How to lubricate a drill drill. Dismantling the cylinder

How to lubricate a shank drill

Disputes about whether it is necessary to lubricate the drill of the perforator and how often they go constantly. The main motive of opponents of the lubricant. It stains the final finish, for example, wallpaper. In addition, the dust that has fallen into lubrication forms an abrasive. And this wears out Cartridge punch.

Nevertheless, I am sure that it is necessary to lubricate the shank of the drill, but without fanaticism. Lubricated before starting work, and for the whole day. If there is a lot of work and in intensive mode, I lubricate Once again after 4-5 hours. But as a rule, once enough.

Next, apply grease It is necessary in the storm grooves. And not where you have to, the quantity is a thin layer, without a slide. When changing the nozzle. Drill, shoulder blades, I do not lubricate. When changing the drill, I wrap the shank in a rag and put the tool in the case so that dust does not stick on it. After the work of the brown, I wipe the rag, wrap it in a rag too and put it in the case.

Now about lubrication. I strongly recommend using specialized lubrication, for example, from “Makits” or “Hilti”. They are made specifically for this. As a result of spray, there is no lubricant during work, well, or almost no, as a rule, the lubricant flows with excessive application.

But I do not advise you to use solidol or lid, solidol is not intended for such loads, but Litol, as I noticed, is noticeably worse than the same lubricant from Hilti. In addition, the tube, say, “Makits”, costs 100 rubles. Or a little more.

Lubrication, in my opinion, is needed, it increases The survivability of the Burov. And most importantly. A cartridge, the cost of which is sometimes a third of the value of the perforator.

What details in the perforator need lubrication

There are main details that need mandatory preventive maintenance.

Sights of nozzles

Sights of working tools of the tool smell whenever you have to install them. Carefully wiped before that. With intensive use of the tool, you need to watch and control the degree of lubrication of the landing site of the nozzle. There is no need to apply too much oily composition. Why this cannot be done? The lubricant will flow out, sprinkle from a rotating cartridge, as a result will be on working surfaces that are difficult to clean. The drill will rotate slower.

Gearbox

After the engine, the main in the perforator is the gearbox is considered. It works in conditions of constantly changing speed of rotation, severe friction, increased heating, penetrating small contaminants and dust. After prolonged operation, a lubricant is necessarily applied to the inner surfaces of the gearbox. This will allow protect the shafts and bearings.

Cartridge

This part has no protective coating. Before starting to work on landing surfaces, they are introduced under the replacement tool 1-2 g of cooling lubricants. Otherwise, due to shock loads and large friction, the cartridge will break. The layer of the composition will not let small particles and dust penetrate into the internal device.

How to lubricate a drill drill

The tool needs to be maintained. The higher the load, the more carefully it is necessary to select consumables. The work of the perforator is associated not only with intensive movements of its own mechanisms, replaceable nozzles also need to be processed.

When drilling or having a lot of dust, a large amount of dust is released. This negatively affects the resource of the power tool, reduces performance, reduces the accuracy of work.

In addition to constructive devices that reduce the effects of the abrasive, special lubricants are provided.

If internal consumables (on the gearbox, engine) are updated only during maintenance, then the grease for drill punch is used directly when performing work. Tool manufacturers offer branded products, but there are universal compositions.

Basic structural elements of the perforator

In order for the perforator to perform its immediate functions, it is necessary to make a certain force towards the processed surface. It is possible to get such an impulse thanks to a pneumatic or electromagnetic mechanism. The power of the instrument depends on the energy of the impact and power of the electric motor. That is, the more the indicators are in joules and watts, the more powerful the tool.

How to lubricate the details: an algorithm of actions

Lubrication tail and cartridge Do it with your own hands is very simple. It is enough to perform such actions:

• Wipe the cartridge and the tail of the drill from the pollutants (old lubrication, dust) with a rag and dust);
• Apply the appropriate composition to the tail of the nozzle or add directly to the planting nest.

You should constantly monitor the presence of lubrication, making it if necessary. Neglect of this recommendation will lead to overheating of the drill and increased wear of the cartridge. In this case, the shank may be flattened or to break away from the working part of the nozzle.

