can be done with a hacksaw or a miter saw. For the first tool, you will need a miter box for marking corners. The circular saw is equipped with a scale for adjusting the corners, so you do not need a miter box. But this tool is expensive.
The polyurethane skirting board can melt when cut. Sometimes this happens because the cutting blade is not sharp enough. Therefore, before cutting the polyurethane with a miter saw, sharpen the knife or spray it with cold water from a sprayer.
How to cut corners baguettes correctly?
Beautiful joints of skirting boards are obtained not only due to their plastering. The quality of the panel cuts also contributes to the result. Today we are talking about how to properly cut a baguette, what tool is needed for this, and what you can do without.
How to cut a PVC skirting board
When cutting plastic skirting boards, we recommend using a metal hacksaw. The thinnest and sharpest blade gives the most accurate cut. no chips or notches.
The second popular tool for cutting PVC skirting boards. stationery knife. They also usually cut foam baguettes. Well, if speed is more important than edge quality, you can arm yourself with an angle grinder.
How to trim a baguette without a miter box
Instead of a miter box, you can arm yourself with a pencil and. a ceiling! Marking in place allows you to join the skirting board in corners of any size. even straight lines or with flaws.
- Cut the planks that will be adjacent at an angle of 900;
- rest one of them with its butt against the wall and draw a fishing line along the contour of the baguette;
- rest the striker against the perpendicular wall and also outline one side of it;
- the point of intersection of the lines. control, according to which you will need to make a cut;
- again attach each of the cornices to their place and transfer the control point to them;
- draw the line from the control point to the top of the other corner of the plank, cut along it.
The skirting boards can now be joined at the desired location. We have described how to cut baguettes without a miter box in the inner corners. In a similar way, you can outline the necessary points for external.
How to cut styrofoam with string
The cold wire cutting method is simple to perform and does not require anything other than the string itself and foam. It is also suitable for cutting PPS ceiling plinth.
Stretch the steel string and perform movements similar to cutting with a two-handed saw. The foam will heat up from friction, and the string will go through it like clockwork.
How to cut styrofoam figuratively
Foam plastic begins to melt under the influence of high temperatures. This property of the material is widely used for decorative cutting of foam plastic. The thermal cutter transformer supplies electricity to the arcs, which heat the tensioned wire. Hot strings, in turn, cut the foam along the path specified by the drawing.
The professional tool allows you to apply curly nozzles, recreate complex sketch elements and achieve high cutting speeds.
How to make a miter box yourself?
If desired, the miter box can be made at home. It can be crafted from wood or iron. The dimensions of the workpiece do not play a special role, but the wider it is, the more accurate your cuts will be. However, if the width is greater than the length of the hacksaw, with which you will cut the baseboards or boards, then it will be extremely inconvenient to saw, so you do not need to take a workpiece that is too wide.
First, a transverse line is marked in the center of the workpiece. Then, marks are made at a distance of 1/2 the width of the workpiece from the intersection of the straight line with the edges of the workpiece. Then these marks are connected crosswise, as shown in the figure.
Wooden miter box, fastened with self-tapping screws
Next, the process of marking the side walls of the miter box begins. Attach them to the already marked base and make marks based on the base markings. Then draw straight lines from these marks across the entire wall.
The scheme of making a wooden miter box
After that, the process of mounting the miter box begins. The walls must be attached to the base with self-tapping screws if the fixture is made of wood or chipboard or corners with bolts if it is made of steel. Only after installation in the miter box are sawed slots for the saw.
After making the slots, the miter box is ready. If you have a large amount of work or want to repair regularly (on a professional basis), this simple device can speed up the process of cutting skirting boards by 5-10 times.
Cutting a paint edge at the ceiling near popcorn
How to cut skirting boards to the ceiling: corners
Today it is impossible to imagine the interior of a residential building or apartment without ceiling plinths. The skirting board covers the irregularities of the suspended ceiling or wallpaper, cracks and imperfections in the walls, and gives the interior completeness. But how to make the skirting board perfectly fit in the most important place. in the corner? There are several ways.
If the angle is not right
Unfortunately, in some cases, the angle between the walls in the room is not straight, but sharp, or, conversely, obtuse. This is due to structural defects that have arisen through the fault of non-professional builders, the architect’s idea or the result of soil subsidence some time after the construction of the building. This is especially common in village houses and summer cottages.
