How To Cut A Wide Ceiling Plinth
How to cut a ceiling plinth correctly
This is how the corners of the ceiling plinth look correctly cut
You can make such an ideal ceiling plinth with your own hands if you follow these instructions.
For the manufacture of ceiling cornices, three materials are mainly used, these are:
They also make stucco ceiling cornices, but this is a different topic.
- The weakest and cheapest of them is polystyrene, although strength on the ceiling is not very required.
- Expanded polystyrene is much denser than it can be easily cut with a knife and, of course, it is more expensive.
- Wood is the hardest to handle. In order for the corners of the wooden skirting boards to be ideal, you must use an exclusively fine-toothed hacksaw, and even better a hacksaw for metal and a sandpaper. Only in this case can you achieve an even angle.
Trimming inner corners with a miter box
To do this, you need the following tools:
- The fillet is laid on the bottom with the miter box with the side that will be glued to the ceiling, and the lower side is pressed against the miter box wall, against its right slots.
- Fillet trimming is done with a hacksaw or a sharp knife. Cut carefully, without excessive force, so as not to deform the ceiling cornice and NOT chipping.
- In this way, cutting off the adjacent corner of the plinth, but already with the help of the left slots on the miter box.
- Then these parts are applied to the corner to check if there is a gap, then you can cut with a knife.
Tip: In order not to translate the material in vain and to acquire skills, practice first on small pieces.
How to properly lay the fillet in the miter box
Trimming adjacent fillets
Corner slicing technology
So, at what angle to cut the ceiling plinth and where does the formation of an angle begin with the help of home remedies??
First you need to measure the angle, which is between the walls. for this you can take pieces of foam from technology. Usually the angle is 90 degrees. a strict perpendicular. In this case, trim the edges of the product at an angle of 45 degrees. Perform similar actions with the second segment.
In the event of irregularities and mismatched joints in the gap between the ceiling and walls, you need to divide the corner radius in half. In this case, do not confuse the details. The baguette for the left side is notched, and the one on the right is the other way around.
Before cutting the ceiling plinths in the corners, form a corner inside the material in the upper space. this decision is based on the fact that the lower side protrudes above the upper one. When performing an outer corner, the procedure is reversed. The texture of polystyrene foam materials itself helps to smoothly and accurately fit the details. If wooden or plastic elements are used for the baguette, then you will have to work with them more carefully.
How to cut ceiling plinths in corners with and without a miter box?
November 11, 2015
The procedure for installing fillets on the ceiling seems quite easy, but it requires specific techniques to successfully complete the repair. Often we cut the corners of the ceiling plinth completely wrong, which leads to a reduction in its service life and a number of quality repairs. Correct joining, evenly fixed edges. the result is quite achievable if you use the recommendations of experienced specialists.
Cutting method with miter box
The most popular mounting option is with the introduction of household tools. The miter box is a renowned carpenter’s assistant helping to cut at the right angle. This is usually a tray, wood or plastic, with vertical slots for the blade at 45 and 90 degrees. How to cut the corners of a ceiling plinth with a miter box?
First, you should attach the material to the ceiling, install its bar in the miter box. In this case, the tool must match the position of the product. Holding the plinth with your left hand, choose a position for the cutting tool (hacksaw) at an angle of 45 degrees. The material is cut without undue pressure. After that, the striker is cut, set to the far wall of the wort.
Holding the working material with the right hand, select the position of the hacksaw at 45 degrees and cut.
How to cut a ceiling skirting board without a miter box. Cutting without tools
How to cut a corner of a skirting board without a miter box? It is possible to perform the calculation and cut manually. It is enough to make a good marking on the ceiling, then cut off the desired corner exactly. A significant disadvantage of this option is the inconvenience when you have to hold all the bars with your hands during the measurement process. In general, this method does not help to make the necessary measurements any worse.
Attached the product to the place where it will be mounted, you can immediately take into account all the errors on the walls. First, two pieces are cut at a 90 degree angle. Then one of the planks is applied, rests it against the wall perpendicularly. Draw the line along the ceiling, outline the desired contour. Then they remove the bar and apply a second one. for reciprocal marking. The intersection of the lines will be the bleed. Then the place for the future cut is marked on the slats.
