How to get a gas toss without a starter. When pressing gas

How to get a motorcycle without a starter

After starting, do not rush to immediately run the trimmer. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a trimmer line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 3040 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

By cooling the benzokos, we continue to run the engine according to the previous scheme. Start

For hot, trimmer is already needed with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the running.In the gearbox of a gasoline braid. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, the roller.Described gas troops according to the described algorithm are carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.Term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

A gasoline trimmer is a surprisingly desired tool with which you can dig not only a small clearing in front of the house, but also a whole large lawn of large sizes. Often, there is nothing endless here, if you can then encounter that the trimmers do not start up.

It often happens that users of such cars try to “save”, pouring into the tank not a fuel with an ordinary octane number, but something incomprehensible, which has been in a plastic canister for almost ten years.

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. But you certainly remember how to correctly store fuel.

What to do when the fuel was definitely ordinary, the spark of course, however, the trimmer is not started by a gasoline trimmer? You that you just flooded the candle with gasoline. And then it needs to be unscrewed, wiped with an unspoken rag and dry. When, it will be completely useful to check the spent on the performance.

How to start a three.Dimensional motor or bush?

The new trimmer is simple during commissioning.

• Check the type of engine engine. Trimmers are equipped with a 2- or 4-stroke engine.
• Buy oil for this type of engine. The trimmer is gasoline. AI-92/93/98, sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1,34 with gasoline, synthetic. At 1: 50. Follow the recommendations of the trimmer manufacturer for the viscosity of the oil (see. Label on the flask). The most commonly used 5W-30 Polyhedral oil. Do not use motor oils without control.
• Pour a small amount (for example, 0.5 liters) of fuel obtained in the tank.
• Close the air damper, moving the desired lever (see. Manual).
• Turn the ignition key (or handle) to the on position. Without this, the trimmer will not start. Beginners often make this mistake.
• Download a little fuel to the carburetor. If there is a manual rocking with a separate button or lever (see. Instructions). 4-7 clicks are required.
• Place the trimmer on a flat surface.
• Gently pull the starter cord until you feel its braking. Then pull it sharply, but not completely. Repeat this movement up to 4 times.
• If the engine does not start, open the air damper again, otherwise the spark plugs will be seasoned with gasoline with further movements of the cord. Make 2-3 attempts to run an open parking brake.
• If the engine still does not start, close the shutter and make a few more attempts to run it.
• When the engine is launched, press the throttle lever to activate the idle mode.

Why is a gas cocker?

The reasons why the trimmer does not start can be a lot.

Most often, the reasons for the difficult launch are:

• Fuel quality problems;
• Candy malfunction;
• Pollution of air and fuel filters;
• Problems with leveling pressure in the gas tank;
• Falf in the graduation channel.

Most often these malfunctions are not critical and they can be eliminated independently. Let’s consider in more detail how to do it.

Fuel

Do not save on combustible for your technique, use only high.Quality gasoline and oil. Strictly adhere to the recommended proportions for the fuel mixture. Also, you should not leave fuel in the tank for a long time. It over time is flooded and loses its properties.

Candles and candle channel

If you suspect a malfunction of the spark plugs, you should immediately unscrew the old candle and replace it with a new. If there is no possibility to instantly install a new candle. Thoroughly clean and dry the old. Drain excess fuel through the candle channel and dry it thoroughly. After that, plunge the candle into place, set the gap of 1 mm and try to start the braid again.

If the proposed manipulations did not give the desired result. Check the contact of the candle. Also, the reason for the lack of a spark may be a faulty ignition unit, which is unlikely to repair it independently.

Air and fuel filter

Pollution of these nodes of the gas troops is fraught with either their complete replacement, or thorough cleaning. When replacing the fuel filter, do not leave a suction pipe without protection. This can provoke a breakdown in the piston system of the engine.

Problems with leveling pressure in the gas tank

This malfunction is associated with the contamination of the soundtress. When this part is salted, a vacuum forms in the gas tank, which prevents fuel supply. You can clean the soundtress using a conventional needle.

