How to cut a skirting board at an angle

Applying a miter box template

To cut the plinth in the corner to the ceiling as evenly as possible, you can use a paper, cardboard or wooden template instead of a regular miter box. Two parallel mowing lines are applied to it, then a central point is found and any necessary angle is laid from it with the help of a protractor. Before you cut the corner of the ceiling plinth without a miter box, you should double-check the size of the inner or outer corners between the walls of the room, using the same protractor.

skirting, board, angle

The principle of cutting corners using a template is similar to using a standard miter box. In this case, the workpiece must be pressed against the parallel mowing line and, setting the hacksaw at the desired angle, saw off the workpiece.

Cutting skirting boards for ceiling decoration

Another type of ceiling plinth is made of extruded polystyrene foam. They are much denser than ordinary foam products (therefore they do not crumble), they are a little more expensive, but they are also somewhat more difficult to cut. For work, you can use the same knife or hacksaw for metal.

The most expensive skirting boards are made of polyurethane. These are elastic, strong and moisture resistant products that are very easy to cut with a construction knife. True, they cannot be used in all rooms, since polyurethane is sensitive to high temperatures. it deforms, begins to crack or crack.

For working with wooden skirting boards, only a hacksaw with fine teeth is suitable, you can use a metal tool.

Marking on the ceiling for making a corner on the skirting board

There are different ways of how to correctly make a corner on a skirting board. Some are easier to do, others are more difficult. One of these methods is to mark the plinth on the ceiling. True, it is not very convenient to cut the plinth by weight, but this method is not inferior to all others in accuracy. Before cutting the plinth to the ceiling, it is applied to the surface, while all the imperfections and irregularities of the walls, as well as the size of the corners, are immediately taken into account.

Let’s consider in detail how to correctly make the corners on the ceiling plinths using this technique:

  • First, two mating plinths must be cut at an angle of 90º;
  • One of the blanks is pressed against the wall, and its end is abutted against the opposite wall. Then the outline of the workpiece is drawn on the ceiling.
  • At the next stage, they take the second plank and press it with its butt against the wall in the same way. Outline the line.
  • At the intersection of the lines obtained, a point is set, along which further trimming of the baseboards will be carried out.
  • Then each of the strips is alternately applied to the ceiling again and the cutting point is transferred to the blanks.
  • From this point to the corner of the plinth, a diagonal cutting line is drawn.

Using the obtained fishing lines, cut off unnecessary sections of the baseboards, then join the mating segments, checking the correctness and completeness of the fit. “How to cut a corner of a ceiling plinth. simple and correct ways”.

It should be noted that this method is more often used for internal corners.

How to cut a corner of a ceiling plinth. proven methods and techniques

Ceiling skirting boards are very often used for decorating rooms. They give the ceiling a complete look, allow you to convey a particular style in the interior. In addition, they serve to mask the joints between walls and ceilings, where two different materials are mated. Although not always such elements are present in the premises, they make the interior more complete. In the material below, we will tell you in detail how to cut the corner of the ceiling plinth, since in such places the joining of individual elements is often a problem for inexperienced builders.

If the room has a simple shape, then only the inner corners will need to be cut. But in rooms of a more complex configuration, with columns, partitions and niches, there will also be external corners. For decorative elements to look beautiful, trimming must be done correctly and accurately, otherwise the appearance of the ceiling will be spoiled.

To trim the ceiling plinth in the corners as best as possible, you can use quality and sharp tools or other means. The type of tool that will be used to cut skirting boards depends on the type of material used to make them. So, ceiling plinths are made of PVC, foam, polyurethane and wood.

The cheapest option is PVC skirting boards. They are soft, so it is easy to leave dents and creases on them, which cannot be fixed in any way. In addition, this material has the ability to attract dust. A hacksaw or a sharp knife is suitable for cutting such skirting boards.

Another fairly cheap type of material is polystyrene foam skirting boards. They crumble easily, so only a sharp knife or a metal hacksaw should be used to trim the corners of the ceiling plinth. Movements should be soft, without pressure.

