How to cut the corners of the skirting board for stretch ceilings

Preparatory process

Before gluing the skirting boards to the ceiling in the corners, you need to prepare the tools that will be needed when gluing the ceiling skirting board:

  • To calculate the required amount of materials, you need a tape measure.
  • It is recommended to fix the ceiling skirting boards with quick-drying glue or putty.
  • You can knead the adhesive in a previously prepared container, it is best to apply the putty with a spatula.
  • Remove excess glue or putty with a dry, clean cloth.
  • For cutting skirting boards at a certain angle, it is best to use a miter box.
  • Direct cutting of products is performed with a sharp construction knife or file.

corners, skirting, board, stretch

It is recommended to glue the ceiling plinth on a pre-filled and leveled wall. As for the wallpaper, they are glued after the fillets are installed. In this case, the fastening of the elements will be more durable. In addition, when gluing new wallpaper, there is no need to change the ceiling plinth, since wallpaper strips are glued along the lower edge of the fillet. Fixing over the wallpaper reduces the fixing strength of the skirting board and requires its dismantling when changing the finishing material for the walls.

The problem of how to properly glue the ceiling plinth in the corners is recommended to be solved using acrylic or silicone glue, characterized by fast drying, or on a construction putty. With the help of a putty, the skirting board is glued directly to the wall, the frieze is glued to the wallpaper using quick-drying glue. When using these materials for fixing products, there is no need to hold the elements for a long time to set the adhesive backing. In addition, with putty, you can simultaneously repair wall defects in the form of irregularities and cracks.

Using a thread or construction cord, it is necessary to draw a control line in accordance with the width of the frieze. In this case, you can count on a more even gluing of the ceiling plinth, and the process itself will not cause much trouble.

Main steps

Installation of a ceiling plinth cannot be called a difficult and time-consuming process; even a novice master can do it. However, for a high-quality work, you need to know all the details of installing ceiling plinths. When solving this issue, you should be especially careful about the design of the corners. Errors and shortcomings at this stage cause the formation of cracks and mismatches, which to a greater extent spoil the appearance of the entire ceiling. Therefore, the problem of how to glue the ceiling plinth in the corners can be called actual.

How to glue skirting boards to the ceiling in the corners. a step-by-step guide

When performing repair and finishing work, each stage should be treated responsibly. The final stage, when additional and decorative elements are mounted, requires special care. Most often they are in plain sight, so any mistake can spoil the appearance of the entire interior. Therefore, it is necessary to strive for the perfect execution of the final stages of repair and decoration.

The completion of any work on finishing the ceiling is the installation of ceiling skirting boards, which are called friezes or fillets. Thanks to this element, the transition between the ceiling and the wall becomes smooth, and the renovation takes on a complete look.

The main purpose of the ceiling plinth is to decorate the room, so you need to choose a fillet in accordance with the overall interior. In addition, this element allows you to mask minor defects at the junction of the ceiling and walls. Therefore, it is important to know how to glue fillets correctly.

Cutting skirting boards at an angle

The process of deciding how to glue a wide ceiling plinth always starts in one of the corners. Many manufacturers in the process of manufacturing products cut the skirting boards at a certain slope for easier decoration of the external and internal corners. The problem of fitting fillets with a complex pattern or pattern is especially urgent. When using a cornerless ceiling plinth, you can correctly and beautifully arrange the corner using a miter box or a file.

In order not to spoil the appearance of the baguette, it is necessary to properly cut off its corners. To form a normal right angle, the plinth should be cut at an angle of 45 degrees towards each other.

Determining the slope and cutting the skirting board is done as follows:

  • The product is applied to the ceiling in order to understand the direction of the cut for proper installation.
  • You need to cut baguettes in a mirror image.
  • To decorate the inner corner, the top edge is made shorter than the bottom edge.
  • Correct outer corner occurs when the top edge is longer than the bottom.
  • On the ceiling plinth, which will be located on the right side, make a cut on the left side.
  • The product located on the left side should have a cut on the right side.
  • When cutting the skirting board, you must carefully advance the knife in one direction. In this case, the formation of chips and roughness can be avoided.

The appearance of the ceiling depends on the correct solution to the question of how to glue and cut ceiling plinths.

