How to cut alline slate how to correctly. The key features of ondulin

How to cut ondulin across the wave

How to cut ondulin along and across? Which tool can be done evenly and carefully?

That’s what with what, but with cutting this material there are no problems. It is soft enough and easily cuts with a conventional knife.cutting wood. But it is also necessary to take into account the fact that ondulin is made on the basis of bitumen, and he (bitumen) will quite quickly score the teeth of a hacksaw and it will stop sawing. Therefore, before sawing, lubricate the canvas with oil and do not forget to carry out this procedure from time to time, then you can safely cut as many sheets with one hacksaw. What I personally like to cut with a hacksaw, the cutter is clean and even and you can cut the sheets anywhere.

The basis of Ondulin is bitumen materials.

That is, the material is quite easy to cut.

You can cut ondulin and across and across.

It is convenient to cut along the usual building knife

It is better to cut the “waves” of Ondulin, but between the waves.

Cut from the front side, then just break off onedulin and, if necessary, cut.

If it is necessary to cut off ondulin across, then the best option is a regular hacksaw on wood, with a small tooth.

Various high-speed power tools (angular grinding, for example), it is better not to use.

High speeds warm the surface of ondulin, it becomes extremely soft (see. Above about bitumen), the cut will not be of high quality, and the cut.off circles will be quickly clogged.

If the task is still to mechanize the process, then it is better to use a battery tool, because working on the roof (ondulin, this is roofing material) with network, is not convenient.

There is on sale for example, batteries,

How to cut a sheet of metal tiles?

Mark the place of cutting, you can use the flomaster other from the color of the color, you can marker, or by the usual building pencil.

Design the place on the so.called “crests” (well, or “waves”, it may be more understandable), clearly draw all the bends of the metal tile.

How unravelly it will sound, but the option with a “corner grinder” will have to immediately cut off.

I understand that the “corner grinder” was created for this, but the manufacturer of metal tiles is very strong against the “Bulgarians”.

“Corner grinder” heats the metal, as a result of this, the protective polymer layer becomes unusable, after a couple of years in the place of “cuts”, you will find rust, in which case it will not be possible to replace, the guarantee will be canceled.

Metal tiles can only be cut with a tool that does not warm the metal.

Manual, or electric metal tanks, manual not all are suitable, more convenient for the so-called “shade” scissors in metal,

They are just adapted to cut non.flat metal corrugated products in their design.

Electric ceremonies are of different types (types), there are three of them, any suitable, but more conveniently knife.

They even cut an electric lobium, but I think that this is pampering, and the temperature that is not desirable, it can create on the surface of the metal, the same option will turn out that with the “corner grinding” (wrote above).

Well, at the end I will please. The cutting speed of “carved” hand scissors is not lower than the cutting speed of “corner grinding”.

It is convenient to work with hand scissors directly on the roof, you do not need a power source.

The metal tile consists of several layers:

When cutting metal tiles, you should try to damage the protective coating as little as possible, t.to. After a while, metal corrosion will go. Well, you can cut both along and across the waves, and while using the tool that the manufacturer recommends. But if this is not possible, then you can use:

  • scissors for cutting metal, though working with them will turn for you into torture.
  • Scabble for metal. On a flat surface makes a good straight line for a trimmer. On curved surfaces it is better not to use it.

During work, preferably unused part of the sheet, cover something, so as not to spoil the protective coating with chips.

It is worth knowing that some “craftsmen” use an angular grinding machine (angular grinding) for cutting the metal tile, after which the fishing line for the trimmer of the cut is painted and claim that the protective properties of the material are fully restored. After processing corner grinding, the probability of corrosion is very high, so almost all manufacturers prohibit its use when installing their products.

The advantages of the slate and its properties

The slate has some advantages over other roofing materials:

  • It is very resistant to temperature differences;
  • has high moisture resistance;
  • stability to ultraviolet rays;
  • excellent sound insulator;
  • can be used in other areas of construction.

After the leaf fracture along the line of marking the edge, it must be sanded. Cutting the slate is easiest outdoors. The sheet is placed on the pallet or on the tables standing next. A gap is necessary for free tools. The most commonly used angular grinder is used.