Using a miter box to cut skirting boards

In carpentry, a special device made of wood, metal or plastic is often used. a miter box. Special cuts are made in it, which allow an even cut at 90º, 45º, and in more complex devices. even at 60º. There are also professional miter boxes equipped with a swivel mechanism. In them, the cutting tool can be installed and fixed at any angle to the workpiece. Before making a ceiling plinth in the corners, you need to understand the details.

To cut the inner corner of a ceiling plinth using a miter box, you must:

  • First, the skirting board must be attached to the ceiling surface and mark the length.
  • Now a piece of plinth is placed in the miter box in the same position as it should be placed on the ceiling.
  • The plinth is tightly pressed against the back wall of the miter box.
  • Hold the work piece with one hand to keep it from shifting while cutting.
  • The hacksaw is set at an angle of 45º to the workpiece.
  • Cut the plinth, controlling the degree of pressure of the hacksaw, so as not to damage the product.
  • Then proceed to cutting the counter piece of the skirting board. It is also applied to the far wall of the miter box.
  • The workpiece is pressed and held by hand so that it does not move.
  • The hacksaw is installed at an angle of 45º to the workpiece so that the direction of the cut is opposite to the first element of the plinth.
  • Cut off the corner of the plinth.

After trimming the ceiling plinths in the corners, they proceed to the joining of the resulting elements. If the cutting was carried out accurately, they will fit snugly together.

Please note that it is recommended to start cutting the inner corner of the skirting board from the front side. Then the cut line will be more accurate and even. As for the wooden elements, then all the flaws on them will need to be cleaned up with a file. “How to properly cut the ceiling plinth in the corners. options and methods for plinths from different materials”.

Let’s take a look at how to cut the outer corner of a ceiling plinth using a miter box:

  • It is best to start marking and measuring the ceiling plinth from the inner corner, and only after completing it, start cutting the outer corner. Otherwise, the plank may be short, not enough to fill the entire length of the ceiling.
  • The plinth is applied to the ceiling and its length is marked.
  • Then the workpiece is placed in a miter box and pressed against the front wall.
  • The hacksaw is placed at an angle of 45º and, holding the workpiece with your hand, saw off the corner.
  • Similarly, you must cut off the opposite part of the outer corner.
  • The workpiece is pressed against the front of the miter box.
  • The hacksaw is placed at an angle of 45º to the plinth and the workpiece is sawn off.

At the end of the work, the pieces of the skirting board are joined together, checking if everything is done correctly and evenly.

It should be noted that the miter box can help to cut the corner of the ceiling plinth as evenly as possible only if the walls are strictly perpendicular. If they are uneven and the angles are not accurate, this device is unlikely to be useful. “How to properly cut the corner of the ceiling plinth. rules and methods”.

How to make a miter box yourself

Often the only way to cut the corner of the ceiling plinth evenly is to use special tools so that the tool does not move to the side during the cutting process. In this case, you can make a miter box yourself.

Option 1. A box in the shape of the letter P is made of three boards. The required corners are marked on the walls of the box and the slots are cut out in the appropriate places. The result is a complete adaptation.

Option 2. Sometimes it is quite difficult to make the corners of the skirting boards on the ceiling as even as possible, especially if you have to keep the workpiece by weight. In this case, you can use a homemade device. Take two boards and knock them down in the shape of a corner. Then, on a sheet of paper or cardboard, they draw a mowing line with the desired angles, apply a template to the corner. Then the plinth is pressed, a template is placed under the cutting site and the corner is sawn off along the lines.

Option 3. If you are still in doubt about how to properly cut the corner of the skirting board, almost any household item, the shape of which allows you to form a corner, can help with this. It can be a chair or a table, just set against the wall.

To understand how to properly cut the ceiling plinth, you should also familiarize yourself with the rule for measuring blanks. So, to complete the inner corner, the length begins to measure right from the beginning of the corner. But to determine the outer corner, it should be borne in mind that it will be issued into the space of the room by the amount of the width of the product.

There is no need to rush and fix the workpieces before the mating skirting boards have been made in the corner. In order not to redo the work, you must first make sure that the mating surfaces are tightly adjacent to each other and to the ceiling. Small flaws can be corrected with a file, a thin nail file or a knife, depending on the material of the products.