Strong ceiling plinth: secrets of correct angles without using a miter box. Angle slicing
How to cut ceiling skirting boards in the corners? The secret of a high-quality incision is in making cuts both on the outside and on the inside. The inner cut matters if we make the outer corner.
Usually they use professional equipment. miter saws or industrial electric rotary hammers. But home renovation advocates can get by with conventional tools. The main requirement is that at the end of the work, the result should be a clearly visible texture for the cornice, reflected on its front or back side.
What is it made of and what is it called
The very first skirting boards on the ceiling were made of plaster. They were cast in special molds, then installed in a solution on the ceiling. Such figured ornaments were called fillets. Today you can see them rarely are expensive, and outwardly they almost do not differ from the cheaper options. And the name is almost lost.
The most popular ceiling skirting boards today are made of polyurethane or polystyrene. They are inexpensive, look great, are easy to install, have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. The exception is wooden houses with a corresponding interior. Wooden products are most often used here. the style dictates its conditions.
There is also a similar plastic finish. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips. they are NOT afraid of damp.
You need to cut the ceiling plinth in the corners of any material in one of the ways described below. The only exception is plastic skirting boards: such a corner can be issued only with the introduction of ready-made corners.
What and how to cut
Working with skirting boards made from different materials means using different cutting tools. When working with a wooden skirting board, it is more convenient to work with a saw on wood. All others, including plastic, made of foam and other polymers, are better cut with a metal sheet. The result is a smoother cut, less burr. Saws are usually used when working with a miter box.
Corner design looks attractive
When working with a polystyrene skirting board without special tools, they cut them with a good office knife. Its blade is quite thin and even, the cut is smooth, wrinkled. If you use a saw with hydro- or polystyrene, do not press hard: you can wrinkle.
In general, in order to get used to the tool and material a little, take some piece and practice on it: cut, saw, trim. So there will be fewer problems when working.
With the introduction of miter box
If the corners and walls in the room are even, you can use a special carpentry tool. a miter box. This is an inverted U-shaped chute in which the mowing line is marked for cutting at 90 ° and 45 °. The part in which you need to make a gash is laid inside, a saw is inserted into the guides. The part is held in place, cut to the desired angle.
This is what the miter box looks like. Can be plastic, wood or metal
In the case of a skirting board, not everything is so simple: they must simultaneously lie on two surfaces, therefore they need to be pressed against one or the other wall of the miter box. When working from the ceiling, they are pressed against the side closest to you.
The sequence of actions when finishing the outer corner, you need to make a gash at an angle of 45 degrees. Place the miter box in front of you. I try on how the plinth will be located, determining which part of it will be attached to the ceiling. In order not to get confused and cut off the ceiling plinth correctly, the bar that will be located on the right, We put the case, then that on the left is on the left.
How to cut a corner on ceiling skirting boards: correctly Install it in a miter box
The part that turns out to be on the ceiling presses against the lower part with a miter box. The other side is closer to you and raised. She is supported on the wall of the device so that she does not stagger when cutting. That is, the front of the skirting board turns out to be turned away from you. Do the cutting direction as shown in the photo below. By folding the two cut pieces together, you get a Protruding. Outside or Outside Corner.
How to Make the Outside Corner of a Skirting Board Using a Chair
First put the cut-off parts in place “dry”, without applying glue. If the geometry of the corner turned out to be not ideal for centuries, you can touch up a little with a knife. It is easier to cover small errors with a special putty.
The situation is very similar with the inner corner of the skirting board. First you try on which side will be on the ceiling, this part is pressed to the bottom with a miter box, the second part is supported on the wall closest to you and cuts as shown in the photo below.
How to make an inner corner of a ceiling plinth with the introduction of a miter box
And again, at first I try it on without applying glue, if necessary, I slightly correct it. Then apply a thin bead of glue to both surfaces that will stick to the wall or ceiling.
