How to cut a tile with a tile cutter by hand secrets

How to cut tiles

The principle of operation of the tile cutter is simple and similar in action to an ordinary glass cutter. The pressed diamond roller, when driving, cuts a furrow along which a fracture is subsequently made. The difference is in the improved design. the roller guides, strong fasteners and the presence of a lever make it possible to cut the groove in the glaze tile with force. To properly cut tiles with a manual tile cutter, you need to consider all the steps in detail.

The secret is to make the tile pliable, to avoid splitting and crumbling, 1.5-2 hours before cutting it is covered with a wet cloth or soaked in water.

Tile cutter-tongs

For small volumes of work, it is convenient to cut the tile with a tile cutter-tongs. It is an inexpensive, practical tool. It looks like a large wire cutter, on the side there is a sharpened roller, which makes a furrow along the marked mowing line. The sharp part of the jaws of the forceps is intended for installation on the furrow of the face part, the flat foot is at the bottom. Then they gently press on the handles, which ensures an even break. It is advisable to keep the die low above the table so as not to break it if accidentally dropped. You can bite off thin strips with such tongs.

How to use a tile cutter: everything about cutting principles

Repair in a private house or apartment is not complete without facing walls or floors with ceramic tiles or tiles. You can perform the work yourself, without the involvement of professional repairmen, since the services of the corresponding firms are regarded quite expensive. To use the tile cutter correctly, you need to know how to lay the tiles correctly.

Roller tile cutter

The instructions for use of the manual mechanical device provide the following procedure to cut the tile with the tile cutter.

  • Place the insert face up on the bed with the diamond cutter positioned exactly over the marked cut line.
  • To prevent displacement, the tile is abutted against the stop available in the bed.
  • If it is necessary to cut a small strip, it is necessary to put a stop under the main overhanging part for stability of the same height as the bed.
  • Then, holding the lever, the carriage is put into working condition, the support legs are folded back, the diamond cutter is placed on the marked line of the cut.
  • Pressing the lever, roll the roll on the marked mowing line. You cannot rush and make sudden movements, the cutter must be smooth, with uniform pressure.

In case of light pressure and a shallow furrow, do not re-pass with the cutter. When the cut is repeated, the edges begin to crumble, resulting in a sloppy cut.

When working, it should be borne in mind that a manual tile cutter cannot cut strips less than 1 cm wide. If necessary, break off the edge with nippers. The curly edge is made in the same way. For the first time cutting tiles, it is better to practice on defective or broken tiles. There is a design of a mechanical bearing tile cutter that is designed for plates with a thickness of more than 16 mm.

Preparing the tool for work

Two types of tile cutters are used for cutting. electrical and mechanical. Mains powered models are suitable for large scale construction. Mechanical models are sufficient for home repairs. It should only be remembered that their use requires skill, the use of physical force.

The preparatory process of the tool for work consists of the following steps.

  • Inspect for damage or distortion to the cutter wheel and should not be jagged. Otherwise, the element will need to be replaced with a new part.
  • Oil lubrication of the moving carriage to avoid movement problems.
  • Cleaning the body of the device, guides, bed surface.
  • Tightening of all fasteners.
  • If the model has clamps for fixation, you need to take care of the immobility of the tool.

Electric tile cutter

Working on an electric machine is advisable with a professional scope of work, since the equipment is expensive. The principle of operation is based on cutting with a diamond wheel, a stream of water is automatically supplied to the cut point, which cools the disc and washes away the formed dust. Precisely calibrated movements of the diamond blade give a perfectly even cutting line, which allows you to join the tiles at the outer corners without decorating overhead strips. There are both portable lightweight models and stationary floor machines.

Safety engineering

When working with any tool, you must comply with the general safety requirements. In this case, the requirements are similar:

  • work is carried out in goggles to exclude dust and possible small fragments from getting into the eyes;
  • to avoid cuts or injuries, protect hands with cloth gloves.

complex requirements are put forward when working with an electric tile cutter.