If, after checking the data of the trimmer systems, he did not start, most likely, the reason for problems with the carburetor (clogged nozzles, disturbed tightness) or engine (wear of piston rings, chips on the cylinder). Repair of this type can also be carried out independently, but it is better to trust the specialists of the service center.

The process of commissioning benzokos, no matter you bought it now or got it after winter storage, the rules listed below will allow you to avoid the main errors that may damage the tool.

Suppose you just bought a gasoline trimmer. Remove the instructions out of the box and see if all parts of the benzos that are indicated, you have. After that, you can start in the assembly.

Preparation of the fuel mixture and refueling

For the convenience of preparing the fuel mixture, it is better to have, where one part contains gasoline, and in the other 2 stroke oil. We recommend getting it like that, it is very convenient to use

Next, take a measured container, with a scale applied to it, with its help you can prepare the mixture as accurately and quickly as possible. Look in the instructions which brand of gasoline and 2-stroke oil are recommended by the manufacturer of your model benzokos. Pour gasoline and oil into a container for the preparation of the fuel mixture, according to the proportions specified in the instructions. Then the finished mixture neatly, through the funnel, pour into the fuel tank of the trimmer. The ratio of gasoline and oil should be just the same as indicated in the instructions. This is a very important point!

Launch of gas.Crocks with an unheated engine

For the first launch of the benzokos, find the air damper lever and put it in position “Closed”. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

If the engine started after 5 jerks, then open the air damper. If this does not happen, still open the air damper (with an open damper and continuation of attempts to start the engine, the fuel flows a candle and you will have to dry it, and this is extra waste).

If the engine does not start, with an open damper, then close it to continue to pull the cord. The first launch may be quite difficult and demand up to 15 jerks. After the engine has begun to work, click once on the gas lever, so you will use idle. Now let the engine work and warm up. After that, it can be stopped by pressing the “Stop” button.

Launch of a heated engine

It is very simple. Put the switch to the working position and pull the cord to the start. If you do everything according to the instructions, then problems with the launch of good gas troops should not arise.

Basic errors when starting

We list the main errors that beginners make when starting a gasoline trimmer:

• Starting the engine when the ignition is turned off;
• Starting with a closed shutter with the number of jerks more than 5 times;
• Incorrect fuel mixture.

By acquiring a brand new lawnical mower, we all show increased singing and respect for the instrument: we admire it and boast, carefully read the instructions, wipe the rag, do not load hard. But time passes, and the beauty of novelty disappears. The lawn mower becomes just a good working tool. Here and it is important not to cross the line so as not to do what the people call with your favorite lawn mower. To “ditch”.

A method of starting a hot engine and an engine equipped with a decompression system.

Hot engine, does not need to enrich the mixture of fuel with air, so you can start the saw without closing the air damper. The ignition is simply turned on and the starter is moved, after which the working chainsaw should be launched.

Large.Volume engine, have a fairly serious compression, which extremely complicates the process of turning. To reduce the efforts required to start a large volume and power saw, manufacturers use special decompression valves, when pressed on which the compression is noticeably reduced and the engine is easier.

Valves can have different views, so study the instructions for the tool in advance.

Thus, before any type of launch, whether hot or cold, it is necessary to press this valve designed to reduce the resistance, and thereby increase the service life of the starting device.

In the conclusion of the article, you can summarize the key points of launching the chainsaw. First, you need to start with maximum safety. Second, any deviations from the launch algorithm are not allowed. And finally, do not start a chainsaw without a starter! Consider the information from the article and use your tool correctly.

What fuel to use for chainsaw?

The choice of suitable fuel is an important and significant issue. The only correct approach to its solution is a careful study of the user’s instructions, which indicates the type and brand of fuel, the proportions of mixing gasoline and oil, and also reflects all the features of this tool. Modern standards require the use of high.Octane purified fuel and special types of motor oil.

Choosing gasoline

Many are interested in what gasoline the chainsaw works best. Most models require pure high.Quality fuel with an octane number not higher than 90. Sometimes on the network there are recommendations to mix 92 or 93 gasoline with 95 to increase its effectiveness. This should not be done in any case, since higher.Octane brands are often faked, and no one will dilute the A92 or AI92 brands.