Regarding Reducer lubrication, things are a little more complicated. Most modern models are equipped with containers. In them, opening the lid, pour oil or other suitable lubricants are added. The location of the desired hole is often indicated in the instructions. There is also a lid removal scheme. The whole process goes this way:

• Remove the lid;
• Drain the remains of the old lubricant;
• Blow (for example, using a compressor) or washed the crankcase with gasoline;
• Pour new oil in the amount regulated by the operational instruction so that its level does not exceed the existing control mark;
• Put the lid in place, closing the hole.

TUTORIAL REPAIR AND MAINTENANCE OF THE HAMMER DRILL STANLEY SCH 20. DUE TO LESS GREASE

If the tool is under warranty, then you need to pour only the recommended oil. When there is no special opening to fill it, you will need disassemble the punch. In case of warranty service, it is recommended to contact the specialists of the service center on this subject.

The sequence of lubrication of the gearbox with disassembly of the perforator

If the warranty period for the perforator has expired, then you can do all the reducer’s lubrication work and independently. In this case, the following will be needed Tools and materials:

• Locksmith set (screwdrivers with different nozzles, hexagonal keys, pliers, etc.);
• Clean rags;
• Petrol;
• Suitable for the instructions type of lubrication.

Lubricate the punch gearbox, performing the necessary actions according to the following algorithm:

• Study the instructions for operation to the device used;
• Clean the body from dust, as well as from other available pollution;
• Then they start disassembling the cartridge: with the help of a screwdriver, remove the rubber and stop rings (as shown in the photographs further);
• Remove the switch of modes (in various models this is done in different ways);
• Scam with a screwdriver or hexagon, the screws are disassembled to disconnect the brushes from the collector;
• Rinse the taken parts and the body of the device from the inside from the old lubricant using Vetoshi impregnated with gasoline;
• Wipe them with a dry rag and allow them to dry;
• Lubricate the gearbox completely, as shown in the photographs further;

Lubricated elements of the gearbox mechanism

Additional recommendations

When performing independent lubrication of the gear component, you need to take into account such recommendations.

• It is necessary to remember exactly the location of the taken parts and fasteners, in order to install everything when assembly in its place and not leave unnecessary spare parts.
• To disassemble the tool to smear the gearbox, it should be only when it is completely Cook after work.
• It is not required to apply unexplored structural elements.
• The best option is the use of proprietary lubricants intended directly for the applied brand of equipment.
• It is advisable to examine the disassembled gearbox on Defects of the gears (their wear, the absence of teeth, the presence of cracks) and other elements. This will help to replace the details in time and avoid big problems in the future.

Modern perforators are quite easy to serve. The lubrication of their working nodes does not take much time. The main thing is to use the composition recommended by the instructions or suitable for its purpose (or universal) composition. During the complete disassembly of the equipment, you need to work as carefully and carefully as possible to get a quality result. Safety should also be observed by lubricating the tools disconnected from the supply network.

Lubrication replacement. Perform at home

When they talk about lubricating the tool, they mean the replacement of lubrication on certain parts. First of all, we need to lubricate the gearbox. This mechanism itself is very complicated in terms of assembly. If this element is disassembled is quite simple, then with the question of assembly after applying the compositions, considerable difficulties may occur. Therefore, all actions should be performed in the correct sequence. Before lubricating the punch, we need a certain list of materials:

Famous manufacturers, including Bosch, Makita and others, mandatory indicate in the instructions the procedure for assembling and analyzing tools, give some important recommendations and tips. The owners of such technology, even first encountered the need to perform such work, will be able to do everything as soon as possible with a minimum of time and effort costs. If you do not have detailed instructions, you need to act in accordance with the following algorithm:

The tool is carefully cleaned of dust and other contaminants When assembling and disassembling a drill, it is necessary to remember the location of all its elements

To fix the location, you can use a photo or video camera so as not to be mistaken in the future It is possible to perform all actions related to the application of a lubricant only after some time after the operation of the device, otherwise cold lubricant can cause a violation in the normal operation of the perforator when it hits hot elements Having taken out the main components, including the drill and the punch gearbox, they must be washed with spindle oil or gasoline, after it is thoroughly drained from moisture Particular attention should be paid to the gearbox. This also applies to washing gasoline, and subsequent drying Carefully inspect every detail of the perforator

There is no lubricant on some parts, from this we can conclude that it is not necessary to apply it to this element Using a proprietary grease released specifically for the perforator of your model, you will provide your tool with such important properties as moisture resistance, as well as corrosion protection. As an alternative, you can use a lubricant, the release of which is engaged in Metabo, is a reliable product that is in demand for both ordinary people and professionals After applying lubrication, the gearbox gently and carefully collects in the reverse order. If everything is done correctly and competently, the tool is already ready to work.

