How to cut a branch on a tanning tree properly. Sprinkled the barrel into pieces (cutting)

Technology of sawing logs on a chainsaw boards

The chainsaw is a technically complex and dangerous tool, for this reason, working with a saw, you need to comply with certain rules. Sowerant users are often related to working with a chainsaw with less attention and violate the rules, this leads to injury to the operator or a tool breakdown.

In this article, we will consider how to properly prepare a chainsaw for work, what are the rules and methods of rolling and sawing trees, we will talk about how to cut a chainsaw, separately dwell on safety precautions.

Preparation for work

The first thing where work begins with a chainsaw is its assembly. The assembly scheme of various models is practically no different. A saw tire and circuit are installed on the saw, the chain is tending.

The chain can be considered properly stretched if it does not sag on the tire and easily scrolls through with his hands. If in order to crank the chain you have to make too much effort, then it is pulled and you should slightly loosen its tension.

Next, it is necessary to control the sharpening of the circuit, for this, the cutting edge of each working tooth is visually inspected. The edges should be even without dents and Zazubrin.

The next stage is the gas station refueling. The fuel mixture is prepared in a certain proportion, to find out which by reading the user’s guide supplied with a saw. Basically, the fuel mixture is diluted in a proportion of 1:50, that is, one liter of AI gasoline. 92 must add 20 grams of oil for two.stroke engines.

Important: When pouring fuel and oil for lubricating the chain into the tanks, you need to be extremely careful and not confuse. If you pour oil into a tank for the fuel mixture, then the chainsaw will not work. To restore performance, it will be necessary to rinse the fuel tank with gasoline, as well as clean the fuel highway and carburetor, which is quite difficult.

The specifics of the use of household chainsaw technology

Trying to cut trees with a chain of household category with a low.power drive and a short bus is undesirable in terms of safety:

  • The performance of such work is extremely low;
  • risks of seizing a headset in a propyle increase;
  • High loads adversely affect the duration of the resource of such a tool.

The sphere of household chainsaws of the middle and small power category includes:

  • Trees bronation;
  • trimming thick branches;
  • Cutting locks in construction wood during the construction of log log cabins.

A one.time or any other roll of forest is a prerogative of powerful and productive models of a professional level. At the same time, it is not recommended to use large trees of a saw with an electric drive for dumping. With identical to gasoline models of power, the torque of the electric saw assortment is significantly lower than.

It is forbidden to work alone. The presence of a partner may be required to provide assistance in obtaining an injury. His duties also include additional control over the rolling process and the signal is given in the event of an emergency.

The initial stage of preparatory work

An independent roll of tanning trees is produced in a certain sequence.

Preparation for the main work begins with the study of safety requirements:

  • checking the correct sharpening of the saw chain and the serviceability of the chainsaw in general;
  • selection of comfortable shoes, clothes and protective equipment, the minimum list of which includes glasses and mittens.

At the second stage, it is necessary to calculate different options for the trajectory of falling the barrel with minimal damage to the surrounding area.

In the calculations, the following mandatory factors are proper:

Safety precautions

When performing the procedure for firing trees, it is necessary to ensure a full.fledged safety precautions for both private individuals and employees of organizations. You can not carry out the rolling of trees yourself. Be sure to have a partner. You should not make open fire during operation, and if any, you need to simmer it before turning on the chainsaw. You can’t smoke also. You should take care of protecting the face from sawdust in advance, as they always fly away when sawing a tree.

Before sawing a tree, you need to make sure that when falling it will not affect people, living beings, will not damage the cables or wires along which the current passes. It is forbidden to carry out work in strong winds. It is advisable to calculate in advance the direction of the fall of the barrel up to the exact circuit at which all rods and other elements are cleared so as not to damage the tree, and also not to cause its inertial coup.

When working with full.fledged, thick pillars, the chainsaws are held with both hands, while the tension is constantly felt.

Do not work when using only the extreme part of the saw, as this will lead to a strong return and automatic turning off the device, which can ruin all the work by making sloppy movements.

