How to cut mirror tiles from Ikea. Varieties of glass cutters

How to cut mirror tiles

Please, tell me which glass cutter is cut (ordinary diamond, oil) and on which side of Amalgam or Glass?

I honestly admit: the glass cutter in my hands held once and only in order to remove it in place. But I want to learn and I need your help.

Allisy wrote: But I want to learn and I need your help.

I cut the Irwin 2×2 with a tile.cutter without problems.

Thanks! The tool is called? If I say in the store: give me a tile cutter Irwin. They will not look at me with big eyes?

Without processing edges, the mirror layer from the water grades grades grades and takes on a sad look. Even if the seams are closed by grouting. You need pieces around the perimeter at least with oil varnish.

Allisy wrote: I ordered mirror pieces 20×20 cm (this is the smallest size), the thickness of the mirror 3 mm. Now you need to “poke” these pieces on the pieces, with a jet 2×2 cm.

It’s easier to choose a mosaic, and you are unlikely to cut it yourself

Allisy wrote: cutting the edge is not needed, pieces will be glued to the wall.

We need t.to.When operating, the grinding will be washed out (torture) and an acute edge will be exposed, which is fraught with injuries, and even in the process of laying you can also get hurt.

Allisy wrote: which glass cutter cut (ordinary diamond, oil)

Thank you very much that you responded and gave practical advice! I am aware that cutting mirrors or glass. This is a lesson requiring experience and knowledge. Perhaps I won’t succeed. from the first and even the tenth time. But I want to learn.

There are cut and sewing courses, but there are no glass courses. So in this matter, experience is acquired exclusively on its own. Well, good tips. Like a good teacher.

And you can cover the edges with epoxy resin? I also read on the Internet that there is an abrasive on the glass to get the edges of the edges. Such a thing does not need to get? As I understand it, after the abrasive, the edge still needs to be covered with something so that there is no access to moisture to the cut layer of amalgam. So?

Allisy wrote: And you can cover the edges with epoxy resin?

it is possible but not necessary, it is so gimoreno and if you can’t pull it to the surface, and you need to dry somewhere and this is about a day and the smell and so on.

Allisy wrote: There is an abrasive on the glass to get the edges

Any abrasive bar for sharpening knives will go and preferably with small grain (large grain can give chips) and with water. The most manufacturing will be the processing on the sandpaper with a diamond circle.

Allisy wrote: then after the abrasive the edge still needs to be covered with something so that there is no access to moisture to the cut layer of amalgam. So?

So, oil paint is suitable for this, but how then to sculpt it on the wall, here’s a question, because you wanted it like a tile for tile glue?

Size for an inexperienced cutter is small. Only Mother translate. Go to the nearest construction, to the tent where the glass is cut, and consider the glass. They will do anymore. PS. Just in case. glass cutting glass does not cut (like a knife sausage), but scratches. Then, on this scratch, glass is broken. here is the very ambush. If you really want to learn. practice on ordinary glass.

The mosaic will be located on a warm wall in the room. I’m not sure about tile glue. We will probably use something like liquid nails. And there is a glue that can damage Amalgam?

Regarding the translation of the material. I agree, but I can’t support this opinion. I want myself. For explanation of the intricacies of the process. Thanks. If I find glass in the house, I promise, first try it on it!

Allisy wrote: If I find glass in the house, I promise, first try on it!

Go to the market, there you are on a cheat, or maybe it will be for nothing to be given trimming, including mirrors, you need 2 by 2 cm, and they throw out stripes from large mirrors when they cut it if the stripes are already 15-10. By the way, there you can also ask you to cut such pieces, though I think it will get expensive, but you can a trial batch, see how they do it, how they are polished the edges.

Allisy wrote: I promise, first try on it!

Our person! Just put on old leather gloves when you break the glass.

Sansan21 wrote: Our man! Just put on old leather gloves when you break the glass.

Another valuable advice!Thanks! I wouldn’t think of.

