How to Lay a Fishing Line on a Trimmer Reel Correctly
How to wind a fishing line on a trimmer: examples and recommendations
As a rule, before going fishing, you need to check all the gear, the reliability of the connecting loops and the sharpness of the hooks. But do not forget about backing, which is wound on a reel, because the success of fishing in general will depend on how to wind the fishing line on the trimmer. Incorrectly wound, it can lead to a beard, which is quite difficult to unravel and which takes a huge amount of precious time, casting distance can be significantly reduced, and in general in such a situation it is better not to fish.
Coil selection
Beginning fishermen, due to their inexperience, pay little attention to the choice of fishing rods and tackle, but the right equipment is the key to success in fishing. Spools with a spool size from 2000 to 3000, which can accommodate 100 meters of fishing line number from 0.2 to 0.3 mm, are usually purchased.
In addition to sizes, they differ from each other in the way they are wound on a spool. You can rewind the fishing line on the trimmer coil with a straight, cylindrical or conical laying, it all depends on the model. It is also worth paying attention to the country producing fishing gear. If the reel is of Chinese origin, from a cheap series, then always be prepared to entangle the fishing line during casting and the appearance of a beard, in addition, the cheap option quickly fails and requires repair or replacement.
With high-quality winding, fluorocarbon must form strictly parallel stacking relative to the spool with the direct winding method, and inclined with a cone.
How to fix the thread on the trimmer
Winding fishing line on a trimmer. simple business, but requiring a certain skill. First you need to firmly fix the reel to the rod. After that, pass one end of the fluorocarbon through all the ears of the rod and fix it on the spool. To do this, raise the coil of the reel, wrap it around the fishing line and tie it with an Arbor knot.
If the thread is hard or thick, then before winding it should be lowered into warm water, after this procedure it will become more elastic and lie more evenly. When winding, it is desirable that there is an assistant who would hold a bobbin with fishing line. In the process, lightly brake the fluorocarbon with your finger or a soft cloth.
What should be the length of the working thread
It all depends on the method of fishing and the reservoir. If fishing requires a small length of fishing line, then it should be less, if long-range casting is required, then more fluorocarbon is needed. For quick replacement in traveling conditions, every fisherman needs to know how to change the fishing line on the trimmer. If the reel spool is deep, then approximately two-thirds must be filled with cheaper thread, and the working fluorocarbon, which is necessary directly for fishing, should be wound on the remaining part. The winding should consist of a thinner fishing line than the working one, this will increase the density and not fall through the main one.
How to wind a fishing line on a trimmer
During winding, the handle of the coil should be twisted smoothly, without jerking and at high speeds. It is necessary to ensure that the thread lies in even parallel lines. Do not wind a line that is too thick for the reel.
Gently winding fluorocarbon, you should pay attention to how much is left to the side. The optimal distance is 2 mm from the top layer to the edge of the rim.
Backing
Every fisherman must know how to wind a fishing line on a trimmer and what backing is. Backing is reeling on a spool of a reel. For this, a thread with a diameter of 0.1 to 0.3 mm is often used. If a thicker fluorocarbon is used as a winding, this can lead to uneven and uneven stacking of the main fishing line. It is extremely undesirable to use wet materials for backing, such as nylon and cotton threads. They are unable to dry completely for a long time, which leads to debate, and replacing the fishing line on the trimmer. this is an additional financial cost.
The amount of thread needed for backing can only be determined empirically. This will require two spools. First, the necessary amount of working line is wound on one, and then backing is wound so that two millimeters remain to the edges of the side. After this procedure, the spool with wound fluorocarbon is removed and put on an empty thread, on which the thread is wound, only in the reverse order. first backing, then working nylon.
Spooling Nylon Thread
How to wind a fishing line on a trimmer. figured out, now let’s talk about storing fishing gear, in particular fluorocarbon on the spool. For a long service life of the thread, you should adhere to several rules, the implementation of which allows you to save money on the purchase of new equipment.