In addition to the gearbox, another important element is subject to compulsory and regular application of the solution. A drill drill. Lubrication on the drill for the perforator is applied to the shank of this mechanism. For this reason, the shank should be thoroughly cleaned and washed in a gasoline solution. After that, you can proceed to smear the drill, gently applying lubrication to its shank.

The gearbox and a drill punch are subject to compulsory and regularness of lubrication

In parallel, you can also treat the cartridge oil seal, which will increase its life span, and also prevent the hit of too much dust. However, it is necessary to lubricate the cartridge in only one case if a system with an open type cartridge is installed on the drill. Otherwise, the need for this operation disappears.

When you need to change the lubricant in the Ushm

The term for the next replacement of lubrication depends on the loads and intensity of Ushm use. It is usually equal to 12 months. With everyday use of a grinder with frequent overheating, the frequency of the shift is significantly reduced, at least six months.

To verify the need to make a new lubricant, the gearbox needs to be disassembled by twisting the screws on its lid. Inside there is a pair of braids. The small one is anchored and is used to act as a large, located on the secondary shaft. A grinding or cutting disk is attached to this shaft.

During operation, the lubricant when the gearbox moves over the walls of the case, drying out and forming large lumps over time. The material used for a long time overheats, becomes liquid and flows from the body. Therefore, its volume in the gearbox is reduced. If the gears have only a thin layer of the lubricant, its addition is required.

What manufacturers of lubricants are recommended

Branded lubricant can be used. That is, from those companies who produce perforators. Say, Hitachi, Metabo, Aeg, Bosch, Bosch, Intercker, Zubble. Material from companies that produce materials for lubrication can also be used. This is Xado, Ravenol, Shell and others.

Consumers are most popular with Bosch and Makita gearboxes.

When you use a tool whose quality is confirmed by a special certificate, use only lubricating the products of those brands that the manufacturer indicates. If you apply other materials, this will lead to the fact that the opportunity will be lost to carry out warranty repairs and serve a punch.

Is liletor suitable for lubrication of a perforator? This lubricant in some characteristics exceed specially designed compositions from well.Known companies. Litol is suitable for lubrication, but it needs to be changed more often.

IMPORTANT! The best grease option is still the composition indicated by the manufacturer. There will be no problems with him. And with warranty service. Too.

Grease for drill punch: how to use and what is needed for

The tool needs to be maintained. The higher the load, the more carefully it is necessary to select consumables. The work of the perforator is associated not only with intensive movements of its own mechanisms, replaceable nozzles also need to be processed.

When drilling or having a lot of dust, a large amount of dust is released. This negatively affects the resource of the power tool, reduces performance, reduces the accuracy of work.

In addition to constructive devices that reduce the effects of the abrasive, special lubricants are provided.

If internal consumables (on the gearbox, engine) are updated only during maintenance, then the grease for drill punch is used directly when performing work. Tool manufacturers offer branded products, but there are universal compositions.

Lubrication for drills of the perforator. How to use?

To do this, it is enough to squeeze the mixture from the tube to open grooves and evenly distribute it along the entire length of the groove, and for closed grooves it is necessary to make a lubricant with a napkin without leaving a “thick” layer. After the end of the work, the shank must be thoroughly wiped off so that it is clean during storage, the residual lubrication film is enough so that the metal does not rust. In addition to the Bush company, the firm’s lubricants are produced: Makita, Metaba, Intercommit.

You can buy a grease for a punch drill from any manufacturer in specialized stores or on the Internet resources of this topic by typing the name of the required tool or lubricant in the search bar.

Lubrication for a perforator. Than and how to lubricate the perforator correctly?

Review of the best reviews. Lubrication for a perforator. Than and how to lubricate the perforator correctly? In Russia list 2019. 2020.