The wave slate removes excess water well. This property allows you to use it as a roofing material for the roof of the house, garage, household buildings. Can be used as a formwork that prevents the penetration under the construction of groundwater under construction. During the performance of work with slate, you need to remember its fragility.

Before cutting slate, you need to provide protection from the hit of its small particles on hand and face. If you recall its composition, you will immediately have to highlight asbestos. This is a very harmful substance for health. Therefore, the respirator will not be superfluous when working with this material. It is recommended to work in protective gloves and masks. To protect against dust, moisten the spaces of sawing with water.

When using these tools before cutting cutter, you need to put the fabric moistened in water for several hours on a fishing line for a trimmer of marking. Then use any of these tools.

How to cut a wave slate

Often, when laying slate, you have to trim and cut entire sheets as roofing material. How to cut slate is a matter of difficult. This can be done in a few different ways:

A special disk for cutting stone is installed on it. When working with a corner grinder, you need to not only put on personal protective equipment, but also take into account the direction of the wind in order to protect yourself from dust. The assistant at this time can moisten a fishing line for a cutting trimmer with water.

Before cutting the slate with a corner grinder, it is advisable to wet the cut site.

Slate can be cut using a circular saw. An electric jigsaw is also suitable for this purpose. When working with these tools, you need to constantly monitor the distribution of force and the direction of the saw so that the material sheet does not break in an unnecessary place. Schifer cutting can be done with an ordinary hacksaw and cutter. They are not connected by wires, more convenient in work. The cutter is more suitable for cutting flat material.

And what is the slate of the wave if the owner does not have any of the listed tools? In this case, you can do as follows:

  • On a sheet of roofing material, you need to draw a future fishing line for a trimmer of a cut;
  • With the help of a hammer and slate nail, as many holes as possible are filled along the line;
  • A rail is placed under a sheet in this way, and the sheet is blown up.

It is recommended to saw slate with a power tool in cases where you need to cut part of the sheet. The wave product is cut only along the upper part of the wave. This achieves that the disk of the tool does not cling to the sides to the waves. It is better to use a corner grinder and a circular saw in manual version. The disk must be selected correctly in diameter.

Shifer tapping scheme.

You can cut an asbestos.cement sheet with improvised materials. You can use a piece of rim from the barrel. A piece of about 20 cm is chopped off from it. On the slate, a fishing line for a trimmer is planned and boards are laid under it so that the trimmer fishing line is between them. Accurate strikes of the hammer on the plate attached to the cut line, cut the sheet. First, the plate will try to leave in one direction or another. After a short training, everything will work out, it turns out a completely even cut. The impact force depends on the thickness of the sheet of the slate, on the weight of the hammer. The plate should not have pointing, its edge should have a rectangular shape.

You can cut the sheet using an ordinary electric drill. This is done very simply: a small diameter drill is inserted into the drill cartridge, and the roofing material is drilled in compliance with the minimum distance between the openings. Then they break it. The edges are improved by nippers, pliers, which are bitten by small pieces. Than cutting slate, now it is clear.

Step.by.step instructions on how to cut flat slate

Thicker shale tiles are more difficult to cut. Thus, it is better to cut a thicker shale tile slower than a thinner. If you cut the shale tiles in a dry way, get ready to use all kinds of protective devices, such as safe glass, bears, face masks, etc.D.

So that you do not inhale and are exposed to the dust formed during the cutting of a flat slate. It is better to cut slate in an open place with all protection measures.

Take the tile and fix the tool on the stand, table or on another plane.

  • Then connect the tile to the current and turn it on to check how it works?
  • Before you actually cut a flat slate, practice a little, cutting off a piece of slate so that you are used to the principle of operation of a tiled saw.
  • Now measure and mark the tile and place the tile on the table for cutting.
  • Combine a diamond disk with a tile mark.
  • Do not forget to put on all protective devices (glasses, take, masks, etc. D.). Before turning on the tile.
  • Move the cutting table to the diamond disk. When the blade and slate tiles contact each other, move the tile slowly, without much effort and so that the blade can perform work (as if on its own).
  • After you finish cutting the flat slate, turn off the saw and let the disk stop rotating before leaving the saw.
  • Disconnect the saw from the network to reduce the likelihood of an accident. You can connect it again when cutting another slate tile.