If cutting off the skirting boards in the corners did not work out perfectly, small gaps can be simply putty. In general, the process of trimming skirting boards in the corners is not at all difficult. However, for training, you can take a few small pieces of the baseboard and practice on them.

Stencil cutting

The method is recommended for cutting products intended for installation in non-standard-shaped rooms with angles that differ from the standard mark of 90 degrees. Stencils for the desired angle can be made from paper or thin cardboard. First, strips are cut from the rough material, which have exactly the same width as the skirting board. Then they are applied to the corner and fixed, after which they are cut to the shape of the corner. Then, according to the stencils received, the plinth itself is cut at the required angle.

Stencil cutting of plastic skirting boards

How to properly trim the corners of the skirting board

Since it is hard plastic skirting boards that are increasingly used during repairs, it is about them that will be discussed. Their installation is inevitably associated with the need to cut and form beautiful joints in the corners. The quality of all work and the appearance of the room where the repair is being made will depend on how the plinth will be joined, in general.

Useful Tips

Experienced craftsmen recommend starting the installation of the skirting board from the inner corner. At the junction of the two walls, which form the inner corner, the cut on the skirting boards will be 45 degrees (in a room with correct and accurate geometry). It is recommended to cut with a miter box. this is the only way to achieve a perfectly even cut.

Cutting floor and ceiling plinths with a miter box

Advice! If necessary, you can slightly adjust the skirting boards to each other using a grinder or rasp, slightly “removing” their edges.

In general, in any case, the cut edges of plastic skirting boards should be sanded. this way it will be possible to get rid of sharp edges, and it will be easier to work. And the skirting boards with cable channels are cut only after the product has been disassembled. the decorative strip designed to hide the wires and attachment points of the skirting board is cut separately.

The plinth of the desired size is cut

It is recommended that immediately before installing the plinth, cut the segments to the required length and arrange the corners so as not to be distracted by this procedure during the assembly of the plinth. You should not neglect the use of additional elements. plugs, corners and other products for the baseboard. With their help, it will be possible to give the finished work a complete and harmonious look.

Advice! If the corners where the skirting board is laid and joined are uneven, then even decorative plugs and other elements can be trimmed if necessary.

It is very easy to cut skirting boards at any angle with this device.

Methods for cutting plastic skirting boards

Cutting skirting boards is seemingly simple, but responsible. If the corners are cut incorrectly, they will not fit correctly and all the work will go to waste, since the product will no longer have a beautiful appearance. there will be gaps between two sections of the baseboard and decorative inserts (corners, connecting elements, etc.).

Most often, an ordinary metal hacksaw, which has fine teeth, is used to cut the plinth. However, for thin skirting boards, it will not work, since the product will simply tear under the influence of this tool.

Plastic skirting board cutting angle grinder

Sometimes the plinth is cut with metal scissors. But the method also has its drawbacks, because the product can be crumpled under the pressure of the blades. Less common, but still used is an angle grinder. However, the cutting line after it can be inaccurate, as the tool often “tears” soft plastic. Especially often this method turns out to be unsuccessful for beginners in the world of repair who do not yet know how to fully control the work. So the angle grinder can be attributed to rather specific methods.

Metal scissors

On a note! You can use a sharpened knife or utility knife to cut thin skirting boards. But such work requires some skill, therefore it is recommended to first practice on the scraps of the old plastic skirting board.

The most important thing in the procedure for cutting skirting boards is the observance of the required geometry. The procedure is never performed “by eye”, the accuracy of measurements and accuracy are important here. Therefore, there are other methods for cutting skirting boards.

The absence of fittings implies the use of other methods of connecting skirting boards. This is an option with and without clipping templates.

How to cut off a plastic skirting board: how to cut it off and how to do it correctly, cutting methods

A skirting board is an essential element for decorating a room and giving it a complete and neat look. It can be made of various materials, but the plastic skirting board is especially popular now. It is easy to install, but even in this process there are some subtleties that are important to know about. How to cut a plastic skirting board correctly so that you can neatly dock it in the corners?

How to cut a plastic skirting board

How to cut a plastic skirting board

If the angle in the room where it is planned to finish the joints of the walls and the floor with a plinth is 90 degrees, which happens extremely rarely, then the cuts of the plinths should have an angle of 45 degrees each. Such a cut is the easiest to make, especially with the use of a miter box. It is enough to insert the plinth into the miter box, then select a groove at 45 degrees and make a cut.