Your own version of how to use the miter box correctly is shown in.
How to get the correct angle
Most of the problems when working with skirting boards arise when making corners. Since the surface in the products is complex, it will NOT work simply to cut at the desired angle: it is also necessary to cut it so that they dock and, preferably, without large gaps. In reality, there are several ways to make the corner of the skirting board Perfect (or almost).
With decorative corners
There is one more, simpler way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory decorative corners. They are installed in a corner, strips are glued to them closely. Cutting them if necessary is very simple: a few millimeters with an ordinary clerical knife.
Examples of finished corners for fillets
How to cut ceiling plinth in corners
The quality of the ceiling finish greatly affects the appearance of the room. Then they try to do everything perfectly, or very close to it. The finishing touch to the design is the ceiling plinth. They give the finish a complete and holistic look. The strips themselves are mounted on flat surfaces simply: on special white glue, but problems arise with the design of the corners. Without knowing how to make the corner of the skirting board correctly, a lot of material deteriorates. How and what to cut it in the corners and tell you.
How to make a corner of a ceiling plinth without a miter box
Few people in apartments or houses have angles of exactly 90 °. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything “in place”. under the ceiling.
You will need a finely contoured pencil (hard. it is not so visible on the ceiling, but leaves quite clear marks near it), a small piece of plinth, a ruler and a good stationery knife if you work with polyurethane (polystyrene) baguettes or metal dust to work with other materials.
Apply the plinth to the corner, draw along the outer edge with a pencil. Apply to the other side of the corner, also mark. You have a cross on the ceiling, the center of which marks the place where the plinths of the ceiling plinth should converge (look at the photo). I installed a piece of plinth in the corner, which will stick there and resting it with its end on the wall, transfer the mark to it.
How to make corners on skirting boards without using special tools
Now take a ruler and connect the edge of the skirting board with the marked mark. If you just put the plinth on the table and cut along the mowing line, the two parts in the corner will still NOT fold: the inner part will interfere. You can trim it later, try it on the ceiling. The second way is to install a piece that needs to be cut on the table, then a piece that will be on the ceiling. And cut along the mowing line, but keeping the knife at an angle of about 45 °. It will still be necessary to correct, but much less (and less chance of error).
Repeat the same operation with the second bar. Attached to the desired wall, abuts the butt against the adjacent wall, mark the place where the cross is drawn, draw the line and then Cut it off. Correction Carried out “dry” without applying glue.
You repeat exactly the same steps for the outer (protruding) corner. Now you know one more way of how to make a corner of a ceiling plinth, and without a scissor or other special devices.
How to join in corners
If the installation of the first corner is completed, we can assume that you have already learned almost everything. “Almost”, because you still need to learn how to join the corners and cut the planks to length. When some part is already glued and a small distance is left to the corner, how not to be mistaken with the length? The answer is simple: leave stock.
At first, you can cut a piece 10-15 cm longer: it will be possible to redo it several times if something does not work out right away. Then you make the corner in the way described above, try it on dry, adjust everything so that the result suits you. Only then can the already cut bar be attached to the corner and mark the place where it can be shortened. You need to trim at exactly 90 °. It is not necessary to use a miter box. Just try to put the knife (hacksaw) perpendicular to the surface.
Features of cutting ceiling plinths in a miter box
It is necessary to work with this device extremely carefully so as not to blunt the tool and leave no cuts in unnecessary places. In the process, we adhere to the following instructions:
-
We fix the baguette in the miter box in the same way as it is planned to place it on the wall. The side that will press against the ceiling on the miter box should lie against the sidewall.
We insert a cutting tool (hacksaw or knife) into the desired gap and cut the fillet.
Cutting technology for ceiling plinths
For efficient and high-quality work, you need to choose a tool in accordance with the material of the baseboard and choose a cutting method. If you have a miter box, then there will be NO special difficulties in the process. If it is not there, then two options are possible: cut according to a template and measure on the ceiling or make this tool yourself.
