How to cut the ceiling plinth correctly. Conclusion

How to cut the ceiling plinth correctly

If you are going to cut the angles of the plinth in the room, then you need to start work with the purchase of. This makes it possible to choose the required angle for operation with a mounting knife or spatula, the dimensions of which will depend on the front of the work performed. For installation of plastic structure, work with a stupid with low tilts up to 90 ° is quite suitable. Most likely the most complex stage is the docking of all the used elements in such a way as to exclude the appearance of the cracks. At this time you will have to develop a sketch. The skirting board is located right on the wall itself. If there is no time in the set of your tools at the moment, then the use of a stencil is quite applicable.

Polyurethane skirting boards are the most expensive products. The high cost is determined by a large number of advantages, among which. Excellent resistance to moisture, high mechanical strength, reliability and elasticity. For most situations, this option will be optimal.

However, there are exceptions. Polyurethane does not withstand temperature extremes. If you place such skirting boards in the kitchen in the area of ​​the stove, then over time the polyurethane is deformed and crack. The cutting of such fillets is performed by a special knife, and no complications in the process of work arise.

How to properly cut a ceiling plinth with the help of a little?

What is knocking? This is a special tool that looks like a tray with slots. The grooves are designed for clear cutting of corners on bars, rails and other elements. Standardly, the knock has stencils of such corners as 45, 60, 67.5, 90 degrees.

How to saw off a ceiling skirting board for the outer corner? In order to cut it off, it is necessary to put the skirting board in the knock on the side from which the element will be fixed on the ceiling. Thus, the ceiling baguette is applied to the near wall. After that, the gutter, which has a tilt of 45 degrees, cut the baseboard itself.

A filler is applied by the lower part to the top. Thus, we will see the element in the angle in which it is attached to the ceiling. Do not forget that the lower point of the cut will border on the angle of the wall, that is, it will be the extreme point of the profile.

In order to cut the left skirting board of the outer corner, the hacksaw is placed from left to right, and for the skirting board on the right, on the contrary, from right to left.

But what to do to cut off the inner corner of the left skirting board? In this case, the lower extreme point of the element will perform, so the left filler is cut from right to left, and the right. From left to right (read: “How to cut off the ceiling plinth is useful to know”). Thanks to this, we get the inner angle.

Curlers cuts on ceiling skirting boards

There are three main methods of cutting angles on the skirting board:

We do not consider the “by eye” method, although it is used quite often, but, nevertheless, such actions almost never give accurate results even among experienced masters (see. How to fix the ceiling plinth. Step.By.Step instructions).

With the help of the stir

• The carpentry is a device in the form of a tray with grooves for a hacksaw and is designed to accurately cut off the corners on the boards of rails and bars. Standard knock has a stencil of angles 45⁰, 60⁰, 67.5⁰ and 90⁰.

Wallowing the outer corner of the left skirting board

• In order to make a cut for the outer corner of the ceiling baseboard, you need to put the profile in the knock on the side from which the skirting board will be fixed on the ceiling. We put the cornice to the wall near us, because we do this not for the floor, but for the ceiling. We find an angle of 45⁰ in the gut and cut off an extra piece.

• The ceiling plinth is applied by the lower part upward, and when we look at it from top to bottom, we will see the profile in the perspective in which it will be on the ceiling (see. The joint of the wall and the ceiling: how to choose the right ceiling plinth). Take into account that the lower point of the cut (in the stizl is the upper one) will be bordered on the angle of the wall, therefore, this will be the near extreme point from the beginning of the profile. To saw off the left skirting board on the outer corner of the hacksaw, we have a hacksaw from left to right, and for the right skirting board. Vice versa.

Wallowing the inner corner of the left skirting board

• Now let’s figure out how to saw off the skirting board for the inner corner. The lower extreme point of the profile (in the stizl upper) will be, therefore, the left skirting board must be sawn away from right to left, and the right one. From left to right to the right to the right. Thus, we get the inner angle.

Using a drawing on the table

Imitation struck using the drawing on the table

• And how to cut a ceiling plinth if you do not have a carpentry? You can bypass the drawing on the table that will imitate this carpentry device (see. How to cut a ceiling baseboard correctly: step.By.Step instructions from real masters of their craft). We make two parallel lines on the table at a distance, which has the inside of the gutter in the standard stuplet. 85mm.