Когда распиливаются толстые столбы или массивные ветки, желательно поднимать бензопилу на уровень выше плеч.

How to cut a tree correctly. basic rules and technology

The main aspects necessary for compliance with the cutting of trees:

  • If the trees are dry, then no sources are allowed not only sparks, but also smoke, since adding gasoline to a dry tree can cause a fire, which not only inhibits the process of work, but also harms the environment.
  • Before turning on the chainsaw, you need to look around around. Neither children nor animals should be nearby. Only work comrades or bosses.
  • You need to always keep the chainsaw. Even in case of malfunctions and its automatic shutdown, you should behave carefully, since the fall of the device with a sharp part can lead to sad consequences.
  • Employees are prepared in advance for work on sawing a tree. Dense clothes and a mask are dressed on the face to close the whole body from a possible entry of dust and dirt.

To get rid of the continuous sound of the chainsaw, it is necessary to use soundproofing headphones, otherwise headaches are possible in prolonged and regular work.

First, all technological features are determined, only then you need to clearly plan the stages of work, which will help guaranteed to protect yourself from the effects of the weight of the falling tree. Even with extensive experience, it is necessary to constantly take care of their own security, since the highest number of injuries are obtained by workers who have long been accustomed to a constantly stressful and dangerous atmosphere in this area.

To quickly cut down the tree, it is necessary to carry out preparatory work in advance, ensure safety precautions, only then proceed to the event. It is enough to independently apply the positions that provides for a cutting scheme so that the success of the event is guaranteed.

Great importance is given to security technology. In order to correctly perform it, you need to prepare in advance, and also be careful about working throughout the time of interaction with wood.

Do not forget that absolutely every new tool, including Chinese chainsaws, needs to run.in, we also recommend reading an article about oil for lubrication of the chain of chainsaw.

Three classes of devices

Currently, a large number of chainsaws can be found on the market, which can be divided into three classes:

  • The first class includes simple household devices that are designed for simple home needs. Most often, such chainsaws have small power, but they cope with all their duties very well. Using such a chainsaw, you can cut off a rotten tree or prepare for the bath a firewood. Despite the fact that the functionality of such saws was minimal, this is easily compensated by ergonomic control and their slight weight.
  • The second class includes the so-called semi-professional models that are able to perform almost any work-from repair and construction tasks and up to the roll of trees. But at the same time, such models have one significant minus-they are not designed to work 8-10 hours a day. It is for this reason that they are called semi.professional. Most often, lumberjacks use such saws as knobs.
  • The third grade includes professional saws that are an excellent solution for people who specialize in forest cutting. Such devices can be used 10-15 hours a day, allowing you to work without a break for 8-10 hours.

How to work safely with a chainsaw?

Not everyone knows how to work with a chainsaw, so this issue is interested in everyone who has acquired this high.tech device. Some believe that everything is clear to them and do not even look in the instructions. But such actions can lead to a serious injury or to breakdown of a chainsaw in the future. Therefore, before starting work, do not be lazy and study the instructions well.

Preparation for work

First you need to make sure that the device chain is stretched correctly, for which you need to pull the upper links a little-while the shank should exit from the groove of the tire groove for several millimeters. Also, you need to ensure that the lower links do not sag. After that, try pulling the chain with your hand. it should be easy to stretch. If the tension of the chain is very strong, then it should be loosened. Next, you need to check in what position the inertial brake is located. its handle and the main handle should not be in contact, since when the chainsaw is turned on with a displaced inertial brake, the clutch may be damaged.

After checking the tension of the circuit, you can proceed to refueling the tool. To do this, the chainsaw must be installed on the horizontal surface and pour oil oil and fuel mixture into it. The best option is the fuel mixture of oil intended for two-stroke engines, and gasoline of the A-92 or A-95 brand. The ratio of gasoline and oil should be 1 to 40 or 1 to 50 (per liter of gasoline about 20-25 grams of oil).

For the motor and chain, you should choose a special lubricant designed for chainsaws, since such lubrication contains components that can extend the life of the cutting element and engine details. At the end of the audit, after carrying out all the procedures described above, you can launch a saw.

