How to cut a hole in a plastic panel

How to seal a hole in the plastic panel Only repair with their own hands in the apartment photo, video,

Published by Untitled on January 16, 2012. 23:26.

The operation is a jewel, myself faced with such a difficulty and suffered all day. Need: office knife, glue for plastic or silicone, a whole panel of a similar coloring and a profile of plastic. Take out the splinters and long ribs (the ones that go all the way through the panel and connect the back and front of the panel). If they are very small, cut out the desired size from the new piece. In the cut out piece use a utility knife to cut the back part of the panel, leaving less than half of the long ribs. Next, with a letter opener cut out short strips of plastic from the profile, any profile (side, docking, it does not matter, you are interested in the surface of the surface) 5h1 cm, the amount depends on the size of the hole, you enough 4 or 6. Check the fit of the strips on the glued piece of plastic cut out by you. It should lie between the longitudinal ribs. Lubricate one half of each strip with silicone or plastic glue. You glue the strips from the inside to the front layer of the panel, wait until it dries, then grease the other half of the strips and glue the cut out patch to it.

still have the option of buying part of a seamless ceiling (klienka) and glue it. Or we can blow out the hole with the installation foam, cut the foam that came out and glue a patch on top of it. The look will be fine under any circumstances, but it will be more beautiful than the hole.

Published by Guest on February 16, 2014. 20:05.

There is an easier option.Take a similar plastic or find the remains of the ceiling surface.Cut a circle depending on the hole, so that it would slightly cover the hole. We cut the back of the circle (ribs) that would come out thin plastic bring the thickness with sandpaper.We glue a round bar on the hole.

The choice of material

In the bathrooms boxes are made of moisture-resistant plasterboard with ceramic tile or PVC wall panels. panels. Tiled boxes have an excellent appearance and unsurpassed reliability. But pipes, meters and taps tend to fail, and sometimes need to be replaced or repaired. Therefore, the possible disassembly of the boxes. Factors to consider.

Boxes covering pipes in the toilet plastic panels are easy to assemble and disassemble, the materials for installation are inexpensive, the design has a decent appearance.

What to consider before cutting

Before you cut the PVC-panels must be taken into account:

• Low resistance to heat. plastic is not designed to operate above 50. 60 ° C. At temperatures just above 100 ° C, it begins to melt and deform. Therefore, no tools should be used for cutting that heat the material.
• Working conditions. as the temperature falls to 0°C and below, the plastic becomes brittle. Cut plastic panels during winter operations must be extremely careful. It is desirable to cut in a room where the temperature is higher. Before installation, the panels are taken out into the shed or under a shed so they can adapt to the cold. In this case the increased fragility does not matter any more.
• Dimensions. standard length of the cladding sheet is 3 m. It is awkward to work with such large panels. But besides a normal cut lengthwise or crosswise, PVC curved cuts are required. Choose a more maneuverable tool for this.

Material has a uniform structure, so it can be cut in any direction. It is important to choose the right tool.

• There are voids behind the aluminum siding where the siding is not in contact with the siding of the house
• Insert a drill bit or a circular saw into the drill motor chuck.
• Place the tip of the drill bit in the center of the finished hole.
• Press lightly on the back of the motor.

The first drill bit is used for making big holes with diameter more than 11 mm. To make the hole smooth and clean, it is best to continue drilling until the tip comes out on the opposite side of the workpiece. Then turn the workpiece upside down and complete the drilling operation on the other side. The pilot drill has a centering tip and sharp cutting tips on opposite sides of the blade. The first drill bit is used to produce large holes in both the texture of wood and the sawn ends of beams and timbers. When using a drill bit it is always necessary to set the drilling speed to high speed.

Suitable fixtures for PVC panel ceilings

Point drills are divided into types according to different characteristics. According to the method of installation there are surface and recessed. The first type has a body below the ceiling level. As a result, it increases the angle of incidence of light and improves cooling. But the body is more prominent on the surface, which does not always look aesthetically.

How to cut a hole in plastic using a hole saw

Recessed luminaires are between the ceiling and the suspended ceiling, so the installation requires space. As a rule, when installing the ceiling level is lowered by 7-10 cm (the distance depends on the size of the lighting fixture). Luminaire in off-mounted form is less visible and overall surface looks more aesthetically pleasing. But the cooling deteriorates, you need to be especially careful in choosing the bulbs and observe the distance between the devices.

The body is made of different materials, most often. plastic or metal, less often. glass, crystal and others. Available in white, black, colored, with decorative overlays, crystal pendants, additional base illumination, etc. п.

