How to get a Patriot Garden chainsaw. Patriot PT 5220 semi -professional chainsaw

Easy launch of a chainsaw what is it

Why do you need a preliminary pumping pump for fuel?When you press the pumping part of the preliminary pumping of the fuel, the fuel mixture pumps up and fills the carburetor. The launch of an unheated engine will be made faster. (Preliminary fuel pumping pump is installed on the Patriot Garden 2512; 3816; 3818; 5518).

What is the difference between nylon and felt air filter?The nylon filter, as a rule, reusable use, is easily cleaned and cleaned with pollution, but if large sawdust is accidentally hit, it is damaged. The felt filter has higher resistance to mechanical damage, but when it is polluted, cleaning does not always lead to the desired result. (All Patriot Garden models are equipped with a nylon air filter).

What does the number of fists affect the clutch coupling?A larger number of fists provides a more reliable adhesion, minimizing its slip. The load on the clutch cup is carried out more evenly. (All Patriot Garden models, except for 2512 are equipped with a 3-fist clutch).

Why do you need vibration protection?When sawing, a small vibration occurs from the engine operation and from the contact of the saw chain with wood. The vibration system helps to significantly reduce the sensation of these vibrations by the operator. (All Patriot Garden models are equipped with vibration protection).

What is an adjustable oil pump?The adjustment of the oil pump affects the amount of lubricant supplied to the saw tire. When used on a chainsaw of saw tires of different sizes, it becomes necessary to optimize and adjust the supply of lubrication, t.e, the longer the saw tire, the more lubrication it needs. When sawing various types of wood, there is also the need to adjust the amount of lubricant supplied. (All models of Patriot Garden, except 5518, are installed adjustable oil pump).

Why do you need a small hole on the tip of the saw tire?The hole is designed to lubricate the roller bearings of the driven star. T.to. The load on this node is large during sawing, it is recommended to make grease before the saw using a special syringe-oil. In the absence of lubrication, there is a high probability of jamming of roller bearings. (Saw tires of all Patriot Garden models are equipped with a lubricant).

Why do you need an inertial circuit brake?In the upper part of the tip of the saw tire there is a sector of 90 °, when sawing which there is a reverse rebound of the saw towards the operator. To prevent injuries, an inertial brake is provided, the inclusion lever of which, when rebound, is automatically turned on by the wrist of the right hand. The mechanism is triggered, the saw chain instantly stops. (All Patriot Garden models are equipped with an inertial chain brake).

What are the pluses of the engine with a chrome cylinder?The chrome coating serves to increase the service life of the engine, t.To chrome, a very durable material, resistant to high temperatures, has good frictional properties. Cylinders covered with chromium, are widely used in a benzo tool intended for professional use. (All models of Patriot Garden are installed chrome cylinders).

What is the difference between one and two piston rings in the engine design?Engines, in the design of which one piston ring is provided, have a higher overclocking rate and have a higher acceptance. Cylinder wear occurs slower due to a small contact area. But such engines are very sensitive to fuel quality. Engines, in the design of which two piston rings are provided, have an acceleration speed and acceptance lower than that of engines with one piston ring. Cylinder wear occurs faster due to the increased contact area and higher friction. Sensitivity to fuel quality below. (All engines of the Patriot Garden models except 2512; 3816; 3818 are equipped with two piston rings).

What is a “easy launch”?Chainsaws equipped with starters with a “light launch” system have a special mechanism with two platoon springs in their design. When pulling the launching cord, a significantly smaller attached force is required. The start of the engine will be made much easier. (Models Patriot Garden 3816; 3818; 4016; 4018 have a “easy launch” system).

What remains to our client of the chainsaw “STIHL” have two.stroke engines. Their cool start is carried out according to a similar method. But on sale there are models on the pages of which there are additional equipment, thanks to its use, you can start a saw without making special efforts. Therefore, the start methodology may differ.