Cut 45 degree corner skirtingboard, how I cut an external mitre, outside corner on skirting boards.

However, such angles of 90 degrees in rooms are extremely rare, usually they differ by several values ​​in one direction or another. And in some rooms, the corners may even be larger. Then the cutting is done differently: a marking is drawn on the floor with a pencil, where the border of the location of the plinth is drawn on one and the other side of the corner. you get a small rhombus. The diagonal of this rhombus will be the very cutting line of the product. Next, a plinth is applied to the marking, on which the marking is performed in accordance with the diagonal of the rhombus. If you draw a straight line from this mark to the corner of the plinth, then you get the very necessary cutting line.

Cutting the corner on the skirting board

Advice! When trimming the skirting board, it is recommended to saw off a little less than necessary. In case of an error, this will correct the situation by lightly processing the edges of the product by hand and adjust the skirting board to the desired size.

The outer corners of the skirting boards are formed a little differently, or rather, in a room with ideal geometry, you can also cut products at an angle of 45 degrees (but in a different direction) and, after joining, close the edges with a plug. Non-standard corners are cut like this: one of the skirting boards is applied to one of the walls, its borders are marked with a pencil. The same procedure is performed with another product. again a rhombus flaunts on the floor, the diagonal of which will become a guide for cutting products.

Decoration of the outer corner of the plastic skirting board

The main types of floor skirting boards

The wooden skirting board is a classic. It is a natural product, as it is made from solid wood. This type is distinguished by its high strength and durability. the skirting boards, installed back in the times of the USSR, still serve faithfully in some apartments and houses. Now they are made mainly from pine wood, but there are also products from walnut, oak, ash and other species. However, due to this, the cost of products increases. not everyone can afford such skirting boards.

Wooden floor plinth

Because of this, veneered skirting boards have appeared on the market. their are an order of magnitude lower. However, outwardly, they practically do not differ from products made of expensive wood. The fact is that their upper part, which plays a decorative role, is just made of a thin layer of expensive wood. Without certain knowledge and experience, it is almost impossible to distinguish veneered plinth from ordinary wooden skirting.

On a note! For cutting skirting boards. wood and veneer. use a regular wood saw.

It is convenient to cut wooden skirting boards with a hacksaw for metal

Plastic skirting boards, that is, made of PVC, are especially popular now. It has partially displaced conventional wooden products from the market, as it has a number of advantages:

  • looks beautiful and neat. it is able to imitate natural wood products;
  • easy to install, flexible and very easy to cut;
  • can serve as a cable channel for laying wires;
  • not afraid of exposure to water, and also does not rot, mold does not start on it;
  • is inexpensive compared to wood or veneered products.

Plastic skirting board is made of polyvinyl chloride, which is passed through special forms under high pressure. After the mass has solidified, a neat plastic product is obtained.

On a note! Some manufacturers decorate the edges of plastic skirting boards with rubber. This measure helps the product not to slip on walls and floors during installation and to adhere tightly to surfaces.

Plastic skirting board

Plastic skirting boards are of several types. for example, used for carpet (they have a special shape in the form of the letter G, fix the material) or for linoleum. There are also universal products that can be installed on any kind of flooring. They can be classified and depending on the hardness.

Table. Types of plastic skirting boards depending on the hardness.

Flexible plastic skirting boards

Cutting skirting boards with a miter box

For the correct trimming of the plinth, a special device was invented, which was called the miter box. It is a small block with a notch for the skirting board and with gaps located at different angles. for the cutting tool.

With the help of a miter box, you can get neat and even cuts. The plinth is fixed inside the product, then the angle and direction of cut required in a particular case is selected.

On a note! If it is necessary to form a beautiful angle using a miter box, then one piece of the plinth is cut at one angle, and the second. in a mirror image.

We make a miter box with our own hands

When working with a miter box, it is important to ensure that the edges of the skirting board protrude a short distance beyond the edges of the selected slot. If the trimming tool is wider than the skirting board itself, it is recommended to securely fix the product inside the miter box before trimming. Otherwise, the plinth may move inside, the cut angle will constantly change, because of which it (cut) will turn out to be incorrect and incorrect.