To make a miter box yourself, you must perform the following steps:

  • Take any solid foundation and draw a line on it.
  • Then they retreat about 10 cm and draw a line parallel to it.
  • Draw a line through the parallels at right angles to them.
  • Measure 5 cm from this line on each mowing line and connect opposite points.
  • The resulting mowing lines form an angle of 45 degrees with the parallels.

To cut the skirting board using a homemade miter box, the product is laid along the parallels and cut along the marks, taking into account the direction of the corner.

However, it should be understood that for angles other than 90 degrees, it is necessary to cut the skirting board at a different slope. In this case, the product is applied to the wall and its boundaries are outlined. Then the place of intersection of the skirting boards is determined and the corresponding marks are put. The baguette cut is performed according to these marks.

Selection of material and calculation of the number of skirting boards

Ceiling plinths are very popular, for the manufacture of which polystyrene, polyurethane and expanded polystyrene were used. The main advantages of such products are lightness, resistance to moisture and temperature extremes. Thanks to the various widths and a large selection of patterns and reliefs, it becomes possible to choose a skirting board to create any decorative effect. Additional coloring of the ceiling plinths makes it possible to create a variety of artistic decor.

The problem of how to stick polystyrene and expanded polystyrene skirting boards on the ceiling should be solved with extreme caution, since they are easily deformed and damaged by mechanical stress. As for polyurethane fillets, such design elements are characterized by increased strength and the ability to maintain a clear relief shape.

Polyvinyl chloride ceiling plinth is widely used in cases where the budget for renovation and decoration of the premises is limited. However, when using it, it should be remembered that such products are not recommended to be painted. In addition, PVC skirting boards are afraid of temperature extremes, under their influence, product deformation may occur.

When choosing plaster, wood or aluminum skirting boards for ceiling decoration, you should remember a few very important points. First, such products cannot be bent due to the low ductility of the base material. Secondly, the skirting boards are quite heavy. The presence of these qualities makes the solution to the question of how to glue fillets on the ceiling, special.

Installing Aluminium Ceiling Battons in a club

Before you go shopping for skirting boards, you need to make a few calculations. In particular, it is required to determine how much material is required to decorate the ceiling in a room of a certain area. First, you should measure the perimeter of the room, this value will correspond to the total length of the ceiling plinth. To calculate the number of fillets, it is necessary to divide the perimeter of the room by the standard length of the products, which corresponds to 1.2 meters, 1.4 meters and 2 meters. Experienced craftsmen performing finishing work recommend purchasing skirting boards of greater length, in this case, fewer connections are obtained.

The width of the plinth is determined according to the height of the ceilings in the room. In rooms with low ceilings, it is better to use narrow products; for high rooms, it is recommended to install a wide ceiling plinth. This visually reduces the height of the room.

Gluing the ceiling plinth

  • Take a baguette and put glue on its back.
  • The place of fixation of the product can be moistened with a primer or plain water to increase the adhesion of surfaces.
  • The plinth is firmly pressed against the wall and ceiling and held for a while.
  • Excess glue or putty is removed immediately.
  • The resulting cracks and gaps are covered with putty.

If necessary, the skirting boards are painted in the desired color.

Using factory corners. an alternative to cutting and sawing

PVC ceiling molding corners

The disadvantage of corner pieces is that they are actually and visually larger than the baseboard, which will make the corner noticeable. This can ruin the look of the room. It is also inconvenient to use corners where the walls do not join strictly at an angle of ninety degrees. But most of the time they look great.

How to cut skirting boards to the ceiling: corners

Today it is impossible to imagine the interior of a residential building or apartment without ceiling plinths. The skirting board covers the irregularities of the suspended ceiling or wallpaper, cracks and imperfections in the walls, and gives the interior completeness. But how to make the skirting board perfectly fit in the most important place. in the corner? There are several ways.

How to make a miter box yourself?

If desired, the miter box can be made at home. It can be crafted from wood or iron. The dimensions of the workpiece do not play a special role, but the wider it is, the more accurate your cuts will be. However, if the width is greater than the length of the hacksaw, with which you will cut the baseboards or boards, then it will be extremely inconvenient to saw, so you do not need to take a workpiece that is too wide.

First, a transverse line is marked in the center of the workpiece. Then, marks are made at a distance of 1/2 the width of the workpiece from the intersection of the straight line with the edges of the workpiece. Then these marks are connected crosswise, as shown in the figure.

Wooden miter box, fastened with self-tapping screws

Next, the process of marking the side walls of the miter box begins. Attach them to the already marked base and make marks based on the base markings. Then draw straight lines from these marks across the entire wall.