  • Before work, carefully check the power tool for damage.
  • The diamond disc must be flat, sharp, free of nicks and chips.
  • Pay attention to smooth rotation, absence of backlash, availability of water supply to the disc.
  • The appearance of sparks, uncharacteristic noise during operation is unacceptable.

It is not difficult to work with a tile cutter, a mechanical tool is enough for laying a small area. The principles of cutting are easily learned even by novice home craftsmen. Professionals will need a powerful, reliable power tool with enhanced capabilities.

How to properly cut tiles with a tile cutter

Experienced craftsmen, before cutting the tiles with a manual tile cutter, recommend holding the tiles in warm water for a while. It will become slightly softer, which will reduce the likelihood of cracks and chips. To reduce friction and improve cut quality, it is advised to drip machine oil directly onto the line or the cutter wheel.

How to use a manual tile cutter correctly

To use the manual tile cutter correctly, you should be guided by the following technology:

  • On the face of the tile, use a marker or felt-tip pen to apply a line of marking.
  • Fix the material with special clamps, while the line should be located exactly under the cutting wheel.
  • Place the cutting element at the beginning of the markup and press it lightly.
  • Grasp the handle and gently move the carriage away from you along the cutting line. The pressure must be strong enough to cut the glaze. With great force, it is possible to break the tiles or damage the glazed layer at the cut. Insufficient pressure will not allow breaking the hard surface and then breaking the tile.
  • Move the handle to the middle, lower the lever (if included), then press it or hit it sharply. In the absence of a lever, the tiles are placed on the edge of the table along the mowing line of the cut and broken by pressing on the part protruding from the edge.

If everything was done correctly, the tile should break neatly exactly along the mowing line of the cut. Some models are equipped with a built-in ruler and a rotary base for cutting tiles at an angle of 45 degrees. Read more at

How to properly cut tiles with different tile cutters?

Every craftsman should know how to cut a tile with a tile cutter so as not to spoil a rather expensive material. Any facing work with ceramic tiles is not complete without cutting, when you need to get fragments of the required size and shape. For a good appearance, it is necessary that the cut is even and neat, and after grouting, a sharp uneven edge does not stick out.

Manual tile cutter device

The device of manual tile cutters is the same, there are only a few differences regarding functionality. The following working parts are distinguished:

  • base, which serves as a platform for the location of all working elements;
  • tubular guides along which the carriage with a cutting wheel moves;
  • carriage. in addition to the cutting roller, it is equipped with a special concave foot for breaking off the cut part of the tile;
  • cutting element. a carbide roller rotating on an axis;
  • handle with which the carriage moves.

tile, cutter, hand, secrets

Advantages and disadvantages of manual tile cutters

Like any other tool, a manual tile cutter has positive and negative qualities that you should definitely consider when choosing a tile cutting attachment.

Among the advantages are the following characteristics:

  • independence from electrical networks;
  • the ability to use at any temperature and humidity;
  • compactness;
  • light weight;
  • low cost.

The disadvantages include the following qualities:

Cutting tiles without power tools

  • does not cope with a large amount of work;
  • does not allow cutting a strip of tile less than 1 cm;
  • cuts particularly hard material with difficulty.

How to use the tile cutter

For a small number of tile cuts, you can use a tongs cutter. They are useful for making rounded cuts and fine adjusting tiles when laying tiles. This device is similar to a pair of pliers. The cutting roller is located on the holding jaws.

Cutting is carried out as follows:

  • markings are applied to the glazed surface of the tile;
  • along the mowing line, in one motion, an incision is made with a cutting disc from the far edge towards you;
  • the pliers are placed with the tool paws up (on the glaze), the cut line should be in the middle (between the side surfaces of the paws);
  • gently press the handles, breaking off an unnecessary fragment.

Safety engineering

You need to know how to safely carry out work on cutting tiles with your own hands, how to avoid possible injuries. There are a number of requirements that must be met:

  • Inspect the tile cutter for operability and damage.
  • Check carriage travel. It should move smoothly, without jerking.
  • The guides must be even and smooth, without damage.
  • The cutting blade must have a level surface, free from burrs and dents. It should rotate freely on the axis without creaking or getting stuck.