House plan with sharp and outer corners
No miter box or a drawing replacing it will help in this case, and you will have to do the markup in place.
- Attach the workpiece to one of the walls so that it rests against the other wall with its end.
- Run the line on the ceiling along the workpiece.
- Perform the same operation against another wall.
- At the intersection of the two lines, put a mark on the workpiece itself.
- Draw the line from the mark to the corner of the workpiece and cut along it.
- Do the same with the workpiece, which you will attach to another wall.
- Glue both blanks; they will come together tightly.
Outside corners
It happens that the room has not only internal, but also external corners, which also need to be pasted over with a plinth (see photo). How to do it? There are several ways here as well. The easiest way, as with the inner corners, is to cut them with a miter box. The outer joints must be cut so that the side that will be glued to the ceiling is on the surface of the miter box, and the side pressed against the wall is facing the wall of the fixture.
As with the inside corners, you can also use in-place markings, that is, draw the line on the ceiling. Here, the technology is exactly the same as that used for the inner corners.
You can use the markings on the wall by attaching a workpiece and drawing a fishing line along its lower edge (see photo).
If the outer corner turns out to be too rounded, you can finish the joint with a knife.
Trimming the ceiling plinth. Outside and inside corners
To the point where they converge, the line is drawn directly along the future part of the connection. From the point on the ceiling to the second one. The resulting marking will be the line along which you need to saw off or cut off the connecting parts. Using these techniques, you no longer need to wonder how to cut the corners of the ceiling plinth.
How to cut a skirting board without a miter box?
The easiest way is to draw the future cut line on paper (cardboard, wallpaper), and then, attaching the baseboard blank to it, cut.
To do this, you must first attach the skirting board blank to the paper and draw two parallel mowing lines that will mark the sides of the skirting board. Then, using a protractor, you will have to measure 45 degrees and draw the line of the future cut. Then the drawing is used in the same way as the miter box: a blank is placed on it and the excess is sawn off along the mowing line.
How to cut the corners of a skirting board without a miter box
The disadvantage of this method is that the saw will have to be held on weight, focusing on the drawing, and not inserted into a prepared slot.
What tools can be used?
The feasibility of using certain tools is associated with the materials from which the skirting board will be made.
Tab. 1. Varieties of materials and features of their use.
| Polyvinyl chloride (PVC) | PVC skirting boards are distinguished by the fact that they are easily damaged when pressed and no longer restore their former appearance, since they are devoid of elasticity. Therefore, such skirting boards cannot be pressed when cutting. | Cut with a construction knife or a hacksaw for metal. A blade or a sharpened kitchen knife will also work. |
| Styrofoam | Foam plinth is also not very durable, but better than PVC counterparts. Easily crumbles. | The same tools can be used as for PVC |
| Wood | Stronger and more aesthetically pleasing than their polymer counterparts, but expensive. | It is best to cut the tree with a hacksaw, you can use metal, although this way you run the risk of hammering the teeth of the blade with wood sawdust. A hacksaw with fine teeth is best. |
Using factory corners. an alternative to cutting and sawing
PVC ceiling molding corners
The disadvantage of corner pieces is that they are actually and visually larger than the baseboard, which will make the corner noticeable. This can ruin the look of the room. It is also inconvenient to use the corners where the walls do not join strictly at an angle of ninety degrees. But most of the time they look great.
How to join the corners of the skirting board
Installing a skirting board may seem like an easy task, but it is extremely difficult and requires a lot of care. In the process, beginners are faced with numerous problems, the most common among them is the docking and cutting of dumbbells.
Performing the work, we prepare the following tools for cutting and joining:
- a clerical knife or a knife for metal (depending on the material from which the plinth is made);
- goniometer;
- ruler;
- pencil;
- miter box.
It is designed for cutting dumbbells at perfectly even angles, and if they are not such or the tool is not available for some reason, the element will need to be trimmed manually. To determine whether we need it or not, it is recommended to use a protractor. If they turned out to be curves, then before installing the baguette, they must be leveled with plaster or drywall.
The hardest part of joining is cutting. The slightest mistake leads to a waste of materials. Dumbbells are attached to the ceiling differently from the usual ones, but a little differently. It should be remembered that they are cut off not only from the front side, but also along the outer edge. The simplest material to work with is foam. It is easy to cut and not so fragile compared to other materials, so it is much easier to work with it.
