How to insert line into the trimmer head

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• one groove. both antennae are wound together in one groove;
• two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
• A small section of the line is left free to bring it out. it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

Threading the line into the trimmer reel video

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Method 2. two segments

Two coiled line lengths

fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.

The end of each segment is folded

The end of each segment is folded.

How To Give Your Self A Side Part | How To Give Your Self A Side Part With Clippers

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We begin to reel the fishing line

They cling to it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.

The bottom line is reeling

The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.

The tips are threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

Preparing for replacement

We disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the brushcutter. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.

We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.

Stihl Line Trimmer- How to Quickly Exchange the Head in 20 seconds.

The spool consists of the following:

• Spring case
• Cover with locking latches
• Button coil

The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.

Disassembled trimmer spool

On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.

These holes are needed to fix the line when changing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.

Holes for fixing the line

There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for the outlet of the fishing line from the trimmer spool body (see the figure below).

Fitting on the holes of the line output

The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.

Two sections for line

First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.

Determining the required line length

Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.

Special designation on the reel

If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Bobbin case designation

How to wind the line around the trimmer cutter head or brushcutters

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

The guaranteed output of the factory trimmer refueling will inevitably require a line change. Having a very rough idea of ​​how to thread the line into the trimmer reel without the help of others, the newcomers are reluctant to take up this business. But with some abilities, mastering this simple science does not present any difficulties, and the similar annotation presented below will greatly facilitate Such a process.

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

• small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed simultaneously, the upper part of the reel, together with the inner content for winding the line, is disconnected, although the lower part remains on the trimmer. It is better to parse the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and does not even get lost;
• electronic and gasoline trimmers with a curved bar without the ability to install a knife, you have spools with a special lamb: in similar designs, hold the spool in a fixed position with one hand, and turn the locking reel on the bar with the other counterclockwise, the wing nut. After disconnecting the nut, the entire bobbin is removed.
• electronic and gasoline trimmers with the ability to install a knife on a straight bar (for example, Calm trimmers) have a hole under the reel. For the rod to remain stationary, a screwdriver or other suitable object is inserted into this hole, and with unhurried rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (left-hand thread) and removed from the trimmer.

How to replace line in any trimmer

Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work.

Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the vegetation being cut, is either a mowing head or a milling disc. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends.

How to properly wind the line on the reel? Understanding.

So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of fishing line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• one groove. both antennae are wound together in one groove;
• two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Single-barbed trimmer spool

Brushcutter reel with one antenna

Many owners and experts note the ease of use and ease of refueling the single-whisker bobbin. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

• small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
• electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
• electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Calm trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

We carry out the winding of the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound on its own inside. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.

A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.

In this manual, we will walk you through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference is that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.

How to wind the line around the trimmer cutter head or brushcutters

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
• A small section of the line is left free to bring it out. it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

How to tuck the line into the trimmer?

In order for the area near the house to always look well-groomed and neat, it must be cut regularly. Fortunately, modern technology allows you to solve this problem without excessive physical effort. Electric trimmers are so easy to operate and maintain that even a teenager can use them to mow. The main thing is to figure out in advance how to fill the line in the trimmer.

How to load the line into the trimmer?

So, our task is to properly load the line into the trimmer. Let’s take a closer look at where to start its implementation and what pitfalls can await us in the process.

Step 1. choosing the line

Step 2. remove the coil from the trimmer

To perform this operation, the trimmer must be disconnected from the mains and turned over with the working head up. The further course of action depends on the trimmer model and the design of the coil itself:

• for small trimmers with a lower engine position, press on the keys on the sides of the coil and remove its upper part from the head;
• on trimmers with a curved bar, we clamp the coil body with one hand, while simultaneously turning the winglet located on the body counterclockwise;
• for trimmers with a straight bar and a gearbox, insert a screwdriver into the hole located under the coil, and then turn the coil body counterclockwise.

Step 3. disassemble the coil

After the coil is removed from the head, it must be carefully disassembled. It is better to do this on an already mown area, since there may be a spring inside the coil, which will be quite difficult to find in tall grass. After disassembly, we will have three parts on our hands: the body (top cover), the protective casing and the coil itself.

Step 4. measure the required amount of fishing line

Newbie mowers are usually interested in how many meters of line to wind on the trimmer reel? There are two ways to solve this issue:

• Unwind a skein of line on a flat, dry place and separate half of it.
• Measure 3-4 meters of line from the skein.

In any case, after the end of winding, the turns of the line should be on the body of the reel, without sliding off it. You do not need to try to wind as much as possible, as the line will unwind poorly and tear more often.

Step 5. winding the line onto the reel

How to attach the line to the trimmer depends on the coil design. Consider the option when the reel body has one outlet for the line. In this case, the end of the line is clamped in the crevice of the coil, and then we wind the line, trying to lay the turns as tightly as possible. The direction of laying the turns should be opposite to the direction of rotation of the coil and is usually indicated on its inner part. After the end of winding on the reel, you must put on a protective casing and bring the end of the line into it.

If the reel is designed to work with two tails, then the line must be folded in half and laid in the groove in the center of the reel. Further winding will be carried out along one or two slots, depending on the coil design. The direction of winding must also be opposite to the direction of rotation of the coil. At the end of the ponytail, the line will also need to be led out into the holes on the top of the reel.

How to wind the line onto the trimmer spool

How to Wrap the Line on a Trimmer Spool Correctly. Step-by-Step Guide VIDEO

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly in the clockwise direction.

Unscrew the cover according to the direction indicated on the body.

Remove the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

How to choose a fishing line. length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him.

As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

Winding Algorithm

Insert the resulting loop into the groove.

Lay the line in the direction indicated on the element body.

Insert the short end into the slot on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of coiled line into the spool body.

Pull the line out of the locking grooves.

How to replace string trimmer line

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now it remains only to screw the bobbin onto the trimmer and you can work.

ATTENTION! Typical line problems

No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem	Cause	Decision
Line break	Stones, branches and solid objects in the grass	Avoid collision
	Poor cord quality	Replace with a quality analogue
	Head outlet wear	Complete replacement of part required
The line is unwound	The spring in the coil is weakened	Check spring and replace if damaged
The line is sticking	Poor line quality, due to which it can melt under the influence of temperature from the heating head	Reel in less line or replace with a better line

For a better understanding of the mechanism of the process of changing the line in the spool with a video guide prepared by FUBAG specialists:

How to wind the line correctly on the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. This is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this painful question. Explore the article and find out how the line winds on the trimmer reel.

The order of winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

So how do you load the line into the trimmer reel? All work is divided into several stages:

When you turn on the trimmer, the excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

• fishing line comes in different thicknesses and with different sections. The best option for winding is the “native” line for this model;
• never use fishing line or metal cables for the trimmer. Such a substitution may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawnmower himself, but also those around him;
• the line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
• Use regular line for cutting lawn grass and pigtail line for coarse weeds. It is more durable and will not constantly cut.