For safety reasons, use protective plastic goggles and fabric gloves.

What is a tile cutter

Outwardly, this tool looks like a pliers on a platform. Indeed, it consists of:

  • Foundations;
  • Guides with supports;
  • Carriages with a handle;
  • Breaking feet;
  • Cutting roller.

Functionally, the tile cutter resembles a glass cutter, with the only difference that the roller made of hard alloy is much larger here. it is understandable, you have to cut a different material. And just like glass, the roller scratches the tile in that part of it where there should be a break.

Some secrets

  • The wheel that is used for scribbling must be firmly attached to its place with a small bolt. Before starting work, it is necessary to check the reliability of the roller fastening, otherwise the tiles will be broken uneven.
  • Another tip on how to properly cut tiles with a tile cutter: use oil in your work. It should be applied before starting on the wheel and guide frame, but very little, literally a few drops.
  • When choosing a tile cutter, stop the choice on the one in which the carriage is equipped with bearings. Let it cost a little more than a design in which the carriage is put directly on the guides, but on the other hand, the stroke of such a tool is light and soft, and there is no backlash, and the resource is much longer.
  • Keep in mind that the minimum part width that can be cut with a manual tile cutter is 5-6 mm. Therefore, just in case, experienced craftsmen have tile cutters in their arsenal.

Source: http://stroihata.ru/kak-pravilno-rezat-plitku-plitkorezom.html

Principle of operation

It is not difficult for craftsmen to quickly and evenly cut the tiles. For this you need:

  • Using a ruler, mark the break with a felt-tip pen.
  • Place the tiles on the base so that the cutter wheel aligns with the drawn line.
  • While holding the tile with one hand, lift the handle with the other so that the roller touches the tile at the beginning of the future break, and pull the handle towards you with slight pressure. One pass is usually sufficient for a quality cut.
  • When scratching, the wing-foot does not press on the tile. the roller interferes, but when the cut is over, you need to install the bar, which is on the rod with the cutting roller, in the lower part of the base of the tile so that the pressure falls somewhere on the lower third of the tile and, slightly by pressing, remove two even parts from the tool.

How to properly cut tiles with a manual tile cutter

Initial task for cutting

To me, in this case, doing repairs in the bathroom. for laying the tiles on the floor, it was necessary to shorten a little. cut the tiles by 3.5 cm on one side.

Making measurements for cutting tiles.

If we look closely at the instrument, we will see. a special protrusion (swing axis) runs in the center of the tile cutter, serves to break tiles along the mowing line of the cut. There is also a handle that can move along the tubular guides along the horizontal plane. A carriage with a wheel-cutter and a breaking unit (legs) for breaking tiles is attached to it. Finally, there is a ruler with a stop and a backing on the working base, which prevents tiles from sliding during the cutting process.

How to cut tiles with a manual tile cutter

The manual tile cutter is one of the simplest and most convenient devices for cutting tiles into multiple pieces. Its price is quite low (from 2000 rubles), and the savings are significant. Its only drawback is that they cannot cut porcelain stoneware. A manual tile cutter is used to cut ceramic wall tiles.

It is not difficult to use it. The tile is secured and carefully scored with the wheel along the mowing line of the break. After that, the lever is lowered, and the tile is broken into two parts. But first you need to drop a little oil on the guide frame and on the wheel with which the risk is applied. Before starting work, make sure that the cutter wheel is secured correctly and does not move from side to side. If it is not secured correctly, then the notch may turn out to be crooked and the tile will be damaged.

Depending on the structure of the tiles, even 5-6 mm can be cut with a machine. The denser it is, the easier it is to cut it with a tile cutter, hence the more likely it is to cut, if necessary, a thinner strip. If you cannot cut off a narrow strip using a machine, then you can make a notch with it and break off all the excess with pliers. You can also use a glass cutter and a nail instead of a tile cutter. With a glass cutter, a notch is made on the tile, then it is placed with the back side on the nail. the cut line and the nail are combined, and then pressed down with thumbs on both sides of it.

