How to cut a tile at home

How to cut a tile without a tile cutter: a few simple ways

Not every home craftsman has in his arsenal of expensive professional devices. But sometimes when laying out small tiled surfaces, there is a problem of how to cut tiles without a tile cutter, which can cause certain difficulties. In such a situation, use a variety of available technology, following the recommended sequence of actions. The material is preliminarily soaked in cool water for 40-45 minutes.

When working with ceramic tiles, you need to perform a variety of types of cuts.

• The material is usually cut in a straight line. It is taken into account that if up to the side edges remains less than 20 mm, then this kind of cut is considered a shaped.
• It is also sometimes necessary to cut a round hole of a certain diameter in the tile.
• Making, if necessary, shaped notches.
• For obtaining mosaic, small-sized elements prefer the method of crushing the ceramic tiles into individual pieces. In this situation, lay the material in a dense bag and use a heavy sledgehammer to break it into the necessary fragments.

Cutting tiles with an angle grinder

Most often, the question of what to cut tiles for the floor without tile cutter, solve with such a universal convenient tool in the work, as an angle grinder, which allows you to perform a variety of dimensions and configuration of the line. smooth curved, complex shaped, clearly delineated straight.

For the tile-cutting operation, it is necessary to prepare:

• Angle grinder, which is more commonly called an angle grinder;
• Cutting wheel, oriented for work on hard stone products (you can take the diamond variety);
• A vice, a portable clamp, or some other simple form of clamp to hold the tile being cut securely in place;
• A compact vacuum cleaner to remove dust;
• Safety glasses;
• gloves;
• Special tight clothing with long sleeves;
• a respirator or cotton gauze bandage is recommended.

After determining the necessary dimensions, conducts a precise marking of the tiles. The cutting trimmer line should be applied to the face plane, using a sharp tool for scratching. A construction marker can be used. But it is necessary to take into account that in the process of work, when removing a large amount of dust, the ink line for the trimmer is quickly erased.

If small cuts are made that are close to the edges of the tile, the material is placed on a flat countertop. It is possible to work on the floor. Put a piece of plywood on the bottom to preserve the integrity of the pavement.

Cut through the tiled surface first, deepening a few millimeters. Usually it is sufficient to hold the tile by yourself during this operation, or you can call for help from an assistant. If you perform shaped cuts, then before sawing the tile without a tile cutter, the material is securely attached to the countertop with a clamp. If possible, fix it in a vice. For safety, under the sponges are put pieces of cardboard or cloth.

• Go over the markings several times, deepening during each pass at about 3 mm. Such actions are performed until the necessary tile fragment is cut off completely.
• If you cut small pieces, about 20 mm long, then cut through the entire thickness of the material at once.
• When making complex edge cuts or curved lines, it is advisable to mark on both sides. First make an incision of 2,5-3 mm along the front side. After that you turn the material over and pass it from the back to the identical depth. Repeat several times. This method practically does not damage the face side of tiles.

What podrezit (sharpen) tiles at an angle of 45 degrees?

Everyone calls this action differently: file, sharpen, trim, bush, Kremlin angle. the meaning is the same.

For qualitative trimming of tile ends under 45 degrees you will need an electric tile cutter (tile cutting machine) or, as a last resort, an angle grinder (angle grinder) with a tile disk.

The easiest way. the angle grinder

It is more difficult to achieve a quality result with an angle grinder, but in principle, it is also possible. This is the easiest way to grind a tile corner of 45 degrees with your own hands at home.

The process of boring and sanding porcelain tiles in the video below.

First of all you need to have a good diamond tile disk.

Place the tile on a rib (prpendicular to the one being trimmed) and grind at a 45 degree angle to the back of it (clay).

If you get a little rough, then large roughness can be passed again disk, and in order to get a cleaner and smoother edge can be used here (pictured below) sanding pad with sandpaper or diamond “turtles.

Sanding discs on the velcro, wiped. remove and attach a new one. The base itself with Velcro is screwed onto the thread of an angle grinder. Diamond bits have a much longer life, but they cost a lot more. If you install tiles all the time, it makes sense to use diamond turtles. If you’re doing your first and last repair in your life, you can do with an emery wheel.

When working with such a thing you need an angle grinder with speed controllable (speed to a minimum)!) otherwise the edge of the tile will melt and burn rather than grind.

Electric tile cutter

Electric tile cutter, or as it is also called by tilers. wet cutter. It has a water cooling disk, and the same water dampens all possible dust. The tile cutter cuts along one precise fixed trajectory and minimizes such a human factor as shaking hands, etc.п.