The scheme of making a wooden miter box

After that, the process of mounting the miter box begins. The walls must be attached to the base with self-tapping screws if the fixture is made of wood or chipboard or corners with bolts if it is made of steel. Only after installation in the miter box are sawed slots for the saw.

After making the slots, the miter box is ready. If you have a large amount of work or want to repair regularly (on a professional basis), this simple device can speed up the process of cutting skirting boards by 5-10 times.

What tools can be used?

The feasibility of using certain tools is associated with the materials from which the skirting board will be made.

Tab. 1. Varieties of materials and features of their use.

Type of material Material properties, requirements Tool
Polyvinyl chloride (PVC) PVC skirting boards are distinguished by the fact that they are easily damaged when pressed and no longer restore their former appearance, since they are devoid of elasticity. Therefore, such skirting boards cannot be pressed when cutting. Cut with a construction knife or a hacksaw for metal. A blade or a sharpened kitchen knife will also work.
Styrofoam Foam plinth is also not very durable, but better than PVC counterparts. Easily crumbles. The same tools can be used as for PVC
Wood Stronger and more aesthetically pleasing than their polymer counterparts, but expensive. It is best to cut the tree with a hacksaw, you can use metal, although this way you run the risk of hammering the teeth of the blade with wood sawdust. A hacksaw with fine teeth is best.

Using a miter box

Factory made miter box

The miter box has a recess for a cut-off board or plinth and saw slots at an angle of 45 and 90 degrees. You will need to cut the skirting board at a 45 degree angle.

To cut the skirting board with this device, you need to follow these steps.

  • We apply the plinth to the future attachment point.
  • We mark where we will cut.
  • We put the plinth in the gutter of the miter box so that the lower part is pressed against the surface of the device, and the part that will be greased with glue “looks” up.
  • Cut off the area by inserting the saw into one of the 45-degree holes.
  • We correct the cuts with a knife or the same saw (remove irregularities).

How to cut the corners of a ceiling plinth with a miter box

After that, the skirting board can be glued in place.

How to cut a skirting board without a miter box?

The easiest way is to draw the future cut line on paper (cardboard, wallpaper), and then, attaching the baseboard blank to it, cut.

To do this, you first need to attach the skirting board blank to the paper and draw two parallel mowing lines, which will indicate the sides of the skirting board. Then, using a protractor, you will have to measure 45 degrees and draw the line of the future cut. Then the drawing is used in the same way as the miter box: a blank is placed on it and the excess is sawn off along the mowing line.

How to cut the corners of a skirting board without a miter box

The disadvantage of this method is that the saw will have to be held on weight, focusing on the drawing, and not inserted into a previously prepared slot.

Outside corners

It happens that the room has not only internal, but also external corners, which also need to be pasted over with a plinth (see photo). How to do it? There are several ways here as well. The easiest way, as with the inner corners, is to cut them with a miter box. The outer joints must be cut so that the side that will be glued to the ceiling is on the surface of the miter box, and the side pressed against the wall is facing the wall of the fixture.

As with the inside corners, you can also use in-place markings, that is, draw the line on the ceiling. Here, the technology is exactly the same as that used for the inner corners.

You can use the markings on the wall by attaching a workpiece and drawing a fishing line along its lower edge (see photo).

If the outer corner turns out to be too rounded, you can finish the joint with a knife.

Trimming the ceiling plinth. Outside and inside corners

To the point where they converge, the line is drawn directly along the future part of the connection. From the point on the ceiling to the second one. The resulting marking will be the line along which you need to saw off or cut off the connecting parts. Using these techniques, you no longer need to wonder how to cut the corners of the ceiling plinth.

If the angle is not right

Unfortunately, in some cases the angle between the walls in the room is not straight, but sharp, or, conversely, obtuse. This is due to structural defects that have arisen through the fault of non-professional builders, the architect’s idea or the result of soil subsidence some time after the construction of the building. This is especially common in village houses and summer cottages.

House plan with sharp and outer corners

No miter box or a drawing replacing it will help in this case, and you will have to do the markup in place.

  • Attach the workpiece to one of the walls so that it rests against the other wall with its end.
  • Run the line on the ceiling along the workpiece.
  • Perform the same operation against another wall.
  • At the intersection of the two lines, put a mark on the workpiece itself.
  • Draw the line from the mark to the corner of the workpiece and cut along it.
  • Do the same with the workpiece, which you will attach to another wall.
  • Glue both blanks; they will come together tightly.