Before cutting the tiles, you must apply the cutting line to the tiles with a felt-tip pen or marker. Then the tiles are laid on the base of the tile cutter, and the cutting line and the wheel for applying the risks must be aligned. Hold the tile in one place with one hand, and a handle with a wheel in the other hand.

The handle must be lifted so that the wheel touches the surface of the upper part of the tile. Then the handle should be started to move towards you. over, it is necessary to press on it lightly. The pressure should be sufficient to apply the risks, the passage with the wheel needs to be done only once. Repeated cutting of the mowing line will result in a poor cut.

To divide the tile into parts, according to the intended risk, “wings” are installed at the beginning of the handle at the level of the lower third of the tile. If you stick them over with adhesive tape, then there will be no traces of them on the tiles. Usually, experts try to hold it in the desired position, while slightly pressing on the handle with the thumb of the left hand, and lightly hit the handle with the palm of the right hand.

If the tiles remain intact, they hit harder. If it still does not crack, then you need to take another and start all over again.

If the tile is in place and the cut edge is visible, the sharp corner can be trimmed. To do this, use sandpaper or a grinding stone. Specialists usually have several types of grinding stone used for different types of tiles. It is possible not to align the edges if this edge is covered by another tile.

Placing tiles on the tile cutter, cutting tiles

The tile is installed on the working base close to the tile cutter’s ruler (one division. 0.5 cm). Since I need to cut off 3.5 cm, the edge of the tile must be attached to the corresponding mark on the ruler.

Preparing tiles for cutting.

5 Ways To Cut Tile. Everything You Need To Know For Your First Tile Project

The handle with the tile cutter carriage must be swiveled away from the ruler. When cutting tiles, the handle with the carriage along the tubular guides returns back to the ruler until it stops.

The principle of cutting tiles with a tile cutter is simple. it is necessary to cut a little in the upper part of the tile, pressing on the handle and moving the carriage along the tubular guides along the cutting line of the cut towards the ruler until it stops. And then make an effort by stepping on the tile with your foot. fixed under the ring, without removing the tile from the tile cutter and holding it with your hands.

the breaking line is cut. Step foot.

The tile will crack clearly along the mowing line of the cut.

An extremely important point. The protrusion of the tile cutter (swing axis) for breaking the tile must be clearly below the cutting line, if the tile slides a little to the side, it will break in the wrong way!

In my case, it was required to draw a horizontal cut of the tile with the same distance on both sides, but if you need to make an oblique cut of the tile, then when placing the tile along the ruler, it is set slightly at an angle. This cut is also possible.

Here is a simple answer to the question of how to cut ceramic tiles with a tile cutter at home.

How to properly cut tiles with a tile cutter?

The smoother the tiles are cut, no matter where to lay them. on the wall or on the floor, the more beautiful the final result will be. Yes, and more practical too. A smooth joint between adjacent tiles, after filling with mortar, will turn into a neat seam that can only be admired. It is clear that laying entire tiles in this regard does not raise any questions, but almost always in the course of work, pieces of tiles are also required. To do this, cut it using:

  • Glass cutter;
  • Manual tile cutter;
  • Electric tile cutter;
  • Angle Grinder.

How to cut tiles with a tile cutter?

  • Glass cutter
  • Manual tile cutter
  • Angle Grinder
  • Electric tile cutter
  • Figured cutting of tiles
  • Output

During the renovation, when all the dirty, rough work is done, it is worth thinking about finishing the floor, walls and ceiling. Many people stop their eyes on tiled cladding. Tiled, like tiled, is one of the oldest, but no less practical coatings. Today, tiles are made from many different materials, such as ceramics, cement, stone and, in some cases, even glass. Any tile, regardless of the material from which it is made, requires special care.

When tiling walls or floors, it is almost impossible to guess with the dimensions of the covered canvas, therefore, fragmentary laying is in great demand to this day.

