How to install a Lifan engine on a single-axle tractor Cascade

Choosing an engine for a walk-behind tractor Cascade

install, lifan, engine, single-axle

Auto mechanic specializing in agricultural machinery

Lifan 125cc Engine install | UNBOXING

One of the most common technical devices to help farmers plant and harvest crops is the Cascade single-axle tractor. Units of this Russian brand have established themselves as reliable, strong and durable products.

Motoblocks are very easy to use. They have a handlebar that can be adjusted horizontally and in height. The center of gravity is close to the ground, which reduces the effort when cultivating the soil.

These walk-behind tractors are one of the most practical

Common questions

Characteristics:

Power 6.5 hp.
engine‘s type 4-stroke, single-cylinder engine
Cooling Air
Starter Manual
Fuel tank capacity 3.6 l
Oil capacity 0.6 l
Fuel type Petrol
Fuel consumption 395 g / (kWh)
Direction of rotation of the shaft Counterclock-wise
Motor output shaft diameter 20 mm
Shaft location Horizontal
Working volume 196 cm3
Max. torque 10/2500 N.m / rpm.
Maximum power output at 3600 rpm 4.8kw
Engine mount type Under the key
Shaft length 50 mm
The engine is suitable for Snow blower
The engine is suitable for single-axle tractor with belt (chain) coupling
Weight 16 Kg
Guarantee 12 months.

cascade with the G200 engine champion. Youtube

cascade with the G200 engine champion. Installation of the Lifan F 170 R engine on the Cascade engine block. Duration: 5:34. Yuri Rogotsky.

Chinese engine on the Cascade | Thread Starter: Gennady

Good day to all! I am installing the new Lifan 168 engine on my old cascading shaggy year, but this is not how I cant figure out how to connect the throttle cable.

Pavel Not all gardeners understand the mechanics that I don’t know, Cascade. what’s this? Tractor?

Roman When my Texas Lilly failed with a Briggs-Stratton engine, I had to turn it over for repairs and had to plow it urgently. The site was catastrophically overgrown with weeds. I was offered a Chinese TG engine at a service center. The repairman had to connect the gas cable “opposite”. the maximum throttle was obtained using the Stop position. When BriggsStratton repaired, and TG, on the contrary, took action. I myself put Briggs Stratton in his place. How to connect the cable. I don’t remember and now I was just translating the throttle grip, which is on the engine, not with a cable, but with one hand. This does not create much inconvenience: in fact, a beater motor. not a car, smooth throttle control during operation is not required, the regulator is only in two positions. either “full throttle” or “stop”.

Maxim, if you give full throttle, you simply cannot catch it. we are on the rise with the subara engine we are in second gear

Which imported engine can be put on the roller from a walk-behind tractor? What is an engine and what is the cost? | | Thread Starter: Ruslan

Good day to all! I am installing the new Lifan 168 engine on my old cascading shaggy year, but this is not how I cannot figure out how to connect the throttle cable. Help me understand.

Vadim Look at the Subarovski engine. It is very easy to run, economical, there is no oil at all and costs 5 horses about 14 thousand.

single-axle tractor, engine replacement for Chinese Lifan / Motoblock, udskiftning af motoren til den kinesiske Lifan

single-axle tractor, engine replacement for Chinese Lifan / Motoblock, udskiftning af motoren til den kinesiske Lifan single-axle tractor MB-1, aka

Honda engine advantages

  • Have a high power, from 1.5 to 12 hp.
  • Have high performance.
  • Engines of this company are equipped with a splash lubrication system, which will significantly increase the resource of the motor.
  • They have forced air cooling, which will allow the engine to run longer.Thanks to this system, the engine does not overheat.
  • Starting the engine after a standstill is quick and easy thanks to the automatic decompressors. The system is started manually and the start time does not depend on weather conditions;
  • Honda engines are reliable and economical, meet environmental standards.