• Now among these lines we find a square and draw two diagonals in it, as shown in the figure. Thus, we get an imitation of struck, with angles of 45⁰.

Wallowing the inner corner of the left skirting board on the table

• All further operations are carried out in the same way as in Stusl, only instead of pressing the baseboard to the side, we put it along the line. Keep in mind that the skirting board cannot lie directly on the line, so you need to orientate visually or put some kind of square item (box) to the line to get the side.

• Do not forget that when cutting the bottom of the baseboard on the ceiling will be at the top and vice versa. For the inner angle, the lower corner of the profile will be protruding, and the upper part of the plinth will perform for the outer corner.

Using marking on the ceiling

Plinking ceiling marking

• But how to saw plinths if the corners in the room do not have 90⁰? This is quite common, especially in the private sector. For this, too, you will need to make a small drawing.
• The skirting board is applied to the angle of the ceiling and walls necessary for us, and a line is drawn along the ceiling. We do the same operation on the other side of the corner. Now that we are applying a baseboard, one of the lines crosses it (see the photo).

• The intersection point and the lower angle of the baseboard will serve as a cut line. The angle of cut from the outer part to the internal should be approximately 45⁰.

• In order to cut off the outer angle, it is necessary to make the same drawing. Only this time the protruding will be the upper part of the baseboard.

Skirting board on the floor

All that we disassembled relative to the ceiling baseboard can be used to install the skirting board on the floor. You have to change only the side of pressing the profile to the side of the breeze. That is, if for the cut of corners for the ceiling we are pressing against the nearcine, then for the floor we need to FOCUS on the far side or line. Everything else does not change.

If we draw the corners right on the floor, then everything remains as before, we will only look at our work not from the bottom up, but from top to bottom. A wooden skirting board for the floor, of course, is not used very often now, but a profile of good wood will never lose relevance. Therefore, the ability to make a clear cut for docking will always be necessary.

Curlers cuts on ceiling skirting boards

There are three main methods of cutting angles on the skirting board:

We do not consider the “by eye” method, although it is used quite often, but, nevertheless, such actions almost never give accurate results even among experienced masters (see. How to fix the ceiling plinth. Step.By.Step instructions).

With the help of the stir

• The carpentry is a device in the form of a tray with grooves for a hacksaw and is designed to accurately cut off the corners on the boards of rails and bars. Standard knock has a stencil of angles 45⁰, 60⁰, 67.5⁰ and 90⁰.

Wallowing the outer corner of the left skirting board

• In order to make a cut for the outer corner of the ceiling baseboard, you need to put the profile in the knock on the side from which the skirting board will be fixed on the ceiling. We put the cornice to the wall near us, because we do this not for the floor, but for the ceiling. We find an angle of 45⁰ in the gut and cut off an extra piece.

• The ceiling plinth is applied by the lower part upward, and when we look at it from top to bottom, we will see the profile in the perspective in which it will be on the ceiling (see. The joint of the wall and the ceiling: how to choose the right ceiling plinth). Take into account that the lower point of the cut (in the stizl is the upper one) will be bordered on the angle of the wall, therefore, this will be the near extreme point from the beginning of the profile. To saw off the left skirting board on the outer corner of the hacksaw, we have a hacksaw from left to right, and for the right skirting board. Vice versa.

Wallowing the inner corner of the left skirting board

• Now let’s figure out how to saw off the skirting board for the inner corner. The lower extreme point of the profile (in the stizl upper) will be, therefore, the left skirting board must be sawn away from right to left, and the right one. From left to right to the right to the right. Thus, we get the inner angle.

Using a drawing on the table

Imitation struck using the drawing on the table

• And how to cut a ceiling plinth if you do not have a carpentry? You can bypass the drawing on the table that will imitate this carpentry device (see. How to cut a ceiling baseboard correctly: step.By.Step instructions from real masters of their craft). We make two parallel lines on the table at a distance, which has the inside of the gutter in the standard stuplet. 85mm.