The algorithm of the saw establishment “Stihl 180

If the question arose for you what, how to start a stihl chainsaw, then this process can be seen using the example of model 180. To be able to perform work on cool, you need to enable the ignition and install the engine control lever in the lower position. With all this, the carburetor damper will block the air from the filter, and the throttle will be open, because the fuel mixture will be enriched.

Starter handle must be pulled a couple of times until the 1st flash occurs. This will indicate that the mixture entered the cylinder, and the equipment is ready for the establishment. Before starting the stihl chainsaw, you need to install the control lever for one position upward. Here the air damper will open, while the throttle remains in this matter.

The starter must be pulled and started. The tool works at high speeds, the throttle will be open. To install the latter in the idle mode, use the gas trigger and release it. With all this, the tool should start working normally. There are no additional devices on the described model of the chainsaw that would facilitate the launch.

Advantages and disadvantages of the chainsaw Patriot Pt 2512

• derived from production;
• After each use, you need to pull the chain.

Basic equipment

Factory basic set of the chainsaw Patriot PT 2512:

Optionally, it can be equipped with mittens for work (at the discretion of suppliers).

Specifications

The main technical parameters of the chain gasoline saw Patriot PT 2512:

• There is a circuit auto sculpting function;
• Tire 30 cm;
• engine volume 23 cubic meters.cm;
• oil tank. 200 ml;
• fuel tank. 200 ml;
• chain with 3/8 step “;
• chain for 44 links;
• tire groove 1.3 mm;
• the weight of the chainsaw is 2.9 kg;
• Warranty period. 12 months.

How to start a chainsaw: Features of proper operation

Many buy chainsaws for the first time without experience with this tool. Despite this, to learn how to work as a tool, there is no need to take special courses. After the purchase there is a great desire to quickly test the tool in work. To do this, be sure to get acquainted initially with the instrumentation instructions, as well as safety measures when working with a chainsaw. In the material, we consider how to properly start a chainsaw, as well as work with it.

How to start a chainsaw: Preparation for launch

Every master who has a chainsaw should know how to start it correctly. Initially, it should be noted that to start the tool, it must be seasoned with fuel. For this, not just gasoline is used, but a gasoline mixture.

It’s important to know! Pure gasoline for the functioning of chainsaws cannot be refueled. It is necessary to refuel exclusively a mixture of gasoline with appropriate oil for two.stroke engines.

First you need to figure out how to prepare a gasoline mixture correctly. These proportions are naturally indicated in the instructions, but since few people read them, this issue should be considered in detail.

As fuel, gasoline of the AI92 brand and above is used. It will also be necessary to use the corresponding oil, which can be purchased in the same place as a chainsaw was bought. The proportion of gasoline and oil is 1 to 50, after mixing which, it is necessary to thoroughly stir. In this case, it is necessary to prepare the mixture in a separate container (plastic bottle), since it is not only convenient to store the prepared fuel mixture in it, but it is also convenient to refuel the tool in the tank through the small diameter of the gas tank hatch.

Pour the cooked mixture in the fuel tank, the cover of which is indicated in the form of an image of a gas station. This is very important, since the chainsaws have two similar tanks. The second tank is intended for filling the oil, which is consumed for lubricating the tire and chain during the functioning of the tool.

It’s important to know! After refueling the fuel to the gas tank, do not rush to start the tool. It is also necessary to refuel oil into an oil tank to prevent the chain overheating, which as a result can cause damage to it.

As an oil to lubricate the chain, it is recommended to use special branded or motor oil for the car, but in no case do not practice. If you see how your neighbor refueling in a chainsaw, then you should not repeat its mistakes, as this significantly reduces the service life of not only the chain, but also the tool itself.

It is always necessary to control the level of oil and fuel mixture in tanks, but it is recommended to carry out refueling according to the following scheme:

• The fuel mixture in the tank is filled to full.
• At the same time poured to full and oil for lubrication of the chain.
• The oil consumption and fuel mixture is approximately the same, so both tanks are recommended to refuel simultaneously.