Therefore, choosing which gasoline to pour in a chainsaw in the conditions of the domestic market, it is recommended to use just such fuel. It is necessary to ensure that gasoline is fresh enough, since with prolonged storage in it begins the release of resins and other elements that worsen the quality. Manufacturers recommend using:

• Shtil chainsaw 180. It is better to season with gasoline of the A90 brand and above;
• Shtil 250. Works on gasoline with an octane number of at least 90. You should not use fuel with ethanol, exceeding 10 %;
• Partner. It is necessary to use only unhealthy gasoline with an octane number of at least 90;
• Khuskvarna. Gasoline with an octane number of at least 90, it is allowed to use pure fuel or with the addition of tetraethylsvin. Catalyst engines require the use of fuel-oil mixture from unhealthy gasoline.

As a rule, the owners of such tools use AI92 gasoline, which is fully consistent with the requirements of manufacturers. However, for most domestic chainsaws, A72 or A80 gasoline is quite suitable. It must also be borne in mind that the failure of the chainsaw due to the use of low.Quality fuel is not a warranty case.

The choice of oil

Two types of oils are used in the chainsaw. Motor and chain (adhesive). They cannot be confused, since the tasks that they perform differ from each other. Any transmission oil can be used to lubricate the chain, although manufacturers always recommend using the same materials of the same name. Requirements for motor oil is tougher. All manufacturers are unanimous in this matter. You should use the oil of the same company that made the saw.

There is no lubrication system in two.Stroke engines, which replaces the presence of a certain amount of material in fuel. The carburetor injects the fuel-oil fog, which simultaneously lubricates all the details. After that, the remains are burned in the cylinder. If there are no specific instructions in the instructions, any two.Stroke oil can be used.

For different tool models, manufacturers recommend:

• For a chainsaw, calm 180. The best option. STIHL HP, HP Super or HP Ultra;
• Shtil 250. Properly use the STIHL HP, HP Super or HP Ultra oil, the most efficiency shows the STIHL HP Ultra oil;
• Partner. Any two.Stroke oil. It is forbidden to use automobile or ship oil, this will lead to the failure of the engine;
• Khuskvarna. The manufacturer recommends using a two.Stroke oil Husqvarna. It is forbidden to use oil for four.Stroke engines, or for two.Stroke water.Cooled engines.

The algorithm for starting a chainsaw

In order to Bind several processes should occur at the same time. This is the supply of the fuel mixture for the engine piston, its maximum compression and the supply of sparks at this moment for ignition and launch.

All these processes occur at the moment when we pull the starter handle. If you have a new chainsaw, then do not forget that it should be running in.

But not everything is as simple as it seems, fuel for launching in a cold and hot engine mode should vary in the quality of the air mixture. For example, a hot ICE can start with a normal level of air, in which it works steadily and confidently holds idle speed. The same amount of air will be too much to Bind cold engine, and before Bind The chainsaw will have to be pulled starter 10 times, and maybe more. How to solve this problem?

H1 700 starter (trying to bring back a dead starter)

To reduce the amount of air and increase the supply of fuel, manufacturers of chainsaws installed a special damper in the carburetor, which is responsible for the process of adjusting the amount of air at the time of the release of the internal combustion engine.

Start the saw engine with its help several times faster, which increases the duration of the starter and the entire saw in general.

Starting a saw in the place where it was refueling is dangerous.

Since the right to run the saw? The start algorithm is as follows:

• Fully block the air damper. To do this, in all chainsaws, a special lever is installed, pulling which is closed.
• Using a primer, pump up fuel in a carburetor. This is necessary so that the ICE does not require several working tacts to fill the carburetor.
• Make several movements by the starter, until the first fire in the cylinder. It is called the first flash. At this point, we will dwell in more detail due to its extreme importance for proper starting. It is at the time of the initial fire that the optimal conditions for subsequent launch are created. Under the influence of temperature from the first outbreak, fuel in the cylinder evaporates, forming gas pairs, and as everyone knows, it is they who participate in the work of the internal combustion engine. Therefore, the next stage should complete the process, and finally Bind The engine of the chainsaw.
• To open the air damper half and move the starter. After these actions, the chainsaw should start and start working at high speeds, to normalize them, it is necessary to click on the control lever for the number of revolutions to the maximum and immediately lower. After these actions, the correctly adjusted engine will go into idle mode and reduce the moment.