• Now among these lines we find a square and draw two diagonals in it, as shown in the figure. Thus, we get an imitation of struck, with angles of 45⁰.

Wallowing the inner corner of the left skirting board on the table

• All further operations are carried out in the same way as in Stusl, only instead of pressing the baseboard to the side, we put it along the line. Keep in mind that the skirting board cannot lie directly on the line, so you need to orientate visually or put some kind of square item (box) to the line to get the side.

• Do not forget that when cutting the bottom of the baseboard on the ceiling will be at the top and vice versa. For the inner angle, the lower corner of the profile will be protruding, and the upper part of the plinth will perform for the outer corner.

Using marking on the ceiling

Plinking ceiling marking

• But how to saw plinths if the corners in the room do not have 90⁰? This is quite common, especially in the private sector. For this, too, you will need to make a small drawing.
• The skirting board is applied to the angle of the ceiling and walls necessary for us, and a line is drawn along the ceiling. We do the same operation on the other side of the corner. Now that we are applying a baseboard, one of the lines crosses it (see the photo).

• The intersection point and the lower angle of the baseboard will serve as a cut line. The angle of cut from the outer part to the internal should be approximately 45⁰.

• In order to cut off the outer angle, it is necessary to make the same drawing. Only this time the protruding will be the upper part of the baseboard.

Skirting board on the floor

All that we disassembled relative to the ceiling baseboard can be used to install the skirting board on the floor. You have to change only the side of pressing the profile to the side of the breeze. That is, if for the cut of corners for the ceiling we are pressing against the nearcine, then for the floor we need to FOCUS on the far side or line. Everything else does not change.

If we draw the corners right on the floor, then everything remains as before, we will only look at our work not from the bottom up, but from top to bottom. A wooden skirting board for the floor, of course, is not used very often now, but a profile of good wood will never lose relevance. Therefore, the ability to make a clear cut for docking will always be necessary.

How to cut a plinth with a little

Fetling is a trihedral box of wood, metal or plastic, in the two vertical faces of which through the through slots are made, located at an angle of 90 and 45 degrees (see. The joint of the wall and the ceiling: how to choose the right ceiling plinth). With the help of a cuset, a ceiling skirting board is easily prompted to dock straight sections and design the right straight angles.

Internal angles

In the standard rectangular room, all corners are internal. The plinth sticker begins precisely with them, so that you can not pay attention to fitting along the length.

Correct installation of a ceiling baseboard

• To trim the left corner, set the baseboard in the knock so that its long part is to the left of you, and the one that you will cut is in the very fast, with a slight entry on the right slot of 45 degrees (see. Foam ceiling cornices: cheap, angry, and also very beautiful).
• That part of the skirting board that will glue to the ceiling, press the bottom of the bottom, and the one to the wall. Press the side wall to the closest side to you.
• Holding the skirting board tightly in this position, cut the corner with a hacksaw or a construction knife through a slot.

How to cut the ceiling skirting board for the left side of the inner angle

Cutting the corners of both skirting boards, press them into a corner without glue to make sure that the cuts coincide. If this is not the case, then trim them with a construction knife. After that, the plinth can be glued.

External angles

External corners are found in rooms with internal protrusions or niches (see. How to make the angle of ceiling plinth: recommendations from masters). If you do not know how to correctly cut the ceiling skirting boards in this case, then we hasten to reassure you. This is done in the same way as in the previous case, with the only difference being that the left skirting board is cut through the left, and not the right slot of. That is, from a different angle.

As a result, the part of the skirting board that will adjoin the ceiling will turn out longer.

We act similarly with the right skirting board: we put it in the knock on the right, clutching to the bottom and side wall, and cut it through the right slot.

Materials for ceiling skirting boards

Ceiling baguettes can be of various widths, have a convex pattern on the front side and special recesses for engineering systems from the back. The fillets are made in specialized production from foam, its varieties. Polystyrene foam, polyurethane and wood.

Styrofoam. The most affordable finishing material. Its positive qualities: light weight, simplicity in cutting and processing, the possibility of finishing by painting in any color. Negative moment. Granularity and low strength. Even slight mechanical damage can disrupt the integrity of the foam surface.