The grease for the perforator is carried out regularly. For example, if the tool is used every day, they plan to process every 3 months. Over, individual parts, for example, a cartridge burg, are processed every month, and with intensive work-weekly. How to do this is described in detail below.

Working equipment of the perforator

The instruction to the mechanism always contains an urgent requirement to lubricate the shank of the shift tool. The drill perceives high dynamic load at the level of thousands of shocks per minute.

With constant work, the operator should regularly coat the shank of the storm with grease. Without this, the nozzle will overheat and break. Carrying for a perforator is a painstaking matter.

The correct application is carried out in the grooves, which include the wedges of the cartridge. It is important to clean them of garbage and sand, and then serve a small amount of lubricant in them. When getting a drill or crowns, you should always update a lubricant layer. A gram shares is enough.

Cartridge punch

Initially, this node does not have its own protective coating. Introduce 1-2 grams of lubricant-coching substance is required before the start of work.

Place of processing. Landing surfaces for replacement tool. It is here that tremendous friction and shock loads that can disable the cartridge arise. In addition to active protection, this achieves passive protection: the layer of substance will close the internal device from the penetration of dust and small particles.

Reducer of the perforator

This mechanism is the key in the electrical tool (after the motor, the rotation of which it transmits to the working nozzle). Reducer working conditions: constantly changing speed of rotation and torque, severe friction and increased heating from it. Penetrating dust and small pollution should be added to this. The gearbox is in constant voltage.

The lubrication of the punch reducer in the application of the substances on the inner surfaces is bonded. Especially after long operation. Bearings and shafts are protected in the same way. Lubricate the punch gearbox is important when prolonged work.

A punch grease. How to extend the life of a tool

Any technique requires proper care during operation to extend its life span. This is the most directly related to perforators, since the operation of the device is associated with a large number of rotational movements, which significantly increase the wear of the main structural elements. In addition, when drilling, a huge amount of dust is distinguished, which also negatively affects the reliability of the punch. So that work with the device does not cause difficulties even after the end of the warranty period, it is recommended to lubricate it in a timely manner. This is what our article is about.

Grease for perforators. What is its need

Lubrication for drills of the perforator, its gearbox and other elements is not much different from any other lubrication in its external characteristics. This is an oily viscous substance, the task of which is to reduce the coefficient of friction in the movement of the structural parts of the drill. It is very important to understand that the presence of lubrication allows only to reduce the wear of the mechanisms, and not to completely relieve it. Over time, the lubricant is quite saturated with dust secreted during crushing and drilling, which changes the viscosity of the lubricant. As a result, the level of wear and wear is increasingly increasing if you do not update the old grease in a timely manner.

Lubrication, like any oily viscous substance, allows you to reduce the wear of the mechanisms

One of the main parameters when choosing a lubricant is its viscosity. High.Quality products are of high prices, but it is not recommended to save here. The perforator itself belongs to the category of fairly expensive devices, so it is necessary to take care of its condition so that it fully worked the funds invested in it.

Choosing a lubricant. How to choose the right composition for a drill

It is required to choose the optimal composition for specifically your model so that the punch does not fail for a very long time. As a rule, manufacturers in the instructions clearly prescribe the time for replacing the lubricant mixture, as well as the composition suitable for these purposes. If the warranty period has not yet come out, it is necessary to use only certified compositions that were approved by the manufacturer specifically for these purposes. Otherwise, the service center may not accept the goods to fulfill its warranty obligations.

You can always seek help from a consultant to a service center and a store while buying a tool. A qualified specialist will tell you how to lubricate the perforator, how often it is necessary to do specifically for the selected model, as well as suitable lubricants.

There are universal mixtures that are lubricated most of the drills. For example, you can use ordinary oil, which is poured into diesel engines of cars. Graphite lubricants are also very popular recently, since manufacturers have worked on the quality of the goods, their viscosity and operational characteristics. Some branded compositions have much more poor properties than a composition made on the basis of graphite. In addition, the cost is within very reasonable limits, which forces people to make a choice in favor of these funds.

A lubricant called Litol-24 is suitable for perforators

For perforators, you can also use lubricants such as lutol or solidol. A solution called Litol-24 is very popular, due to the positive qualities of the composition, a low price and a long period of lubrication. However, it should be taken into account the fact that such tools have some disadvantages, for example, cause inhibition of rubbing structural elements, and also significantly overheat the device during operation.