The peculiarity of the tile is that in the right hands it will become the best choice in the decoration of any room, be it a kitchen, bathroom, toilet or, for example, a garage.

The tile is a very wear-resistant and durable material, however, with figured cutting, there are often cases of splits and cracks, which leads to the complete unusability of the canvas. Manually, without using any special tool, it is unrealistic to make a tile cut perfectly even. To save your money, time and effort, we will consider all possible options for cutting ceramic products.

Angle Grinder

Cutting tiles with an angle grinder and stone wheels is just as popular as cutting with a tile cutter.

This method significantly speeds up the work, but at the same time, cutting the tiles, you will get a lot of dust, so this method is suitable for well-ventilated rooms, and for work carried out in the fresh air.

Professionals choose this method for large fronts of work, where smoother cuts can be neglected for the sake of the speed of finishing and repairing.

To cut a tile or tile using an angle grinder, we need:

  • Angle Grinder;
  • diamond blade for cutting stone;
  • pencil and ruler.

Before starting work, it is worth taking care of the means of protection of the respiratory system and eyes.

To cut, you need to take measurements, and then walk the angle grinder along the mowing line without any extra effort. The angle grinder must glide smoothly over the tile, otherwise it will chip. By repeating the same action several times, you will achieve a perfectly straight cut. It is worth noting that the angle grinder should be pressed against the side opposite to the notch. This will help minimize chipping.

Many professionals advise making cuts on the weight, then excess vibration will be damped by hands, and an arbitrary split will not occur. This method is good in that the unevenness obtained during work can be sanded using the same angle grinder.

Easy Tile Cutting Trick. No Measuring!

Figured cutting of tiles

Very often, a “g”.shaped incision is required to design protruding corners. Many fall into a stupor, because the tile cutter cuts the tiles strictly in a straight line. The simplest solution is to divide the work surface into two component parts. The first cut is made perpendicular to the long side of the tile, and the second is cut parallel, thus avoiding the terrible seam that is formed when two tiles are folded into the shape of the letter “g”.

You can also try cutting with a glass cutter and pliers. A sufficiently deep risk is made with a glass cutter, along which a break is made later with the help of pliers.

Sawing the tiles at an angle of 45 degrees is no less frequent practice than the curly cut. If your tile cutter has an inclined mechanism, then such an incision will not be difficult, but if there is no such mechanism, you should not be upset.

The tiles can be washed down using the same angle grinder “by eye”. Sand while keeping the tool slightly tilted. Such a gash is very often needed to hide the external, bulging corners of the walls, but this method is not recommended for rooms with slippery floors. It is safer to use curbs, which will make the angle less sharp, but will not spoil the perception too much.

For information on how to cut tiles at 45 degrees at home, see the following video.

Manual tile cutter

Among the amateur and professional builders, the most popular is the tile cutting method using a manual or machine tool tile cutter. This method is relatively inexpensive, but no less effective than working with an electric tile cutter.

The tile cutter, depending on the level and quality, costs an average of 300 rubles. You can find it cheaper, but the quality of such a tool is fully consistent with its low price. It is worth noting a number of other advantages of this tool:

  • Maximum safety. Even the smallest member of your family cannot be injured by such a tile cutter, unless he drops it on himself.
  • Easy to use. Many who have never used such a tool before, note that mastering cutting technology takes on average 10-15 minutes. At the same time, the cut quality does not differ much from the professional level.

The device of a manual tile cutter is considered as simple as possible. It uses a movable handle, at the end of which there is a cutting element and tabs that break the tiles. The main surface of the tool has a shallow groove, with the help of which the fracture is obtained as even as possible. It is very easy to split tiles diagonally using a manual or machine mechanical tile cutter.

The first thing to do is to secure the tiles and prevent them from slipping. Fasten with the front side to the handle. Then, without making great efforts, run the handle along the surface of the tile, forming a risk. The last action is to apply some force with the paws, which will lead to the tile breaking along the mowing line of the cut.