Selection of tools for cutting ceiling skirting boards
To properly and accurately cut the ceiling plinth, you need to use a suitable cutting tool. It is chosen depending on the material from which the fillets are made:
-
Styrofoam. It is characterized by low strength and is inexpensive, and then foam models become more and more popular. Their strength does not particularly affect the performance, since usually the ceiling plinth is NOT subjected to mechanical stress. A regular stationery knife is suitable for cutting.
Extruded polystyrene foam. A cheap material with a density several times higher than that of foam. Because of this, cutting it is a little more difficult, and then a sharp and thin knife is used for THESE purposes.
especially if made of hardwood. Before cutting wood ceiling plinths, stock up on a hacksaw.
In addition to the tool for direct cutting of the baguette, you will need a miter box. This is a special device made of wood, plastic or metal in the form of a box with sawed off the sides. A hacksaw or knife can be inserted into it at the desired angle. Thus, the cutting angle is as accurate as possible.
-
We knock three planks of 5015 cm with a long edge into the shape of a three-sided, rectangular box. Please note that an angle of 90 degrees must be respected between the side rails and the transverse board.
Using a protractor, mark an angle of 45 degrees on the bars. Instead of a protractor, you can use a school square. In it, one angle is 90 degrees, and the other two are 45.
Method of cutting the ceiling plinth without miter box
To neatly dock fillets in the inner corners, you can do without a miter box.
We carry out the work in the following order:
-
We attach the end part of the baguette to the letter of paper and outline the contour of the convex side. It is more convenient to use a small piece of plinth (if any).
Cut out the resulting template.
We transfer the contour to the surface of the baguette with a simple pencil.
Cut along the drawn curve.
For fitting, one plinth is applied tightly with the end part to the wall, and then the second.
Rules for cutting ceiling plinths by marking
This method is used to cut skirting boards in cases where there is neither a miter box nor parts from which it can be made.
To do this, you need to make markings on the wall in this order:
-
We put the baguette in the corner to the place of fastening.
Along its one edge, we draw the base line on the ceiling for the level of attachment.
We apply the fillet in the same way to the perpendicularly drawn mowing line on the ceiling and again draw a straight line along one side. We should have two segments, which intersect at one point.
We again apply two plinths in turn and mark this point on them.
We repeat the same procedure now on the wall to mark on the products the place of cutting from below.
We connect two points with a line. It can run at an angle of 38-45 degrees, since walls and corners in living rooms are often uneven.
How to cut a ceiling plinth
One of the most difficult steps in installing skirting boards is cutting them correctly. Only by correctly joining the individual elements at the outer and inner corners will you get the desired result. Fillets will look aesthetically pleasing and neat if you cut them off at the right angle and seal the cracks. A special tool (miter box) is used to accomplish this task. And if it is not there, then other devices will help.
Technique for cutting ceiling skirting boards
This method can be used if your corners are even and you want to trim the baguette exactly 45 degrees. To do this, before cutting the ceiling plinth in the corners, you need to draw a miter box on thick paper. Draw two parallel mowing lines and mark the angles at the desired degrees using a protractor.
Placing the fillet in this case in the same way as in the traditional miter box. Please note that you need to cut the skirting board while holding the tool in a strictly vertical position.
Tips for cutting ceiling plinths
When working with a miter box, there are two things to consider:
-
The inner corner of the ceiling plinth is formed from two parts: the first we start the case in the miter box and cut from right to left, the second we start from the left and cut from left to right.
In addition, you need to know the following nuances before cutting the skirting board:
-
Before you start cutting a baguette with a miter box, try cutting a test strip to avoid mistakes.
You can make the correct measurements by measuring the length of the inner corners of the plank on the inner side, and the outer ones. these are the points of the inner corner for the width of the fillet deep into the room.
If the baguette is installed under a stretch ceiling, then it should only be attached to the wall. The adhesive composition should never get onto the vinyl sheet.
The final fixing of the skirting board should be carried out only after the exact fit of the plank.
If the corners and walls in the room are even, then you can customize it on the floor.
When installing baguettes, it may be necessary to adjust them several times, therefore, stock up on tools and patience.