Foam polystyrene. A more durable variety of foam. It is also light in weight and in processing, but has a greater density and smooth surface, more resistant to mechanical damage, is good to stain. Due to their slight weight, these two materials have a slight load on the load.Bearing walls.

Wood. The hardest and most impact.Resistant of all the materials going for the manufacture of fillets. Products from it retain the appearance longer and are able to withstand a significant mechanical effect. In the style of some interiors, it is the most applicable wooden friezes. The tree ennobles the room and fills it with warmth. However, it has a higher price than previous materials.

Foam products, as well as polystyrene foam, have an advantage compared to wood. The softness of the material makes it possible to press the baguette to the wall, ceiling and to each other as much as possible. So there are no gaps left. It is possible to achieve excellent joint of the baseboard on not perfectly even walls if you use not wide foam or polystyrene foam.

Ready.Made corner elements

In order not to trim the ceiling skirting boards yourself, you can use ready.Made solutions. In any construction store you can find factory products, already at the factory made at a certain angle. Such an angular element allows you to combine the edges of the plinth, simply cut off at a right angle. Corner details allow not only to connect a filler in the corner of the ceiling, but also to hide the defects of the cut at the edges of the parts.

Unfortunately, this method is not relevant in all situations. The dimensions of the angles produced at the factory are adjusted to certain standards. But the skirting boards themselves are far from always complying with the standards. Of course, such details can be combined, but the result will look unaesthetic. If there are no angles of the right size on sale, then you still have to engage in pruning skirting boards on your own.

Choosing material and measurements

First you need to measure the room where the baseboard will be installed. All measurements are sure to write down so as not to forget and not get confused. It is recommended to draw a room scheme. About ten centimeters are added to each segment. You can also use the online calculator, which will simplify the task.

When choosing a plinth, it is worth considering the following:

In addition to the skirting board, you will need materials for its fastening. Fastening materials are usually selected depending on the wall of the room. If they are faced with drywall, then the skirting board can simply be glued. It is better to fix it to the brick with nails, to panel or block walls. Screws. By the way, plastic skirting boards on the website of the company “Nek” are already sold with fasteners. This is very convenient.

Before the cutting process, marking the roulette. Note which piece of skirting boards will be in one part or another of the room. It is worth using the skirting board economically, otherwise there will be a lot of small unnecessary pieces. They will only have to be thrown away. Drain the baseboard both in the corners and places of joints. It is recommended to cut a cut with a circular saw, installing it on a flat surface. If this is not possible, a wood hacksaw is suitable.

If the room is not straight, then the 45-degree cut, unfortunately, will not work. Here you have to resort to the help of specialists: to determine the angle of the saw will be troublesome for an ignorant person. It will take a knock and at least the slightest understanding of how to work with a tool.

Using a pencil and ruler, draw a cut line (angle of 45 degrees), then the material is cut. For plastic, a scabbard for metal is perfect, due to this, the cut will turn out to be smooth, even. Due to this and the final result will look very neat. The foam rail can be cut with a sharp knife, and gypsum plastic boards are sawn as plastic.

Detailed instructions on how to choose by color, cut a plinth, paint, as well as everything you need, including the ceiling or floor skirting boards of good quality, look for TD-neko.Ru.

Impromptu tray-growing with your own hands

To make a knock with your own hands is also not difficult.

Method 1. Three wooden strips or boards will be needed, which must be put together in the P-shaped box. Then, the necessary corners are planned on the walls of the box, and a cut. The result should be a wooden knock in which the grooves are cut out.

ZOOM H1 о чём все молчат ? Сравнение с Olympus 712 PC

Method 2. Combination of impromptu navigated and template with intended lines. For the convenience of cutting, it is necessary to build something that it will be convenient to hold the bar of the ceiling plinth, since it is difficult to keep it on weight. It is enough to put on two wooden planks or boards corner. On paper, you need to draw lines with angles for cutting at 45 degrees or under any other. Then we attach the plinth to the corner, press it with the hand, as described in the technology of use of the stir, we move a piece of paper with the template to the edge where we are going to perform a cut and cut off. In the process of cutting, we FOCUS on the line drawn on paper.