However, it is worth noting that a mechanical tile cutter does not actually cut anything, but only makes a subtle scratch or risk that violates the integrity of the tile face. This makes it possible to break the tile in the required place, without obvious damage in other places.

The main disadvantage of this tool is that it will be extremely difficult to make an incision, and then the hall of the tile edge less than 5-6 cm, which is a determining factor when choosing a cutting method.

Electric tile cutter

The best solution is undoubtedly the use of an electric tile cutter. This is a full-fledged professional equipment that will not only increase the speed and quality of the work done, but also increase your convenience. Such a tool can be considered a full-fledged machine: it is energy-consuming, massive and demanding to maintain.

Despite all this, the electric tile cutter is the leader among builders of all levels. from the amateur beginner to the professional. This method, despite its complexity, is considered the most productive and high quality than its counterparts.

In the device of an electric tile cutter, there is the same device as in a mechanical one. However, instead of a cutting element like a nail or a blade, this machine uses a saw blade similar to that used in an angle grinder.

When working with a large number of tiles, it is worth considering cooling the working surface of the saw blade with water.

Glass cutter

This option is only suitable for thin tiles. This method involves the use of a ruler, glass cutter and patience, but, despite all your efforts, it is quite difficult to avoid marriage: the tile strives to slip out or slide out from under the hand, thereby making the cut uneven, and in places of strong displacement, a split is possible, which will make the tile unusable.

For a correct cut, a deep scratch is made on the face side, which will then become the point of refraction of the tile. With this method of cutting, it is very easy not to calculate the pressing force: a strong pressure will instantly make a crack on the tile, and a weak one. a curve fracture.

Also, tiles can be cut with a nail according to the same principle, but this method can only be used out of despair, when nothing else, even a banal glass cutter, is at hand.

Output

Tile is one of the most popular ways to decorate and decorate buildings, and is considered the most practical option than its counterparts. Initially, the tiles were made of clay and covered with glaze. Now manufacturers are not limited to only one clay, but use stone, ceramics and even glass, although production technologies have not changed much.

The selection of the required size and shape of the tile is achieved by cutting it. For an ordinary person who is not associated with the construction industry, tile cutting is a complex, painstaking and not always successful process. However, in fact, anyone can handle this.

The choice of tool depends on the goals and type of work. A cheap manual tile cutter and an angle grinder are suitable for renovating an apartment, while for larger work, an electric tile cutter is indispensable. The process of cutting tiles is not difficult, however, you should not hope for luck and it is better to purchase a little more material. This will eliminate the need to run, pick up and buy the missing.

The appearance of the room and the quality of the work performed depend on the correct and accurate cutting of tiles.

You need to cut from yourself or to yourself?

There is no definite answer, this is individual. Try different options, the most convenient way will be right for you.

Instrument preparation

Before cutting the tiles with a tile cutter, check the condition of the appliance:

  • Understand if the tool has visually noticeable defects.
  • Inspect the cutter wheel for wear. Signs of wear and tear are chipping and curvature. The equipment must be replaced.
  • Clean any debris from the rails and platform. This is necessary so that the stroke is even and smooth, and the workpiece is held securely. Remove debris, large debris.
  • If the stroke is uneven, lubricate the carriage with a lubricant.
  • Tighten the fasteners.
  • Make sure the bed is in a stable and level position with enough space around for comfortable work.

Instructions

  • Put on the necessary PPE (goggles, respirator, gloves, etc.).
  • Make markup.
  • Place the workpiece on a flat surface (unnecessary plywood or a block of wood is ideal).
  • Start cutting at the mark. You do not need to try to make a cut at a time, so you will only break the product. Make some shallow cuts. Perform work by weight so that the vibration from the angle grinder goes into your hands, otherwise the workpiece will split. Place something soft (rag, towel) under the expected place of the tile fall so that it does not break after it comes off.