What will happen if you do not open the air damper after the first outbreak? The answer is simple, the carburetor will not reduce the supply of fuel into the cylinder, and it will flood the electrode of the candle. After that, even a large number of movements by the starter will not allow Bind a chainsaw.

The reasons for not twisting starter there may be a malfunction of a retracting relay, a weak charge of the battery, poor electrical contacts in the diagram, mechanical breakdown of the starter, and so on. It will be useful for each car owner to know what to do in the case when the starter does not twist the engine. Indeed, in most cases, the repair can be done with your own hand. Over, the breakdown usually occurs at the most unforeseen moment when there is no way to use the help of an automaker. Next, we will consider in detail the causes of the malfunction and methods for their elimination.

Closing terminals with screwdriver, mount or wrench

If a faulty traction relay, the method of direct circuit is used by any metal rod of the desired length. It can be a screwdriver, wrench or mount. A characteristic click of the key during the turning of the key in the ignition lock is evidenced of. The starter at this moment is unable to crank the crankshaft, since the teeth of Bendix do not cling to the crown of the flywheel. Having closed the power terminals of the starter, it will be possible to start the current for electric views directly. Wrench or screwdriver will take over the functions of the traction relay.

Be sure to put the car on the handbrake and in the neutral before this, in order to avoid accidents. The tool itself should have an isolated handle and a rather thick rod. Therefore, it is recommended to use one of the above items. Mount or key can be wrapped with electrical tape at the capture site.

Close contacts b and s, m and b. It is strictly prohibited! Decoding: B. Bold or thick wire. Contact of the constant voltage. On many starters, a protective rubber hat is closed and marked “12”. M. Motor or electric motor. S. Start, contact is made in the form of a threaded lifting, petal or plug, often closed with a plastic tip, so before forced closure you need to remove. 8. Minus contact, connected to the body.

On some models of the car (VAZ 2109, 2110, 2114), to drive the starter with a screwdriver, you need to dismantle the air filter and disconnect the chip laid on the contact group. After starting the motor, everything is going back.

Video: How to start a lawn mower without a starter

Pull the cord abruptly! With one hand, bend the body of the lawn mower, take the cord with the other hand and sharply pull it up. You may have to do this several times before starting the engine.

• If the engine sneezes, but does not start, check if gas is enough in the tank.
• If the engine does not sneeze and does not work, check the spark plug.

Read the instructions for the operation of the mower. If the lawn mower still does not start, read the instructions in the disruption section. You can answer your question.

A few reasons

Often users of such machines are trying to “save”, not pouring fuel with an ordinary octane number in the tank, but something obscure that was in a plastic canister for almost ten years.

Adviсe

• Always clean the lawn mower after work. Dry grass can firmly adhere to this. It also smells bad when it starts to rot. Therefore, as soon as you finish the mowing, clean the lawn mower from the grass.
• Never leave the lawn mower in winter with gasoline in the tank. He can thicken and clog the carburetor during storage.
• Never launch your mower without proper lubrication if you do not like to buy new mowers every time.

The main thing. Fuel mixture!

In this case, the remnants of plastic dissolved in harsh conditions make things in the combustion chamber so terrible that you simply cannot do without a complete sorting of the mechanism. Basy self.Propelled lawn mowers. This is a choice. But, of course, you will always remember how to store fuel correctly.

What to do when the fuel was completely normal, a spark appeared, but the gas trimmer did not start? Perhaps you have just flooded the candle with gasoline. In this case, it must be unscrewed, wiped with a clean fabric and dried. Reliable electronic trimmers. By the way, checking the candle itself for effectiveness will be completely inappropriate.

