How To Line The Trimmer Stihl 38

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to insert line into the trimmer spool? Instructions

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

How to thread the line into the Stihl trimmer spool

The trimmer is one of the most common tools that you can use to quickly and easily cut grass, small shrubs, lawn grass and other weeds. It’s not a secret for anyone that in order for the mowing of grass to be successful, it is necessary to use the tool correctly and correctly handle individual cutting elements.

It doesn’t matter what fuel they use in trimmers, special cutting attachments (knives, discs) are used, and some trimmers are supplied to the market in the heads of which a cutting element such as a fishing line is installed, and therefore many are wondering how to fill the line into the trimmer spool Stihl, if there are no skills as such.

Cutting attachments in the form of knives can be sharpened, but the fishing line (also cutting elements), but tends to be consumed. Below we will talk about how to properly thread the cutting element into the Stihl trimmer spool. fishing line.

Articles

A couple of tips

If the line was wound correctly by you, then when you press the bobbin button, the cutting element should be automatically pulled out. The line for your mowing device is one of the most important elements, without which the trimmer can lose all its functionality. You can say that the line (cutting element) is the heart of your mower. Therefore, when buying a fishing line, Paying first of all to its quality. When purchasing a line of one or another company, be sure to compare it with the quality of an old line.

Preparing the trimmer spool for winding

Initially, as a rule, the coil is installed to the head of the device itself. The coil consists of two parts. a cover and a spring.

Whatever company you have a trimmer, the preparation steps are the same for all types. Let’s disassemble the device, or rather, remove the coil from the trimmer head. To do this, press until the stop on the latches located on the sides of the head body, and turn the head clockwise.
To open the mowing head without problems, press the side latches, if you cannot do this with your hands, use a flat screwdriver to help. We take out the coil from the head.
In order to choose the right line for your equipment, there should be numbers on the inside of the reel, which indicate the thickness and type of acceptable line. All designations are indicated, as a rule, in millimeters.
If you did NOT find any numbers, then the maximum allowable line diameter can be determined by the through hole for inserting the line. The line should run smoothly back and forth.

The process of winding the line to the reel

After all the preparatory actions, we need to correctly determine how exactly the fishing line will be washed on your device, by turning the lid or in the opposite direction.
Measure out about 7 mm of cutting material and insert it into the hole of the bobbin with one end. It is worth noting that the line is wound exactly on the style mower model on both sides. The direction of winding the line in such models is indicated on the bobbin itself.
The line is brought out to about 17 cm freely so that weeds can be cut off with the ends. We add that it is not worth winding the line on a reel of great length. Leave a distance of about 5 mm from the line to the edge of the spool.
The two ends of the line are inserted into the holes in the bobbin. Both THESE ends Must be securely attached to the device body.
The springs extracted from the coil (if any) are inserted in the same way as they were removed, i.e. Into the bobbin and the head body itself.
To determine if you have correctly inserted the line into the trimmer, you need the element (bobbin) itself to be easily inserted into the head body of your device. If necessary, pull the free ends of the line outward still. To achieve this, you need to pull the line out of the groove with a sharp movement through the holes in the bobbin.

So, let’s say you figured out how quickly, and most importantly, to correctly wind the line on the Stihl trimmer reel. All you have to do is insert everything correctly into the grooves and fix the main cover on the device. Then you can press on the bobbin itself and make counterclockwise movements until you feel the stop. If you DO NOT feel the emphasis, then most likely the line you have filled the words of the business and you will have to start everything from scratch.

What can be used instead of fishing line

If instead of a special cutting element, say a fishing line, you install a metal cable, then your trimmer can “turn” into a real dangerous weapon Not only for you and your eyes, but for all the people around you nearby. This is explained by the fact that during the trimmer operation, the steel cable will constantly work, which will lead to entanglement, and small pieces of it can scatter on all sides with great speed.
The same can happen if you use copper wire instead of a steel cable, but in this case the pieces of separation from the copper wire will be slightly larger and may cause you even more injury. And if God forbid, accidentally catch such a cutting element on the leg, then after that a deep cut in soft tissues is 100% guaranteed, and in some cases, all this can lead to amputation of small limbs (fingers) of the legs and even hands. Therefore, our advice to you: do not use any second cutting elements, except for the fishing line, for your own safety and those around you.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds without the help of others. that’s enough for the user to just fill the line correctly. How to insert line into the trimmer spool? Instruction. How to remove the spool from the trimmer? How to wind the line in order to fill the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is impossible to make the winding by mistake: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