Remember that before launching the engine, you need to remove the saw from the place where it was made so that there was no fire. Install it on a stable solid base.

First start

After making sure that the chain does not contact with any surfaces, it is necessary to turn on the brake of the chain, moving the brake handle from yourself so that the chain does not start its rotation ahead of time. Since initially the engine is cold, it is necessary to fully pull out the lever that controls the air damper. Next, you should walk the toe of the leg into the posterior handle, holding the front handle with your hand, and pull the handle several times until the engine “sneezes”. Then it is necessary to transfer the air damper to the working position and start the saw, pressing shortly on the throttle and transferring the saw to idle. After that, you need to transfer the brake handle to a position on yourself and your chainsaw is ready to work.

  • Before starting work, it is necessary to check the brake of the chainsaw, for which you need to install it on some even surface and press the throttle. Next, it is necessary to activate the brake by pressing the handle. The brake is considered a worker if the chain stops.
  • Among other things, before starting work, you need to check the lubrication mechanism. To do this, you need to find any bright surface, start the tool and, holding it over this surface, increase the speed of the chain with a simple press on the throttle. If a small strip of oil appears on the surface, then everything is in order with the lubrication mechanism.

Design, species

Before describing how to cut a chainsaw correctly, you should slightly consider the design of the unit. Any gasoline saw consists of a two.stroke internal combustion engine, to which the control organs are attached, as well as a cutting tool (guide arrow and chain). The latter is driven by a stars associated with the crankshaft of the motor through the sloppy clutch clutch.

Since the engine is very warm during operation, to avoid obtaining burns, it is closed with protective shields. The design is also provided for an emergency brake, when using which the chain stops.

The market of such equipment offers chainsaws that are conditionally divided into three categories:

  • amateur, they are bitch cutters. These saws are suitable for home use: to saw firewood, dump one or more trees, tear them out. They differ in compact dimensions and small weight, which ensures the convenience of work, but their power is not particularly high;
  • semi.professional. Quite productive units that are suitable for pruning knots and trees, and for firing forests. They are called semi-professional due to the fact that their continuous work is allowed during the shift (8-10 hours);
  • Professional. Used for industrial rolls of forest. These are powerful saws that can work continuously for 10-12 hours.

For home use, an amateur version is quite suitable, but despite the fact that it is intended for domestic use, it is important to know how to properly saw a chainsaw related to this category.

Such an unit can be performed by the following actions:

But no matter what type of work is supposed, before cutting a chainsaw, it is necessary to complete the preparatory stage.

Preparatory stage

Preparation of the saw itself is reduced to refueling with its fuel mixture and oil for lubricating the cutting tool, checking the tension of the chain. When pouring gasoline, it is important not to shed it past the tank, and if this happened, then you need to carefully wipe the surface with clean rags. The same applies to oil.

The tension of the chain is checked very simply: it should not sag below the arrow. Then her fingers need to be pulled up. in the well.stretched chain, the shanks of the links should leave the groove of the arrow at the stretch site. Must check the ease of the cutting element along the guide.

Before working with a chainsaw, you need to prepare and timber. It is better to use special goats for a file of firewood in which the sawn blanks are laid (you can use one of the sticks as a deck). When cutting out, reliable fixation of the tree trunk is important. As for the roll, they are determined with the side in which the tree will be laid, they clear the place for it. In general, it is more convenient to work with an assistant who will bring timber and keep them when cutting.

After preparatory work, you can proceed directly to the process of sawing. The launch of the chainsaw is carried out according to the recommendations of the manufacturer.

Valka with tuning

If the question arises of how to cut a large tree near a private house with a small territory, it is worth considering the option of tacking with tuning. This means that the sawn tree must be pre.mounted to a high support so that it does not fall after the cut, but hung on a rope. This method will allow you to carefully cut down the tree and not damage the objects surrounding it.

It is worth noting that the tuning of the same trunk (below the sawing place) is extremely undesirable, because the cut off a piece of wood after the saw will swing strongly to the sides. The cut fragment thus can inflict a tree for a tree or damage the property located nearby.