The reasons for the lawn mower may not begin

It is forbidden to run the lawn mower for the following reasons:

• First check the fuel tank before starting the engine. A small amount of this will create air in the system, but it is also impossible to fill the tank until the end. When refueling, follow the highest fuel mark. If the lawn mower is not intended for storage in winter, fuel must be drained, since gasoline tends to evaporate. Refueling is carried out using a funnel. Before spinning gasoline into parts of the lawn mower, the engine should not be launched to avoid burning water.
• Often the braid engine does not start, because the user cannot do this properly Start. Before starting, the lever sets the maximum speed, and then rolls the gas into the carburetor using a primer. The starting cord is carefully pulling, and then tightly pulls.
• After unsuccessful attempts to start the engine, you can try to replace the spark plug. Often the reason lies in this. If there is no spare candle at hand, and the old is covered with thick soot, it should be cleaned with fine.Grained sandpaper paper.
• The clogged air filter causes the formation of a poor fuel mixture, and the engine stagnates or does not start at all. To eliminate the problem, just rinse the filter removed with clean gasoline, and then dry it in the air. Rinse air filters every 25 hours, even if the braid does not linger.
• Immediately after starting, the engine can drive through a jammed piston or crankshaft. With the light spark plug removed, the starter cord must be pumped several times. It is possible that moving parts will develop, and the problem will be solved.
• Low oil level in the crankcase can lead to engine start.

Electric lawn mowers also have their own problems that are easily solved:

• A common cause why the mowing engine does not work, there may be a lack of electricity or low voltage. Find out if there is a current on the network using the screwdriver indicator, but you need a multimeter to measure voltage.
• Electric cosliner is equipped with engine heat protection. Due to the clogged ventilation holes, protection against grass will always work without starting the engine. This is easy to solve the problem by cleaning the ventilation holes.
• The cause of the mowing engine may be a faulty switch. Here you will have to contact the service center or replace the faulty part yourself.

If none of the above tips helped you launch your device, nothing else needs to be touched, but it is better to consult a specialist.

The video talks about the preparation of the lawn mower for launch:

Video: how to start a benza

After starting the engine, give the full gas and completely release the gas lever. Typically, the trigger should turn off automatically.

Features of starting from a cold and hot engine

To start the engine, several processes occur in the device at the same time. The fuel mixture begins to enter the engine piston, it is compressed and ignited by the spark plug. At the same time, the quality of the air mixture differs, starting with cold and hot internal combustion engines.

If the normal level of air is sufficient in preheated condition, it is not enough in the cold state. In this situation, you need to tighten the starter repeatedly, which leads to the wear of his cable. There is a special valve in the carburetor for regulating air mass. In cold weather, it must be completely opened, if necessary, download fuel directly to the carburetor using a primer. This will accelerate the launch of the chainsaw and reduce the risk of breakdown of its main components.

How to keep a tool?

There are several ways to make a chainsaw work. The easiest option. Place the tool on an even surface, take the upper handle with your left hand, while maintaining protection for the legs. The second method. Hold the upper handle of the saw with your hand and fix the back between the legs. This position is suitable only for low.Power and compact models of household chainsaws.

Figure 4. How to hold a chainsaw

Check the oil supply

So that the chain glides along the headset, there is a special oil tank in the engine crankcase. He supplies oil to the bus. Its work is controlled by a special pump, which starts with an increase in the engine speed. To check the feed and operation of the lubrication process, it is necessary to remove the side protection of the tire, start the tool. If the oil enters the headset and decreases in the tank (check using the buttons), no action is required. If the mixture is not enough, it is recommended to clean or replace the filter, and then adjust the flow.

Distinctive features of the factory of different brands

In some models, the launch system may vary slightly. The main difference is the location of the main elements on the case (the presence or absence of a primer, the number of bolts for tensioning the chain, etc. D.), As well as the proportions of the fuel mixture. After receiving the tool, you should carefully read the instructions that always indicate the algorithm of the first launch, stamping and the frequency of preventive measures.

Features of the winter start

Before starting work in winter, it is recommended to first bring the chainsaw to the warm room for 10-15 minutes. If this is not possible, run the tool at idle by pressing the air damper in the middle position. Increase engine power only after preliminary heating. Some models have the opportunity to switch air flow for the summer and winter. This is the best solution if you often work in the forest at any time of the year.