It was about how to cut a flat slate (dry cutting of a flat slate). You can even try wet slate cutting. With this method of cutting tiles, less dust forms, but there is a dirty mess remain.

When you finish wet slate cutting, wash it well and let it dry completely for some time before using it for installation for your project or crafts.

slate, correctly, ondulin

Materials for work

  • Water
  • Safe glasses
  • Roulette
  • Chalk
  • Gloves
  • Wet circular saw with diamond disk
  • Flat slate

The texture of the slate is rough and sharp, it is carefully cut with a chisel, and then cut with a wet saw so that it does not break into a pile of small pieces.

Separate separation allows a person to design a piece of slate in accordance with his needs and sizes.

  • Collect the flat slate together that you are going to cut. Flat slate is cut into pieces, large enough to fit in a wet saw. Put one of the flat plates on a flat surface and completely soak it with water. This prevents the cracking of stone during cutting.
  • Mark the desired measurement on the surface of the flat slate using a roulette and a piece of chalk. The purpose of the measuring mark is to serve as a guide while you cut it in a straight line, until the slate is divided into two separate parts.
  • Put on the goggles. Place the tip of the disk above the end of one of the measuring marks. Slowly lower the cutting tool over the line and begin to smoothly move the flat slate forward so that the disk manages to cut it exactly.
  • Take a piece and walk on a measuring machine machine. Make a trial breakthrough on flat slate. Slowly move the tiles forward until it is divided into two separate parts.

Laying roofing on the roof

Detailed instructions for laying an euro.shifter will help to correctly perform a roofing flooring of ondulin and similar in structure of materials that are massively produced by many manufacturers. Installation errors can lead to a roof flow, incorrectly laid ondulin can tear or break a squirrel wind.

So that the roof of ondulin looks beautiful, you should nail the material with nails, focusing on a pre.stretched cord. In this case, the heads of the fasteners will be located in even rows, and not a different. For fastening one sheet, 20 nails are required.

In order not to damage the sheets of material already laid on the roof, when installing ondulin, it is necessary to use the staircase that hooks behind the horse and does not press on the finished coating.

To designate the guides when laying sheets, it is necessary to pull the cords on the end of the roof and at the ends of the slopes. The size of the decoration of the roofing over the edge of the roof depends on the selected storm system. The edge of the roofing should be located approximately along the axis of a storm gutter, if it is provided.

How To Cut and Sew A Turtle Halter Neck Gown Special announcement!

To properly lay the roofing material, the first leaf of ondulin is mounted in one of the lower corners, focusing on stretched cords to avoid distortions and subsequent cutting of sheets. The lower row of roofing material is especially firmly attached. it must be nailed with a nail in the crest of each wave.

For the next row, it is necessary to cut one sheet along two halves. If each even row start with a half sheet, the number of joints decreases and the roofing flooring has a higher strength. For fasteners on the roof of the second and subsequent rows of Ondulin, it is enough to drive nails through one wave of sheet.

The hobby is crowned by the pitched roof, for its arrangement it is best to use the proprietary products of Ondulin, so that the roof looks as organic as possible. The cover of the skate should be at least 150 mm overlap the edge of the upper row of the sheet coating. The material is nailed vertically to the ridge beam and to the Euro.strifter coating through the wave.

Large Cross Cut Sled. Essential Table Saw Jig.

When arranging a complex roof roof, it is necessary to properly perform waterproofing joints and installation of apples. Roofing manufacturers of Ondulin propose to put branded yendov and use a special waterproofing tape. You can also use bitumen.based sealants.

If it is required to provide ventilation of the undercarbon space, special elements are installed under the cornice that prevent the penetration of birds and insects. If the roof is non.prefabricated, it is required to fill out the intervals with a special material.

For the design of the ends on the edges of the roof slopes, a special material is attached to the function of a windproof bar. If Ondulin is mounted on the roof in warm weather and is quite elastic, you can just turn the edges of the sheets protruding behind the plane of the ramp, and fix it with nails from the back of the rafters.