In any case, such funds can be applied only when the warranty period has already ended. Replacement of lubrication in the tool, which is still applied to the warranty, is carried out in the service center, and on a free basis, which is logical. If you decide to carry out such a task yourself, then take care in advance about the availability of appropriate compositions. It can be a lubricant for the Makita or Bosch punch. Such compositions are highly price, but their quality is fully consistent with financial costs.

Lubrication replacement. Perform at home

When they talk about lubricating the tool, they mean the replacement of lubrication on certain parts. First of all, we need to lubricate the gearbox. This mechanism itself is very complicated in terms of assembly. If this element is disassembled is quite simple, then with the question of assembly after applying the compositions, considerable difficulties may occur. Therefore, all actions should be performed in the correct sequence. Before lubricating the punch, we need a certain list of materials:

Famous manufacturers, including Bosch, Makita and others, mandatory indicate in the instructions the procedure for assembling and analyzing tools, give some important recommendations and tips. The owners of such technology, even first encountered the need to perform such work, will be able to do everything as soon as possible with a minimum of time and effort costs. If you do not have detailed instructions, you need to act in accordance with the following algorithm:

• The tool is carefully cleaned of dust and other contaminants
• When assembling and disassembling a drill, it is necessary to remember the location of all its elements. To fix the location, you can use a photo or video camera so as not to be mistaken in the future
• It is possible to perform all actions related to the application of a lubricant only after some time after the operation of the device, otherwise cold lubricant can cause a violation in the normal operation of the perforator when it hits hot elements
• Having taken out the main components, including the drill and the punch gearbox, they must be washed with spindle oil or gasoline, after it is thoroughly drained from moisture
• Particular attention should be paid to the gearbox. This also applies to washing gasoline, and subsequent drying
• Carefully inspect every detail of the perforator. There is no lubricant on some parts, from this we can conclude that it is not necessary to apply it to this element
• Using a proprietary grease released specifically for the perforator of your model, you will provide your tool with such important properties as moisture resistance, as well as corrosion protection. As an alternative, you can use a lubricant, the release of which is engaged in Metabo, is a reliable product that is in demand for both ordinary people and professionals
• After applying lubrication, the gearbox gently and carefully collects in the reverse order. If everything is done correctly and competently, the tool is already ready to work.

Which lubricant is better to use for a perforator

A good perforator is quite decent, and at the same time saving on lubrication is really unreasonable. And the household drill with the function of the perforator requires good maintenance. Therefore, it is important to choose the right, what kind of grease you will lay in your perforator.

Over, it is not necessary to do this more often than once every half a year for a household tool.

You can choose a lubricant as a performer of a perforator, such as traditional Makita, Bosch, Metabo but also from AEG, HITACHI, IntERCOCKOL, BEA.

You can choose a lubricant from lubricant manufacturers, such as the lubricant known to many from XADO, Ravenol and others. Some experts, having a small park of power tools, and having tried some species, came to the conclusion that the lubricant that is used to lubricate the nodes in Toyota cars is best suited. This is a multi-purpose lubricant 08887-00101 Grease MP-G No. 2, which gives very good results specifically for the work of punch. The question is how to buy it.

The table more clearly shows lubricants from well.Known companies.

Litol. 24 can be used, but, as indicated in the article, with reservations.

The composition of the lubricant must meet the following requirements:

• The lubricant should stay well on the details and when working on them there should be a lubricant.
• If the tool is working in a wet room, when the tool is turned off and its cooling according to physical laws in the gearbox itself, low pressure is set and moist air as a result of this goes inside. Therefore, lubrication should be resistant to moisture and not form an emulsion.
• Heating of grease during operation, followed by its thinning, should not affect the quality of the lubricant and restore their properties after cooling.
• A property such as a droppings should withstand a high temperature.
• The lubricant should remove dust and abrasive from the place of contact of the parts on the walls of the case.
• Since the details in the case are made from different materials, for example, steel, aluminum alloys and others, lubrication should be suitable for all.

As a novelty, you can pay attention to such a lubricant as “Ultra”, which with a slight increase in temperature becomes liquid. At the same time, it has excellent adhesion.

