How to load line in a lawn mower

How to replace line in any trimmer

Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work.

Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the vegetation being cut, is either a mowing head or a milling disc. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends.

How to properly wind the line on the reel? Understanding.

So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of fishing line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!

How do I load the line into the trimmer spool? Video instruction

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

one groove. both antennae are wound together in one groove;
two grooves. each antenna is wound on an individual groove.

EASIEST WAY TO STRING YOUR WEED EATER

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
A small section of the line is left free to bring it out. it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

We carry out the winding of the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound on its own inside. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.

Coil with one working tendril

The most common option and easy sequence of actions:

The dimensions of the reel and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
A small section of the fishing line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole on the outside of the bobbin.
The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
electronic and gasoline trimmers with a curved shaft without the ability to install a knife, usually have spools with a special wing: in similar designs, hold the spool in a fixed position with one hand, and turn the locking reel on the shaft with the other wing nut counterclockwise. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
electronic and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. For the rod to remain stationary, a screwdriver or other suitable object is inserted into this hole, and with unhurried rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled by different methods. In bobbins with a lamb, a lamb is turned inside out, in coils with latches, the latches are pressed and one part of the coil is released from the other. How to fill the line in how to properly cheap line. 2. On your site. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

How to thread the line into the Stihl trimmer spool

How do I load the line into the trimmer spool? Video instruction

The guaranteed output of the factory trimmer refueling will inevitably require a line change. Having a very rough idea of how to thread the line into the trimmer reel without the help of others, the newcomers are reluctant to take up this business. How to wind the line on the trimmer reel, how to thread the line into the trimmer reel. Autocut for stihl fs 55 trimmer line threading into the trimmer reel 2 part line winding on. But with some abilities, mastering this simple science does not present any difficulties, and the similar annotation presented below will greatly facilitate this process.

How to put line in the Stihl.FS-38 mower

took out the mower from the barn, but there was no line in it, I had to put the line and on the occasion took off a small

We carry out the winding of the fishing line

Sluggishly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the spool. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

one groove. both antennae are wound together in one groove;
two grooves. each antenna is wound on an individual groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass) or be equipped with notches ideal for thin grass in diameter.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should take a closer look at the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

How to tuck the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models by the filament feeding system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to fill the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element must be inserted into a specially designated place, and then the cutting attachment must be wound using the visual cues on the spool indicating the direction. At the end of all the work, the lid, of course, will need to be tightened.

What is a trimmer?

This equipment is based on the following elements:

motor, the main function of which is to rotate the cutting head at the end of the rod;
directly the head, consisting of a coil, on which either a fishing line or a knife can be wound;
knives or fishing line rotating at high speed, which are the main cutting part of the device, how to load the fishing line into the trimmer will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land that is adjacent to a house with source of electrical energy. The main positive aspects of such equipment are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. There is no need to use electricity here, which has a positive effect on the functionality of such an apparatus. the cutting attachments can be changed, working with weeds of various types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in those places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular suburban area.

Line adjustment

One of the main rules when replacing and adjusting equipment is that any manipulations with the mechanism should be carried out exclusively with the engine off and the device plug disconnected from the mains.

Perhaps these tips will tell you how to tuck the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the cutting material required by the type and, of course, to determine the category of the most used trimmer.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spool of the braid makes it possible to go directly to winding the line.

The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used.

Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

Trimmer head with one working mustache;
A bobbin with two line tendrils;
Auto winding reel.

Cord breaks

If the line breaks frequently, this may be due to the following reasons:

How to replace string trimmer edger line

stones, small branches and other solid obstacles come across in the grass;
the user mows the grass close to the fence, and if it is mesh, then it breaks off the “antennae” even faster;
poor quality of the cord (it is recommended to purchase a quality one);
the outlet holes in the mowing head are worn out, due to which the line is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part is required).

How to wind the line around the trimmer cutter head or lawn mowers

The video shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.

Line winding algorithm

Depending on which trimmer model is used, the type, thickness and length of the line are selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you fill the cord, the harder and thicker grass it is able to cut.

There are 3 ways to find out which line diameter you can use on your mower.

View information on the thickness of the cord in the instructions for the device.
Look at the bobbin itself. It can contain information about the possible diameters of the line.
Insert the line into the exit hole. If it easily passes into it, then a cord of this diameter can be used.

The line is wound on a reel in the mowing head. Therefore, you first need to open it (this was discussed above). There are 2 ways to wind the cord.

Trimmer head with automatic line threading

Trimmer head types

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on.

The advantages of an automatic trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

How to wind line on a trimmer reel: key points was last modified: June 28th, 2018 by Admin

for the new 2018 trimmers

Trimmer ECHO SRM-2305SI

Trimmer ECHO SRM-350ES

Trimmer Hitachi CG22EAS

Trimmer BLACKDECKER GL8033

Hammer Trimmer MTK25B

Removing the coil from the trimmer

On small, bottom motor electric trimmers (when operating near the ground), the coil usually has two buttons on the sides.

Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound.

When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock.

Now we turn the whole coil clockwise (since the thread is left-hand) and remove it from the trimmer. Then we disassemble the coil. It can be assembled with latches or twisted with a lamb.

If the coil is on snaps, then press on the sides on the base of the snaps so that they bend and release one half of the coil body from the other. We just unscrew the lamb.

There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

Option

In this embodiment, the head is screwed onto the gearbox shaft. To remove it, you need to fix this shaft. To do this, in similar trimmers, for example, in the Huter and Champion, there is a hole through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, follow 2 easy steps.

Insert a screwdriver into the hole and lock the shaft.
Grasp the head body and start turning it clockwise. Turn in this direction for the reason that the thread cut on the shaft is left.

Sources:

http://proinstrumentinfo.ru/kak-zapravit-lesku-v-katushku-trimmera-pravilno-video/
http://trubymaster.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://www.syl.ru/article/165467/new_kak-zapravit-lesku-v-trimmer-sovetyi-po-ekspluatatsii
http://exkavatori-exmash.ru/drugoe/kak-namotat-lesku-na-katushku-trimmera-zapravit-kakaya-luchshe-pomenyat.html

Lawn Mowers lawn, line, load, mower