Making cuts for joining skirting boards using a miter box

Important! The pressure on the skirting board should be moderate when cutting. Otherwise, it may break.

Cutting with a rotary miter box

Appointment of the miter box

The procedure for cutting the corners of the ceiling skirting boards is as follows:

  • Attach the baguette to the area of ​​the future fastening. This will make it possible to accurately mark the cutting site.
  • Place the plinth in the recess of the miter box so that the back side fits snugly against the underside of the tool. The surface to be glued must be oriented upwards.
  • The ceiling plinth is cut along a 45-degree guide. You can use a knife or saw to clean up uneven cuts.

Trimming the oblique corners of the ceiling plinth

As practice shows, the corners in the room are far from always even. It depends on the quality of the preparation of the walls and the architectural features of the room. In such a situation, an ordinary miter box or marking sheet turns out to be powerless, since you have to deal with other parameters of the butt sections. blunt, or vice versa, sharp. Most often, this can be found in old-style houses, village buildings and summer cottages. There is only one way out in this situation. to make markup in place.

The order of work, how to cut the ceiling plinth at a non-standard angle:

  • The baguette is positioned on any wall in such a way as to achieve abutment of the end against the adjacent wall.
  • On the surface of the ceiling, a line is drawn along the cut of the plinth.
  • The other wall is marked in the same way.
  • At the point of intersection of two lines, a mark is made on the surface of the baguette.
  • By connecting the mark and the corner part, cut off.
  • A similar procedure, how to cut the corner of the ceiling plinth, is carried out on another workpiece, which will be on the adjoining side.
  • When installing workpieces, it is important to achieve a snug fit.

How to cut ceiling skirting boards. cutting tools and rules

Any kind of ceiling finish will look unfinished without a skirting board. With the help of these elements, you can reliably hide the unevenness of the joints between the wall and the ceiling.

When there is no miter box

It so happens that the miter box is not at hand. In this case, you have to be smart. Before sawing the ceiling plinth, it is recommended to apply the cutting direction on paper, cardboard or wallpaper. It will act as a guide for applying blanks to it when cutting. To make the drawing correctly, I attach a piece of baguette to the paper and draw a couple of parallel lines. They will serve as the side boundaries of the workpiece.

Next, using a school protractor, measure 45 degrees and plot the direction of the cut. In work, a similar drawing is used in the same way as a miter box: you need to put a workpiece and cut off all protruding parts along the mowing line. The disadvantage of this method is that the cutting tool has to be held in weight above the drawn line. There are no special saw guides here.

How to cut outside corners

Sometimes there are corners protruding outward in the room, which are much more difficult to trim. There are also several ways to implement this procedure, how to cut skirting boards to the ceiling. The simplest is to use a miter box: in this case, the outer sections of the joints must be cut so that part of the ceiling is on the plane of the miter box, and the side from the wall is adjacent to the wall of the tool. In addition, you can apply spot markings by running the line along the base of the ceiling. The procedure here is very similar to the preparation of the inner corners.

There is also an option with a wall marking, when the baguette is positioned parallel to the ceiling and the line is drawn along the lower cut. In the presence of excessive roundness of the outer corner, a sharp painting knife enters the work. At the point of convergence, the line is drawn exactly along the cut of the future docking: it must connect the ceiling and wall mark. The resulting marking is a guide for sawing off or cutting off the butt end.

Recommendations for the selection of tools

The process of choosing a specific fixture for cutting the corners of the ceiling plinth primarily depends on the material for making the baguette:

  • PVC. Plastic products are prone to damage from any careless pressing. Since their elasticity is weak, the dents are not restored back. This point should be taken into account, and do not press too much on the product when trimming corners. As a tool, how to cut a ceiling plinth on a miter box, it is best to use a sharp construction knife or a hacksaw for metal.
  • Styrofoam. A very popular option for the manufacture of ceiling plinths and other decorative elements (moldings, chandelier linings, etc.). Foam products are very lightweight, which makes installation much easier. Cut the corners of these friezes carefully due to their fragility.
  • Wood. Wood baguettes are elite expensive products that are distinguished by their external beauty and style. A hacksaw for metal is usually used to cut this type of ceiling plinth. In the process of work, it is necessary to regularly clean the teeth, because they get clogged up pretty quickly by shavings. It is recommended to choose a hacksaw blade with a close tooth pitch.