How to start a chainsaw: launch features

After the tool is ready to launch, you can start. The process of launching a chainsaw is as follows:

• First, the chain tension is checked. It is required to try to raise the middle links of the chain in the upper part of the tire with your hand. If the chain stretches with an effort, then everything is in order, if it is easy, then you need to tighten it. Do not overdo it, since the excessive tension of the chain is also extremely not desirable.
• Checking for a hauling. If after pulling up the chain there are doubts about its plugging, then you can check the correctness by rotating it manually on the tire. The chain should rotate normally without stretch.
• Installation of a hand brake. The hand brake of the chain is located in front near the upper handle to hold the tool. If you squeeze the lever forward, then after starting the chain will not rotate, and when returning to the opposite position, the cutting product will begin to move. Before starting, you need to put the tool on the brake.
• Fixing the tool on a flat surface and starting. So that when starting the tool does not twitch, it is necessary to take the top handle with the left hand, and rest on the lower handle with the right foot. The chainsaws are fixed, now you can turn on the ignition button, put forward a throttle, then pull from 2 to 5 times per handle of the starter. While pulling the handle, the engine should give the first flash 2-3 times indicating that you can push the throttle and launch. Twing the starter handle must sharply, then immediately return it to its original position, without detaining in an elongated position.
• Removing a hand brake. As soon as the chainsaw starts up, it should be allowed to work for 1 minute without rotation of the chain with medium.sized processing. The engine will have time to warm up, after which you need to squeeze the hand brake. If a hot engine is launched, then you can start work immediately after starting.
• Checking the availability of oil supply. To do this, you need to bring the file to a sheet of paper and go out, after which traces of oil should appear on it.

How not to ditch a chainsaw at the first launch? Instructions for beginners

Our article is intended for everyone who will have to use the chainsaw for the first time in the near future. What to hide: this is not the easiest to use the technique. Of course, there is an instruction But only if you have never seen before someone prepares for work and starts a chainsaw, this instruction will seem to you a filkin letter. So what to do? What you need to know and be able to not break the saw at the first launch? Let’s figure it out!

The most important thing is to correctly install a saw set

What is a saw set? This is the name of the guide tire and saw chain. Here is the main sequence of actions when installing it:

1) we put on gloves to protect your hands from cuts with a chain;

2) unscrew the nuts of the cover cover cover and remove it from the tool;

3) put the chain on the leading star, taking into account the direction of the edge of the teeth (it must correspond to the direction of the circuit);

4) set the tire in place and “put on” the chain on it;

5) return to the place the cover of the brake of the quapi and twist its nuts with the hand;

6) pull the chain with a special key. How to understand that the chain is stretched correctly? Try pulling it away from the tire. It should go by no more than 1 cm. What is terrible weaker stretch? When working saw, the chain can bounce and seriously injure the user. Strong stretch when the chain is stretched like a string, in turn, fraught with a quick breakdown of a saw headset.

Now it’s time to season the chainsaw. First you need to prepare the fuel mixture. In the vast majority of cases, it is made in a ratio of 1: 40 (that is, approximately 25 mg of oil for a two.stroke engine per 1 liter of gasoline). The finished mixture should be tucked into the fuel tank using a funnel.

Gas station refueling and launching

The chainsaw has two containers. Oil lubricant tank. closer to the bus. The lubricant should always be present, check its level at each refueling fuel mixture.

Normally, during the operation of the chainsaw should spray a little grease. This means that it is supplied to the chain in sufficient quantities.

The fuel mixture is poured into another tank. It consists of gasoline (for us it is AI-92) and special oil for two-stroke engines (2T). Make the mixture in the proportion of 1 part of the oil for 50 parts of gasoline. That is, 1 liter of gasoline requires 20 ml of oil per 1 liter.