Ilya87 wrote: go to the market, there you are on a deco, or maybe they will give out scraps, including mirrors, you need 2 to 2 cm, and they throw out stripes from large mirrors when they cut it, if the stripes are already 15- ten. By the way, there you can also ask you to cut such pieces, though I think it will get expensive, but you can a trial batch, see how they do it, how they are polished the edges.

Can I DIY rounded mirrors? (cutting glass at home) | WITHWENDY

I called markets and services. Some do not cut into such small pieces, others do not cut 3 mm mirror. 2 mm glass. Please, and a mirror. No. Regarding scraps there is also interesting. In some companies, there is simply no waste.free production and trimmings. Some say that they pass them somewhere and these scraps are worth some money. Roofing felts I did not go to these organizations, roofing felts on the market everything has changed a lot. They make the edge some kind of machine and do not polish manually. Thank you for the advice.

Alex_penza wrote: I can even say where to look

In the entrance? Or in the window? πŸ™‚ If your version is different from mine, please voice. πŸ™‚

How to make a hole in a mirror tile?

Sometimes you need to fix the mirror without using adhesive compounds. To do this, you need to make holes in it. The material is quite delicate and fragile, so you need to know how to drill, how to make a hole in a mirror tile so that it does not burst.

The hole in the mirror. reliable methods

How to work with any material with a mirror correctly. Often you need to make a hole, it can be a hole for a cord or dowel. Иногда отвСрстия Π΄Π΅Π»Π°ΡŽΡ‚ для Π²Ρ‹Π²ΠΎΠ΄Π° ΠΊΠΎΠΌΠΌΡƒΠ½ΠΈΠΊΠ°Ρ†ΠΈΠΉ, Π½Π°ΠΏΡ€ΠΈΠΌΠ΅Ρ€, софитов ΠΈΠ»ΠΈ Ρ€ΠΎΠ·Π΅Ρ‚ΠΊΠΈ. It is better to certainly order cutting glass or mirrors with us.

Advantages to order cuts of holes in Skelko:

  • Holes are made during the production of mirrors. When ordering mirror tiles, we make holes in it in those places where it is needed by your preliminary application.
  • The slots always look neat, made accurately and according to all technologies, without chips and damage.
  • We will accompany you with advice on all issues regarding mirror materials of their cutting and t.D.

Suddenly you miscalculated or forgot to warn about cutting holes, you can make them yourself, of course, it will take much more time and nerves and there is a risk of spoiling the product, so the ideal option is to order cutting of holes from us. If you have taken up the work themselves, you will need a special drill and a drill. Feather drill is taken for this purpose. They are made of a special alloy, can be of different sizes. You need to work with them slowly and accurately.

mirror, tiles, glass, cutters

Work process:

  • First of all, find a flat base to put a mirror on it, it should fit tightly, do not stagger.
  • Degrease the processed item, acetone or alcohol is suitable for this.
  • Measure and outline the center of the future hole.
  • When drilling, it is important to remember about cooling. You can fly around the place of the future opening fence from plasticine and pour water there, also a strippider works with an excellent coasten.
  • Fix the feather drill at the intended point and start drilling. Work a drill at low speeds, hold the drill evenly, do not make a strong onslaught.
  • Drilling a mirror is not done in one call. Here you need to stop every 5-7 seconds to avoid overheating of the mirror, otherwise there is a risk that it will burst. The drill does not break through, but gradually scraps the layers of the material, thereby forming a hole.
  • We drill the holes in the tile to the end, making a deepening to about half, turn it over and continue to drill to the meeting, from the back side.
  • Do not forget to use gloves and glasses when working. There is always a risk of getting a fragment.

You can make a hole of a large hole with a feather drill, if you need to make a hole of a larger diameter, then you need to use a round tubular drill (crown) with a diamond coating. Such a drill costs cheaply and is sold in a construction store, choosing a diameter.

Stages of working with the crown:

  • Take a piece of plywood and drill a hole on it the same as you want to see on the mirror.
  • Put a plywood template on a mirror tile and fix it.
  • Start drill, carry out manipulations with stops, let the glass cool, use water or turpentine.
  • Do not drill to the end, only half, then turn the product and repeat the process from the back.