Self-made miter box

Given the simplicity of the miter box design, it is often made with your own hands from wood and steel. The parameters of the product do not matter much, but as their width increases, the accuracy of the cuts increases. It should be borne in mind that if the width of the device exceeds the length of the hacksaw, the sawing procedure will face additional difficulties.

How to Cut & Install Skirting Board, Baseboard Internal Corners

The first step is to outline the central axis of the workpiece, which requires a long steel ruler. Next, make an indent by 0.5 of the width of the workpiece from the points of intersection of the axis and the edges, to apply marks. These mowing lines must be connected crosswise. An existing base is used to mark the side walls of the tool. When drawing lines, they are guided by the existing marking, from which transverse straight lines depart.

Then you can proceed to the assembly procedure for the miter box. Self-tapping screws are used to fix wooden or chipboard walls to the base. If these elements are made of steel, bolted angles will be required. The fully assembled structure is equipped with saw guides and the attachment is ready for use. With its help, you can significantly speed up the procedure for repair and finishing work, without wasting time on manually cutting corners. It takes a little experience to cut the ceiling plinth with a miter box as it should.

How to get the correct angle

Most of the problems when working with skirting boards arise in the design of corners. Since the surface of the products is complex, it will not be possible to simply cut off at the desired angle: it is also necessary to cut it so that they dock and, preferably, without large gaps. In reality, there are several ways to make the corner of a ceiling plinth perfect (or almost).

How to make a corner of a ceiling plinth without a miter box

Few people in apartments or houses have angles exactly 90 °. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything “in place”. under the ceiling.

You will need a finely contoured pencil (hard. it is not so visible on the ceiling, but leaves quite clear marks near), a small piece of plinth, a ruler and a good stationery knife if you work with polyurethane (polystyrene) baguettes or a metal saw to work with other materials.

Apply the plinth to the corner, draw along the outer edge with a pencil. Apply to the other side of the corner, also mark. You have a cross on the ceiling, the center of which marks the place where the plinths of the ceiling plinth should converge (look at the photo). Having installed a piece of plinth in the corner, which will be glued there and resting it with its end on the wall, transfer the mark to it.

How to make corners on skirting boards without using special tools

Now take a ruler and connect the edge of the skirting board with the marked mark. If you just put the plinth on the table and cut along the mowing line, the two parts in the corner will still not fold: the inner part will interfere. It can be trimmed later by trying on the ceiling. The second way is to set the piece to be cut on the table with the piece that will be on the ceiling. And cut along the mowing line, but keeping the knife at an angle of about 45 °. It will still be necessary to correct, but much less (and less chance of error).

Repeat the same operation with the second bar. Put it against the desired wall, rest the butt against the adjoining wall, mark the place where the cross is drawn, draw the line and then cut it off. Correction Carried out “dry” without applying glue.

You repeat exactly the same steps for the outer (protruding) corner. Now you know another way to make a corner of a ceiling plinth, and without a scissor or other special devices.

With decorative corners

There is one more, the easiest way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory decorative corners. They are installed in a corner, strips are glued to them closely. It is very easy to cut them if necessary: ​​by a few millimeters with an ordinary clerical knife.

Examples of finished fillet corners

Using a miter box

If the corners and walls in the room are even, you can use a special carpentry tool. a miter box. This is an inverted U-shaped chute in which the mowing line is marked for cutting at 90 ° and 45 °. The part in which you need to make a gash is laid inside, a saw is inserted into the guides. The part is held in place, cut at the desired angle.

This is what the miter box looks like. Can be plastic, wood or metal

In the case of skirting boards, not everything is so simple: they must simultaneously adjoin two surfaces, therefore they must be pressed against one or the other wall of the miter box. When working with ceilings, they are pressed in the side closest to you.