The tile cutter has two operating positions. a straight cut and a cut at an angle of 45 ° (actually you can set any angle from 0 to 45 °, but this is most often no point).

How to properly trim a tile at 45 degrees?

In order for the corner of the two tiles looked beautifully, in trimming the tile must not reach the glaze (0.5-1mm). That is, only the clay is cut. If you go over the glaze (the front part of the tile), it will be “torn” and scratchy. It will immediately catch the eye, it is not beautiful.

Such a problem we faced at trimming wavy tiles. But about that later.

Surely many of you have seen such “artwork”, but most often everyone thinks that it should be so. And yet the tiler with twenty years of experience assures you that it can’t be any other way.

Even if you need to cut the corner of the tile not from the “factory” edge, and you have to cut the glaze, there’s still a way to do it beautifully.

First, to do this, you must first cut the tile evenly (to the right size), and then already, again, not reaching the glaze, trim it at 45°. This cut will be much cleaner and prettier.

You can also process the edge of the glaze with a fine sandpaper, from this it will be even smoother.

Secondly, you can still cut the corner of the beautiful edge (factory end), and trimmed the opposite edge of the machined sandpaper and hide the other side. This will be less conspicuous.

This, for example, is what we once did when tiling a toilet installation. Because a beautiful corner is more important than the bottom seam. All the more so because it turned out to be very neat too, and if you don’t know that it is trimmed, you’ll never pay attention to it.

Ways to cut a tile

The following methods are mainly suitable for cutting tiles at home. But also applicable or limited to other types of tile. You can cut tiles without a tile cutter in the following ways:

Angle grinder (angle grinder)

Generally speaking, this is a versatile tool. As in the past masters with one axe could cut down a house, so now with one angle grinder can cut out anything. The author has witnessed how to cut an even circular hole with a diameter of 5 cm.

Note! The method is suitable for straight, shaped views and, with minimal tooling skills, for curved lines of any configuration.

• angle grinder. Any power and any kind;
• Cutting wheel (stone or diamond);
• Protective helmet or goggles (mandatory);
• Protective fully enclosed suit and gloves (recommended);
• Respirator (recommended);
• Clamp. Optional in some cases (clamp or vice).

Pre-mark the tiles, preferably with scratching the line with any sharp instrument. In the extreme case it is allowed to draw a line with a construction marker. A lot of dust is generated and the marked lines can be rubbed off when removing it.

Small straight cuts along the edges of the tile can be made by laying the tile on a flat surface on a table or the floor. First several millimetres are cut into the surface. With this cutting method, the own weight of the tile and the friction force are sufficient to hold the product in place. For deeper cuts, it is possible to step on the edge or hold a helper. With shaped cuts, it is better to attach the product with a clamp to the table top or fix it in a vise, previously placing under the jaws pieces of cardboard or a thick cloth.

Advice! Place a piece of plywood under the product to avoid damaging the surface of the table or floor.

• On the outer edge of the marker, walk several times along the entire length. Up to 3 mm deepened in one pass. Repeat the operation until the result is achieved;
• For small sections, up to 2 cm in length, at once for the entire thickness;
• The line is marked on both sides. A superficial cut (up to 3 mm) is made on the face side. Then cut backwards (up to 3 mm per pass) until the target is reached. This way you can avoid accidental damage to the face with a cutting tool.

Recommended for difficult cuts: on edges or curved surfaces. The fact is that with this method there is a lot of dust, cutting blade consumption, time and labor costs. Normal straight trimmer fishing line can be cut in much simpler ways.

Electric jigsaw

If you do not have a tile cutter or angle grinder, a jigsaw may be available. A tool underestimated by many!

Note! A manual jigsaw with a stone saw can be used in the same way. But the cutting speed will be an order of magnitude slower.

• Electric jigsaw. Any power requirement;
• Stone saw;
• Safety glasses (recommended).

It can be sawn in the usual way. Sawing too rounded cuts is difficult, the saw jams. Not thick (wall) tiles can be sawn well. It is very difficult to cut porcelain floortiles in this way. Soaking the material beforehand is suggested for a slight easing.

Recommended when it is necessary to cut curved sections with large radii of curvature.

The glass cutter or any pointed instrument

Only tile can be cut with this method. And only in a straight line. Another restriction. the pieces must not be less than 2 cm wide.