We cut the corners of the ceiling plinth without a miter box

How to properly cut a ceiling plinth without a miter box? To work, you will need a well-sharpened pencil, a small piece of plinth, a stationery knife (for polystyrene or polyurethane) or a metal saw (for other materials), a ruler.

You need to attach the plinth to the corner and draw the line with a pencil along the outer edge, then attach to the other side of the corner and also mark. As a result, a cross will turn out on the ceiling, the center of which will mark the place where the plinths of the ceiling plinth should converge. Place a piece of skirting board where you will glue it. Resting the end against the wall, transfer the desired mark to it. This way you can cut the corners of the skirting board without a miter box.

Using fillets

You do not have to make fillets yourself, but immediately purchase those that were initially prepared for docking. This is how they produce expanded polystyrene fillets, which do not need to be adjusted to each other.

The baguette that will be fixed to the left must have a right cut, and the right baguette must have a left cut. When creating the inner corner, make the bottom section rise above the top, for the outer corner everything should be the other way around.

Attach the baguettes to each other, if necessary, make undercuts at the joints of the base. If everything is in order, the skirting boards can be fixed with glue or screwed to the walls with further sealing of the seams.

Making corners using a miter box

If the walls and corners of the room are even, you can use a miter box for work. In order to cut the corner correctly, the part in which the person will make a gash should be laid inside the miter box, then insert the saw into the guides. This holds the part in place and can be cut at the desired angle. For high-quality cutting of the plinth, it must simultaneously adhere to both surfaces, so it should be pressed against the wall of the miter box. The ceiling plinth is pressed with the side that is closer to you.

With a miter box, you will need to cut a 45-degree angle. First you need to decide how to position the plinth in the miter box. To avoid confusion and cut correctly, place the right plank on the right and the left plank on the left.

Follow the instructions below:

  • Press the part of the miter box that will be on the ceiling to the bottom of the miter box. The other side will be lifted up and closer to you. It can be resting on the wall of the tool, and then it will not stagger when cutting.
  • Determine the direction of the cut as shown in this figure, and then cut the corner.
  • Fold the cut pieces together. you have an inside or outside corner.

Place it on the ceiling and check the geometry. If it is not even enough, it can be slightly corrected with a knife, and in the case of minor defects and wide gaps, you can use a putty.

How to make an even corner: ways

The most difficult thing is to cut the corner so as to get a perfectly even one: the surface of the materials used is not easy to cut, in addition, you need to observe good joining, preferably without huge gaps. How to make a corner on a skirting board? You can use several methods: with a miter box, without a miter box, using decorative corners, as well as an alternative way.

How to cut skirting boards using decorative corners

With the help of them, you can easily and quickly obtain the desired angles in polystyrene or polyurethane skirting boards. Install them on the ceiling, and then glue the strips to them tightly. Cutting them is easy using a clerical knife.

What tools will be needed?

For ceiling plinths, the following tools may come in handy, depending on the chosen method of work:

  • Saw on wood. Suitable for working with wooden ceiling plinths.
  • Metal sheet. Suitable for other types of skirting boards (foam, plastic, etc.).
  • Miter box. The tool is a chute, which has the shape of an inverted P, where mowing lines are outlined at angles of 45 ° and 90 ° for cutting.
  • Electric miter saw. Can be used instead of a miter box, helps to achieve high cutting accuracy.
  • Electric jigsaw. Easy to operate, with the help of it you can efficiently and correctly cut a corner without burrs.
  • Stationery or construction knife. Suitable for foam skirting boards, it is important that it has an excellent cutting blade, and therefore must be well sharpened.

How to cut a ceiling plinth in the corners: instructions and recommendations

A high-quality renovation presupposes an attentive and accurate attitude to details. Finishing the work with the ceiling, you need to arrange it well. for this, ceiling plinths are used. As a rule, the installation of the planks does not cause any particular difficulties; you will have to tinker with the corners. Let’s take a closer look at how to cut the ceiling plinth in the corners, talk about different methods, and give useful recommendations.

Ceiling plinths from any material can be cut using one of the methods described below. They are suitable for everyone except for plastic ones: they are made out using ready-made corners.