The sequence of actions when finishing the outer corner, you need to make a gash at an angle of 45 degrees. Place the miter box in front of you. Trying on how the plinth will be located, determining which part of it will be attached to the ceiling. In order not to get confused and cut off the ceiling plinth correctly, put the strip that will be located on the right on the right, the one on the left on the left.

How to cut a corner on a ceiling plinth: install it correctly in a miter box

Press the part that is on the ceiling to the bottom of the miter box. The other side is closer to you and raised. Lean it on the wall of the device so that it does not stagger when cutting. That is, the front part of the skirting board turns out to be turned away from you. Do the cutting direction as shown in the photo below. By folding the two cut pieces together, you get a protruding outer or outer corner.

How to make the outer corner of a skirting board using a chair

First put the sawn-off parts in place “dry”, without applying glue. If the geometry of the corner is not so perfect, you can tweak it a little with a knife. It is easier to cover small errors with a special putty.

The situation is very similar with the inner corner of the skirting board. First you try on which side will be on the ceiling, press this part to the bottom of the miter box, lean the second part on the wall closest to you and make cuts as shown in the photo below.

How to make an inner corner of a ceiling plinth using a miter box

And again, first try on without applying glue, if necessary, slightly adjust. Then apply a thin bead of glue to both surfaces that will adhere to the wall or ceiling.

Your own version of how to use the miter box correctly is shown in the video.

What is it made of and what is it called

The very first skirting boards on the ceiling were made of plaster. They were cast in special molds and then installed on the ceiling with mortar. Such figured ornaments were called fillets. Today, you can rarely see them: they are expensive, and outwardly they are almost indistinguishable from the cheaper options. And the name is almost lost.

The most popular ceiling skirting boards are made of polyurethane or polystyrene. They are inexpensive, look great, easy to install, have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. An exception is wooden houses with a corresponding interior. Wooden products are most often used here. the style dictates its conditions.

There is also a similar plastic finish. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips. they are not afraid of damp.

You need to cut the ceiling plinth in the corners of any material in one of the ways described below. The only exception is plastic skirting boards: you can arrange such a corner only using ready-made corners.

How and how to cut

Working with skirting boards made from different materials means using different cutting tools. When working with a wooden skirting board, it is more convenient to work with a saw on wood. All others, including plastic ones, made of foam and other polymers, are better cut with a blade for metal. The result is a smoother cut, less burr. Saws are usually used when working with a miter box.

Corner design looks attractive

When working with polystyrene skirting boards without special devices, they are cut with a good office knife. Its blade is quite thin and even, the cut is smooth, not wrinkled. If you use a saw with polyurethane or polystyrene, do not press hard: you can wrinkle.

In general, to get used to the tool and material a little, take a piece and practice on it: cut, saw, trim. So there will be fewer problems when working.

How to cut ceiling plinth in corners

The quality of the ceiling finish greatly affects the appearance of the room. Therefore, they try to do everything perfectly, or very close to it. The finishing touch to the design is the ceiling plinth. They give the finish a complete and holistic look. The strips themselves are mounted on flat surfaces simply: on special white glue, but problems arise with the design of the corners. Without knowing how to make the corner of the skirting board correctly, a lot of material deteriorates. How and what to cut it in the corners and tell you.

How to cut a plastic skirting board?

A very good alternative to the skirting boards described above. plastic skirting boards. The latter almost completely forced out wooden products from the market. Their task of creating contrast and hiding the wiring, plinths made of plastic perform in full.

I advise you to read: DIY plastic skirting board installation

But in order for them to fulfill their role truly efficiently, you need to know exactly how to cut a floor plinth made of plastic. PVC panels have a hollow and flexible structure, the typical cutting method, as well as for wood, will not work. As a tool, we will use a hacksaw for metal with small teeth, as mentioned earlier. Or use metal scissors to make the perfect cut on the thinnest skirting board.

How to cut a plastic skirting board. tool selection

Plinth is an indispensable part of room design. For example, plastic products are gradually replacing wooden ones. Functionality and convenience are inherent in this finishing material, and it creates an aesthetic flow of the wall to the floor or to the ceiling. In the absence of finishing, containing the presence of plinth strips, even offices designed in the same style seem unfinished. The problem lies in the loose abutment of the floor slab to the wall. This creates rough seams that are removed by skirting boards. Fixation is easy to implement without the help of professionals, it is based on the knowledge of how to cut a plastic skirting board and in what ways to install.