• The glass cutter. Instead of the glass cutter, any tool with a pointed cutting edge can be used. The cutting tool should preferably be made of hard materials: diamond, bobedite, etc.д. As examples of cutting tools: drills, lance drills, utility knife, etc;
• Metal ruler or any straight metal rail. In the extreme case of any material. But then you need to be very careful when scratching the trimmer line of the cut, because it is possible to cut through the ruler and the scratch will go sideways on the tile.

In order to get a sharp cut without any splinters and deviations the scratch has to be applied accurately. It is enough to scratch the upper, glossy layer.

Tip! Pay attention to the beginning and the end of the scratch when applying the risk. Often the scratch is not deep enough at the beginning and at the end. This is due to lack of pressure and psychology. At the beginning we only try it on and the pressure is loose. At the very end, there is acceleration and the risk is “blurred”. This can cause the break in these areas to go sideways.

When making a risk with a knife, several passes are made to get a deep scratch.

Scratch penetration depends on the hardness and sharpness of the tool used. If the tool is hard enough and sharpened (a glass cutter with a sharp roller, a lance-shaped sharpened pobedite drill bit, etc.).д.), one pass with good effort is enough. If the tool is blunt or made of soft material (utility knife), several passes are required. Eventually the groove should deepen below the glossy layer.

• At an even sharp corner. Grasp the tile with both hands on opposite sides of the risk. Strike sharply from a distance of 5 cm.10 cm against the corner from the back side of the piece. Aim well beforehand, so that the impact hits the breaking point as accurately as possible. The angle can be anything, the main thing that it must be sharp and hard (metal angle, wooden bar). It is desirable for convenience, that the corner should rise above the surface by about 10 centimeters. Otherwise there is a probability of striking the surface with your hand, the strike will go sideways and the tile will break not along the line;
• On a hard bar. Lay the tile on a long hard bar with its back side aligned in the place of the groove. Then press sharply on both sides with both hands. The rod can be anything. flat, about 8 to 15 mm in diameter (a drill bit, a round pencil, etc).д.). Preferably, the length should be not less than 2/3 of the breaking length. You can break out parts, but not through the entire length of the tile;
• Between the clamps. The method is suitable both for breaking through the whole tile and for breaking out large pieces. Approaches are different, but the essence is the same. It is required to fix the product between the two clamps at the breaking point. It can be two bars or thick plywood. You can make a small machine: two sheets of plywood fastened at one end with self-tapping screws, the tile is placed inside by pushing them apart with force. The main thing is to ensure that there are even, sharp edges and the accuracy of placing the material on the line for the trimmer risks. After installation, additionally clamp the structure with your own weight and push sharply on the protruding edge.

How to cut with a handheld tile cutter?

This tool is only used to make light, straight cuts. With it you can cut a tile either evenly or diagonally. The direction does not matter. This equipment is very easy to use. At the same time, before cutting tiles with a tile cutter, it is necessary to have a general idea about its structure. The tool has a base plate on which special tubular runners are mounted. A carriage with a hard-metal roller slides over them. After marking, the tiles are laid on this substrate as required.

Here are the basic recommendations for using this tool:

• The roller must be applied to the tile and a special handle must be used to accurately make the cut. In this case you only need to make one cut. It is not necessary to cut through the same place two or three times. The result will be pitiable. the material will not break at all as it is necessary. This is also the reason why you must carefully check the sharpness of your cutter. On specialized professional models, it is removable, so if necessary, a blunt roller can be easily replaced.
• It is worth noting that in order to get a quality tile when working with such a tool, you must also be able to break the material competently. On the base of the equipment in the course of the cut is a small bump that lifts the edge of the ceramic product clearly above the cut and then releases its ends. This is the reason why this ridge along with the slit on the tile acts as a guide for breaking. The workpiece is also broken by a movable T-shaped heel located in front of the roller. This heel must be set exactly in the middle of the cut, so that when the lever is pressed, it presses on the blade. Also this tile cutter can cut diagonally.

How to cut tiles with an electric tile cutter?

If you plan to work with very hard and large format tiles, it is best to use professional equipment. an electric tile cutter. To work with such equipment requires certain professional skills and abilities. In particular, since the cutting process is quite complex and time-consuming. However, still, if you are interested in what to cut ceramic tiles as quickly and accurately as possible, even with very large volumes, then an electric tool is the best choice. Such equipment is quite expensive, but pays for itself with repeated use and can serve for several decades. By design, the electric tile cutter is almost identical to a modern circular saw. The main differences are in the discs used and the presence of water trays.