Instead of a template and a miter box, you can cut in the corner between the wall and floor, or by moving the table against the wall. In this case, on the wall, ceiling and bug, you need to mark the cutting angle of the end.
If you are interested in the question of how to cut a ceiling plinth without a miter box, and you do not have time to use templates, then you can purchase special corner inserts in advance. They will hide the gaps, but will protrude and stand out on the coating.
If you have a skirting board made of precious wood, then you need to cut and install it very carefully, since a large amount of putty for sealing the joints will be too noticeable, and painting over the baguette is an inappropriate solution, because this way you will hide the natural texture of the solid wood.
Expanded polystyrene products do not have to fit close to each other due to the soft texture, but wooden and plastic models must be well docked.
In this case, cut off the plinth at an angle equal to half the joint. For example, if the walls are joined at an angle of 120 degrees, then we cut the fillet at an angle of 60 degrees.
How to cut a ceiling plinth. look at:
How to trim the corner of a ceiling plinth using ceiling markings
Marking the skirting board on the ceiling also allows you to cut the corner straight and precisely. The only drawback of this method is that it is difficult and inconvenient to keep the plinth strip suspended during the cutting process. For the rest of the tent, the angle for cutting in this way can be even more accurate than in other ways. Applying the plinth to the installation site, all wall flaws and deviations in the angle size are immediately taken into account.
Cutting the corner of the ceiling plinth:
- First of all, two workpieces must be cut at an angle of 90 degrees.
- Then we first apply one plank, rests its end against the perpendicular wall. We draw a line on the ceiling, outlining the contour of the plinth.
- We remove this bar and apply a striker, also rests its butt against the wall. We outline the line.
- The point of intersection of the marked lines will be the mark at which the skirting board needs to be cut.
- Again, we apply each bar in turn and mark the cutting point on them.
- We draw the line from this point to the second edge of the plinth.
We cut off the skirting boards along the outlined lines, join them and apply them to the installation site. Please note that this method is easier to cut inside corners.
How to cut a corner of a ceiling plinth using a miter box
The miter box is a simple carpentry tool that allows you to cut the workpiece at the desired angle. Most often it is a tray made of plastic, wood or metal with vertical slots for cutting at an angle of 90 ° and 45 °. There are also more complex miter box designs. for cutting at angles of 90, 60 and 45 degrees. For more professional work, a miter box with a swivel mechanism is used, where the hacksaw can be fixed at any angle to the workpiece.
How to cut a skirting board with a miter box. inner corner:
- We apply the plinth to the ceiling, measuring the required length.
- Then Install the plinth strip in the miter box so that the position coincides with the position of the plinth on the ceiling.
- The plinth strip must be pressed against the far wall of the miter box.
- Hold the plinth with your left hand.
- We choose such a position of the hacksaw when the angle is 45 degrees and the handle of the hacksaw is as close as possible to the left hand.
- We cut the workpiece, and without making excessive pressure on the saw.
- The next step is to trim the plinth striker. We also install it to the far wall of the miter box.
- Presses and holds with the right hand.
- We choose such a position for the hacksaw when the angle is 45 degrees and the handle of the hacksaw approaches the right hand.
- Cut off the skirting board.
Next, we join the trimmed plinths and check the cutting accuracy. For a more accurate orientation, they also say that to complete the inner corner, it is necessary to start cutting from the front of the skirting board. After cutting, wooden skirting boards will most likely have to be adjusted with a file.
How to cut a skirting board with a miter box. outside corner:
- In order not to be mistaken with the dimensions, it is better to start by marking the inner corner, and then cut out the outer corner. Otherwise, a situation is possible when the bar may not be enough in length.
- You must attach the plank to the ceiling and tent dimensions.
- Install the plinth strip and press it against the nearest wall.
- Hold it with your left hand and choose a position for the hacksaw at an angle of 45 degrees, when the handle approaches the left hand.
- Cut off the workpiece.
- Install the striker to the nearest wall, hold it with your right hand.
- We set the hacksaw at an angle of 45 degrees, when the handle approaches the right hand.