Method 3. As an impromptu, you can use anything you want, everything is that we form an angle. For example, a table moved to the wall.

Do not consolidate the planks of ceiling skirting boards before cutting the response bar and tried on their location. Only after the two response planks perfectly converged in the corner, you can begin to fix them to the ceiling. Small flaws can be finalized with a file or a file in the case of wooden and polyurethane skirting boards. To fit the foam products will have to be wielded with a sharp knife.

If suddenly, even after fitting the skirting boards between them, a small gap remains, do not despair, it can be closed with a putty. Cutting a ceiling plinth yourself is not difficult. But in order not to spoil a lot of products, it is better to practice in small blanks first.

Review of the options and the process of ceiling finishing, choice of choice

Preparing the surface of the ceiling according to all the rules includes the following stages:

• All coatings are completely removed from the surface of the ceiling. Including plaster. After this stage, the ceiling is naked reinforced concrete slabs.

To build something, first you need to destroy something

• The surface is treated with an antiseptic primer. She will kill the resulting fungus and will interfere with the occurrence of mold in the future.
• After its drying, the line of penetrating primer comes. Its task is to create a layer with high adhesion to adhesives on the surface of concrete. In addition, the surface impregnated with a polymer solution will become stronger.
• Then all the recesses and cavities are diligently leveled with acrylic putty.
• Dried putty is re.Primed.
• And only after the primer dries can you move to the tile sticker actually. The same acrylic putty, liquid nails or universal polymer adhesives are used.

If you do everything according to the rules, the result will delight your eyes for a long time

Ways to cut skirting boards

There are several ways to cut a ceiling plinth:

Let’s first of all figure out how to use a stupid and what it is. A quest-special device that allows you to cut a plinth, both on a certain and an arbitrary angle.

Fetling allows you to form an arbitrary angle with linear accuracy, but in its use there are some nuances. The design of the device is uncomplicated, and the simplest option can be made manually.

How to cut a ceiling plinth with a bin

The elements of the skirting board should be located in stupidity exactly as it will be installed on the wall: we hold the top of the part, press the lower edge to the wall of the jacket. Cutting plastic skirting boards, it is best to use a hacksaw for metal. We cut the sawing carefully, excluding strong presses on the saw, as chips are possible.

To get a connection in the corners without a gap, it is important to choose the correct line of cutting, which will lead to an overexposure of the material.

How to make an even angle: methods

The most difficult thing is to cut the angle so as to get perfectly even: the surface of the materials used is not easy for cutting, in addition, you need to observe a good joining, preferably without huge cracks. How to make an angle on a ceiling plinth? You can use several ways: with a stupid, without a bin, with the use of decorative corners, as well as an alternative way.

Cut the corners of the ceiling skirting board without

How to cut a ceiling plinth without a bin? The work will require a well.Sharpened pencil, a small piece of skirting board, a stationery knife (for polystyrene or polyurethane) or a saw for metal (for other materials), a ruler.

It is necessary to attach a plinth to the corner and draw a line with a pencil along the outer edge, then attach to the other side of the corner and also note. As a result, on the ceiling you get a cross, the center of which will mark the place where the planks of the ceiling skirting boards should converge. Install the section of the baseboard to where you will glue it. Having rested on the wall with a end, transfer the desired mark to it. Thus, you can cut the corners of the ceiling skirting board without.

We make angles using

If the walls and angles in the room are smooth, for work you can use a knock. In order to correctly cut the angle correctly, a part in which a person will make a cut, then insert a saw into the guides. Thus, the part will be kept in place, and it can be cut off at the right angle. For high.Quality cutting of the baseboard, it should simultaneously fit to both surfaces, so it should be pressed against the wall. The ceiling plinth is pressed by the side that is closer to you.

With the help of the stir, you will need to cut an angle of 45 degrees. First you need to decide how to arrange a skirting board in a stupla. To avoid confusion and cut off correctly, place the right bar on the right, and the left on the left.

Perform work on the following instructions:

• The part of the struck that will be on the ceiling, press to the lower part. The second side will be raised and will be closer to you. It can be covered on the wall of the tool, and then it will not stagger when cutting.
• Determine the direction of the cut as shown in this figure and then cut the corner.

