How to insert a nozzle into a puncher. What to do if the drill does not move

How to change the nozzle on a perforator

The popularity of the question of how to insert a drill into a perforator or electric drill is explained quite simply: such devices are actively used both in industrial and domestic conditions. Cartridges are different, as well as nozzles fixed in them

An incorrectly installed drill can lead to a number of problem situations:

  • The impossibility of working with a perforator or drill;
  • Obtaining uneven holes with a broken inner surface;
  • I will fly out, which is fraught with serious injuries.

Despite the fact that it is not so difficult to insert a drill into a perforator or drill, it should be responsible for solving this issue.

Proper installation of a drill in a drill cartridge

Before dealing with how to correctly install a drill in a perforator, it is advisable to find out how to insert a drill into a drill. The element of its design, in which the shank of the drill is fixed, is the cartridge. On most models of modern drills, cam.Type cartridges consisting of: consisting of:

  • Cylindrical body;
  • Rings or sleeves that rotate around the outer surface of the case;
  • Kulachkov installed in the inside of the corps.

When the sleeve rotates clockwise, the fists simultaneously approach each other, thereby reliably clamping the shank of the installed drill. Accordingly, the question of how to pull the drill out of the drill is not difficult to solve: it is enough to start rotating the sleeve counterclockwise. In this case, the fists will begin to diverge, which will make it easy to remove the drill from the drill. It should be borne in mind that before installing the fist of fist should be unclenched with a margin, in which case the tool can be easily inserted.

The convenience of using cam type cartridges lies not only in the efficiency and high reliability of the installation of the tool, but also that they can insert the drill of almost any diameter in them. When using such cartridges of difficulties with how to change the drill into a drill, as a rule, does not arise. The correctly inserted tool is kept in such cartridges and allows you to drill the exact hole.

If you began to notice the slippage of the teeth at the time of tightening the cartridge, replace the erased key with a new

Cam cartridges are used in both industrial and household tools for drilling. Clamping devices of household drifts are available for two ranges of drill diameters: from 0.8 to 10 and from 1.5 to 13 mm.

insert, nozzle, drill, does, move

Unboxing and how to use Maxmech Electric Drill ED 750-10

The design of the fist cartridges may include two different methods of the clamping of the tool: key and quick.And.Sounding.

In the first case, the sleeve is driven using a special key, on the conical working part of which there are teeth. The key to drive the clamping mechanism, it is necessary to insert into the holes on the side of the cartridge case and rotate. Such holes in individual models can be even three. Accordingly, in order to weaken or hold fists, the key must be inserted into each of them and start rotation counterclockwise or on it.

After weakening the cams, using the key, it is necessary to turn counterclockwise and the cartridge itself, which will increase the distance between the cams to the required value. The inserted tool is fixed in the reverse sequence: first the cartridge itself is clamped (when it rotates clockwise), and then the nests are clamped with the key.

Pulling out and installing drills when using a fast.And.Packed cartridge is much easier and faster. In it, the sleeve is driven by manually. To limit the power of tightening the cams, they are often equipped with blocking elements.

Before inserting the drill, first make sure that the drill is in working condition and de.Energize it. Only after that you can start installing a drill.

Checking serviceability

Before inserting and fixing the drill in the perforator, you need to make sure its performance. For this, the tool is included in the network, put in the drilling mode without impact, and then press the start button. If there are no extraneous sounds, uncharacteristic smells, then the unit is ready to work, and you can take up the installation of a storm nozzle.

A few tips for using a drilling tool

In order not to encounter the fact that a flying tool or concrete crumbs will harm your health, drilling must be performed in compliance with all safety measures. As a means of ensuring such safety, you should use protective glasses, gloves, bears or headphones that protect the organs of hearing. Naturally, all work must be performed in special clothing in which there should not be hanging elements that can be wrapped in a drill.

To exclude overheating of the electrical tool used to drill, it is necessary to regularly give him rest. It is very important to insert the drill correctly (you need to do it all the way).

Two methods of a clamp of a thin drill cartridge, if the fists do not reach the shank a little

If the drill is stuck in the wall during the drilling, then it should be removed without removing the tool from its surface. To do this, the drill must be removed from the perforator and insert another, with which it is necessary to begin to destroy the wall around the drill stuck in it.

How to insert a drill

The perforator itself also has a fast.Packed mechanism. Reliable fastening of the drill in it is provided with fixation using special balls, which, when closed, are tightly included in the grooves on the lower part of the drill.