Learn to properly put ondulin on the roof on your own. Find out how to lay and nail the ondulin along with thematic videos.

Rules for cutting a Euro.shifter

To obtain a flat cut during cutting, the following rules must be followed:

Since the composition does not include substances harmful to human health, protective means are not used in processing.

Mark the marking with a colored pencil using a wooden rail 220-230 cm long or cutting. The pencil is selected by a contrasting shade in relation to the color of the roofing material.

Marking and cutting should be carried out on a flat flat surface. It is not recommended to do this on the roof. there is a great risk of damage to the bearing elements of the roof, it is impossible to firmly fix the product.

Before cutting ondulin, it is necessary to securely fix it, otherwise it is impossible to achieve good quality.

It is advisable to control a cut in a straight line with a rail or trim.

It is better to cut in the shade, since in the sun this material heats up and becomes soft, which makes it difficult to process.

At temperatures below.5 ° C becomes fragile.

Bitumen, which is part of the euro.shifter, inevitably sticks to any cutting tool. To quickly clean the canvas, it is periodically wetted in kerosene, toluene or solvent, you can wipe the surface with a rag moistened in them.

Sheets that will be at the joints are cut not at right angles, but under an inclination, so that the gap between them is a minimum. The seam is closed with one wave from Ondulin. There are special decorative details on sale, but they look worse.

Review of cutting tools

If it is needed for cutting a small number of elements only along or their fitting on small fragments of the roof, then you can use the usual construction or stationery knife with a retractable blade. The incision is performed on the front side, then the sheet is bent in half and finally cut.

Cut the wood with a hacksaw and an electrician.

Euro.shifer cut across the wave well with a hacksaw. Tools with a canvas 350-400, with small teeth and a thin saw, are suitable for working with ondulin. In the process, inevitably sticking small particles on a hacksaw, so it is pre.lubricated with oil and periodically lowered into cold water.

First, marking is applied to the sheet, then all the tops of the waves are cut to a depth of 1.5 cm. After that, they turn over, cut the upper points of the depressions and turn off in the cut. The method is suitable for a small volume.

The electric jigsit cuts along the same principle as a hacksaw. The file is chosen on wood with large teeth, better from well.known manufacturers. Bosch, Makita. Since ondulin sticks on the canvas of an electrician faster, this tool is used less often.

Circular or saber.saw and angular grinding machine.

The best option for cutting a large volume according to experienced builders is a manual circular (disk) saw. It provides a perfectly even cut, quickly processes a large amount of material. It is better to choose a disk with the largest number of teeth. You can clean it from sticky particles by cutting a piece of wood. It is convenient to cut off the Euro.shifer and along and across. The disk is periodically recommended to lubricate with machine oil.

Less commonly used a saber saw instead of a disk. Both the circular and a saber tool can independently process several sheets at once. To do this, they are preliminarily fastened to a pack and aligned. The thickness depends on the diameter of the disk or the length of the file.

You can use a corner grinder (angular grinder) with the thinnest disk. Cut a corner grinding machine you need to very carefully. When working at high speeds, there is a great risk of melting edges.

  • When selecting color, it must be borne in mind that Euro.shifer is prone to fading in the sun.
  • The smaller the size and number of waves, the more overlaps between the elements of the roof, which means that the strength of the roof is higher.
  • If the installation is carried out by one person, then again it is better to choose sheets of the smallest dimensions and weight.
  • When buying, be sure to pay attention to the thickness. If it is less than 3 mm, then the material is poor.quality.

Classical. It has 10 waves 36 mm high, the step between them is about 95 mm, dimensions are 2000×950 mm. Most often used for decoration of flat and vaulted roofs.

Smart. From the classic ONDULINE SMART is characterized by the presence of markings for fasteners-grooves and a clever locking castle. It has slightly smaller dimensions. 1950×950 mm, thickness and number of waves. like usual. The weight of one element is about 6.3 kg. Smart Castle prevents the ingress of oblique rain or melt water. Especially suitable for decorating the roof of residential and public buildings.