Attach it to the ceiling and check the geometry. If it is not even enough, it can be slightly fixed with a knife, and in the case of minor defects and wide gaps, you can use putty.

How to cut plinths using decorative corners

With the help of them you can easily and quickly get the necessary angles in skirting boards made of polystril or polyurethane. Install them on the ceiling, and then close the planks close to them. Cut them simply using a stationery knife.

How to make angles of a ceiling plinth without devices

• Make the necessary marks on skirting boards.
• Using the ruler, connect the edge of the plinth to the mark. If you just cut along the line, the parts in the corner are still not formed, as the inside will interfere. You can cut it later, making measurements on the ceiling.
• You can lay on the table the piece that should be cut, part that will be located on the ceiling, and cut off at an angle of 45 degrees. Adjustment will be required, but less.
• Repeat 2 and 3 points for the second bar, making the outer corner.

Thus, you can make a ceiling baseboard without special tools using improvised means.

What to do if the gaps remain?

If defects are found after completion of work, then few people will like the prospect of remaking it. In this case, it is easier to disguise them with one of the compositions. The best option for such processing will be the final acrylic putty. It has white and very plastic. The material is taken with fingers, then it is pressed into the remaining gap, carefully distributing it in the hole, yielding. The remaining composition is removed with a damp cloth. As a rule, there are no traces of imperfections at the joints.

How to cut a ceiling plinth? You need to stock up on the necessary tools and patience, since rush always provokes mistakes. The main thing in this case is the choice of the optimal way. But attentiveness and accuracy are no less important: skirting boards are made of not too strong material (exception. Wooden baguettes). They are fragile, so excessive efforts when working with such products are contraindicated.

How to cut off a baseboard for an angle different from 90 degrees

Many rooms can “boast” angles that do not correspond to 90 degrees. Such situations arise as a result of the shrinkage of the soil and directly the structure, as well as in case of violation of the technology of the construction of the walls.

In this case, the correct marking with the help of a bunker or drawing will not work, all actions are performed directly in place:

• Before cutting the corner of the ceiling plinth, it is applied to one of the walls and focused on the other wall.
• A line is drawn along the plinth.
• Similar actions are performed on another wall.
• At the intersection of two lines, a mark is made on one of the skirting boards, which is connected to the corner of the workpiece. They make an incision along this line.
• Repeat actions on another skirting board and try on both blanks. Make the necessary amendments.
• Plinths are glued in place, the joint in this case should be quite dense.

How the corners of the ceiling plinth are adjusted

Preparatory work

Before moving directly to work on the formation of angles, it is necessary to take some preliminary measures consisting of the organization of the workplace and the preparation of the necessary tools.

• Ruler, roulette, construction square, pencil.
• Augoter or transporter.
• Chancellery or construction knife with replaceable blades.
• Hacksaw with small teeth.
• Flow.
• Laser level. Desirable, but optional.

The knock is not an expensive complex device, so it can be purchased even if it is required for one repair. It will even be good if this tool complements the standard set of home workshop. Fetling is a kind of box, in the walls of which the guide cuts for cutting are made, made in both sides at an angle of 45, 60 and 90 degrees. The tool can be made of plastic or wood. In its bottom part, holes are often provided for attaching it to the workbench. To ensure immobility.

Ways to form angles

As a rule, ceiling skirting boards have a complex embossed surface. It is she who creates difficulties when forming from two of its segments of a right angle without leaving the gaps.

In addition, the corners in the premises of apartments and houses are quite often different from the straight lines, that is, from 90 degrees, which also complicates the adjustment of the skirting board. And it must be cut so that there are no gaps at the junction, otherwise they will spoil the appearance.

Another nuance that is important to consider when cutting the planks is the location of the corners. As you know, there are two of their types. Internal and external. Most often, only internal corners are present in the standard rooms of modern apartments. External corners are characteristic of rooms with one or more turns, for example, an entrance hall or a corridor, or in which there are niches or protrusions.

Trimming the baguette for the design of external and internal angles is slightly different among themselves.