How to make a hole in the mirror?

Urgently, you need to make a hole in the mirror, but there is no drill, drill or crowns, then you can use improvised objects.

Place the mirror out of the blue, degrease, pour a bunch of wet sand to the place of the future hole. Make a funnel with a thin object in the sand, its diameter should correspond to the size of the desired hole. Melt any easily smooth metal (tin, lead) with a burner and pour it into the funnel done. After cooling the metal, brush sand, and voila, everything is ready when you remove the frozen metal, you will see a flat finished hole.

The video clearly shows how to make a hole at home.

There are other methods. using glass cutter or wire, but there is always a very high risk that the mirror will burst. Therefore, we still recommend contacting us. We will carefully make a hole in the mirror panel if you need to place the decor elements or communication signs on it. We will cut the holes of the desired diameter for lighting devices if you are planning to make beautiful mirror ceilings. Skelko company is always your reliable assistant and conductor in the world of mirrors.

How to cut

If you know how to cut glass, then these skills are certainly useful when cutting a tile or ceramic tile, since these processes are inherently the same.

They differ only in how marking is made and what efforts you need to make when broken.

mirror, tiles, glass, cutters

It is not difficult to cut the tiles, but it will take some time to, as they say, “fill your hand”. To do this, you can use unnecessary pieces of tiles to develop or adopt to the effort that will be required for a specific material. Do not neglect the “little tricks” that every experienced master is in stock. In steps, the cutting process looks like this:

  • Prepare the desktop. It must have a flat and hard surface.
  • Put the tiles on the table face up. Using a ruler, apply a fishing line for a cutting trimmer with a marker. (Use water.based marker, then it will easily retire with water).
  • Along the drawn line, attach the ruler and draw a glass cutter along the tile from the far edge of the product in the direction of. Use the metal ruler as a guide and try to distribute the strength equally when pressing the cutting tool. The cut is ready!
  • We put a wooden block under a tile (along the cut line) and press on both sides. The tile is easily split into two halves at the site.
  • View the end line of the cutting line. If large chips are visible to them, then clean the edges of the tiles with sandpaper of medium or large fraction. This will give the details a complete view.

It is worth clarifying some important points:

  • Do not cut the tile material in advance, but do this in the laying process. With this option, a minimum amount of marriage of tile material will be obtained, since few people are able to accurately calculate the distance between the tiles.
  • Try to press with the same pressure evenly on the glass cutter during cutting. Remember that if you press stronger. the surface of the tiles will be covered with small cracks. And if you do not give it. the fishing line for the trimmer of the broken will come out with chips or even not to break through the line.
  • It is better not to use glass cutter if you need to make a slice less than 1 cm. A short piece of tiles can unevenly break during cutting and ruin the entire tile as a whole.
  • And now about “little trick”. Experienced tiles advise to soak the tile for 3-4 hours in simple water before cutting. After such “water procedures”, the tile material becomes more plastic, and this allows you to produce high.quality cutting.

The advantages and disadvantages of glass cutter

The undoubted advantage of cutting tiles or tiles is its financial availability, and, accordingly, the cost of tile work in general. Hand glass cutter of roller and oil types are silent and do not create dusting in the room, which is important for housing, where other tenants can be in addition to the master. Also, a hand tool is indispensable for figure cutting, in design solutions requiring extraordinary and exclusive.

Cons. with significant volumes of manual glass sores, ineffective. A separate item can be noted by cutting porcelain tiles or ceramic tiles for the floor. In such cases, a hand tool is extremely rare, since plates of such material have increased strength and thickness indicators.

Summing up previously what has been said, we come to the conclusion that the manual roller and diamond instrument has a meaning to use with a small scale of cladding and if you buy a more expensive professional tool. an angular grinder or a tile cutter, for a one.time cutting financially unprofitable.

Small nuances when working

Before starting work, you must first study general recommendations, and then the technology itself in stages already. This will prevent mirror damage, especially if there is no experience of communication with glass cutter.