It is important to remember that after fishing, the fishing line and parts of the reel get wet, they should be well dried. Poorly dried fluorocarbon quickly fades and becomes unusable. It becomes brittle and can break at the most crucial moment. To prevent this, after seasonal fishing, the line from the reel should be reeled up and spread on the floor so that it dries well. This procedure should be carried out with backing (winding). You can dry a nylon thread after each fishing trip, if you go to it once a month.
You already know how to change the fishing line on the trimmer, it will not be difficult. Always store fishing equipment in a dry place, this will guarantee the reliability and durability.
Add a comment
How to thread fishing line into the trimmer coil
Video: How to Lay a Fishing Line on a Trimmer Reel Correctly
Coils exist different. For a coil working with one antennae, it is easier to refill a fishing line than with others. In the inner part of the reel there is a hole designed to fix the fishing line. You need to insert the tip of the fishing line into it and start winding it.
Important. you need to wind in the opposite direction from the rotation of the coil on the trimmer. Look carefully, most likely in the same place, on the reel, the direction will be indicated with a stick where to wind. It can take about two to four meters of fishing line to wind. it depends on the size of the reel itself. At the end of winding, a small piece should be left free. He will come out. In order to clamp it, there is a groove, which is also located on the inner surface of the coil. This groove firmly fixes the end of the fishing line and prevents it from unwinding when assembling the reel. If the design of the reel does not provide for this groove, then hold the end of the fishing line with your hands yourself. Now you can attach the outer part of the coil. It also has a hole in which you need to thread the outer piece of your fishing line. Now you can return the assembled coil to its place on the trimmer.
Now about the coils, designed to work with two antennae. First you need to see how many reels there are for fishing line on the reel. The presence of either one or two in different designs of coils. And then it already becomes clear how it will be necessary to reel. two antennae at once in one groove, or # 8212; each antennae is separate. Please note that if there is one groove in your reel, the fishing line hole must be through. Now you need to rewind the fishing line about 2-4 meters and pass it through this hole so that the fishing line is the same on one side and the other. Now look again, there will be an arrow indicating where to wind. The direction is against the direction of rotation of the coil on the trimmer. Winding two tendrils of fishing line at once, together. Leave the small ends. If there are special grooves. we clamp in them, if not. then just hold tightly with your hand, with your finger. There will be two holes in the outer case of the reel. a separate line for each end of the line. They did it, assembled the coil and put it on the trimmer.
If you have a reel with two grooves, then the rewound piece of fishing line (all the same 2-4 meters) needs to be folded in two, and in the special groove (it should be located just between the grooves), insert the bend of the fishing line, that is, the middle, folding her in the shape of a loop. Winding, as in the previous case, you need both fishing lines at once, only this time. each in a separate groove. And then. as described above. fixed, attached the upper case, secured the coil to the trimmer.
Another variety of coils is with a through hole on its inside. There are holes on the outer casing. That is, it turns out that the fishing line needs to be passed through these holes in both the inside and the outside, and immediately assemble the coil. And for winding use a button (this is the same button that is used to release the fishing line during operation). Just to rewind the fishing line now you need to rotate this button. over, the mechanism of this button is designed in such a way that you can twist it in only one direction, just the direction you need.
The thread for the trimmer can be divided into types according to its diameter. It can begin with the smallest. 1.2 millimeters and go up to 4 millimeters. The most commonly used is a diameter of 2 millimeters. But it is necessary to select it strictly individually, based on the specific model of the device. Often the required diameter of the product is indicated in the passport on the product. Usually the more powerful the trimmer, the larger the diameter of the fishing line should be. For example, it is better to wind a thread with a diameter of 2.4 mm on a coil of a Lawn Mower, and for a product with a weak engine, a diameter of a thread of 1.6 mm is suitable.
Except the sizes. they differ from each other by the way of winding on the spool. You can wind the line onto the trimmer coil straight. cylindrical or conical closing. it all depends on the model. It is also worth paying attention to the country producing fishing gear. If the coil is of Chinese origin. with cheap series. then always be prepared to entangle fishing line when casting and the appearance of a beard. Besides. the cheap option quickly fails and requires repair or replacement.