Another feature of these machines is the ability to make neat tilted cuts. This is very useful when tiling outside corners. In this case, there is no need for aluminum or plastic corners at all. The product, which is docked in the corner with an undercut of 45 degrees, looks very interesting.

We present you a brief instruction manual:

• Pour water into the tray so that it overlaps the disk by 2-3 centimeters;
• We measure a part of a tile that needs to be cut and put it on the machine;
• then we press our blade to the machine and slowly bring it to the disk. It is not advisable to press down hard on the disc, as it may stop;
• Now we have to make the cut on the second line. To do this, gently lift the tile and do the same procedure.
• The electric jigsaw works quite quickly, the quality of the cut is quite satisfactory. The speed and accuracy depends on the grit size of the saw. the higher it is, the higher speed is, but the worse is the quality of cut. A fine-grained jigsaw for ceramic tile cuts cleaner, but slower.
• Usually an electric jigsaw is used, but for particularly demanding moments, where a cut of a very complex shape and high quality is required, a manual tool is used. Its speed is many times slower, but the quality is much higher.
• It should be taken into account that you can work with any jigsaw only with wall tile of low density. The jigsaw is not good for porcelain tile.

So, how to saw tiles with a jigsaw?

• Prepare the workplace. an even table, on which the majority of the tiles to be cut will be placed, a clamp for fixing the tiles, a marker or a pencil for marking.
• Soak the tiles in cold water for 1-2 hours.
• Start cutting ceramic tiles at a low rpm, applying medium pressure.

When working with a manual jigsaw, the technology remains the same as with the electric jigsaw, but the cutting is done in manual mode, with a special saw with a diamond coating and is much longer. Generally speaking, it takes more time to work with the jigsaw, but it produces excellent results.

• A trimmer line is drawn across the face of the tile with a nail and a metal ruler (rail).
• The cut should be smooth and as deep as possible.
• You can make another 1 cut from the back side of the tile, but it is necessary to observe the maximum accuracy.
• Tiles are accurately broken along the cutting line in the usual way.
• often than not, the line for the trimmer cut needs to be cleaned and sanded.

As you can see, there is nothing complicated, but it is still better not to abuse this method. It is rather tedious, and the quality of the cut is not very good, it takes a lot of effort to finish.

Ways to cut a tile

There are special devices for cutting tiles. However, you can cut tiles at home without a tile cutter. You can use the devices for one-time work, others will cope with tiling on an industrial scale. I also differentiate the devices depending on the types of tiles.

Cutting ceramic with an angle grinder

This angle grinder can cut both ceramic and tile at home. The tool in skilled hands will make not only a straight line for the trimmer, but also a shaped one. For the beginning it is necessary to prepare:

• Tile.
• Angle grinder or angle grinder.
• Cutting and sanding discs.
• Protective equipment. A mask or glasses are indispensable, and a respirator and overalls are worn as necessary.
• Vise or clamps.

Use a sharpened object to make a preliminary marking. You can use an indelible marker. Lines drawn with a simple felt-tip pen will rub off on the mirror surface.

On the table where you plan to cut the tiles, you need to lay a piece of plywood or other material so as not to spoil the surface.

For shallow cuts, the tile does not need to be held back. Its weight and the friction force of the underside with the table are enough to keep it in place. At a more serious recess you may need a partner’s help if you can’t fix the tile with your foot.

Curvilinear cuts will require fixing the tile in a vice, and it must be covered on both sides with a soft cloth or cardboard to avoid scratches.

In order to make a quality fit, it is necessary to:

• Deepening should be done gradually, cutting 2-3 mm in depth at a time.
• Carry out small cuts to the full thickness at once.
• To prevent the disc from accidentally coming into contact with the surface, it is advisable to make a marking on both sides. Then make one solid cut on the glossy part, and finish with the inner.

It is better to make shaped edges with an angle grinder, and straight edges with another, simpler tool. This will avoid the cost of buying diamond discs, as well as the dust that rises when working this way.

Cutting with an electric jigsaw

If there is no angle grinder at hand, another electric tool can be close by. When speed is not important, you can also use an ordinary jigsaw with a stone blade. Cutting tiles with such a device does not differ from the processing of any other material. Only a special saw and a preliminary soaking of the tile is required.

The jigsaw is not effective for thick tiles. It is suitable for wall coverings and cutting out pieces with a large radius of curvature.