Features of cutting ceiling plinths in a miter box

It is necessary to work with this device extremely carefully so as not to blunt the tool and not leave cuts in unnecessary places. In the process, we adhere to the following instructions:

    We fix the baguette in the miter box in the same way as it is planned to place it on the wall. The side that will be pressed against the ceiling on the miter box must lie against the sidewall.

We insert a cutting tool (hacksaw or knife) into the desired gap and cut the fillet.

  • We process the joint of the ceiling plinth and apply it to the wall to check the correctness. The foam molding can be tweaked with a sharp knife if the roughness of the end is about 2 mm. Wooden skirting boards can be simply sanded with sandpaper. For ease of use, it can be glued to a wooden block.
  • Rules for cutting ceiling plinths by marking

    This method is used to cut skirting boards in cases where there is neither a miter box nor parts from which it can be made.

    To do this, you need to make markings on the wall in this order:

      We put the baguette in the corner to the place of fastening.

    Along its one edge, we draw a base line on the ceiling for the level of attachment.

    We apply the fillet in the same way to the perpendicularly drawn mowing line on the ceiling and again draw a straight line along one side. We should have two segments that intersect at one point.

    We again apply two plinths in turn and mark this point on them.

    We repeat the same procedure now on the wall to mark the place of cutting from below on the products.

    We connect two points with a line. It can run at an angle of 38-45 degrees, since walls and corners in living rooms are often uneven.

  • Cut off the baguette along the mowing line.
  • How to cut a ceiling plinth

    articles:

    • Selection of tools
    • Cutting technology
    • In the miter box
    • By pattern
    • By markup
    • Without miter box
    • Useful Tips

    One of the most difficult steps in installing skirting boards is cutting them correctly. Only by correctly joining the individual elements at the outer and inner corners will you get the desired result. Fillets will look aesthetically pleasing and neat if you cut them off at the right angle and seal the cracks. A special tool (miter box) is used to accomplish this task. And if it is not there, then other devices will help.

    Method for cutting a ceiling plinth without a miter box

    To neatly dock fillets in the inner corners, you can do without a miter box.

    We carry out the work in the following order:

      We apply the end part of the baguette to the sheet of paper and outline the contour of the convex side. It is more convenient to use a small piece of plinth (if any).

    Cut out the resulting template.

    We transfer the contour to the surface of the baguette with a simple pencil.

    Cut along the drawn curve.

    For fitting, we put one plinth tightly with the end part to the wall, and then the second.

  • If there are small gaps, then they can be processed with a clerical knife or subsequently sealed with a sealant.
  • Cutting technology for ceiling plinths

    For a prompt and high-quality work, you need to choose a tool in accordance with the material of the baseboard and choose a cutting method. If you have a miter box, then there will be no particular difficulties in the process. If it is not there, then two options are possible: cut according to the template and measurements on the ceiling or make this tool yourself.

    Selection of tools for cutting ceiling skirting boards

    To properly and accurately cut the skirting board, you need to use a suitable cutting tool. It is chosen depending on the material from which the fillets are made:

      Styrofoam. It is characterized by low strength and is relatively inexpensive, and therefore foam models are becoming more and more popular. Their strength does not particularly affect the performance, since usually the ceiling plinth is not subjected to mechanical stress. An ordinary stationery knife is suitable for cutting.

    Extruded polystyrene foam. A cheap material with a density several times higher than that of foam. Because of this, cutting it is a little more difficult, and therefore a sharp and thin knife is used for this purpose.

  • Wood. Such skirting boards are more difficult to process, although they have many advantages (environmental friendliness, durability). They are more expensive,
    especially if made of hardwood. Before cutting wood ceiling plinths, stock up on a hacksaw.
  • In addition to the tool for direct cutting of the baguette, you will need a miter box. This is a special device made of wood, plastic or metal in the form of a box with notches on the sides. A hacksaw or knife can be inserted into it at the desired angle. Thus, the cutting angle is as accurate as possible.

      We knock three planks of 5015 cm with a long edge into the shape of a three-sided, rectangular box. Please note that an angle of 90 degrees must be observed between the side rails and the transverse plank.

    Using a protractor, mark an angle of 45 degrees on the bars. Instead of a protractor, you can use a school square. In it, one angle is 90 degrees, and the other two are 45.