Is it possible to start without a starter?

It is impossible to start a chainsaw without a starter. In the absence of this element, technological disorders will occur during engine cooling, as it contains the so.Called “snail”, which regulates the supply of cold air from the flywall of the flywheel to the engine cylinder.

Starting an engine without a starter with a manual transmission

The engine on the front.Wheel drive car can be started using the front wheel:

How to start a saw without a starter

If the engine of the new chainsaw does not start, then the reason may be as follows:

• The tool is incorrectly prepared to launch.
• A poor.Quality, “old” or incorrectly prepared fuel mixture was refuel.
• The sequence of actions when starting.

When it is not possible to start the chainsaw engine that was in operation (usually after a long downtime, unskilled repair, or as a result of natural wear of parts), then, in addition to the reasons listed for a new tool, the problem may be as follows:

• Before storage in the chainsaw, the fuel mixture was left.
• Air filter is closed.
• The power system is closed.
• Incorrect carburetor adjustments.
• Non.Working or “flooded” spark plug.
• Blinds of the cylinder.Piston group.
• Air leaks.
• Pierced combustion products muffler.
• Weakened by vibrations or improper storage of fasteners.

In the listed cases, you should contact the service center.

Necessary tools

You will need very few elements that can be easily found in any construction store. Basically, the adjustment will be carried out by popular improvised tools that are easy to find in every home.

The last element is best purchased in a diameter of 14 mm. This is the most optimal size that is suitable for any model. After all the collected details, you can start the process of launching motorcycles without a starter.

Ways to eliminate breakdowns

It is not a secret that the best and more effective repair method is a prevention of probable defects. As already noted, one of the main points will be how the gasoline-oil mixture is correctly prepared. Its components should be gasoline at least AI-92 and high-quality motor oil. The proportions, taking into account the mixture, are indicated in the manual of the manufacturer, which is included in the supply of supply of at least any gasoline trimmer. Usually, gasoline oil is added using a regular honey syringe. In a similar way, it is easiest to observe proper proportions. Pretty often when the troubles with the launch of motorcycles appear, the tool holders try to carry out repairs with their own hands. In the presence of the necessary knowledge and abilities, such an approach will allow to significantly reduce operational costs. First you should check the fuel system and, namely, the filtering element. If clogging is detected, the filter will be easiest to change the new. If an air filter has become source of troubles, then you can get out of a difficult situation even in the process with insignificant temporary costs. It will be necessary to fulfill subsequent acts:

• Remove the filter element;
• Specifically in the working criteria, you can wash the filter used by gasoline;
• When operating, braids at home or in a summer cottage for cleaning use water and ordinary detergents;
• After washing, the part is painstakingly rinsed and dried;
• A hundred percent of a dry filter should be greased with engine oil;
• Excessive substances are removed by compressing the filter element with the hands;
• The purified part is put in place and strengthened the plastic cover with screws.

If the described acts did not provide a good result, then the subsequent step will be adjusting the idle stroke using the corresponding carburetor screw. This topic is devoted to many publications and videos posted in the vastness of the global network. When trying to solve the difficulties under consideration, you can take a couple of steps.

The trimmer is placed on the side so that the Airy is from above. This will allow the fuel consistency to enter the lower part of the carburetor

Often, the samples of the ICE are successful if you dismiss the mentioned part and almost a couple of drops of gasoline to send specifically to the carburetor itself. If, after all the outlined actions, the braid did not come out to bring into working condition, then attention should be paid to the state of the candle and, namely, the presence of a spark. In parallel, a hundred percent removes all fuel from the combustion chamber. Often the owners of the benzos are in situations where the fuel and air filters are unsented, the candles are serviceable, the fuel mixture is the latest and high.Quality, but the internal combustion engine does not show signs of life

In similar cases, experienced specialists are advised to use the universal and experienced long.Term practice way to start. You need to transfer the air damper to a closed position and pull the starter handle once. After the damper, the engine is opened and the launch of the motor is made 2-3 times. In the vast majority of cases, the result is a positive.