A few more points in refueling:

• It is not recommended to store a fuel mixture of more than one month. Therefore, do not cook it for the future.
• Refuel the saw again after the engine cools
• Unscrew the cover of the fuel tank smoothly so that the excess pressure in the tank falls gradually.
• Close the tank cover tightly, otherwise the cork can be unscrewed due to vibrations.
• The tank contains a suction head, which is equipped with a filter. This head needs to be changed annually.

So, the saw was collected and seasoned. We can start.

• Check again whether the chain brake is installed. squeeze it forward. Set the brake when completing the work will be a good habit.
• Direct with the instrument from the dressing site. Starting, like sawing, should be carried out in the open air.
• If the saw has a decompression valve. click on it, if there is a fuel pump. pump up fuel.

Squeeze the blocking of the gas lever and lower it into the throttle position (closed air damper) combined lever.

Set the saw on a flat surface and it is best to crush it with your foot by the handle behind, and grab the upper handle with your hand.

Pull the starting cable up evenly, without a jerk. Repeat the movement until the saw has a short time (this lasts less than a second).

After a short.term start.up of the engine, immediately open the cloak of the combi. raise up one position.

Pull the starting cable again until the engine starts. Try to do a cable movement vertically up so as not to wipe the surrounding details. The engine started. click once on the gas lever, the combination of the combination will independently rise to the idle mode. The chain should not rotate because the chain brake is installed.

Raise the saw and holding on to the handles. Pull the chain brake to yourself with your fingers. The chain will begin to move.

Check the performance of the lubricant system. Give full gas over a light background. wood, a piece of paper. Oil drops should appear on the surface. If this happens, the chain is lubricated correctly.

You can start work. Saw wood on full gas!

In the cold season

Winter launch is no different from the usual. The only thing that the tool should be allowed to work at idle. And, of course, do not store it in the winter of frost, as well as components for the fuel mixture.

And yet, usually the chainsaws occur long winter downtime. So that she feels cheerful in the new season. prepare her correctly for storage.

• Drain the fuel from the tank. Make a saw so that gasoline is developed
• Remove the tire and circuit. Clean them and spray with protective lubricant. For example, silicone.
• Clean all available and removable elements. Especially the air filter.
• Put the saw in a special case, or any package that protects it from dust.
• Keep the tool in a dry room.

Badly starts on cold

The answer on this question is unequivocal. there is no compression. This happens. rings, most likely through long operation, simply worn out, therefore, when you are trying to start the device directly in the cold state, then there is not enough compression for direct starting.

Why the chainsaw is not started.Cause.How to eliminate.

But given the fact that most people of the “literate” begin to systematically pull the pen, at that time the rings are friction about the sleeve, therefore, they get oil with gasoline, the degree of compression increases and the engine is launched. And when the chainsaw was already heated, of course she will begin to start.

But this kind of manipulation is quite harmful to the device, since just several times you will achieve the desired effect through such actions, but the time will come when the chainsaw may finally break off. Therefore, the best that you can do is change the rings that are already worn out. This is not a complicated process, so you can completely cope with it yourself without the use of service services.

Why not start hot?

Before starting to solve this problem, it is necessary to note that the productive and correct operation of the engine depends primarily on speed by applying the starter mechanism. In most models, this level of “minimum” is eight hundred revolutions per minute. It is important that the main cause of the “non.plant” of the chainsaw is the usual flooding of the engine.

In order to eliminate this problem, it is necessary first of all the damper (air) to put in the middle position. After that, blow a chainsaw a couple of times. The working chainsaw is started to start poorly, the Patriot RT-3816 did not drink. After the process has gone, warm it within ten seconds, and then transfer it to the move (idle). After conducting these manipulations, you can completely open the damper (air).

After that, it is worth noting that before starting the direct performance of actions regarding “prescribed recommendations”, try to launch the device directly in the idle position. To do this, just pull the “rope”. Since in that case not a hot engine, then the plant will produce without any problems.

But if you can’t do anything, it means that it is already quite cooled. In this case, fix the half.gas regarding the requirements in the instructions that are attached to your chainsaw.

But if this does not help, in this case, you should directly scroll through the cold screw, directly clockwise.