How to cut a baguette without a miter box
If there is no miter box in the house, then its analogue is made with one’s own hand. Alternatively, they draw on a simple album sheet. To do this, on paper, draw two mowing lines with marks of a certain degree. You can put them off using a regular school protractor. They use a miter box of their own production in the same way as a purchased one. You just need to put the product correctly and cut off the excess part.
It is also really possible to make it with your own hands from three boards, making slots there, which can be marked with a student’s square or the same protractor.
How to make the outer corner of a ceiling plinth
Inside corners are much more common than outside corners. Usually they are at least 180 degrees. Despite this, it is not at all difficult to dock them.
To correctly cut the baguette, the first thing to do is draw a mark on it, for this we attach it to the ceiling and mark with a pencil the place where the cut is planned to be.
Then we put the product in the miter box at an angle of 45 degrees. When it is already placed there, it is carefully trimmed. It should be remembered that if that part of the dumbbell, which is more located on the left side, then we cut it off according to the left designation, in the same way as the inner corner. Next, we cut off according to the same plan and the right.
When the ceiling frieze has already been cut, make sure it is done without any errors. To do this, fold the two pieces together and only if they fit perfectly can they be attached to the wall.
When cutting, the frieze should be kept straight, since with a curved trimming, gaps appear when joining and for the same reason it needs to be cut with only a sharp blade.
Simple secrets of a successful baguette installation
When cutting, you should not make much effort, since the foam will crumble, and the wood. split.
Dumbbell elements are usually tried on to the wall, and if there are no gaps, and everything fits snugly, then the work is done correctly.
After the plinth is fixed in the corners, it is recommended to fix all subsequent parts, but before that they are processed at the junction with sandpaper. It must be remembered that the docking of each should be without cracks and irregularities.
For those who do not want to do difficult work, but are also not ready to give up the decorative element of the apartment, it is possible to use a special component that closes the joint. Looks very original and saves time and effort.
For a complete picture of the process of joining a ceiling molding, watch the video with a detailed description of the steps.
How to join the corners of the ceiling plinth: photo and video instructions
The ceiling plinth mainly performs decorative functions, it allows you to hide all repair errors. It is attached after pasting the wallpaper at the junction of the walls and ceiling. A well-chosen skirting board can visually expand a room. It all depends on the chosen model and size. Now on the construction market you can find a huge variety of ceiling skirting boards. Currently, they are made from polystyrene, polystyrene, polyurethane, gypsum, polyvinyl chloride, which is the most economical option, and are also made from various types of wood. Wooden skirting boards look much more aristocratic than the others, but they are also harder to work with. In any case, the choice will mainly depend on the style of the room. Ceiling skirting boards are also called a frieze, baguette or dumbbell.
How to make an inner corner of a ceiling plinth
An internal angle is one that is not more than 180 degrees. These are the ones that most often have to be cut. Trimming the edges of the baguette is carried out, as a rule, with a miter box, but you can do without it.
If this happens with its help, then before docking it is necessary to take into account that the element that touches the side of the tool when cutting off is glued to the wall of the room, and the one that touches the lower part is attached to its ceiling.
It is recommended to measure the angle between the walls of the room, and if it turns out to be straight, then the dumbbell is cut at an angle of 45 degrees. To make an undercut, for a start, the desired element is installed in the miter box. Then the edges are cut.
If the walls turned out to be crooked, then the best option is to cut the plinth yourself, you will need a ruler and a clerical knife. To do this, attach two different parts to the wall and mark the place of the cut with a pencil, after which they carefully cut.
To control the accuracy of the work done, the product is first tried on the wall, and only if it is cut off without any errors is it fixed, and if you nevertheless noticed irregularities, then it is very easy to correct them with a clerical knife and only then mount it.
Usually, if the corners of the room are even, then no problems should arise with them, but if not, then minor flaws are always eliminated, the main thing is to try hard.
How to cut a baguette with miter box
To cut the baguette using a miter box, we fix it in the tray as it will be attached to the ceiling. Cut it off along the guide groove. If it is wooden, then we cut it with an ordinary hacksaw. There is also a hacksaw for metal, and to cut off expanded polystyrene or polystyrene, we will use a simple stationery knife, but it must be very sharp so as not to damage anything.