What you need to know before taking up the mirror:

  • During operation, the tool lasts only at an angle of 90 degrees. A slight deviation of several degrees is allowed. The support for the location of the mirror should also be exactly.
  • You can never change the angle of inclination in the process. Otherwise, then it will not work to divide the cut parts exactly and neatly, they can break.
  • The cut is made in one exact, fast and continuous movement.
  • The force of pressing is prohibited to change. The exception is considered to process the edges, 5 mm up to the end of the glass should weaken the pressure, otherwise the windshielder can slip. Because of this, chips are formed.
  • You need to cut from the distant side towards yourself.
  • It is allowed to work only on the front side (where there is no amalgam. an alloy covering the back).
  • A good incision leaves a dark trace on the glass. If when working with a roller instrument it came out whitish, then the incision can only remain on the surface.
  • When working with diamond glass cutter, a white strip always remains.
  • If you need to get an even cut, use a thick ruler. To avoid sliding, you can put pieces of rubber under it on both sides (use segments from bicycle tires).
mirror, tiles, glass, cutters

Reference. You can not try to deepen the incision that turned out to be bad. It is difficult to get into the same fishing line for a trimmer, repeated manipulations will lead to mirror damage (or you have to cut out a smaller part from it).

How to cut it correctly: step.by.step instructions

For an unprepared person, it seems to be a very difficult occupation, especially doing this not in a specialized workshop, but in simple home conditions. But if you know a clear sequence of actions, be careful, observe precautions, and not rush, the result will not disappoint.

  • A fabric is creeping on the table, which is able to protect the mirror when pressing it during cutting.
  • The mirror is cleaned first using a solution of soda, and then with alcohol. If you work with a dirty surface, dust and fat particles from the hands can shift the glass cutter, and the pieces will turn out uneven. This is especially true for the roller device.
  • A fishing line for a trimmer for a cut is applied. It is necessary to ensure that it is located next to the site of the glass cutter (is located 2 mm from the desired point).
  • You need to make sure that the tool is perfectly sharpened, otherwise the glass will crack unevenly.
  • An incision is made on the recommendations described above.
  • This stage is one of the most important. It is necessary to observe special accuracy when performing it. The mirror is put on the edge of the table so that the fishing line for the trimmer of the cut protrudes slightly. It is pressed to the surface with the left hand, and the right is the broken movement down the right. The break should be done in the opposite direction from the cut. If the breakdown movements did not bring results, you can use a hammer. They should be tapped along the marked line on the lower side of the mirror, acting from the far edge.
  • If the thickness of the site that needs to be broken off is too small for capture, you can clamp it using glass cutter grooves. It is also allowed to use plugs with rubber tips (or winding from island).
  • The resulting sections must be reliably fucked with fine sandpaper (from 160 to 1,400 abrasive particles per square inch).

Important! Beginners cannot immediately start work without proper preparation. First you should train on cutting small mirror elements, and then proceed to the main part.

It is not necessary to involve professionals in the process of cutting mirrors for decorating a room at all, you can easily learn to use the glass cutter yourself. This activity seems difficult only at the very beginning. You can cut the mirror if it does not differ in an unusual shape with complex bends. No need to be afraid to pick up glass cutter! After a pair of training, a flat fishing line for a trimmer will definitely get.

DIY mirror tile laying

Category: Repair ceiling Special materials: 2012-07-01 17: 30: 17 Zzerkal tile is a type of ceramic tile. At its core, it is a mirror glass, which means that you need to work with it accordingly. It is worth noting that laying mirror tiles with your own hands differs from the installation of ordinary ceramic glazed tiles. Particularly great difficulties arise with a sharp material. To cut the usual tiles, an angular grinder is used with a special disk or tile cutter. However, tiles do not allow special cuts in the tile. In this case, the material may simply break.

For complex cuts of tiles, the most suitable tool is an angular grinder. However, when using it, the edges of the material are beaten off, as a result, damaged places are striking. Therefore, it is better to combine the advantages of angular grinding and tile cutter, using both of these tools. When laying mirror tiles with your own hands, there will certainly be a need to cut it.