How to change the engine on the Neva walk-behind tractor: we consider it thoroughly

In order to facilitate the work related to land plots, each of their owners tries to purchase a single-axle tractor for themselves. Among all existing motoblocks, the most widespread are “Neva”.

Engine for the Neva MB 2 walk-behind tractor

The engine for the single-axle tractor Neva MB 2 is a device with a capacity of 6.5 l / s and a volume of 208 cc. The gearbox in this model works on a gear-chain principle and is equipped with an additional range of gears of a reduced type.

Very often this type is used as an assistant in the transportation of goods, but it is also used for hilling, plowing, cultivation on all types of soil, even on the most difficult.

How to adjust the valves?

After a certain period, it is necessary to adjust the Lifan engine on the walk-behind tractor, because failures occur, that is, it starts to work incorrectly. In fact, there are not so many problems on which the unit may behave incorrectly. One of the main ones is incorrect valve adjustment. It is quite simple to produce it, all work is performed in several stages:

2010 Mack CXU612 Single Axle Tractor Truck

  • The valve cover is removed.
  • The gap, as a rule, is, according to all standards, from 0.02 to 0.12 mm, so you need to take some kind of measuring probe or device for accurate alignment.
  • Further, the adjustment itself is carried out using a screwdriver and a measuring probe, which should be placed under the valve. The screwdriver, in turn, unscrews the adjusting screw.
  • After adjustment, you must return the cover to its place.

Engine service

During operation, there should not be any significant problems in the case of a completely serviceable new engine, while it is better to check it at maximum power within the warranty period. Engine maintenance is carried out by the owner himself, although with Lifan engines on walk-behind tractors there should not be any problems with this.

If you still have problems, you need to perform a number of simple procedures, after which engine will work “like new” again:

  • Replace candles.
  • Change oil.
  • Check the integrity of all connections.

No more adjustments are required, since the ignition in such engines is electronic. After completing the above steps, you can try to start the engine.

Usually, running in an engine takes a long time, but if you do everything in accordance with the manual, then no problems should arise, and if they do, it is important to remember that this is a new engine and this means that it is under warranty. It will be easily replaced with a new one or at least repaired.

Repair of a walk-behind tractor

If it is not possible to start the Lifan engine installed on a single-axle tractor, then it is worth performing an ordinary check. For this purpose, you need to perform a series of actions, during which it is easy to find the cause of the motor malfunction and simply remove it:

  • Check the petrol supply. The engine can “grab”, but not start, as the gasoline is not sucked out of the tank well. The reason may lie in the clogging of the drainage hole in the plug, which serves to allow additional air to enter the tank, instead of gasoline, which leaves there. The hose could be clogged with debris, or something could get into the tank itself. It is necessary to check our client is left with probable options.
  • Check the spark plug. If she smoked, as it is also called, it completely struck her, then you need to change it, since it cannot be repaired.

After eliminating these defects, you can try to start the engine. If this does not help, then the reason must be found in the unit itself.

When the candles are still wet

  • Carbon deposits on spark plugs. Clean them with a rough surface and wash.
  • The gap between the electrodes is increased or decreased. You need to adjust it to the required size.
  • The insulation of the wiring is damaged. It is usually replaced with a new one.
  • There was a short circuit of the mass on the STOP button.
  • The starter of the ignition system is faulty.

The rubber seals on the carburetor may also loosen, causing air to be sucked in. It is necessary to tighten the bolts, candles and inspect the gaskets between the cylinder and the candle head.

Another option for poor engine starting may be that the carburetor choke does not close completely.

The candles in the walk-behind tractor should not be wet

If the compression is broken, it will also be difficult to start the engine. The reasons are: carbon deposits on the valves, the inlet valve is deformed, or the piston rings are already worn out.

Malfunctions in the course of operation usually appear when the nodal connections of the engine, being exposed to overloads, fail, which leads to malfunctions.