The spark plug in the process of starting the ICE of the trimmer can fill in the fuel. Even with a high.Quality consistency and the presence of a good sparks, it is unlikely that you can get a device. A more effective exit will be the extraction of a candle and its drying. In parallel, you can check this spare part for performance, when identifying defects, change it. This procedure contains a number of ordinary steps, but specifically:

• Drown out the device and wait for the aggregate cooling completely;
• Turn off the wire;
• Extract the candle itself;
• Examine the dismantled part;
• Make sure the presence of a gap (0.6 mm);
• Screw the latest, work candle and tighten it.

In practice, many repair work related to the fact that the braid did not start and which at some point have to face the use of household benzocouses, you can completely cope without the help of others. But with harsh defects, it will be most rational to contact a special service. But the main factor in similar cases will be the ratio of the repair price and the price of the new trimmer.

Fuel pouring through the openings for candles

If there is no manual swing on the trimmer engine and the device did not start, add a little fuel into the motor itself through the candle moves. Make the following.

• Check if the fuel level is sufficient in the tank for draining a small amount of it. It takes only 20 ml.
• Remove the cap from the candle and unscrew it with a candle key.
• If the candle is polluted on the former use of the trimmer, rinse and buy it. There should not be any deposits on the electrodes of the candle. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the candles for the factory defect.
• Return the candle back and check the spark look (category between electrodes) when the starter triggers.
• Remove the candle again. Using a 20- or 50-cup syringe, pour 20 ml of gasoline into a candle hole from under a candle.
• Insert and fix the candle by setting the magnitude of its technological clearance at least and no more than a millimeter.
• Swap fuel using a button (or lever) of swinging. If it is on your trimmer model. Press the button every 4 seconds.

Now try to start the motor. Close the air conditioning immediately after starting.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

• The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;
• Lay two washers between which a spring is placed;
• Put in place a cup of antennae;
• Twist the screw (photos below).

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. It is better to repair qualitatively as quickly as possible.

If the motor does not start or works incorrectly

The reasons that the motor does not start with a two or four jerks of the manual starter cable can be:

Most often this is due to the incorrectly executed trimmer starting when the procedure for action is violated or some important point is not executed, Therefore, it is enough to properly launch and the motor will work. If the mower is poorly started after storage, then most likely, old gasoline is exhausted, so it is enough to change it.

If all actions are performed correctly, but there is no positive result, Contact the workshop or do diagnostics or repair yourself.

Starting benzokos for the first time or after long downtime

Motokos differs from a trimmer in that the trimmer line is not a trimmer line, but a mechanical gearbox or a swan based on the gears equipped with a knife. The knife drive is much more powerful than the forest mechanism. A powerful benzo.Oxy is also used when cutting the bushes. Both Chinese and European benzo.Cards do not differ in anything special when the declared capacity is real.

We start a trimmer (motorcycle) after winter

For lubrication of gear gears, Litol or solidol is used. Having checked the gearbox, prepare for the work and the engine itself. According to the above instructions. If the start has failed, the problem is already in the engine.

Preventive measures

In order for the acquired trimmer to be in good condition, it is necessary to use and store this unit as correctly as possible. Manufacturers recommend thoroughly observing several elementary rules:

• Pour gas tapers into the tank only high.Quality fuel.
• Regularly and timely conduct a technical inspection and adjustment of the main mechanical elements of the device.
• Try to avoid strong overload of the trimmer during operation.
• After each use, check the benzoocos for the absence of soot and specific oxidation on the surface of the ignition system mechanisms.

So that the trimmer is always in working condition, you need to prepare it as much as possible for storage in the cold season. First of all, you should put the unit in stages, and then perform a full cleaning and neat flushing of components. Thoroughly examine multifunctional blocks for the absence of any damage. If necessary, eliminate the deformation of the parts.

For storage, benzokos must be filled with a sufficient amount of oil. Mandatory cleaning of the air filter is mandatory, you can also disassemble and rinse the engine engine. All mechanisms are thoroughly dry, and moving mechanisms are lubricated with a high.Quality tool. To process the piston system, you should first remove the spark plug. The piston is neatly moved to the extreme position to be able to pour a small amount of oil into the candle hole and make a smooth scroll of the crankshaft.