In order to fix the necessary nozzle, whether it is a drill or crown, you need:

  • Take the lower part of the cartridge down (towards the perforator);
  • Holding it in this position, insert the right nozzle;
  • Let go of the cartridge.

And to insert a drill into a punch with an adapter, first fix the removable cartridge, which has a mount with grooves for the tool. Then the drill is installed directly. To pull out a drill or drill, you need to perform all the above actions again.

Here I would like to note that any manipulations for the installation and removal of a drill or other nozzles are preceded by a check of the working condition of the perforator mechanism. To do this, the unit must be included in the network and, having set the necessary operating mode, click on the start button. If the unit does not make unusual sounds and at the same time does not feel the extraneous smells of Gary or burned plastic, then the tool is ready to work.

If the drill is stuck

It happens that in the process of working on time, an unlucky shank leads to jamming. The fixing mechanism is stuffed with dust from drilling, and the drill cannot be pulled out. What to do in this case? No need to panic or immediately run into repairs. Using penetrating lubricants will solve this problem. These funds are produced in aerosol cans and have a low consistency. Therefore, they act in places that are inaccessible. To pull the drill, you need to inject the lubricant directly for the drill and leave the tool at rest for 10-15 minutes. Then smooth, swaying movements to remove the boat.

You need to remember that before inserting the drill into the punch, you need to lubricate the shank. This will save the cartridge for many years.

How to insert a drill into a perforator quickly and easy

The ability to work with a drill or drill is basic today. Below we will describe how to insert them correctly into a perforator.

To date, the tool uses the SDS cartridge. Its feature is that it does not require the presence of a key. Unlike a cam cartridge, the process of removing and installing the drill takes a couple of minutes. It is necessary to sequentially do the following:

  • Lower the cartridge down, holding the base
  • Insert the lower end of the drill into the hole
  • Release the cartridge, the spring will fix it on the starting place, the fixing balls will tightly fix the cutter
  • Check the drill fixing in the cartridge, pulling it down. Any backlash should be absent. The maximum permissible distance to which the drill should not exceed one centimeter
  • If a fist cartridge is installed, the drill is mounted by rotation of the cartridge, while the thread is delayed
  • We are waiting for a complete stop of the rotation of the cartridge
  • Pull it down
  • We take out the drill itself
  • Let go of the cartridge, the spring returns it to its place.

Attention! As a result of friction on the working surface, the metal metal is very hot, it is necessary to use gloves to prevent skin surface burns.

The reasons for jamming the drill in the perforator

The need to remove a drill from a perforator occurs when a nozzle is replaced, but sometimes it is impossible. The reason for the wedge is the use of cheap drilling tips. Typically, from the end of the shank they are flooded by a boy (shock bolt), because they are made of low.Quality metal, which is not able to withstand high shock loads. They also bend, twist, break and amenable to other mechanical deformations.

Damaged shank.

How to insert a spatula into the SDS-Plus cartridge

Before inserting the shoulder blade (or drill. Instead of the shoulder blade can be any tool) into the cartridge, it is necessary to wipe the cartridge and the shoulder blade with a cloth to remove the old grease with dust. (The cleaner the tool will be, the longer it will last.)

Check if there are no damage to the rubber parts of the cartridge. With their damage, dust penetration is possible. As a result. Premature failure of the tool and repair.

Be sure to apply a lubricant to the back of the scapula, as shown. If this is not done, the wear of the perforator will be incredibly fast.

Insert the shoulder blade into the cartridge to a characteristic click. Try to take it out, just pulling in the direction from the punch. If it is not taken out, then you did everything right.

You can do all of the above yourself by taking a punch in our company.

Drill for a perforator: how to insert, remove, fix

With the advent of concrete reinforced structures, external and internal repairs cannot be performed without a perforator. A large number of models of different firms are presented on the market, these are Bosch, Makita, Sturm, Bison, Vorthe, Dexter, Interskol, Caliber, Metabo, Union. Despite the variety, the main nodes and mechanisms work almost the same. The process of reinstalling the working element is also similar. Before inserting the drill into the punch, you need to be able to get it correctly.

The perforator is Universal tool, which has great opportunities. There is a pneumatic device inside it, a pushing piston that comes into contact with a boy. The latter makes the equipment make reciprocating movements. As a result of the nozzles, any surface is destroyed. The presence of a function of the impact allows the tool to make holes in solid materials.

Its purpose depends on the built.In modes: drilling, d some and drilling. There is a toggle switch to switch the modes.

Manufacturers produce models different in weight:

Depends on the size of the perforator Power and shock force.