  • Before cutting corners, mark the vertical direction with a simple pencil.
  • Technique for cutting ceiling skirting boards

    This method can be used if your corners are even and you want to trim the baguette exactly 45 degrees. To do this, before cutting the ceiling plinth in the corners, you need to draw a miter box on thick paper. Draw two parallel mowing lines and mark the angles at the desired degrees using a protractor.

    We place the fillet in this case in the same way as on a traditional miter box. Please note that you need to cut the skirting board holding the tool in a strictly vertical position.

    Tips for cutting ceiling plinths

    When working with a miter box, there are two points to consider:

      The inner corner of the ceiling plinth is formed from two elements: the first one we put on the right in the miter box and cut from right to left, the second we start from the left and cut from left to right.

  • We start the first part of the outer corner from the left and cut from right to left, the second we start from the right and cut from left to right.
  • In addition, you need to know the following nuances before cutting the skirting board:

      Before you start cutting a baguette with a miter box, try cutting a test strip to avoid mistakes.

    You can make the correct measurements by measuring the length of the inner corners of the plank on the inner side, and the outer ones from the point of the inner corner to the width of the fillet deep into the room.

    If the baguette is installed under a stretch ceiling, then it should be attached only to the wall. The adhesive composition should never get onto the vinyl sheet.

    The final fixing of the skirting board should be carried out only after the exact fitting of the plank.

    If the corners and walls in the room are even, then the fitting can be done on the floor.

    When installing baguettes, it may be necessary to adjust them several times, therefore, stock up on tools and patience.

    Instead of a template and a miter box, you can cut in the corner between the wall and the floor, or by moving the table against the wall. In this case, on the wall, ceiling and baguette, you need to mark the cutting angle of the end.

    If you are interested in the question of how to cut a ceiling plinth without a miter box, and you do not have time to use templates, then you can purchase special corner inserts in advance. They will hide gaps, but will protrude and stand out on the coating.

    If you have a skirting board made of precious wood, then you need to cut and install it very carefully, since a large amount of putty for sealing joints will be too noticeable, and painting over a baguette is an inappropriate solution, because this way you will hide the natural texture of the solid wood.

    Polystyrene foam products do not have to fit close to each other due to the soft texture, but wooden and plastic models should be well docked.

  • If the trapezoidal niches on the wall need to be bypassed from above with a plinth, then we join the piers at an angle different from the straight.
    In this case, cut the plinth at an angle equal to half the joint. For example, if the walls are joined at an angle of 120 degrees, then we cut the fillet at an angle of 60 degrees.
  • How to cut a ceiling plinth. look at

    Method two. no additional tools

    For the inner corner, you can use the simplest way of perfect joining. by marking on the ceiling. Another example of how to cut a corner nice and even.

    • Apply a fillet to the ceiling, firmly pressing its even edge into a corner.
    • Draw a line along the long side of the plinth on the ceiling.

    • The same action is done with the adjacent part on the other side.

    • Mark the point of intersection of lines.

    The end result is an even 45 ° angle when you draw the line from the point of intersection to the edge of the part. Note that the above marking method works only at perfectly flat corners.

    The first way is with a miter box

    Professional miter box with rotary hacksaw

    The miter box usually looks like a tray with vertical holes for a hacksaw. It can be made of wood, metal or plastic. This tool represents the oldest and simplest carpenter’s tool for cutting wood pieces at 90 ° and 45 ° angles. There are types of such a device for professional work, with a rotary mechanism, in which the cutting tool can be rotated and fixed in any position.

    How to cut a ceiling plinth correctly

    Ceiling corners are divided into internal and external, the method of joining on them is slightly different.

    If necessary, you can make a miter box with your own hands. To do this, you will need three trims from plywood or boards of the same size. First, they are applied in the form of an inverted letter “P” and the corners are marked. Then, according to the marking, slots are cut out for a hacksaw almost to the very bottom, and the boards are twisted.

    How to cut the corner of a skirting board evenly

    A beautiful and neat edging of the ceiling hides the joints between the coatings and is an additional element of the room’s decor. But in order for the ceiling plinth to look really beautiful, you need to be able to qualitatively join its corner joints.
    How to cut the corners of the ceiling plinth evenly can be found in our article.
    Related article: how to properly glue the ceiling plinth with glue and putty.