Valka with dropping

If you are the owner of a private territory with a house, you can cut a tree next to the house legally. If it is high, the method of rolling with dumping will help. It begins with cutting the interfering of the lower branches. After that, you need to take the stairs and cut down the following, more voluminous branches, gradually proceeding to cutting thicker branches located above.

With a gradual movement around the tree trunk, a stepladder should be used during cutting branches during cutting. When its heights are no longer enough, you have to put on climbing equipment or make insurance from a strong rope. If the crown of the tree is large, some of its branches will also need to cut down.

For an independent construction of the safety system, you need:

  • take a rope (2.5 m), withstanding one ton to break;
  • Fold the rope by half;
  • Skip the folded cable between the legs so that the loop is behind;
  • tie in the area of ​​the belt of the node the wound;
  • wrap the ends of the rope around the belt;
  • Skip the ends of the wrapped rope into the loop from the back;
  • Tighten the ends pushed into the loop and tightly knit them in front on top of the knot;
  • hook for the “eight” carbine;
  • put on a carbine on the safety cable that needs to be wrapped around the barrel twice (this is best done over a massive bitch or branch).

To start the next stage of cutting, you need to climb into the tree peeled from branches, fixed with the help of safety equipment. In the process of cutting a tree with dropping, the barrel is sawn in parts 1-1.5 meters in length, starting from the upper tier. Arborrian or specialist in trees care is fixed below the cutting site of the next piece of the trunk.

How to blame the trees with a chainsaw. safety rules

The correct roll of large.sized chainsaw trees in the forest or on the site is not only a time.consuming, but traumatic process. The minimum error can cause big problems. It is not enough to have an instrument. The correct cut of trees requires compliance with safety precautions, which is prohibited to ignore:

  • The sober condition of the employee is any form of intoxication under the ban (alcohol or narcotic drugs). Otherwise, the risk of injury increases several times.
  • Before it is properly sawing and filling the tree, it is necessary to check the technical condition of the equipment: sharpening quality, chain tension, tire serviceability and other elements.
  • During a working engine, it is strictly forbidden to touch the cutting elements with your hands. If you need to somehow interact with the tool, we will first drown out the engine.
  • In the process we use special protective equipment for the eyes or scarf.
  • The chainsaw is very noisy. Before a roll we use bears or special headphones.
  • We definitely put on a helmet on the head. during the rolls it is possible to fall large branches.
  • Shoes are selected according to the rules. it should consist of strong materials (rough skin) with special tread on the sole, which prevent sliding. The toe of the boots is decorated with metal inserts that provide protection against injury in the event of a break in the chain and its hit.
  • Clothing from durable, dense materials that are well fitting the body. the risk of clutching the tool about the thing or its winding is significantly reduced.
  • IMPORTANT! During the roll of trees, we hold the chainsaw with both hands.
  • Washing is performed by several people.
  • You can not refuel a gas.fuel mixture in a closed room or during engine operation.
  • The chainsaw is transported in collected form and in a special case.

Do not know how to cut a tanning tree of a chainsaw as efficiently and without injury? We follow the safety rules and use the services of professionals.

How to blame the trees with a chainsaw. preparatory stage

The correct roll of large and small chainsaw trees provides for preliminary preparation, which is performed sequentially. The process begins with the assimilation and compliance with safety requirements. Then you need to calculate the different options for falling the barrel, which will pass without prejudice to the environment. In this case, they take into account:

The next stage of preparation provides for certain features:

  • Valka of trees in coastal zones deserves special attention. A trunk that has fallen into the water can create many problems and require additional expenses to finish the work.
  • It is necessary to decide on the ways of the waste if the situation during the roll gets out of control, and the tree will fall not to where it was planned. A dumped thick trunk in the future needs to be cut and taken out, which requires free space for the entrance of the equipment.
  • The exclusion of the risks of falling during the roll of branches. the problem is solved individually by a call of specialized equipment (rental of a crankshaft and t.D.).
  • Preparation of a work site for the safe movement of equipment and people. The territory is cleaned of branches, leaves and other garbage.