Rules for the safe use of the tool

To ensure safe working conditions and efficient use of the tool when working with a punch, a number of rules should be observed:

  • It is imperative to use personal protective equipment for the eyes, ears, arms and legs;
  • Conduct an inspection of the tool before each start of work;
  • When drilling long holes, it is necessary to start with short drills and drilling gradually;
  • Long.Term continuous work leads to overheating of the gearbox and an anchor winding. In this case, the perforator must be given to cool. The permissible duration of work in idle and under load are indicated in the tool passport or in the operating manual;

With an experimentally, the temperature of the heating of the gearbox and the engine can be determined by the degree of heating of the perforator body. The case should not be clearly hot, the characteristic smell of the burning electrical insulating material should not come from it.

  • Observe the lubrication mode of the shanks of the drills. This should be done with a lithol or solidol every 150-200 drill operations performed. Some sources recommend lubricating the shanks of the drills with each installation of the drill in the cartridge;
  • Timely perform the maintenance of the tool. The volume of maintenance work and its frequency are indicated in the passport of the perforator;
  • If materials of increased hardness are processed, it is necessary to use the liquid cooling of the hole;
  • With intensive work, periodically cool the drill. The metal of the working tool (drill) when overheating irrevocably changes its mechanical properties (hardness, elasticity). If you do not cool the drill in a timely manner, it will become unsuitable for further work. There is no standardization of the operating time of the drill. It depends on the effort attached to the perforator, the material that is drilled, drilling intensity, etc. It is extremely dangerous to determine the temperature of the heating of the drill with your hand. It is better to pay attention to the heat emanating from the perforator body. Overheated drills often change the color to a darker, sometimes with a blue tint.

How to work with a drill correctly?

The perforator has a fairly simple device for installation and dismantling the drill. Just squeeze the perforator’s head to the stop, and with the other hand, remove the drill freely. After that, let go of the perforator’s head. Likely, you can put the drill back.

Preparation of the punch for work

Before using the tool, it is necessary to study the instructions for its operation. It will not teach you how to work properly by any perforator, but will give a lot of information about the tool: features of preparation, service, subtleties of use and familiarize yourself with safety regulations.

Before turning on the unit fork to the network, it must be visually inspected. Such a measure will make sure:

CMMA LIVE BOXING CLASS. TYSON DRILLS

Will pistols work if stuck in concrete?

  • Lack of visible damage to the body, cartridge;
  • The integrity of cable insulation;
  • Lack of carbon deposits, oxides on contacts or pins, which are included in the outlet.

You need to make sure of the severity and serviceability of the nozzles. The cutting and fucking tool should be acute, do not have traces of damage: chips, deformations, cracks, scores of the shank, its collapse from the end. In case of nozzle problems, it should be sharpened or replaced with new. Use the chisel after aligning it on the anvil or tightening the riveted shank is strictly prohibited.

After the checks, the cartridge rotates with the hand. If everything is in order, a test launcher of the perforator is carried out at idle. In the presence of a speed controller, the maximum speed of the electric motor is set. Reverses and revolutions are checked in the presence of.

Tile removal nozzle

Removing old tiles for the flooring of the new is also a problem for a beginner. The same perforator can help out with a special nozzle selected for this. In general, if the tile itself is a stocking, it can be removed manually, but in other cases. As they say, at least tear off your teeth. To do this, it is better to use a punch with a shaber nozzle.

Punch with a tile removal nozzle

Tiles are removed, moving from the center to the edges, carefully, so as not to damage. If necessary, other material. Then a layer of glue or old concrete screed to the flat layer is removed then.

Shoulder blade and its purpose

The shoulder blade is also called the grocery chisel, as it has a similar design. A flat spatula with a wide tip is actively used in order to remove plaster from the walls, as well as to remove paint. To remove the plaster, perhaps there is no better power tool than a punch with a nozzle. In addition, the shoulder blade is also used to stroke the walls when you need to get a large channel for laying communications.

When working with a spatula, its tip is also blown away, which can be tidied on a special sandpaper. Typically, each perforator is equipped with devices such as peak, chisel and spatula, so it will be necessary to buy them in extreme cases when these tools fail or are lost.

How to squeeze a drill in a cartridge?

The way to fix the thin The drill in the cartridge weat or drills take the wire and wrap it tightly round to the turn on the tail drill, which will be clamped. Wrapped it up, and bite off the excess with bites. Drill Prepared for drilling.

Boers are used in cases where it is necessary drill a larger hole than a standard drill. The following types are distinguished Burov:. Ring: they, as and scapular drills are used to create wooden holes, but they can also process metal plastic.