DIY. Already classic, its dimensions are 2000×750 mm, the number of waves is 8. Standard thickness. 3 mm, weight. about 5 kg. often used in areas with difficult climatic conditions. This is due to the large number of overlaps between the sheets, due to which the roof is stronger.

Compact. Has the smallest dimensions. 1000×750 mm. Thickness. 2.6 mm, weight. 2.5 kg, number of waves. 8. Suitable for finishing the roof of a small area or complex shape. Due to the largest number of overflows, less thickness is compensated.

The price depends on the manufacturer, such as the size of the batch, color.

The view of Ondulin Price, /sheet
Classical 450
Smart 370
DIY 300
Compact 170

Euro.shifer of one manufacturer and brand, but of different colors can differ significantly in price.

Scissors for metal: for cutting angles

Let’s start with the smallest works. So, there is one method that allows you to save well on scraps. If you do this, then the side slopes are perfectly even, and the sheets do not have to be cut in half at all.

The whole secret is that here the Ondulin is cut only in the corners, and not half the sheet is half. What’s the problem? Why is it even bad to cut ondulin? He does not suffer from corrosion?

The fact is that such seams are not always accurate and accurate geometry. And all this then affects the appearance of the roof and the tightness of its compounds.

In the classic installation of Ondulin, the so.called thickened seams form at the intersection of longitudinal joints. They turn out when the sheets lie on each other. And it is here that there is a chance that water will flow in this place and snow will be blown.

But cutting angles in this case significantly reduces the thickness of this overlap, at least 50%:

In a word, everything is solved simply. The extreme sheets that join at the corners should be cut with scissors for metal or hacksaw, while slightly tilting the blade at a certain angle.

And close the junction of the joint with one cut.off by an ondulin wave or a special prescription element that manufacturers release today. The dimensions of the trim itself depend on the size of the overlap, and it depends on the selected brand of Ondulin and the parameters of its sheet.

The trimming of corners, by the way, is often practiced by a milling. But thanks to the use of scissors for metal and patience, the cut is especially even and pure.

Cutting according to the rules: techniques and methods

Having figured out how to cut Ondulin and cleanse the tool, you should get acquainted with the rules and techniques of the process. Simple recommendations will help cut the most efficiently as possible, and not spoil the Euro.Shifer. It is worth taking care of the working conditions, what the following tips will help:

  • Ondulin cannot be cut on the roof. Soft material cannot be fixed under the slope. It will shift, and the marking will turn out to be inaccurate, errors and marriage are entirely possible. Also, during the cut, it is likely to accidentally damage other elements of the roof.

Cooling a hacksaw in a bucket Source.ru

Construction knife: for small tasks

If the sheet still has to be adjusted on the slope and cut completely, then let’s start with the simplest tools. So, the usual building knife quite easily cuts ondulin along the waves.

Just try not to rush so that the edge is even, and do not be lazy before making markings:

But abroad, Ondulin love to cut with a dense stationery knife. The one is good because it has a sharp, periodically replaced blade:

Try this method? Then you will need a clerical knife, level, marker and roulette this venture. And then everything is step by step:

  • Set the extreme points of the distance of the desired segment.
  • Take another leaf ondulin, attach to the points and draw a marker along the wave.
  • Make an incision.
  • Turn the sheet over and cut it to the end. Turn over.

Note that such an almost office tool is quite convenient, especially if you need to cut not much. Just be careful in efforts, because the blade of such a knife can unexpectedly break off and bounce.

Wood hacksaw: we will use improvised tools

Let’s look at this process more attentive. You can simply cut the sheet roughly, as in the illustrations above, or do it more competently and with less effort:

  • Take a hacksaw with large teeth and cut all the peaks to a depth of one and a half centimeters. No more deeply needed.
  • Dip the hacksaw in oil or water. It is even better to use an oil spray, which is convenient to sprinkle directly onto the teeth of the saw. But, if you do not want to use the oil so as not to get dirty yourself, then hold a bucket with cold water next to it and add ice from the refrigerator from time to time. Cold water will be no worse.
  • Now turn over the sheet, and the depressions will become the same peaks. Cut them and then turn overin.