Coil with two working tendrils

In this type of spools, you should find the number of grooves for winding the line, lying on the inside of the reel:

One groove. both tendrils are wound together along one groove;
Two grooves. each tendril is wound on a personal groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded into them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixation of the antennae and assembly of the coil is similar to the one-groove option discussed above.

The first execution of this procedure, perhaps, will seem long and rather labor-intensive, but over time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to properly replace the line in the mowing head, the reel of the STIHL FS 55 lawn mowers Winding the line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Coil with one working tendril

The most common option and easy sequence of actions:

The dimensions of the spool and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
A small section of the line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole on the outside of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

How to put line in the Stihl.FS-38 mower

I took out the mower from the barn, but there was NO line in it, I had to put the line and on the occasion removed a small

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to thread the line into the Stihl trimmer spool

How to insert line into the trimmer spool? Instructions

The guaranteed output of the factory trimmer refueling will inevitably require a line change. Having a very rough idea of how to thread the line into the trimmer reel without the help of others, the newcomers are reluctant to take up this business. How to wind the line on the trimmer reel, how to thread the line into the trimmer reel. Autocut for stihl fs 55 trimmer line threading into the trimmer reel 2 part line winding on. But with some abilities, mastering this simple teaching does not present any difficulties, and the similar annotation presented below will greatly facilitate this process.

We wind the fishing line

Automatic line winding to a spool

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to correctly replace the line in the mowing head, the reel of the STIHL FS 55 lawn mower Reel with one working barb

The most common option and easy sequence of actions:

The dimensions of the spool and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
A small section of the line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole on the outside of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

Small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on an evenly smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special lamb: in such designs, you should hold the spool in a stationary position with one hand, and turn the wing nut counterclockwise to fix the Bobbin on the bar. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
Electronic and petrol trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a leisurely rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

For the second and third version of the coil, the suspension from the structure is disassembled by different methods. In the bobbins, the lamb is turned out from the lamb, in the coils, the latches are pressed from the latch, and one part of the coil is released from the other. How to tuck the fishing line into how to properly cheap fishing line. 2. On your site. If the halves of the spool are threaded, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

How to put line in the Stihl.FS-38 mower

I took out the mower from the barn, but there was NO line in it, I had to put the line and on the occasion removed a small

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

Small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on an evenly smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special lamb: in such designs, you should hold the spool in a stationary position with one hand, and turn the wing nut counterclockwise to fix the Bobbin on the bar. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
Electronic and petrol trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a leisurely rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

Coil with one working tendril

The most common option and easy sequence of actions:

The dimensions of the spool and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
A small section of the line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole on the outside of the reel.
The bobbin halves are assembled and put on the trimmer bar.

How to properly replace the line in the mowing head, the reel of the STIHL FS 55 lawn mowers Winding the line

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

We wind the fishing line

Sluggishly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the spool. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Coil with two working tendrils

In this type of spools, you should find the number of grooves for winding the line, lying on the inside of the reel:

One groove. both tendrils are wound together along one groove;
Two grooves. each tendril is wound on a personal groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded into them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixation of the antennae and assembly of the coil is similar to the one-groove option discussed above.

The first execution of this procedure, perhaps, will seem long and rather labor-intensive, but over time and experience this task will be solved much faster and easier.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

One groove. both tendrils are wound together in one groove;
Two grooves. each tendril is wound on an individual groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

Compact Electric Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand clockwise.

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

Trimmer head with one working Mustache;
Bobbin with two tendril fishing lines;
Auto winding reel.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Sources:

http://agrarian-blog.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://trubymaster.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://pechi-sibiri.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://pechi-sibiri.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://yotools.ru/trimmeri/kak-namotat-lesku-na-katushku-trimmera-klyuchevye-momenty.html

Grass Trimmer line, stihl, trimmer