Scheme of internal and external angles

There are several ways to achieve an ideal or almost perfect angular joint of the baseboard. In one of them you can use the stupid, in the other to use the laser level, thirdly. Marking using a square and ruler. The simplest of them is the first option, but its use is possible only if the neighboring walls of the room form an angle of 90 degrees.

Using the stir

Before starting work, you will have to monitor the perpendicularity of the walls in the corners to measure to make sure that it makes sense to cut the skirting board by the strules. Control is carried out using a large square or a special tool. An angular. Augoter is a professional tool, and not everyone has it, but you must have a square in your household.

Augoter. A device that allows you to accurately determine the size of the angle

If it turns out that the corners are still straight, or are not very different from the desired 90 degrees, then you can safely cut the strips at an angle of 45 degrees, laying them in the stupid. It will be better if the knock is pre.Fixed to the countertop. If you allow displacement during operation, then in the cut plinths serious errors may occur, entailing the inaccurate of the joint.

So that the skirting boards perfectly coincide with each other at an angle of 90 degrees, their edges should be cut in a mirror display at an angle of 45 degrees. They can be cut both separately and at the same time, a package.

• When choosing the second option, the strips must be folded together with the back side to each other, and then fix it in this position in several places with stripes of painting tape. If the skirting boards are not fastened, then when cutting a package of their displacement cannot be avoided.

• If the decision is made to cut each bar separately, then they are laid and cut alternately, but when cut, they are laid in the opposite direction. That is, one baguette is cut off on the left guide cuts of the stir, located at an angle of 45 degrees, and the second. On the right.

• The next step, two cut slices must be combined with each other. First, the check is carried out on the table, and then installation is carried out under the ceiling in the trimmed corner. Only by applying the baguette to the place of future installation can you see the real picture. If small errors occur, then the ends of the baguette segments should be adjusted using a sharp knife.
• Only after the strips are ashamed as much as possible, they can be fixed to glue.

As for the difference in the performance of cuts made using rushed for different types of angles (external and internal), it is well shown on the submitted schemes below.

Demonstration of examples of cutting cuttet using the internal and external angle of ceiling plinths

If you carefully study the schemes, you can see that the cuts are made from different sides of the edge of the baguette, that is, for the inner angle, the hacksaw is installed at an angle of 45 degrees from the main surface of the bar to its edge (if you look from top to bottom), and for the outer corner. On the contrary. On the contrary.

Making a bunker or template

If the corners in the room were even, but there is no stir at hand, then such a device or a simplified option. The template can be made independently. You can make it in several ways.

First option

If the knock is required for constant work, and there is no opportunity to purchase it for some reason at the moment, then you can make such a tool from plywood or well-processed board. For this purpose, you will need to prepare three wooden details. The walls should have a size of 500 × 100 × 15 and 500 × 80 × 15, and the bottom part is 500 × 200 × 20 mm. Different wall height will contribute to a more comfortable cut of details. A peculiar box without end walls will be assembled from the parts.

Pruning of the fillets

Pruning using

How to evenly cut the angle of ceiling plinths with its help?

The stall is called a simple tool that is used by carpenters. With it, you can cut any workpiece at the right angle.

It is usually a wooden, metal or plastic tray, on which are made for cutting at an angle of 45 ° and 90 ° special vertical slots.

There are complicated structures on which there is also a hole for the named corners for the implementation of a 60-degree cut.

For professional work, special knock is produced. Its rotary mechanism allows you to fix the cutting canvas in relation to the workpiece at any given angle.

Inner angle

The prepared baseboard is applied to the ceiling, the desired length is postponed.

Then this same bar is inserted into the knock exactly as it will be located on the ceiling. It must be pressed to the far wall of the device. In this position, the plinth is held with the left hand.

The hacksaw canvas should be in such a position so that its angle is 45 degrees, and the handle would get together as much as possible with the hand. Trying to avoid pressure on the saw, carefully cut the workpiece.

Next, in the skirting board, it is necessary to cut off the response bar. It is also placed at the far wall of the tool, holding and clinging, this time, with the right hand.

The position of the hacksaw similar to the previous procedure. Its handle comes closer to the hand with an angle of 45 degrees. The skirting board is cut.