Every fisherman should know how to wind a fishing line on a trimmer and such a buckingham. Buckingham. This is winding on the spool of the coil. For this, a thread with a diameter of 0.1 to 0.3 mm is most often used. If a thicker fluorocarbon is used as a winding, this can lead to uneven and uneven stacking of the main fishing line. It is extremely undesirable for Buckingham to use wet materials, such as nylon and cotton threads. They are able to dry completely over time, which leads to debate, and replacing the fishing line with trimmers. this is an additional financial cost.
It all depends on the method of fishing and ponds. If you need a small fishing line for fishing, then it should be less, if you need far casting, then fluorocarbon needs more. For quick replacement in traveling conditions, every fisherman needs to know how to change the fishing line for a trimmer. If the reel spool is deep, then about two-thirds must be filled with cheaper thread, while the remaining part should be wound with working fluorocarbon, which is necessary directly for fishing. The winding should consist of a thinner fishing line than the worker, this will increase the density and not fall through the main one.
Winding fishing line on a trimmer. simple business. but requires some skill. First you need to firmly fix the reel to the rod. Then stretch one end of the fluorocarbon through all the ears of the rod and fix it on the spools. To do this, raise the coil of the coil. wrap around the fishing line and tie a knot Arbor.
Structurally, the trimmer consists of an engine. rod and working body. which, depending on the mowed vegetation, is either a mowing head. or disk milling cutter. And if with a milling cutter more and more. less clear. then with the nozzle sometimes questions arise. Usually. they appear then. when the fishing line ends.
If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound with this same groove. If there are two grooves. then each antennae wraps around its groove. In reels with one groove there should be a through hole in which the fishing line is passed. Unwind 2-4 m of fishing line, pull it through this hole so that on each side of the fishing line sticks out equally. And the tent simultaneously both antennae fishing line in the same direction, the opposite direction of rotation of the reel to the trimmer and coincides with the direction indicated by the arrow on the inside of the reel. We leave a little fishing line unwound, we fix the end we get in special grooves, and if they are not there. hold with your fingers. We pull both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.
Before winding the fishing line on the trimmer. pay attention to that. that the coil may consist of two parts. In this case, one part of the thread is wound on one side. and the second one. to another. After that, it is necessary to install the coil back and fix the cover. It should be noted. that it may have left-handed thread. This is done for that. so that the lid cannot open and slide off the device during operation.
The trimmer is one of the main tools for lawn care in the garden. Therefore, it must always be operational. Sometimes you have to change some elements of the device. For instance. it is good for gardeners to know. how to wind a fishing line on a trimmer.
And since there are not many options on the market, at the stage of selection there may be such a problem that you can simply not choose the fishing line or disc correctly when the diameter of the fishing line is not suitable for your model of Lawn Mower or in general. the disk will be with a different bore diameter. So at this stage you need to be careful and attentive.
Engineers the developers. which create new models of trimmers, clearly calculate the diameter (thickness) of the fishing line and the number of knife blades. according to the power of the trimmers. Otherwise, the engine is overloaded. resulting in damage to it. And these are additional and substantial expenses.
The opposite is also possible. when the line does not feed when the semi-automatic mowing head hits the ground This can be caused by improperly-wound fishing lines. so and so. that after installing the trimmer just forgot to pull the end of the cord from the retaining grooves on the spools.
Trimmer Heads. often also called a mowing head. is a specially designed coil. inside which a cord of a certain length is placed. A piece of cord of 8-15 m is wound onto the inner spool. The ends of which are pulled out of the coil to the required length as they wear or break off when they encounter an obstacle that is too hard.
For others, it is enough to touch the mower coil on the ground. In this case, by pressing a special button when it is struck, the anchor mechanism is released and the cord is fed due to centrifugal force. Extension of fishing line is carried out when the trimmer is working.
A classic cutting tool for all types of tools has a special trimmer line or cord. also sometimes called a string. Its thickness (diameter) ranges from 1.2 to 4 mm. For each trimmer, the maximum cord thickness is indicated. which can be operated without overheating of the engine and accelerated wear of the bushings.