A glass cutter or any pointed object

This is another way to cut a tile without a tile cutter. Such a tool works only on tiles and in a straight line. There is also a limit on the width of the cut. at least 20 millimeters. You will need the tool itself or a similar device. Diamond or hammer drill bits are used for this. Sometimes a good utility knife can be used.

The ruler, which will make the cut, it is necessary to have a metal one, as the wooden one can be spoiled if the knife will be torn from the cutting line.

The cut should be made slowly, gently. Particular attention must be paid to the initial and final pressure of the tool. It is usually insufficient at these moments. If you do not cut through the edges well, the break in these places will be uneven.

To cut ceramic tiles at home, you can use improvised means. It is necessary to spend with a drill or a knife several times along the trajectory, until the upper layer of the tile is cut through. The number of starts depends on the hardness of the tool.

To split a notched tile can be done in several ways:

Taking the tile from both sides along both edges of the cut, clearly, from a distance of 10-15 centimeters hit the edge of the table. The corner must be straight and firm. The blow should be made carefully, without hitting the surface with the palms of your hands.
• You can put a flat rod under the entire length of the tile in the line of the notch. It should protrude over the edges by a few centimeters. It is necessary to press sharply on both edges with both hands. If the length of a piece of tile is long, make this operation in several passes.
• For breaking in clamping devices, the tile should be wrapped in cardboard and clamped between the jaws along the break line. You can make a home-made clamp from two metal angles or wooden bars, fastened with bolts or pins.

Hole drilling technique

The process begins with the selection of drills or bits of any diameter. Any drilling tool will do, electric or manual. For drills, it is desirable to have a speed control. It is important for safety of cutting tools, because the high speed quickly shrinks tips. Also in this case there is an increased probability of chipping the enamel.

Holes are made using special sharp-angled drill bits. But they are expensive. But it is possible to drill a surface of any hardness, and the life of such a tool is long. Usage of inexpensive lance-shaped tile drill bits is suitable for periodic, small amount of work. One tool, when used on tiles, is enough for two dozen holes. Pobedite drills are recommended for use only as a last resort.

For the production of large round openings, you can use a crown molding or ballerina.

Hand-held tile cutter

This tool allows you to cut tiles in a straight line or diagonally with a cutting width of 5 millimeters or more. It can be used to cut floor tiles and porcelain tiles. Its construction consists of a base and a carriage with a diamond blade. a wheel that slides on the slides. It has a larger diameter for deeper cuts than the glass cutter. The knife can be replaced as it wears. When selecting a tool, it is advisable to purchase a mechanism with bearings to ensure smooth sliding of the cutting mechanism.

For breaking off the notched bar, a flat metal band is attached to the base at the edge and a small T-shaped lever behind the cut-off blade. It is the one that presses the tile after the cut.

The tile cut begins with the alignment of the material on the base according to a marked line. Then it is firmly fixed. The carriage is driven by hand, making a single cut. Then, the tile is split into pieces by pushing on the handle. This method sometimes results in small chips, which are masked with grout.

Tile types and cutting features

Glazed tiles are the most common. Its cutting is very similar to that on glass. Mark the grooves on the front side. If at hand are only pliers or a weak tile cutter, then facilitate the cutting of thick floor ceramics can be used with an angle grinder. This is done by duplicating the cutting line for the trimmer from the front to the back. Carefully make a furrow with an angle grinder about half the thickness of the tile. After that, it’s already much easier to break it.

The best way to break it is to let the tile fall along the line of the notch on a flat surface, a corner of a tabletop or a metal corner piece. Look at the tile cutter as an example and see how the cut line support is implemented on it. There is a small flat overhang along the entire length and a slightly beveled surface edge on the sides of the overhang.

If you need to cut porcelain tile or any textured tile, there are very few options. For such a purpose, you can only use tools with a diamond disk, which cuts through the entire thickness of the tile.

Cutting with an angle grinder or a machine tool is always performed on an even surface without tearing off the tile from it. Otherwise you could easily chip the material in a situation where the cutting blade gets stuck in the cut.

Cutting oblique lines and shaped edges

The shape of the cutout is marked out on the slab in advance. It can be a corner or even a rounded edge to install tiles at a wall projection or pipe exit. After that, either use an electric grinder to carefully and piecemeal cut out all the unnecessary material, or use tongs.

For the second option, you should carefully spend a cutting wheel on the line of the cut. After that, using pliers or pliers, literally chew off a piece of tile until they get to the edge of the bounding line. For the design of an even edge you can use rough sandpaper or nadfil.