Sticking ceiling baguettes with your own hands: a master class with a photo
If you are faced with the issue of gluing ceiling moldings, and want to do it with your own hands, then this master class will be your first assistant.
Suppose that you have mastered the science of creating drywall structures perfectly and were even able to mount and putty a simple ceiling in your apartment. This means that determination and the desire to learn something new is the principle of life for you. All this is good, but to complete the complete picture, so that the ceiling looks harmonious with the walls adjacent to it, you also need to learn how to glue baguettes for the ceiling. What we will do with you in this article. And first, let’s figure out the question of how to properly trim the baguettes at the corner joints.
How to cut baguettes
The first thing to do before proceeding directly to gluing is to learn how to properly cut the ceiling molding. you cannot do without high-quality trimming in the corners, and in straight sections, too. What do you think a skirting board would look like when joined with a thumb-sized gap? Naturally, it’s ugly. that’s why you need to approach the issue of cutting baguettes with all responsibility.
As a rule, a device called a miter box is used for corner and straight trimming of baguettes. The thing, of course, is good, but in practice it is a weak helper. The reason for this is the uneven corners of the room. as a rule, in most apartments, the corners of the walls do not have a clear angle of 90 °. This is the whole catch, which still brings us back to manual cutting of baguettes without the use of a miter box.
How to properly cut a ceiling baguette
But nevertheless, in deciding how to glue the baguettes to the ceiling, the miter box is not a completely useless thing. it can be used by novice builders as a visual aid. Thanks to this tool, you can clearly determine in which direction and at what angle you need to cut the baguette to form internal and corner joints. On this we will stop with the theory and start training.
How to glue baguettes to the ceiling
To begin with, before proceeding with gluing the baguettes, the ceiling and the upper part of the adjoining walls must be opened with a primer. the dust remaining after it has been cleaned with an abrasive cloth must be completely removed. Please understand that no glue will stick to the dusty surface.
Ceiling primer photo
As a rule, gluing baguettes to the ceiling starts from the left inner corner of the room. After intensive training in trimming ceiling moldings, let’s start gluing a high-quality trimmed corner. For these purposes, you can use both an ordinary finishing putty and special glue. At this point, as you like, both glue holds 100%.
Sticking baguettes on the ceiling photo
We put it on the edges of the baguette with a solid line. there is no other way to glue the baguette with high quality.
How to glue a baguette to the ceiling
Well, then everything is simple. We take a baguette smeared with glue and press it tightly into the corner between the ceiling and the wall. Excess glue must be carefully removed with a spatula or, in the case of putty, we wash it off with a brush with water.
Sticking ceiling moldings in the corners
Instructions for gluing baguettes for the ceiling
Asking the question of how to glue a ceiling molding, one must not lose sight of the cracks that form at the points of its connection with the walls and ceiling. They will definitely need to be properly sealed with putty or glue. We take a putty or, as shown in the photo, a glue gun, and clog the joints of the baguette with the walls and ceiling with glue.
Glue ceiling baguettes photo
Here, it will also be necessary to remove glue residues with high quality. especially for the ceiling. Traces from it can show through from under the paint.
How to glue a ceiling baguette
The same should be done with the connection of individual parts of the baguettes. all the cracks in the corners and at the joints of straight sections must also be sealed with glue or putty. If the gap is very large (more than 2mm), then before cleaning the joint from the putty, it must be allowed to dry a little. otherwise the water will simply wash it out and everything will have to be done again.
Sticking baguettes on the ceiling photo
The next thing you need to know in order to dock the ceiling molding-molding with high quality, without drops and curvatures, is the ways of fixing it to each other. So that the seam between the individual parts of the baguette is not visible, they must be cleaved together with needles or pins. this step will prevent the baguette from changing its position as the glue dries. Subsequently, these needles are removed, and small holes are neatly hidden with putty. This method fully justifies itself when decorating the ceiling with a baguette in a room with external corners, it is with them that beginners have the greatest number of problems.
Decoration of the ceiling with a baguette
The ceiling moldings glued in this way must be left alone for at least 12 hours for the glue to dry completely. Only then can you start painting the ceiling, which is described in detail in the next article.