Using a tile cutter, put a flat object under a mirror tile, which will bring it closer to the blade of the knife. To perform this operation, you will have to adopt. Until you learn how to cut the tiles, maybe several saws will have to be broken. Do not be upset. this is a common thing. The mirror tile is best cut using glass cutter, and diamond glass cutter will be the most optimal solution. It will cut the tiles like ordinary glass.

ВСхнология ΡƒΠΊΠ»Π°Π΄ΠΊΠΈ Π·Π΅Ρ€ΠΊΠ°Π»ΡŒΠ½ΠΎΠΉ ΠΏΠ»ΠΈΡ‚ΠΊΠΈ

How to lay mirror tiles? Like ordinary tiles. First achieve an absolutely flat surface and apply tile glue or sealant on it. Experts recommend using 25-kilogram bags with this glue. One such bag is enough for approximately 3 square meters of coating.

Tile glue is a convenient and effective adhesive mixture, which is not affected by neither fungus, nor water, nor frost. Apply such glue on a wall with a layer of 0.5-1 centimeter over the entire size of the tiles. After that, the excess solution is removed by a gear spatula, forming a wave.shaped layer of glue. This masonry method will give additional strength to the coating, since thanks to the wave layer, the effect of adhesion is created. Even when the tile does not completely dry, it will be extremely difficult to tear off the wall.

Set plastic crosses between neighboring elements. The size of the crosses must correspond to the gaps between the tiles. On sale you will find crosses for tiles 0.1-1 centimeter. When choosing them, it is important to take into account the design of the entire room, since the thickness of the seams will immediately catch the eye. If it is excessively thick, then the mirror image will be broken into separate pictures, and the seam with a very small thickness will make it difficult to align between individual tiles if their walls are very uneven.

ΠœΠΎΠ½Ρ‚Π°ΠΆ Π·Π΅Ρ€ΠΊΠ°Π»ΡŒΠ½ΠΎΠΉ ΠΏΠ»ΠΈΡ‚ΠΊΠΈ Π½Π°ΠΏΠΎΠΌΠΈΠ½Π°Π΅Ρ‚ ΡƒΠΊΠ»Π°Π΄ΠΊΡƒ кСрамичСской

The procedure for installing mirror tiles is the same as when laying a ceramic. However, it is important to remember that we work with glass, which means that the shrinkage of the elements with a rubber hammer should be performed more carefully, otherwise you will simply break it. You can wipe the seams with ordinary grout, however, when working in the bathroom and grout, and glue should be moisture resistant. You can use one sealant. Its main advantage is that over time it will become rubber and will not miss moisture to the edges of the coating.

Some believe that mirror tiles do not resist the humid environment well enough and deteriorates over time. But its manufacturers convincingly assure that mirror tiles are resistant to moisture. And it seems reasonable that the mirror of good quality is not terrible.

If you are afraid that over time it will darken from the mirror, then use tile glue for its installation, but natural sealant. However, in this case, the styling technology will change somewhat: the tile will be glued to the wall. Any bumps that may occur can be eliminated by adjusting the thickness of the layer.

The construction portal about the repair of the Allomormal for and the entire site is intended for those who planned to make repairs with their own hands.

Colored mirror ceiling tiles colored glass glass mirror mosaic Glass tiles for ceiling

Bathroom smart mirror glass living room decorative wall mirror glass

High quality glass mirror is made of Vatti Glass glass with a high-quality transparent or tinted float glass. Our high.quality coatings can be made pleasant to the touch of mirrors with a high reflection. The surface of the mirror is clean and bright, which gives a clear and living image.

Features: 1) Mirrors are available in silver or aluminum design and are suitable for any atmospheric conditions. 2) the mirror surface is clean and bright, which gives a clear and realistic image. 3) The galvanic layer is hard and adhesion, and the protective layer is impregnated with good erosion resistance. Types of mirrors: silver mirror, aluminum mirror, mirror without copper and lead, security mirror, solar mirror, mirror with a beveled edge, etc. D. Glass color: transparent, transparent, bronze, euro-gray, dark blue, blue, dark green, light green, etc. Color of the posterior paint: gray, blue, green, white, etc. D. Thickness: 1 mm, 2 mm, 3 mm, 4 mm, 5 mm and 6 mm, etc. D. Dimensions: 1524×2134 mm, 1830×1220 mm, 1830×2440 mm and 2134×33300 mm, 2250×3300 and t. D.