How and how to properly cut a plastic baseboard. How to cut a plastic skirting board to the floor

Skirting board trimming instructions

Consider how the plinth is trimmed using a miter box and a hacksaw.

After all the dimensions taken, the plinth is placed in the inner part of the miter box and pressed against one of its walls.

The plinth fits into the inside of the miter box

With the help of a hacksaw, the plinth is trimmed. The cutting (sawing) tool is inserted into the selected groove. the cut is made.

Cutting the floor plinth

However, sometimes it is enough to cut plastic skirting boards at a right angle. now a large number of various additional products for them have appeared on sale. For example, there are corners that will allow you to hide even cuts and decorate everything beautifully. For your attention. instructions for installing plastic skirting boards.

How to fix the skirting board? The answer is here!

In general, all existing methods of fixing skirting boards can be divided into two categories. installation by fixing to the floor and installation to walls. You will have to choose depending on the type of skirting board and the design features of the living space. Read more in this article.

All measurements are taken. the required length for the skirting boards is determined. These values ​​are plotted on two products, from which corners will be formed.

The required length of the skirting boards is measured

Another photo of the process

Skirting boards are cut with a miter box and any cutting tool and applied to the walls. this is necessary to make sure that the products are cut correctly and are of the required length.

Skirting boards are applied

If everything is done correctly, the plinths are screwed to the wall with screws and dowels. But before that, plugs or corners are put on their ends.

A corner is put on the plinth

At the outer corners of the skirting boards are interconnected with special plastic devices.

Outside corner joint

Skirting connection for outer corner

The plinth is installed in the assigned place and screwed to the wall with self-tapping screws.

Screwing on the plastic skirting board

Next, the cable is laid in cable channels. It stretches under all corners and plugs.

Cable laying procedure

The cable duct with laid wires is closed with a decorative plug.

Installing a bezel blank

The outer corners are closed with special corner plugs, which are simply put on the edges of the skirting boards that form the corner.

Outside corner decorative corner

Stencil cutting

If the corners of the walls do not correspond to the standard parameters, then stencils can be used. For this, strips of thin cardboard or thick paper are used, from which strips are cut that correspond in thickness to the selected plinth. They are applied to the corner joint and fixed there, then the unnecessary part of them is cut off using a clerical knife. You need to cut perpendicular to the intersection of the walls, so that in the end you can get two absolutely identical parts of the same corner. The template is used in case of a mismatch between the wall corner and the standard. Cardboard with a thin structure or thick paper take part in the creation. Cut the strips to a thickness suitable for the selected skirting board. The cut piece should be applied so that the unnecessary part is cut off with a clerical knife.

Cutting skirting boards with a miter box

For the correct trimming of the plinth, a special device was invented, which was called the miter box. It is a small block with a notch for the skirting board and with gaps located at different angles. for the cutting tool.

With the help of a miter box, you can get neat and even cuts. The plinth is fixed inside the product, then the angle and direction of cut required in a particular case is selected.

On a note! If it is necessary to form a beautiful angle using a miter box, then one piece of the plinth is cut at one angle, and the second. in a mirror image.

We make a miter box with our own hands

When working with a miter box, it is important to ensure that the edges of the skirting board protrude a short distance beyond the edges of the selected slot. If the trimming tool is wider than the skirting board itself, it is recommended to securely fix the product inside the miter box before trimming. Otherwise, the plinth may move inside, the cut angle will constantly change, because of which it (cut) will turn out to be incorrect and incorrect.

Making cuts for joining skirting boards using a miter box

Important! The pressure on the skirting board should be moderate when cutting. Otherwise, it may break.

Cutting with a rotary miter box

How to cut a skirting board during installation.

Floor skirting boards in any living space. it is an important decorative element. Its advantage lies in preserving the proper appearance of the walls, hiding defects, as well as creating a visual border of the room space in an apartment, house, in the country. A well-cut skirting board will create a contrast with the entire environment. Therefore, it is important to know how to cut the skirting board during installation.