Then ready.Made, already cut strips are combined. The accuracy of the fitting is checked. It is believed that for better orientation, in the manufacture of the inner angle, it is better to cut with the front part of the product. Places of cuts usually have to be adjusted with a file.

External angle

It is most correct in order to observe more accurately the dimensions, to begin to mark the inner angle again, and only after that go to the external.

Otherwise it may happen that along the entire length of the bar will not be enough.

The bar is applied to the ceiling, the size is made in size. Holding on his left hand, the ceiling baseboard is pressed against the closest wall, the knife handle gets closer to the hand. The workpiece is cut off.

The response bar is pressed against the nearest wall, while it holds it with the right hand. The canvas of the hacksaw should be at an angle of 45 °, the handle of the tool comes closer to the hand of the master. A piece of the workpiece is cut off, the angle is neatly joint.

Such processing by the edge of the parts using a wort is good in cases if the angle between the walls is even and straight (90 °).

If its indicators leave much to be desired, then you should use a different method.

Marking on the ceiling

The method with marking on the ceiling allows you to cut off the angle accurately and evenly. He has one drawback. The plinth bar is quite inconvenient to keep on weight during the procedure.

In all other ways, using this method, you will be able to outline the angle for cutting even more accurately than other.

Когда плинтус прикладывается к предполагаемому месту установки, все отклонения размеров и неточности заметны и сразу учитываются.

Cutting the angle

First you need to take a pair of workpieces, then cut them at right angles. Resting the end of the plank to the perpendicular wall, we apply one bar. We outline the line on the ceiling along the circuit of the skirting board. Remove the first bar, then also, resting the end of the end against the wall, we attach the bar of the response. In the same way, we mark the line on the contour.

The intersection point of two separate lines is a mark on which the workpiece is cut. Each bar is attached to the surface again, on both the point of the future cut is marked. From the found point to the other edge of the plinth plank, we draw the line. We cut the skirting boards according to the previously made outlines, carefully dock, place in the place of their installation.

This method allows you to more carefully process the internal angles.

How to make a template jarked with your own hands

If you do not have a point, it is not necessary to buy a tool for one.Time use. A template with similar functions can be done independently.

To do this, the desired angles of the cut are applied to wood, paper or cardboard.

Then you need to draw a couple of parallel lines, find the center, after which to measure the corners of any given size using the transporter.

This method is especially convenient in that, using it, you can postpone an angle of any size, even more than a direct.

The methodology for processing a skirting workpiece using a home.Made tool is practically no different from working with the original. The bar is pressed to one of the parallels, after which the hacksaw is installed at the required angle, and cut off.

Remember that before cutting the corners of the workpiece, you must definitely check the angle between the walls! To do this, use the transporter and corner.

How to make corners beautiful

When the fitting and installation of skirting boards around the perimeter is completed, it is necessary to close all the flaws in the corners with putty. For wooden skirting boards, you can use a wax pencil, or a special butter. After the repair composition is dry, a decorative finish layer is applied on top.

Before cutting a plastic skirting board, measure the distance and subtract 2-3 mm on each side so that the strips freely enter the docking parts

But the repair industry does not stand still, and today you can not suffer with a sharp and adjustment of the profile at the joints. So for polyurethane, polystyrene and plastic skirting boards on sale there is a special decorative connector that masks the corners and places of connection.

Polyurethane corner elements for ceiling skirting boards can not only hide the joints, but also noticeably transform the interior of the room. For floor plastic skirting boards, ready.Made angular parts and docking grounds are sold in the kit, during installation they are almost invisible.

We told in detail how to use the stupid and tinkle for cutting the profile, examined several ways to cut a ceiling skirting board, video and photographs selected for the article, clearly illustrate all the stages of the process. Before you glue the baseboard, prepare the surface, it should be even and dry, without dust. Having cut off the corner parts, be sure to check several times tightly to each other, if necessary, cut off again or finalize with an abrasive. If you are guided by the saying: measure seven times, cut one, then high.Quality and neat, without cracks and masses of putty at the joints, installation of skirting boards is guaranteed to you.