Important! If you understand that the motor starts to make noise, work in jerks, you should immediately turn it off and cool it down, only then try to repair it.

When the engine began to pick up and decrease speed by itself, this is possible by loosening the traction and fastening the levers. To eliminate it, simply adjust the control drive.

If the engine loses power, it means that it is overheated. In this case, the motor can jam, which happens when the oil level in the crankcase is low, a nadir forms on the connecting rod head, or the oil sprinkler has become unusable.

Engine service

In the process of use, there should not appear any significant problems for which a design with a one hundred percent serviceable new engine is intended, with all this it is better to check it at the highest power during the warranty period. The service of the motor is carried out by the owner without the help of others, although with Lifan engines on walk-behind tractors there should not be any problems with this.

If, nevertheless, there are tasks, you need to perform a number of simple procedures, after which the engine will work again “like new”:

  • Change candles.
  • Change oil.
  • Check the integrity of all connections.

New Lifan 125 set up

It’s not just that no adjustments are needed, because the ignition in such engines is electric. After completing the above actions, of course, try to start the engine.

Lifan

Lifan engines help to solve many tasks of land cultivation, planting vegetables, harvesting.

Lifan is a company from China, was established in 1992 and has proven itself well. The company is engaged in the production of not only engines, but also cars, motorcycles and other units.

In the Russian market, this brand is famous for the details for the walk-behind tractor, since many land owners use this technique.

If earlier products from China raised concerns due to poor quality, now the situation has changed, which contributes to the massive distribution of the Lifan brand.

The company’s engines for a single-axle tractor have different characteristics, so each model corresponds to a specific unit. It all depends on the mounts. You can choose compatible devices either yourself or entrust this choice to specialists.

Power is usually measured in horsepower. The most popular engine has 6.5 hp, which is enough for all the work. To save money, you need to decide for what tasks the single-axle tractor will be used. Average, which is considered a very inexpensive purchase when compared with other manufacturers.

The process of installing a Lifan engine on a single-axle tractor Cascade is simple:

  • Remove your used engine. This can be done with ordinary open-end wrenches and heads. Disconnect the cables for gas, throw off the belt that transmits torque to the gearbox.
  • Supply a Lifan brand device. Assemble in the reverse order. If the fasteners do not match, they must be redone by drilling new holes or welding metal plates.

Since the single-axle tractor Cascade has compact dimensions, the Lifan part is well suited for this particular unit when working on personal plots and vegetable gardens.

The engines themselves are developed by Japanese engineers, and the Chinese industry has only adopted their experience. Also, the devices can be used in generators, as they are very reliable and durable.

Which imported engine can be put on the roller from a walk-behind tractor? What is an engine and what is the cost? | | Thread Starter: Ruslan

Good day to all! I am installing the new Lifan 168 engine on my old cascading shaggy year, but this is not how I cannot figure out how to connect the throttle cable. Help me understand.

Vadim Look at the Subarovski engine. It is very easy to run, economical, there is no oil at all and costs 5 horses about 14 thousand.

Engines from the Lifan company, what is it?

The Chinese company Lifan has existed for quite a long time, because the company was based in 1992 and continues to develop right up to the present day. With all this, “Lifan” is considered one of the main, to be more precise, one of the leading companies in the Chinese motor market.

By itself, the company develops not only engines. Her specialization is the creation of cars, bikes and other motor equipment. The company has really extensive experience in the development of engines for various equipment.

Fuel system problems

The first step is to check the spark plugs. If they are dry, it may mean that gasoline is not getting to the engine. The main reasons will be: lack of fuel, the feed valve was closed, the hole in the tank plug is clogged, unnecessary objects get into the fuel system.

  • refuel a uniaxial tractor;
  • unscrew the fuel supply valve;
  • clean the gas tank cap;
  • remove all gasoline from the tank, after removing the fuel cock, and wash it with clean fuel. Then purge the jets in the carburetor using the fuel pump.