Here is a more detailed instruction to work with this tool:

Of course, if you need to cut more than 200 square meters of Ondulin, forget about the hacksaw. In this case, it is better to arm yourself with a manual electric saw or circular.

How to cut ondulin and how to correctly? Step.by.step technology for working with tips which tools are suitable for cutting an euro.shifter

Nowadays, almost every roof of the house is equipped with any insulating materials. Scientific and technological progress made it possible to create a coating that will stay for a long time, protect the roof from various harmful factors.

However, even such raw materials are wear, since atmospheric precipitation, greenhouse effects and much more mostly acts on these coatings. The question arises here: “How to protect the coating and how to extend its service life?””

In this case, the product of the French brand. Ondulin comes to the rescue. For a year now, the company has been trying to surprise its consumer and releases a wide range of selection of this product.

To figure out how to handle it, you need to understand what it is, how it is arranged and study all existing species.

What is “Ondulin

A simple layman may not know about the existence of this product. To fully figure it out, you need to start with the basics. It is one of the varieties of the so.called “isolation”.

Its purpose is to protect thermal insulation materials from harmful effects of the atmosphere. The accumulations of condensate, various precipitation, strong wind and much more can be considered such.

If you do not pay attention to the increased humidity, which occurs due to accumulation of condensate for a long time, mold may appear, and home ceiling will begin to deteriorate.

That is why a reliable protection is needed, which can delay the greenhouse effect and protect the home from moisture.

Experts have long studied this material and created a list of spheres in which hydraulic insulation can be used. This includes:

  • Waterproofing the roof of the house. It is worth noting that the coating is produced in two layers to completely block steam.
  • Insulation of structures from light alloys of metal.
  • When laying the flooring.
  • Wall or attic insulation.
  • Creation of steam.banking during construction measures.
  • General insulating measures to increase the resistance of various building materials.

In general, you can notice that these products are widely used. For more than one year, consumers turn their attention to this particular film, because its characteristics are really high.

Ondulin Smart Rv

One of the most popular species of Ondulin is rightfully considered Smart RV. Such a film is considered “smart” because it contains many auxiliary materials.

Usually, the film is a canvas in gray colors. Special layers are applied to them, which are saturated with various impurities.

The main of them can be considered ultraviolet sterilizers that are designed to block the harmful effects of ultraviolet rays of the sun, as well as its radiation.

The next most important is the specialized membrane that performs the functions:

  • Protection from dampness, moisture.
  • Moisture drive during long.term rains and snowfalls.
  • Protection against ice flows of air, due to which humidity can form and gradually destroy the roof.

To understand what kind of coating it should look at its technical parameters:

  • The mass of a square meter is in the range of eighty.five grams.
  • An indicator of stability to breaks from five hundred to six hundred Newton.
  • Permissible limits of operating temperatures from minus forty to plus eighty degrees Celsius.
  • The indicators of water resistance are very large. more than a thousand millimeters of the water column.
  • Combustibility class. three. That is, it is subject to combustibility.
  • Ignorance class. two.

Ondulin RS

Another line of the French company that differs from its previous reinforcement. Additional reinforcement measures made it possible to increase its characteristics and make it more reliable.

Of course, because of this, both the mass of the product and its price increase. But, this is due to the fact that such a film can also tease on the unspleily sections of the roof and can easily replace waterproofing materials.

At the same time, all characteristics associated with moisture protection also remain at a high level. This model is beautiful for houses that are located in an aggressive climate.

Than and how to cut ondulin correctly?

ONDULINE. leaf roofing material with a base of pressed cellulose (cardboard), soaked in bitumen with polymers. Has a wavy profile, a rough surface, covered in several layers with paint. Euro.shifer has flexibility, so the cutting of it and processing of the house does not represent special problems.

  • construction knife;
  • knife.haired woman;
  • manual circular (disk) or saber saw;
  • corner grinding machine (corner grinder);
  • Electric.

Rules for cutting a Euro.shifter

To obtain a flat cut during cutting, the following rules must be followed:

Since the composition does not include substances harmful to human health, protective means are not used in processing.

Mark the marking with a colored pencil using a wooden rail 220-230 cm long or cutting. The pencil is selected by a contrasting shade in relation to the color of the roofing material.