The position of the roller

In order not to get an injury when drilling a tree, a foller must always choose the right position. The location is considered correct, in which the foller can get away from the danger at any time. For this reason, before bringing down the trees, the operator must clean all the small shoots, for which you can stumble and fall. During the roll, the saw must be held with both hands and be in the area of ​​the opposite from the one where it is planned to dump the tree.

It is allowed to be in the zone of falling wood only in order to cut out the wedge, which is done first.

Safety precautions

When performing the procedure for firing trees, it is necessary to ensure a full.fledged safety precautions for both private individuals and employees of organizations. You can not carry out the rolling of trees yourself. Be sure to have a partner. You should not make open fire during operation, and if any, you need to simmer it before turning on the chainsaw. You can’t smoke also. You should take care of protecting the face from sawdust in advance, as they always fly away when sawing a tree.

Before sawing a tree, you need to make sure that when falling it will not affect people, living beings, will not damage the cables or wires along which the current passes. It is forbidden to carry out work in strong winds. It is advisable to calculate in advance the direction of the fall of the barrel up to the exact circuit at which all rods and other elements are cleared so as not to damage the tree, and also not to cause its inertial coup.

When working with full.fledged, thick pillars, the chainsaws are held with both hands, while the tension is constantly felt.

Do not work when using only the extreme part of the saw, as this will lead to a strong return and automatic turning off the device, which can ruin all the work by making sloppy movements.

Когда распиливаются толстые столбы или массивные ветки, желательно поднимать бензопилу на уровень выше плеч.

How to cut a tree correctly. basic rules and technology

The main aspects necessary for compliance with the cutting of trees:

  • If the trees are dry, then no sources are allowed not only sparks, but also smoke, since adding gasoline to a dry tree can cause a fire, which not only inhibits the process of work, but also harms the environment.
  • Before turning on the chainsaw, you need to look around around. Neither children nor animals should be nearby. Only work comrades or bosses.
  • You need to always keep the chainsaw. Even in case of malfunctions and its automatic shutdown, you should behave carefully, since the fall of the device with a sharp part can lead to sad consequences.
  • Employees are prepared in advance for work on sawing a tree. Dense clothes and a mask are dressed on the face to close the whole body from a possible entry of dust and dirt.

Tree Branches cutting machine

To get rid of the continuous sound of the chainsaw, it is necessary to use soundproofing headphones, otherwise headaches are possible in prolonged and regular work.

First, all technological features are determined, only then you need to clearly plan the stages of work, which will help guaranteed to protect yourself from the effects of the weight of the falling tree. Even with extensive experience, it is necessary to constantly take care of their own security, since the highest number of injuries are obtained by workers who have long been accustomed to a constantly stressful and dangerous atmosphere in this area.

Working with a chainsaw. How to cut trees correctly.

Chain saws are indispensable tools for gardeners, summer residents or homeowners. Although modern chain saws are very convenient and reliable, nevertheless, if operating is improper use, they can pose a serious danger. They should be operated with special vigilance in order to avoid accidents and get serious injuries. Therefore, it should always be remembered that working with a chainsaw requires special caution.Locate a tree

Be sure to read the drill operating manual. Start work only in the case of a complete understanding of the principles of proper handling of a chainsaw. All basic principles of safety regarding work with gasoline saw are more applicable for electric saw.

We present to your attention the basic methods of work and safety rules when working with a saw. In this article, we will talk about how to cut the trees of a chainsaw, pruning the branches and cutting off the trunks. Use personal protective equipment working with a saw.

Working with a chain saw, always wear tight.fitting clothes. Do not wear free clothes or jewelry. They can fall under the moving chain of saw.

When working with a chain saw. Use the following protective equipment:. durable gloves;. protective shoes with non.slip soles;. such means of eye protection as glasses made of non.glass, protective glasses or nets covering the face;. protective helmets;. noise liners or ear liners;. Masks or anti.fry respirators (when working in intensive dust areas).