For which tiles the glass cutter is not suitable

You can cut a tile with a thickness of not more than 5 mm with a glass cutter with a high.quality. The use of any variety of this tool is not recommended for gypsum tiles with an uneven surface and ceramics with indicator p.E.I. (wear resistance class) more than 2. This is usually a floor tile and porcelain tile.

The ability to cut porcelain tile depends on the manufacturer. Chinese products can be defeated using an oil or diamond instrument.

In other cases, it is recommended to rent or purchase a tile cutter. The following types of tools are produced:

  • Plump-wire tiles connects the functions of roller glass cutter and forceps. First, the groove is drawn on the surface, it remains only to cut the tiles, breaking it off with forceps.
  • The mechanical consists of a cutting roller and an emphasis on which the cut material is broken.
  • Electric is an electric saw that cuts the tile. Instead of this type of tile cutter, you can use a corner grinder, which is often in a home workshop. The angle grinding machine will help out if necessary to cut a ceramic fragment along the curve line.

Nuances and recommendations of masters

Knowing some subtleties will facilitate the process of cutting tiles. The recommendations of masters will also play a positive role in performing this type of work.

  • Models with wooden handles are more convenient: they are easier to keep motionless.
  • To obtain initial work skills, you should sacrifice a couple of pieces of tile and cut them into parts of all kinds.
  • The first and last approximately 5 mm are carried out with less pressure. Otherwise, you can break pieces of ceramics.
  • If during the creation of the groove the glass cutter came off the surface, you need to retreat 2-3 mm and continue the fishing line for the trimmer.
  • If necessary, cut the parts of a large thickness should draw a recess from the face and from the inside.
  • The cut element must be thoroughly cleaned of dust. Any pollution can change the glass cutter path, and the fishing line for the broken fault will turn out to be a curve.
  • A lubricating liquid is poured into the oil tool on 2/3 of the container. If it is supposed to cut one or two pieces, you can just dip the cutter into grease. Machine or sunflower oil should not be used for this purpose: it will not go to the working part due to a large viscosity.

How to cut mirror tiles

For high.quality cutting mirror tiles, the choice of diamond glass cutter will be optimal. This is due to the fact that the facing material in structure is close to glass.

Many masters prefer to use oil windows with kerosene as a lubricant. Step.by.step instructions do not differ from actions when cutting tiles. The material is broken by combining the resulting groove with the edge of the table. The movement should be sharp and applied to the middle of the cut fragment.

Mirror tiles with fatcet is ideally not cut. It is selected so that the details are laid on the desired surface in its entirety.

Features of cutting glass cutter

Of course, to cut the tiles, it is not necessary to use glass cutter, the following tools may help you:

But what to do if there is nothing but the aforementioned glass cutter?

Important! You need to understand that it will not work out with the help of glass cutter from the tiles of 5 mm, you will take a tile at a “fragment” at a certain moment, and this is difficult to do when you need to separate only 5 mm and less.

Further. in general, you must first figure out whether it is possible to cut your tile with glass cutter. It used to be without problems, and now manufacturers produce so much ceramic tiles, which will be difficult to cut out even in the presence of manual tile cutter, and what can we say about the glass cutter! Therefore, it will not be superfluous to train on broken tiles. in general, will your tile take your chosen tool?

What rules do you need to know about laying mirror tiles

Repair

How to Cut a Mirror

Mirror tiles appeared not so long ago in the arsenal of designers and finishes, but has already won a well.deserved popularity. Unlike ceramic tiles, the mirror is made of glass, so its laying requires caution and compliance with some rules. In general, the methods of laying mirror and ordinary tiles are largely similar.