Remember that the larger the speed level in your device, the easier it will be for you to start the device. What are the reasons why the chainsaw is not started and how the Chinese does not start. And remember that the chain relatively cold move should be motionless.

How to start a chainsaw: Preparation for launch

Every master who has a chainsaw should know how to start it correctly. Initially, it should be noted that to start the tool, it must be seasoned with fuel. For this, not just gasoline is used, but a gasoline mixture.

It’s important to know! Pure gasoline for the functioning of chainsaws cannot be refueled. It is necessary to refuel exclusively a mixture of gasoline with appropriate oil for two.stroke engines.

First you need to figure out how to prepare a gasoline mixture correctly. These proportions are naturally indicated in the instructions, but since few people read them, this issue should be considered in detail.

As fuel, gasoline of the AI92 brand and above is used. It will also be necessary to use the corresponding oil, which can be purchased in the same place as a chainsaw was bought. The proportion of gasoline and oil is 1 to 50, after mixing which, it is necessary to thoroughly stir. In this case, it is necessary to prepare the mixture in a separate container (plastic bottle), since it is not only convenient to store the prepared fuel mixture in it, but it is also convenient to refuel the tool in the tank through the small diameter of the gas tank hatch.

Pour the cooked mixture in the fuel tank, the cover of which is indicated in the form of an image of a gas station. This is very important, since the chainsaws have two similar tanks. The second tank is intended for filling the oil, which is consumed for lubrication of the tire and chain during the functioning of the tool.

It’s important to know! After refueling the fuel to the gas tank, do not rush to start the tool. It is also necessary to refuel oil into an oil tank to prevent the chain overheating, which as a result can cause damage to it.

As an oil to lubricate the chain, it is recommended to use special branded or motor oil for the car, but in no case do not practice. If you see how your neighbor refueling in a chainsaw, then you should not repeat its mistakes, as this significantly reduces the service life of not only the chain, but also the tool itself.

It is always necessary to control the level of oil and fuel mixture in tanks, but it is recommended to carry out refueling according to the following scheme:

• The fuel mixture in the tank is filled to full.
• At the same time poured to full and oil for lubrication of the chain.
• The oil consumption and fuel mixture is approximately the same, so both tanks are recommended to refuel simultaneously.

How to start a chainsaw: launch features

After the tool is ready to launch, you can start. The process of launching a chainsaw is as follows:

• First, the chain tension is checked. It is required to try to raise the middle links of the chain in the upper part of the tire with your hand. If the chain stretches with an effort, then everything is in order, if it is easy, then you need to tighten it. Do not overdo it, since the excessive tension of the chain is also extremely not desirable.
• Checking for a hauling. If after pulling up the chain there are doubts about its plugging, then you can check the correctness by rotating it manually on the tire. The chain should rotate normally without stretch.
• Installation of a hand brake. The hand brake of the chain is located in front near the upper handle to hold the tool. If you squeeze the lever forward, then after starting the chain will not rotate, and when returning to the opposite position, the cutting product will begin to move. Before starting, you need to put the tool on the brake.
• Fixing the tool on a flat surface and starting. So that when starting the tool does not twitch, it is necessary to take the top handle with the left hand, and rest on the lower handle with the right foot. The chainsaws are fixed, now you can turn on the ignition button, put forward a throttle, then pull from 2 to 5 times per handle of the starter. While pulling the handle, the engine should give the first flash 2-3 times indicating that you can push the throttle and launch. Twing the starter handle must sharply, then immediately return it to its original position, without detaining in an elongated position.
• Removing a hand brake. As soon as the chainsaw starts up, it should be allowed to work for 1 minute without rotation of the chain with medium.sized processing. The engine will have time to warm up, after which you need to squeeze the hand brake. If a hot engine is launched, then you can start work immediately after starting.
• Checking the availability of oil supply. To do this, you need to bring the file to a sheet of paper and go out, after which traces of oil should appear on it.