Work only with a well.sharpened chain. In no case do not work with a dumb chain. The need to use force when working with a saw is a sure sign that the chain has become dull. Too small sawdust indicates the same. The sharpened chain gives large sawdust, and the saw itself crashes into a tree. Regularly check the tension of the circuit.

Pull the circuit with a tent tension regulator, turning it. Pull the chain until it is eliminated from the bottom of the tire; Check the tension by raising the end of the tire and pulling the chain. The chain is considered correctly stretched if, when the chain is pulled from the upper part of the tire, manually guide tender teeth do not leave the groove of the tire, but the chain easily moves at the hands. To avoid contact between hands and chain, use protective mittens to scroll the chain.

Long Trees Branch Cutter Machine|| Trees Branch Cutter Machine.

Spend the tension of the circuit regularly, do this no less than with each filling of the oil tank for the chain. If the chain is new, it must be checked more often, until it is being taken. Correctly stretched chain contributes to the safety of work and a long service life. Stick well work with a saw. Only carefully instructed adults should work with a chain saw. The new user must definitely read the operating manual and, in addition to this, undergo a detailed practical briefing. If you have no experience working with a saw, practice, sawing logs on supports (goats). Do not let go of the saw handles! Always hold the saw tightly, covering the handles with all your fingers. Right hand on the rear handle and left. At the front.

Any user, regardless of whether he is left.handed or not, must use this capture that reduces the risk of sawing a saw and helps to maintain control over it.

Saw one log at a time. Be extremely careful when you insert the saw into the already made drink. Do not try to cut the tire tip (diving sawing). Follow the rolling logs and other things that can be closed and pinch the chain or get into it. Use special guide tires that reduce the exposure to the reverse shock, as well as reducing the reverse blow with chains suitable for your saw. Stand a little to the left of the saw so that your body is not on the same line with a working chain. Do not lean too low. You can shake, lose balance and control over the saw.

Most accidents associated with the rejection of the saw occur in connection with the trimming of branches and branches. Make sure you have taken a stable position and that there are no items nearby that can prevent you or violate stability. With careless handling, the tire wasolation zone can come into contact with a branch, a close tree or other objects, and this can lead to a sawing of a saw.

Never use a chain saw for cutting above the shoulder level, and do not cut the bow of the tire. When working with a chain saw, never stand behind the saw, always hold the saw from the side, closer to yourself, this will not strain your hands and back with prolonged work.

Only having mastered, as it should, all the principles of working with a saw, you can start a roll of trees. You can’t bring down trees alone, someone should be close to an unforeseen case. Make a plan of the roll. Provide the direction of safe waste.

All principles regarding work related to a roll and cutting out also apply to the cutting of large branches.

Make sure your pose is stable regardless of whether you are standing still or you have to change the position of the legs. When working, the log should always be to you. For the best control, you should keep the saw as close to the body as possible. Before you bring down the tree, carefully inspect it. Make sure there are no dead branches and branches that may fall on you. Learn the natural slope of the tree, the location of large branches and the direction of the wind. This will help you determine which way the tree will fall. Clean the working platform around the tree. Before you bring down the tree, plan and clear the leaving route from the working area. Such a route should be laid in the direction opposite to the plan of the fall of the tree, at an angle of 45 ° to it.

With a tree roll, one should always strive to choose a direction where neither extraneous objects nor the terrain could interfere with the subsequent pruning of the branches and tear.off. The most important thing is that nothing interferes with your movements, and that you are in a stable position.

How to blame the trees with a chainsaw

Surely most gardeners at least once faced the need to cut down a tree in the country. for example, in order to prepare firewood for the winter. Bright the tree with a chainsaw

At first glance it may seem that this is a rather simple activity, especially since most summer residents have a chainsaw in the arsenal, and hardly anyone “in the old fashioned way” cuts trees with an ax. However, in fact, this work requires considerable efforts and skills. About how to blame the trees correctly, we will tell in this article. First of all, it is worth talking about safety measures, which, unfortunately, many neglect.