Even if the shape cutting is performed on an electric machine, sometimes it is necessary to finish the line for the trimmer with pliers.

Safety when cutting tiles for floors and walls

Every master knows that when laying tile products can not do without cutting them. Performing this rather complicated process it is necessary to adhere to certain safety rules.

To avoid damage by tile particles, which can fly in different directions, the master must be protected by special clothing, technical goggles, work gloves, it is also desirable to use earplugs, because the process is relatively noisy.

All working tools should be in good condition, especially pay attention to electrical appliances, exclude the possibility of water. It is important to work in a well-ventilated room.

How to cut a tile with his own hands

Let’s consider options for cutting tiles with their own hands at home. There are many ways, but the main one is a tile cutter.

But if there is no such a tool, it can be replaced, for example, with a glass cutter, angle grinder with a diamond disc, electric jigsaw or special tongs-glass cutters.

Let’s look at each in more detail to understand their convenience and availability.

Manual tile cutter

The first option. a manual tile cutter. Getting to work, you must prepare the device: to make sure there is no damage, to check the smooth running of the cutting roller (if necessary. lubricate with machine oil).

Before using a handheld tile cutter, you need to properly prepare it and make sure that there is no damage to the device.

It is also important to fix the tile well, using the special grips provided on the device, if they are not. the tile should be fixed with the left hand and the cut should be made with the right hand.

For a more accurate result, you need to use a ruler and marker to draw a line for the trimmer. All prepared. you can get to work. Firstly, you need to lift the handle of the tile cutter so that the cutting wheel touches the face of the tile.

Make the cut with moderate pressure. Pay attention that too little pressure will not give you the desired result and the cut can be uneven, too strong. will leave chips in the cut line on the front side, which will significantly affect the appearance and will require additional processing.

IMPORTANT! The cut to do in one longitudinal motion, this will eliminate unnecessary grooves, uneven break and cracks.

After that, we put the tile on a flat surface, lifting one edge that is farther away from the cut line, and make the cut with a sharp even pressure.

You can use a nail or a bar. To do this, put a nail under the tile (can be replaced by a wooden bar) and with equal pressure to the sides to make a break. Sand down any irregularities with sandpaper.

Also the best option when cutting tiles will be the glass cutter. The necessary tools: a glass cutter with a thin disc, a marker, a metal ruler, a nail, and sandpaper. It should be noted that this type of cutting is not the most popular and convenient, but for a small amount of work it will do in principle. Getting started with the procedure is important to make sure that the work surface is flat and solid.

The tile should be put upside down, using the ruler and marker to cross out the intended place of the cut, without removing the ruler cut the tile with the glass cutter, spending a few times. Pay attention that it is necessary to carry out accurately along one line and with the same pressure.

The groove should be single and even. The pressure must be equal along the cut line, so the edges will end up flat. Make the rupture as described in the method above. Using sandpaper to grind the seams of the product to give an aesthetic finish to the product.

It should be noted that this option is suitable for wall tiles no thicker than 6 mm.

IMPORTANT! Follow the technology as precisely as possible, because breaking it will lead to sloppy edges and chips.

Electric plate cutter (water saw)

The next option will have to those who often work with tiles, because the device is quite expensive. an electric tile cutter (or a machine for trimming tiles, or a water saw).

The most effective, as trimming is carried out in a straight line and the groove is obtained by optimal depth, the break is made with a special device that eliminates chips and cracks, this way you can trim a large number of tiles.

This method will be more simple and convenient, but the thing is more expensive compared to the others given in the article.

We mark out the tile in the same way (ruler and marker), put it inside the device and, using the cutter with the same pressure, run the line for the trimmer, then using the pressure provided by the device, make a break.

Such a device allows you to cut both thinner wall tiles and thicker floor tiles. In electric glass cutter provides water cooling, so the disc does not overheat, it also contributes to a relatively dust-free cutting process.

angle grinder with diamond disc

Those who do not want to bother with manual cutting tiles, but do not have the opportunity to buy a professional machine, you can use an ordinary angle grinder with a diamond disc. This method is very dusty and a respirator is recommended.

When cutting tiles with an angle grinder, do not forget to use a respirator to protect your respiratory system from dust.

It should be noted that this method will not be possible for everyone, because the angle grinder must be held firmly and confidently in the hands to make a straight cut. We mark with a marker or a pencil tile, put it on a wooden surface (which is not sorry, because the cut will be through and then have to throw away), cut along the planned line, gradually deepening.