Marking and cutting should be carried out on a flat flat surface. It is not recommended to do this on the roof. there is a great risk of damage to the bearing elements of the roof, it is impossible to firmly fix the product.

Before cutting ondulin, it is necessary to securely fix it, otherwise it is impossible to achieve good quality.

It is advisable to control a cut in a straight line with a rail or trim.

It is better to cut in the shade, since in the sun this material heats up and becomes soft, which makes it difficult to process.

At temperatures below.5 ° C becomes fragile.

Bitumen, which is part of the euro.shifter, inevitably sticks to any cutting tool. To quickly clean the canvas, it is periodically wetted in kerosene, toluene or solvent, you can wipe the surface with a rag moistened in them.

Sheets that will be at the joints are cut not at right angles, but under an inclination, so that the gap between them is a minimum. The seam is closed with one wave from Ondulin. There are special decorative details on sale, but they look worse.

Review of cutting tools

If it is needed for cutting a small number of elements only along or their fitting on small fragments of the roof, then you can use the usual construction or stationery knife with a retractable blade. The incision is performed on the front side, then the sheet is bent in half and finally cut.

Cut the wood with a hacksaw and an electrician.

Euro.shifer cut across the wave well with a hacksaw. Tools with a canvas 350-400, with small teeth and a thin saw, are suitable for working with ondulin. In the process, inevitably sticking small particles on a hacksaw, so it is pre.lubricated with oil and periodically lowered into cold water.

First, marking is applied to the sheet, then all the tops of the waves are cut to a depth of 1.5 cm. After that, they turn over, cut the upper points of the depressions and turn off in the cut. The method is suitable for a small volume.

The electric jigsit cuts along the same principle as a hacksaw. The file is chosen on wood with large teeth, better from well.known manufacturers. Bosch, Makita. Since ondulin sticks on the canvas of an electrician faster, this tool is used less often.

Circular or saber.saw and angular grinding machine.

The best option for cutting a large volume according to experienced builders is a manual circular (disk) saw. It provides a perfectly even cut, quickly processes a large amount of material. It is better to choose a disk with the largest number of teeth. You can clean it from sticky particles by cutting a piece of wood. It is convenient to cut off the Euro.shifer and along and across. The disk is periodically recommended to lubricate with machine oil.

Less commonly used a saber saw instead of a disk. Both the circular and a saber tool can independently process several sheets at once. To do this, they are preliminarily fastened to a pack and aligned. The thickness depends on the diameter of the disk or the length of the file.

You can use a corner grinder (angular grinder) with the thinnest disk. Cut a corner grinding machine you need to very carefully. When working at high speeds, there is a great risk of melting edges.

  • When selecting color, it must be borne in mind that Euro.shifer is prone to fading in the sun.
  • The smaller the size and number of waves, the more overlaps between the elements of the roof, which means that the strength of the roof is higher.
  • If the installation is carried out by one person, then again it is better to choose sheets of the smallest dimensions and weight.
  • When buying, be sure to pay attention to the thickness. If it is less than 3 mm, then the material is poor.quality.

Classical. It has 10 waves 36 mm high, the step between them is about 95 mm, dimensions are 2000×950 mm. Most often used for decoration of flat and vaulted roofs.

Smart. From the classic ONDULINE SMART is characterized by the presence of markings for fasteners-grooves and a clever locking castle. It has slightly smaller dimensions. 1950×950 mm, thickness and number of waves. like usual. The weight of one element is about 6.3 kg. Smart Castle prevents the ingress of oblique rain or melt water. Especially suitable for decorating the roof of residential and public buildings.

DIY. Already classic, its dimensions are 2000×750 mm, the number of waves is 8. Standard thickness. 3 mm, weight. about 5 kg. often used in areas with difficult climatic conditions. This is due to the large number of overlaps between the sheets, due to which the roof is stronger.

Compact. Has the smallest dimensions. 1000×750 mm. Thickness. 2.6 mm, weight. 2.5 kg, number of waves. 8. Suitable for finishing the roof of a small area or complex shape. Due to the largest number of overflows, less thickness is compensated.