First, to work with a chainsaw, do not put on wide clothes and jewelry. Secondly, do not forget about protective equipment: special glasses, dense gloves, noise lords. Shoes should be non.slip. Before you bring down the trees with a chainsaw, be sure to check if the chain is imprisoned. It is also very important to pull it correctly. if everything is done correctly, when pulling the chain from the upper part of the tire, guide teeth should not leave the groove. Check the tension of the chain every time you fill the oil. Now directly about the work itself. Valka of trees in the country can be complicated by the fact that near the houses or various buildings can be located near.

In this regard, you need to carefully inspect the territory and plan the trajectory of the fall of the tree so that it does not damage nearby objects. Please note that it is extremely not recommended to carry out work in strong winds. If you want to cut down an emergency tree, make sure that there are no dead branches on it that may fall on you. In addition, you should think over the path of leaving the working area. there should not be any barriers on it. With a tree roll, it is important to prevent it from hanging in the branches of neighboring trees, this will not only give you a lot of inconvenience (after all, it will be quite problematic to remove it), but it can also be dangerous. It should also be understood that you do not just need to cut down the tree, but also process it in the future, so it is advisable to choose such a direction of the roll so that there are no barriers in further work (for example, the terrain or the presence of foreign objects).

Rolling technology cut a large tree

Valka of trees, especially large ones, requires certain knowledge and skills. Before performing the work, we advise you to familiarize yourself with safety precautions and some nuances that must be taken into account. About how to cut a tree correctly, we will tell in this article. The rolling room must be carried out in three doses. first the woods are performed, and only then the main cut.

The first stage is the upper file, it is made at an angle of 45 degrees at a depth of ¼ of the diameter of the barrel, from the planned fall of the tree. The second stage. the lower. It is performed on a horizontal line, before the connection with the upper file. Thus, the trunk should get a cut angle of 45 degrees. note. It is not necessary to cut a tree completely, this is fraught with the fact that it will be impossible to predict the direction of falling the barrel.

And finally, the final third stage. the main (gross) drank. Before proceeding to him, make sure that there are no people or animals at a distance of several meters (especially if you are going to cut down a tree in the city, gardening and other crowded places). The main cut is carried out from the side opposite the direction of the fall of the tree, parallel to the lower file (at a distance of 5 cm from it).

It is very important to leave the so.called hinges (unfinished), equal to about one tenth of the total diameter of the trunk. If it is smaller, or it will not be at all, the trajectory of the fall of a tree may change, and not in the direction you need. During operation, the saw must be slowly immersed in the barrel, the engine speed should be maximum.

Before the fall of the tree, insert the wedge into the main cut, it will avoid jamming the tire in the trunk. Carefully monitor the direction of movement of the barrel in order to quickly take measures when it is deviated from a given course. At the beginning of the fall fall, quickly remove the cut from the cut, turn it off and leave the working area. Please note that these actions must be performed as quickly as possible.

Husqvarna specialists, when developing a chainsaw, always listen to the opinion of professionals who operate daily tools in logging. Our goal. transfer their experience to the production of new models and thus make the tool even more advanced from the position of consumer. We believe that Husqvarna chainsaws should always meet the highest requirements for efficiency, safety, and environmental friendliness.

Husqvarna history. This is a set of knowledge that are passed down from generation to generation. We used and enriched them, and today we want to share our experience with you. After all, even if you do not often use a chainsaw, it will be useful for you to find out how professionals work with it.

The advice that we will give you are common. There may be special norms in your country that you must adhere to.

The appearance of the saw and the placement of control elements can vary depending on the model. We want you to have an idea of ​​the best way to use the Banzopila. At first it may seem that this information is too much, but a little practice. And you will soon learn to treat the tool confidently.

branch, tanning, tree, properly, barrel

If you are a novice user, then, if possible, start working with an experienced partner.

Husqvarna strongly recommends you to carefully read the instructions for the operation of the saw after studying this leadership and only then get for work.

We hope that working with the saw will be pleasant and the results will bring you satisfaction.

Chainsaw. an effective tool, which, however, may pose a danger to the operator if you apply. This is why we say: security. primarily. The most important component of the safety of work is overalls. Even if you just saw firewood for a fireplace, you must use individual protective equipment.