Having launched a chainsaw, you can proceed to the performance of work on sawing wood.

It’s important to know! The material describes the process of starting the tool, after which you can start working with it. Do not forget that if you bought a new chainsaw, then it should initially run in.

Carburetor adjustment

During operation, you may need to adjust the carburetor of the chainsaw “Patriot-3816″. The adjustment is divided into 2 main stages. The first is basic and is carried out when the engine is turned on. The second will need to be performed when the engine warms up.

For the configuration procedure, you should familiarize yourself with the instructions. At the first stage, the adjusting screws of high and low revolutions turn clockwise until you find the highest resistance. As soon as the screws reach the stop, they should be translated in the opposite direction and stopped with 1.5 turnover. Now you should turn on the engine for average speeds and warm it within 10 minutes.

The idle screw should be moved clockwise. It can only be omitted when the motor comes into stable operation mode. The chain should not move during this. In idle mode, the motor may stall. In this case, you need to bring the adjusting screw to the stop clockwise. You may encounter the chain to move. The adjusting screw must be turned in the opposite direction.

The cost of spare parts

In the process of its operation, you may need spare parts for the chainsaw “Patriot-3816″. A hand starter can be purchased for a 650 chain tensioner will cost you a 107 ignition coil you can buy for 1100 welded tire. for 1050 flywheel costs 450, the deflector. 194, and candles. 80. The carburetor will cost the consumer in 690 a leading asterisk can be bought for 330

Before starting the operation of the chainsaw, you must realize that the resource of the tool is determined by you. To do this, properly distribute the loads and allow the tool to rest. Bennesopila loves care.

The unit will be ready to last longer and surprise you with ease of work if the working body is clean and well lubricated. The sawing part has its own work resource. The tire can survive two chains. As a rule, the chain serves for 2-3 sharpening. After that, you need to part with her.

Many buy chainsaws for the first time without experience with this tool. Despite this, to learn how to work as a tool, there is no need to take special courses. After the purchase there is a great desire to quickly test the tool in work. To do this, be sure to start initially with the instrumentation instructions, as well as safety measures when working with a chainsaw. In the material, we consider how to properly start a chainsaw, as well as work with it.

The consequences of operation on a rich and poor mixture

Confirmation of normal, in a proportion of 16: 1, the quality of the air fuel mixture is the brown color of the insulator and the absence of traces of soot.

Condition of the air intake and muffler

The cause of the problem launch may be the filter of the air cleaner clogged with sawdust. If the engine starts with the air intake removed, special attention should be paid to cleaning the filter. A large amount of soil in the muffler is reflected in the power and thrust of the power unit, but the engine should be launched without much effort.

When the threaded fasteners are weakened, an air leak is formed, which leads to the depletion of the gas-air mixture and, accordingly, the deterioration of its working characteristics.

To replace the damaged gasket, it is recommended to use the repair kit, in its absence, the gasket can be made from the elegant benzo-grease material in the thickness of the thickness.

Rules of care

To extend the life of the chainsaw, it is necessary to properly care for it. In particular, it must be provided that all the details change in a timely and lubricate.

This is what you should pay special attention to:

• It is imperative to use high.quality oils and gasoline, and you need to dilute them in the proportion, which is recommended by the manufacturer. Otherwise, the power of the motor will drop sharply.
• The air filter is periodically required to clean from wood dust. When working using a swept chain, the speed of dust collecting in filters is very high. As a result, less air is received, due to which fuel consumption increases, a candle clogs and problems begin with the launch of the saw.
• Adjustment several times a year. It is necessary to check the main nodes of the tool so that they work stably and are in an efficient form.
• The cutting system should not be overly stretched, but you can’t hang free either freely. Before each cutting of the tree, it is recommended to check the amount of lubricant material. Sometimes sawdust can clog the supply of lubricants. If the oil is present, then it is easy to check the presence of a blockage.
• Stretch circuits should be quite sharp. It is necessary to periodically sharpen the specialist.