- Cut off the workpiece and join the corner.
Trimming the workpiece with a miter box is suitable only if the angle between the walls of the bumps is 90 degrees. If the accuracy is poor, you will have to use other methods.
How to cut a ceiling plinth using a miter box template
Something resembling a miter box can be done by applying the desired cut angles to paper, cardboard or wood. Draw two parallel mowing lines, locate the center, and then use a protractor to set the desired angles. The advantage of this method is that you can postpone any angle, including more than 90 degrees. Of course, before cutting the corners of the ceiling plinth, you must first check the angle between the walls using a corner and measure with a protractor.
The technique of cutting a ceiling plinth using a miter box drawn is exactly the same as using the miter box itself. The plinth plank is pressed against one of the parallel lines, then we set the hacksaw at the desired angle, which is already outlined, and cut off.
Ceilings
Ceiling plinth performs not only a decorative function, we visually separate the walls from the ceiling, but can also hide the joints of various finishing materials of the ceiling and walls. Not every interior design involves the use of a skirting board, but more often than not, the overall appearance of the room seems incomplete without it. There is nothing complicated in fixing this element. fillets. almost all types of skirting boards are attached with glue. But the question of how to properly cut the ceiling plinth in the corners of the premises can confuse many. Indeed, even in the simplest room there are internal corners, where the plinths of the ceiling plinth must be precisely and beautifully docked. And in a more complex configuration of the room, you will also have to dock the skirting boards, performing the outer corner. In this article we will look at various options for how to cut a ceiling plinth with and without tools at hand.
First you need to figure out how to cut the ceiling plinth, the answer to it depends on the material from which the fillet is made. At the moment, we sell ceiling skirting boards made of polyvinyl chloride (PVC), expanded polystyrene (foam), hydro and wood.
PVC ceiling skirting boards are the cheapest. Dents and creases are easily formed on them, which cannot be removed, so the product has to be thrown away. Also their disadvantage is electrostaticity. the ability to attract dust. You can cut them with a sharp construction knife or hacksaw.
Styrofoam ceiling skirting boards are also cheap. This material is very fragile, it crumbles easily during processing, therefore, it is necessary to cut the expanded polystyrene with a sharp knife or a hacksaw on metal, and not making too strong pressing forces.
Ceiling skirting boards made of extruded polystyrene foam are slightly more expensive than polystyrene foam, they are denser and more difficult to cut. However, they crumble less, making them easier and more comfortable to work with. Cut with a construction knife and a hacksaw for metal.
Polyurethane ceiling skirting boards are the most expensive at the moment. They are durable, elastic and moisture resistant, can be easily cut with a construction knife and DO NOT crumble. The disadvantage of polyurethane skirting boards is their dependence on temperature changes. For example, over a gas stove, a polyurethane skirting board will permanently deform and crackle slightly. If you try to process or cut such a plinth, it may bend or deform in a second way.
Wooden ceiling skirting boards are dense, heavy products that can only be cut with a hacksaw, preferably with fine, dense teeth. You can also use a cloth for metal.
Before proceeding to the enumeration of the ways how to properly cut the ceiling plinth, I would like to note that there is a possibility NOT to cut the plinth with particular precision. On sale there are special corner elements, into which the edges of the skirting board are inserted. In this case, it is enough to cut the plinth strip at an angle of 90 °, and the corner element will hide all the flaws. But this method is not always used, since the dimensions of the corner elements are slightly larger than the baseboards themselves, so the corners in the room will stand out against the general background. Sometimes it can look bulky. However, if the design of the room allows the use of corner pieces for ceiling skirting boards, it makes sense to use them. Further instructions will be useful for those who nevertheless decided to accurately cut the skirting boards at a given angle.
DIY impromptu miter box
Making a miter box with your own hands is also not difficult.
You will need three wooden planks or boards, which must be put together in a U-shaped box. Then the required angles are marked on the walls of the box, and a cut is made with a hacksaw. In total, you should get a wooden miter box in which grooves are cut.