    Inner corner

    • Making the right measurements.
    • We install the plinth strip in the miter box so that this position exactly coincides with the placement on the ceiling.
    • The plinth should be firmly pressed against the opposite wall of the miter box. Hold and press with your free hand.
    • We put a hacksaw at an angle of 45 ° in a special hole and cut off the part.
    • The adjacent part must be cut in the same way, only in a mirror image, as shown in the photo.

    When cutting soft materials (PVC, expanded polystyrene), use a hacksaw for metal or an ordinary construction knife. Then the work will be neat and with smooth edges.

    Outside corner

    • Measure the length of the plinth from the nearest wall to the outer corner, leave the fishing line on the wrong side with a pencil, indicating the desired length. It should be noted that the edge (its upper part) should protrude slightly outward.
    • The plinth is moved to the miter box and cut off.
    • The adjacent bar also needs to be measured with a margin and cut off in a mirror image to the first part.

    Trying on the ceiling plinth: the joining of the parts should be perfectly flat. If the result is not achieved and there are irregularities at the joints, you can trim the edges with an ordinary knife until a perfect fit.

    Checking the smooth docking

    All the nuances are well described in the video:

    other methods

    With a good eye and accuracy of hand action, you can use a homemade template that resembles an imitation of a miter box. To do this, take a thin board or thick plywood and draw a layout in the form of a horizontal rectangle. Using a protractor, mark 45 ° on the right and left sides of the rectangle. Draw mowing lines connecting opposite edges. You can now cut off the ceiling plinth using this layout. The actions are simple and similar to the description above in the first option. Only the ceiling parts should not be inserted, but placed on the drawing and the hacksaw should be combined with the layout of the layout.

    How To Install Skirting Boards. DIY At Bunnings

    Special accessories for docking

    Skirting board for a stretch ceiling: basic rules for selection and installation

    Stretch ceilings are no longer a wonder. Beautiful, durable, they give the ceiling a perfect look, repel dust, are not afraid of water. A stretch ceiling is not only able to close irregularities, it also successfully hides external wiring or plastic pipes. The ceiling is mounted very quickly and completely without dirt, accompanying other repair and construction work. It is only necessary to mask the gap between the canvas and the wall. How to do this can be seen in the photo, many of which are on the Internet. To do this, use a masking tape or plinth for a stretch ceiling.

    A successful choice of skirting boards for the ceiling will give the interior a complete look

    How to choose a skirting board for a stretch ceiling

    Ceiling plinths for stretch ceilings are mainly made of polystyrene (expanded polystyrene) and polyurethane. Polyfoam is a very light material. It adheres well, is easy to cut and is affordable. Its disadvantage is fragility and fragility; it is not suitable for complex ceilings. Styrofoam burns, emitting toxic substances, it is better not to use it in the children’s room and bedroom. Not all glue is suitable for foam plastic; some aggressive media can spoil it. Styrofoam skirting board may turn yellow over time, it is recommended to paint it before fixing.

    Wooden skirting board gives the interior a chic look

    The ceiling plinth for a stretch ceiling made of polyurethane is more flexible, it can take on various forms (see photo). Polyurethane is glue-resistant, washable, ideal for bathrooms and kitchens. But polyurethane sometimes sags under its own weight. Therefore, it is necessary to mount the polyurethane skirting board very carefully, and if it is very wide, it is more advisable to fix it with self-tapping screws, and fill in the attachment points.

    LED strip for lighting ceilings. Basic accommodation options. The rules and subtleties of choosing such backlighting options. Placing LED strip on the ceiling, installing it.

    Wooden ceiling plinth is rarely used due to the high cost of the material and the complexity of installation. In addition, it will not be possible to mask errors in the joints on a wooden baseboard. A plastic skirting board for a stretch ceiling is also not very suitable, because having a small width and a rigid structure, it will not be able to mask the flaws of the walls.

    Plastic skirting board with imitation of artistic modeling

    Helpful advice! For a classic interior, a wide ceiling plinth with an imitation of stucco molding is suitable, and for a modern youth room. narrow, strict fillets for stretch ceilings. Photos of such skirting boards can be found on specialized sites. When choosing a pattern, do not forget that the more complex the pattern, the more difficult it will be to adjust the corners.

    Glue and paint

    When choosing an adhesive, take into account the characteristics of the baseboard material. So, polymer-based glue may contain a solvent that can damage a foam baseboard. And for polyurethane, it is perfect due to its reliable adhesion and short setting time. Before gluing the ceiling plinth to the stretch ceiling, it is better to check the material compatibility on a small piece.