List of the most popular models Patriot

PT 3818

This is a good household model, the device is convenient to use and has a small tire diameter. That is, you can saw thin branches, shrubs and small trees.

Here are the main advantages of this tool:

• A light weight.
• Good balancing.
• Walbro motor is used, which guarantees a long service life.
• There is a chain brake.

• The lubrication of the chain is automatically.
• Vibration insulation facilitates the work.
• A fairly large tank (0.21 liters) allows you to work for a long time without refueling.

There are no objective shortcomings, but it must be understood that the tool cannot be used for industrial purposes, it is intended only for domestic use.

PT 445 The One

This is a universal tool with a fairly wide range of use.

Its main advantages include:

• Reliable fastening of the air filter cover using special latches.
• Improved air purification system.
• The tank covers can easily be unscrewed using a screwdriver.

• There is a primer of pumping for a quick “cold” launch.
• The switch is large enough.
• Low).

From the shortcomings, users note that the shutdown button is large, so during operation, you can accidentally click on it. Some also claim that the chainsaws are poorly balanced compared to a number of other Patriot models of a more expensive segment.

PT554 Pro

This is a semi.professional tool that can be bought on the market for about 14 thousand. He has a large margin of strength, excellent balancing, as well as a pleasant design.

Users note the following advantages of this chainsaw:

• The presence of the Easy Start system.
• There is a primer for a “cold” launch.
• The inertial circuit brake guarantees safe operation.

• The wide base of the handle on the rear panel will protect yourself from unforeseen cases.
• Work at temperatures up to. 40 degrees.
• The file of the Oregon.

Most users note that they are satisfied with the goods. But some write that gasoline is consumed very quickly. You also need to tighten the chain after several cuts. However, it must be understood that over time, fluid consumption increases. This is a natural process, which can be dealt with by systematic replacement of components, the quality of which has significantly decreased.

PT6220

Another semi.professional chainsaw Patriot, which copes with most of the tasks. It can be used to harvest firewood and during construction. She has a large power supply, but the tool is quite noisy. Its in the market.

Many users value this model for:

• Ergonomic pen. It has a chainsaw control lever and a shutdown button to prevent the device’s accidental trigger.
• There is a side handle to make it more convenient to hold the unit.
• Excellent balancing.
• High performance due to the use of a powerful engine.

• Oregon tire and chain. This guarantees a long service life.
• There is an inertial circuit brake.
• Fuel for 0.35 liters.
• For the possibility of working for a long time, vibration isolation is provided.

Many users note that this tool for strong people. Large weight does not allow you to keep a chainsaw for a long time, you need to give your hands a rest. Some more write that over time the unit starts worse and strongly fills the tire with oil.

PT541 Pro

This device can also be attributed to semi.professional.

Many users write positive reviews about the tool, indicating the following advantages:

• Easy Start system.
• The presence of an air cooling system of the motor.
• There is a primer.
• Inertial brake of the chain is provided.

• Wide base of the rear handle.
• The possibility of operating before.40 degrees.
• Using Oregon saw

Thus, this is a reliable device that should be used for household purposes and not only. A relatively small price allows the chainsaws to fully recoup itself with commercial use. The device does not have objective disadvantages. Vibration insulation allows you to use it for a long time.

PT 3816 Imperial

This semi.professional power device 2 l.With. will quickly prepare firewood for the winter and solve other current problems where chainsaws are needed. You can buy this tool for about 8,000.

The main advantages include:

• Democratic price.
• Ergonomic design.
• The presence of the Easy Start system.
• Vibration isolation.
• Fuel tank by 0.21 liter.
• Chromation of the walls of the cylinders, which reduces the friction of the elements and extends the life of the product.
• Good balancing.

Some users in the reviews note that this is a good chainsaw for their money, but she has several drawbacks:

Thus, users recommend this chainsaw, and they also indicate that it can work for a long time without replacing components. One user indicated that he worked for about 2 years before repairing the tool engine.