The main difference between the process of laying mirror tiles from ceramic material is the use of other adhesive compounds and methods of cutting. Conventional adhesive mixtures for ceramics are made on a cement basis, from the effects of which the reflective layer of the mirror is destroyed. Therefore, special adhesive pastes are used for mirrors. All of them are designed for safe use on a mirror surface, as they are made of synthetic resin and rubber. Produced in the form of cartridges for mounting pistols.

Cut mirror tiles in a special way. To do this, you can not use tile cutter. Since mirror tiles are ordinary glass, you need a metal ruler, glass cutter and glass skills.

Before laying mirror tiles, it is necessary to carefully prepare the surface. It should be perfectly flat, since defects will appear after tile sticker. To do this, peeling paint or plaster is removed with a spatula, all the ledges are knocked down, and the depressions are put off. Then check the surface plane. It is cleaned with sandpaper for grinding finish plaster. After, treated with two layers of penetrating primer. This will reduce the porosity of the surface and increase its adhesion with adhesive composition. In rooms having increased humidity (bathrooms, bathrooms), the walls must be additionally treated with antiseptic compounds to prevent mold formation.

Starting styling, the surface of the wall is marked with a marker. The glue is applied with a snake or dots on the back of the mirror tile, using a mounting pistol. After a two.minute exposure, tiles are applied to the wall and slightly pressed. It is important to observe the thermal gap between neighboring tiles, it should be no more than 2 mm. For convenience, you can use crosses. Laying is done from the bottom up, according to the marking. If the glue is too fluid, you can prevent tiles with a masking tape glued to a neighboring tile.

A few hours after the curing of the glue, the tiles are freed from the crosses, adhesive tape and the seams are grouted. The same glue is suitable for this. Its excess is immediately removed from the surface of the tile with a spatula or sponge.

Safety precautions when cutting mirrors

Cutting mirrors, like any other production type of activity, poses a significant threat to human health with a careless attitude to it and violation of safety precautions. The main threat is the fragments of glass that can crash into the hands of the master, get into the eyes.

General safety requirements for cutting glass are as follows:

  • Prior to the start of work, protective glasses and gloves are put on. It is important that glasses should not reduce visibility. Gloves are better to take rubberized.
  • Provide a special screening box so that they are not in the working area and are not scattered on the floor.
  • The waste from the box is taken carefully, it is better to finish the cracked pieces and get out in parts.
  • For cutting a mirror, you need a normal table. Using a workplace collected from improvised things can lead to unpleasant consequences.
  • After work, the countertop wipes, and the floor around the workplace is thoroughly sweeping.
  • Cut glass should be in compliance with all aspects of technology. Innovations are unacceptable from themselves.

How to use glass cutter correctly

To get a beautiful and high.quality cut of the mirror, you need to adhere to the following recommendations:

  • First, the serviceability of the tool is checked. In roller glass cutters, the disk should not hang out in different directions. In models with a diamond cutter, sharpening looks, if necessary, the location of the stone is adjusted. It is advisable to make training cutting on an unnecessary piece of glass.
  • The surface of the glass is prepared for work, it is cleaned and degreased.
  • If one of the glass surfaces has some kind of texture, such as a colored pattern or reflecting film, cuts from the opposite side.
  • It is necessary to press the glass cutter with constant force throughout the entire cut, the pressure only weakens a little at the edges of the mirror. The angle of inclination of the tool during operation also does not change. The force with which is pressed on diamond glass cutter is less than on the roller.
  • The tool is customary to keep as follows. In the hand, the glass cutter is clamped by the thumb and middle fingers, the index presses the header’s head.
  • Well.sharpened glass cutter, with proper operation, does not make creaks and leaves a thin, slightly weak thing. Whiteness and microcracks speak of poor.quality crushes.
  • If the incision came out of poor quality, the master retreats several millimeters and begins a new cut, without trying to fix the previous one.
  • Glass cutter is led strictly from the far end to themselves.

Independent work with mirrors, perhaps not only will help to master the glass cutter, but will also be able to arouse in a person an internal designer.