    The so-called liquid nails have proven themselves well. They are safe for any kind of skirting board materials and have a very high adhesive power. You need to choose liquid nails based on the functionality of the room itself. Acrylic is safer and does not have a strong odor, but they are not used in rooms with high humidity. For the bathroom and kitchen, formulations based on an organic solvent (neopropylene) are suitable. When performing such work as gluing skirting boards on stretch ceilings, you must follow safety rules.

    Before installing the ceiling plinth, markings are made, along which its lower edge will be glued

    Helpful advice! Professionals often use acrylic based putty. This mixture sets very quickly and is absolutely safe for humans. In addition, it can cover all the joints of the corners, as well as the gaps between the baseboard and the wall.

    Material calculation and tools

    To calculate the required amount of material, you need to calculate the perimeter of the room. This applies, first of all, to rooms with complex geometry. The resulting figure should be divided by the length of the strap of the selected model, and as a result, we get the required amount.

    It is recommended to purchase an additional bar in order to avoid the need for additional purchases if unforeseen difficulties arise during the work.

    Trimming the corners of adjacent fillets

    Of the tools you will need:

    • construction knife, hacksaw, sandpaper;
    • miter box. This is a special tool, as in the photo, that allows you to easily and neatly file corners. It is important to check the direction of the cut;
    • ruler, tape measure, protractor (if the corners are not perfectly even);
    • simple pencil for marking;
    • rubber and metal spatulas.

    Miter box for trimming skirting boards

    Skirting board for stretch ceiling

    One of the significant disadvantages of the masking tape is its small width. The distance between the walls and the stretch ceiling can be uneven, in some places becoming so wide that the masking tape cannot cover it. In this case, it is better to choose a ceiling plinth.

    You can hide the curtain rod behind the wide skirting board

    Ceiling skirting boards serve more than just a camouflage function. Stretch ceilings without a plinth do not look so impressive. As shown in the video and photo examples of interior sites, a skirting board for a stretch ceiling can give a room a finished look, make a design more interesting, emphasize the overall style, advantageously shading a stretch ceiling. Which skirting board to choose depends only on your imagination. Photos indicate that the skirting board for stretch ceilings can be painted in any color, it can imitate stucco or even wood. It is quite easy to choose a ceiling plinth according to your taste and wallet, you just need to figure out what exactly is right for you.

    Helpful advice! Before starting work on your own, study the materials, read articles and watch a video on how to glue skirting boards on a stretch ceiling.

    Installation of masking tape is very easy

    Stretch ceiling masking tape

    A masking tape, or a plug for stretch ceilings, is often supplied by the manufacturer in a set, like other accessories for stretch ceilings. You need to fix it directly into the groove of the profile. It prevents the formation of dust and dirt that would inevitably accumulate in an open crevice.

    Helpful advice! The advantage of a masking tape for a stretch ceiling is the possibility of its repeated use. If it becomes necessary to dismantle the ceiling (flooding, repairing wiring, etc.), the tape can be easily removed and just as easily reattached.

    The masking tape can be matched to the color of the stretch ceiling surface

    Masking tape is used to decorate multi-level ceilings, as evidenced by photos of such examples, as well as when splicing canvases. It is advisable to use a decorative insert for stretch ceilings on flat areas, otherwise it will only emphasize all the irregularities.

    How to glue a skirting board to a stretch ceiling

    The canvas of the stretch ceiling is subject to natural deformation depending on temperature changes. In addition, sometimes it becomes necessary to dismantle the ceiling. That is why the skirting board for the stretch ceiling needs to be fixed only to the walls. You will learn more nuances from the video on how to glue a plinth to a stretch ceiling.

    When deciding which plinth is better for stretch ceilings, it is important to know that special requirements are imposed on the plinth for a stretch ceiling:

    • it should have the most lightweight design;
    • the plinth must ensure a snug fit to the wall;
    • for its installation use special glue or putty.

    Foam plinth construction

    If you choose a wide molding instead of a plinth, this will minimize the problem of how to fix the plinth to a stretch ceiling. Moldings are originally designed to be fixed to walls.

    Helpful advice! In the molding, offset 10 cm from the ceiling, you can place hidden lighting. This will add impact to your interior. It is better not to place the power supply under the ceiling, as it heats up quite a lot and has a decent weight.

    LED strip as a backlight can be hidden in a wide molding