A combination of an impromptu miter box and a template with marked lines. For the convenience of cutting, it is necessary to build something in which it will be convenient to hold the plinth strip, since it is difficult to keep it suspended. Enough to put together a corner from two wooden planks or boards. On paper, you need to draw a mowing line with angles for cutting at 45 degrees or at any other. Then we apply the skirting board blank to the corner, presses it by hand, as described in the technology of using a miter box, a piece of paper with a template is moved under the edge where we are going to cut, and Cut it off. In the process of cutting, we focus on the line drawn on the paper.
As an impromptu miter box, you can use anything, anything. What is forming a corner. For example, a table pushed against a wall.
It is NOT worth fixing the plinths of the ceiling plinths to how you cut the striker and tried on their location. Only after the two strikers are perfectly aligned in the corner, you can start attaching them to the ceiling. Minor flaws can be finished with a file or a nail file in the case of wooden and polyurethane skirting boards. To fit foam products, you will have to wield a sharp knife.
If suddenly, even after adjusting the skirting boards, a small gap remains between them, do not despair, it can be repaired with putty. Cutting the ceiling plinth yourself is not difficult. But in order not to spoil many products, it is better to pre-train on small blanks.
The first way is with a miter box
The miter box usually looks like a tray with vertical holes for a hacksaw. It can be made of wood, metal or plastic. This tool is the oldest and simplest carpenter’s tool for cutting wood pieces at 90 ° and 45 °. There are types of such a device for professional work, with a swivel mechanism, in which the cutting tool can be rotated and fixed in any position.
How to cut a ceiling plinth correctly
Ceiling corners are divided into internal and external, the method of joining them is slightly different.
Method two. no additional tools
For the inner corner, you can use the simplest way of perfect joining. by marking on the ceiling. Another example of how to cut a corner nice and even.
- Apply a fillet to the ceiling, tightly presses its even edge into a corner.
- Draw a line along the long side of the plinth on the ceiling.
- The same action is done with the adjacent part on the other side.
- Mark the point of intersection of lines.
In total, you get an even angle of 45 ° if you draw the line from the point of intersection to the edge of the part. Note that the above method of marking works only at perfectly flat corners.
How to cut the corner of a ceiling plinth straight
A beautiful and neat edging of the ceiling hides the joints of the border with coverings and is an additional element of the room’s decor. But in order for the ceiling plinth to look really beautiful, you need to be able to qualitatively join its corner joints.
How to cut the corners of the ceiling plinth evenly can be found in our article.
Related article: how to properly glue the ceiling plinth with glue and putty.
Inner corner
- We make the right measurements.
- We install the plinth plinth in the miter box so that this position exactly coincides with the placement on the ceiling.
- The plinth should be firmly pressed against the opposite wall of the miter box. Hold and press with your free hand.
- We put a hacksaw at an angle of 45 ° in a special hole and cut off the part.
- The adjacent part must be cut in the same way, only in a mirror image, as shown in the photo.
Outside corner
- Measure the length of the plinth from the nearest wall to the outer corner, leave the fishing line on the wrong side with a pencil, indicating the desired length. It should be noted that the edge (its upper part) should extend slightly outward.
- The plinth is moved to the miter box and cut off.
- The adjacent strip also needs to be measured with a margin and cut off in a mirror image to the first part.
Trying on a ceiling plinth: the joining of the parts should be perfectly even. If the result is not achieved and there are irregularities at the joint, you can trim the edges with an ordinary knife to a perfect joint.
Checking the smooth docking
All the nuances are well described:
other methods
With a good eye and accuracy of hand action, you can use a homemade template that resembles an imitation of a miter box. To do this, take a thin board or thick plywood and draw a layout in the form of a horizontal rectangle. Using a protractor, mark 45 ° on the right and left sides of the rectangle. Mowing line lines connecting opposite edges. You can now cut the ceiling plinth using this layout. The actions are simple and similar to the description above in the first option. Only the ceiling parts should NOT be inserted, but put on the drawing and combine the hacksaw with the layout of the layout.
Special accessories for docking