Varies and type of bulbs, for which the products are designed:

Sometimes the level of protection from harsh environments (labeled with letters IP). This parameter is divided into two categories:

• Particle protection. indicated by numbers from 0 (no protection) to 5 (protects against the smallest particles, t. е. dust).
• Protection against water. from 0 to 8 (the maximum level, can withstand a long immersion).

For example, a model marked IP55 is protected against dust and small water jets.

How to properly make a crate for PVC panels

Trims can be made as a wooden or metal profile. C. The advantage of the crate is that you can additionally insulate the walls. And the insulation will be quite substantial. If you have a constant cold, it will help correct the situation. It is best to use mats of mineral wool for insulation. Those who like to listen quite loudly music, you can lay a layer of soundproofing on the walls.

Lattice itself on the walls is fastened with dowels or self-tapping screws. If the walls are crooked, the vertical slats are installed with a plumb line or level. For the substrate can be used pieces of rubber, scraps of the panels themselves.

The most convenient trim is the usual linear. Maximum step for PVC panels is 50 cm. The minimum is considered a step of 30 cm. All protrusions, openings, window jambs, wall corners must be framed. Laths of purlins should not be with hanging ends. The only exception will be the ledge of your window sill. For it cuts a special notch in the panel, which will be adjacent to it.

As you can see, it is quite easy to work with the panels, and most importantly the entire work is fast. The main thing. is to collect crates, and installing the panels is easier and quite fun.

How to cut a PVC panel properly?

To successfully cope with the task, it is worth knowing some secrets of cutting plastic. This will significantly reduce the number of rejected and spoiled panels and save the novice craftsman from unnecessary waste of time, money and above all. from injury.

• If you are doing finishing work in the cold season, do not cut panels that have just been brought in from the street. Allow them to warm up to room temperature. The best option is for them to spend at least 1 night in room temperature. Otherwise, the plastic, which becomes brittle in the cold, will break in large pieces and may crack along the entire length of the panel.
• Regardless of which way you choose to cut, place the panel face up (photo above), otherwise the panel may deform and its installation will be difficult. In addition, if you make the cut from the wrong side, the front side can be covered with microcracks, which will manifest themselves only over time, finally spoiling the design. It will not be superfluous to mark in advance the line of the cut, for this will work a simple pencil or marker (which can easily be erased from the surface after the work) and a student ruler.
• To cut several PVC-panels at a time, you need to stack them and make this stack two-point support, so the panels do not sag. It is also worth to keep the opposite edge of the pile against the wall, otherwise during the cutting the panels will shift and you will end up with parts of different lengths.

What to cut the PVC panel at home

Specialists site “Stroyvelikan” tried to cut the plastic panel with many tools. A variety of factors were evaluated in testing. speed, effort, curved cuts, risk of damaging the panel, and cut quality.

Stationery knife

We began cutting PVC with a box cutter with retractable blades. Along the mowing line of the marking lay a wooden rail, along which the front part was cut. After that we bent the fragments at the cutting point. We additionally cut the underside with a knife.

• a simple and accessible tool;
• With the right approach, an even cut was formed at the joint;
• It is difficult to damage the panel;
• Can be cut lengthwise and crosswise.
• You have to make some effort;
• The blades often break;
• The accuracy of the cut without a guide is impaired;
• You need a stable support.

A wood saw

Then we used a second tool. a fine-toothed wood saw. You can cut several panels on one marking at a time. When working, the cutting blade is lowered to the sharpest angle possible so that it does not jam. To minimize the risk of damaging the panels, we laid them face up.

Additionally! It is most convenient to use a wood saw with a tooth up to 3 mm for cross-cutting plastic elements. A box cutter is better for a longitudinal cut.

Metal hacksaw

After that we decided to use a metal hacksaw, which is also suitable for working with plastic. The fine toothing slows down the installation process considerably, but allows a smooth cut lengthwise and crosswise. So you have to sacrifice performance in favor of quality.

The jigsaw

After testing the hand tools, we move on to electric tools. First evaluated the electric jigsaw, on which we set the saw with a fine tooth T 102 H. It turned out to be quite comfortable to cut the PVC panels, not only crosswise or lengthwise, but also along curvilinear markings.

• a clean cut in all directions;
• minimum chip formation;
• high level of performance;
• Little effort at work;
• possibility of shaped cutouts.
• costs several times more than a manual tool;
• it requires a power connection;
• PVC panels are damaged if they are not pressed properly due to sudden reciprocating movements.

angle grinder

In the last place we used a small angle grinder with a 1 mm thick wheel on metal. Start cutting plastic panels in all directions. The result is an even cut without nicks and chips. Maximum productivity is achieved through simple and clear movements, as well as the ability to work on the weight.

For your information! You can cut wall and ceiling panels of PVC, using a drill with a special attachment in the form of a cutting disc. The advantages and disadvantages are the same as with the angle grinder.