Work tips

  • Choose a model according to your needs. If you need to shorten several plates in the course of one job, you can limit yourself to a budget model. If you plan to use the device constantly. get a good manual (or even electric).
  • For a smooth ride, apply a drop of machine oil to the cutting element. Reduced friction results in a cleaner seam.
  • Guide the guide evenly, smoothly. No need to rush and change the intensity of movements.

Benefits

  • Saw off thin strips up to 20 mm wide.
  • Cuts porcelain stoneware when fitted with suitable accessories.
  • Many home craftsmen already have an angle grinder, with a small amount of work, buying a tile cutter will not be necessary.

Instructions

  • Place the workpiece face up.
  • Mark the cutting line.
  • Lay the ruler along the marked strip.
  • Firmly move the glass cutter along the ruler to form a furrow.
  • Grab the edge, push the workpiece.

How to cut tiles without a tile cutter

There are analogues of a manual tile cutter on the market. With some caveats, they provide the same functionality. Consider the most famous.

Features of using a tile cutter

We will tell you about the specifics of the operation of the tool: safety precautions, what tasks will cause difficulties, secrets, how to simplify the work.

What are the criteria for choosing a tool for cutting tiles

Before you start using a manual tile cutter, you should choose the right one, taking into account all the nuances and distinctive features. There are certain points that must be paid attention to:

  • full compliance with the stated requirements. The strength of the cutting part is selected taking into account the material intended for cutting, the maximum parameters of the depth and length of cutting are determined based on the parameters of the tiles used in the repair;
  • high-quality assembly. The tile cutter is visually inspected for defects, the lever is moved to make sure there is no backlash. From pressing the lever, the guides should remain even and not bend;
  • the possibility of trimming at an angle. A useful function, with its help, the tile material in the corner sections is adjusted as accurately as possible. The working platform is easy to adjust, the installation after fixing does not get lost, the backlash does not appear;
  • availability of spare parts and consumables that periodically need replacement.

Montolit masterpiuma 63p3

Another mechanical monorail model, equipped with a pair of millimeter rulers and side stop elements. It is used for cutting tiles and mosaic glass. A roller with a diameter of 1.4 cm cuts material 2.2 cm deep, weighs within nine kilograms, and costs about twenty-five thousand rubles. Made by an Italian company, used by professional craftsmen.

Hand tool for professionals and hobbyists

Tile cutters are deliberately divided into such groups. The amateur version is not very expensive, but does not withstand prolonged load. There is no additional functionality, or its quality leaves much to be desired. Such a tool is used for a single repair.

A professional-grade tool will cost you quite a lot, but the price difference will pay off with high-quality assembly and good components, accurate design calculations. Cutting is performed better, the operating period of the tool increases.

For convenient use, the set includes rulers, thrust elements, squares and other accessories. A tile cutter of this group is popular among decorators.

Enkor 3660

Power tool double rail tile cutter that cuts ceramic tiles. The diameter of the cutting roller is 1.5 cm, with a thickness of 1.5 mm and a bore size of 6 mm, which cuts tiles up to six millimeters deep. Such a device weighs only a couple of kilograms, costs within one thousand rubles.

The model is inexpensive and lightweight, it is considered a good repair assistant.

Manual tile cutters rating

We bring to your attention a list of models of manual tile cutters that differ in cost and technical characteristics, from which professional specialists and lovers of self-repairs make the final choice. Many craftsmen prefer the Sigma manual tile cutter, but there are other decent options.

Bars 87590

The cutting roller of such a mechanical tile cutter is 2.2 cm in diameter, the landing hole is 6 mm, additional corner stops allow you to cut tile material, the thickness of which is 1.4 cm.

The device costs five thousand rubles, weighs only eight and a half kilograms, provides a cut length of up to sixty centimeters.

Tile cutter for porcelain stoneware tiles

This material is stronger than facing tiles, and in work with it they use a special tile cutter. professional, equipped with bearings that ensure uniform pressure of the cutting edge on the material. In addition, the cutter must be made of quality metal.

You need a professional tile cutter to cut porcelain stoneware

The force required to cut porcelain stoneware tiles depends on the size of the lever, so choose the tool with the longest handle.