Ultra lubricant, which can be used both sealed and leaky gearboxes.

When buying a lubricant, of course, very carefully read the instructions, and sometimes reviews for this product.

Before you are interested in how to lubricate the punch, you must correctly choose the product. Having sorted out the design of the crankcase and choosing either a liquid or a consistent version of the lubricant, you need to stop at the manufacturer. And here you can go one of two ways.

The easiest way to follow the brand. Bosch, Makita, LubCon, AEG are widely popular. In this case, you need to take the lubrication of the same manufacturer who made the tool. So the warranty is most observed that all of the above requirements will be fulfilled.

In addition, such lubricants often have accompanying documents, which even indicate specific models best compatible with the product. It happens that there is even a list of other brands whose technique can use these products. But still you need to show marginal accuracy in choosing.

You can also use universal lubricants from leading manufacturers. Companies such as Castrol, XADO, Ravenol and Shell produce a line of oils that are equally suitable for any technique. And the only condition for competent use is the presence of an indication on the packaging of the product, that this is really a lubricant for the reducer of the power tool.

The owner can only choose a consistency. And to do this correctly, the technical documentation attached to the perforator will help. There is always complete information, including recommendations for lubricating the working nodes.

How to lubricate a punch

The main purpose of the perforator is to drill, hammer and drill various surfaces. As a rule, most of the materials with which this tool has a tendency to ardent. Small particles, falling on internal parts, clog the device. It should be borne in mind that the elements are in motion, during which they are in contact with each other, which means that their abrasion may begin. To maintain the performance of the tool, it is necessary to clean it in a timely manner. Only with this departure it is possible to extend the service life as much as possible, avoid an ambulance and expensive repairs.

There are general rules for all types of perforators.

How to lubricate the punch gearbox

• So, to lubricate the gearbox, it is most often advised to use compositions in the form of liquid oil, which is poured in a certain dose into the tool body (into specially designed holes). Such oil fills the gearbox body and is reliably isolated inside with the installed covers on holes or bolts. During operation, parts are evenly covered with this tool. The most popular manufacturers of oil for lubricating gearboxes are Bosch and Makita firms.
• An example is two popular types of manufacturers data that are used in the initial assembly or during the repair of the tool:

• Lubrication “Makita P-08361” 30 ml, approximate cost 100 rubles.;
• Bosch 1615430005 oil 45 ml, price is about 300 rubles.

How to lubricate a drill drill

• The grease for drills of the perforator is used to reduce the wear of the nozzles, and also extends the operational period of the perforator (including by reducing the number of dust penetrating into the dust). Lubricants are applied before each insertion of the drill into the cartridge, for this, the nozzles of the nozzle are lubricated with a small amount. Before carrying out this operation for the first time, you need to carefully read the instructions for the tool. This is necessary in order to understand how to correctly disassemble/assemble a perforator without damaging its elements and achieve proper operation.
• The amount of lubrication and its quality depends on how the power tool will function. If the ratio is incorrectly selected, overheating of the device and even failure are possible. Therefore, before applying one or another lubricant, it is worth checking if there is a given manufacturer and the type of fund in the recommendations in the operating instructions of the perforator. The most common compounds for the grease of drills are also produced by Bosch and Makita trademarks, only funds have a thicker consistency.
• When starting to lubricate, it is necessary to rinse and blow the tool, wipe it dry and only then apply a new layer of protective equipment. Those details that do not need sliding should not be lubricated, since this can only damage the punch. Such elements include, for example, the gear council.

How to lubricate a punch cartridge

• Also, the composition should be applied to interchangeable nozzles for drill in the form of a cartridge. The amount of substance should be the same as indicated in the instructions. From its overabundance or deficiency, the tool may fail.

Choosing the type of lubricant does not make problems, there are clear recommendations in the instructions, if they are not available, then you can choose almost any funds from trusted manufacturers.

Lubricant for a perforator: for drilling and gearbox, than to lubricate, how to lubricate and use, what is needed for, composition

Separate parts of the perforator must be periodically lubricated. This reduces friction and increases the period of operation. You can do work yourself, you need to know what exactly to lubricate and how, so that the punch works for a long time. Typically, manufacturers put instructions in which it is written in detail how to care for the tool.

What is the lubricant for?

There are several types of lubricants for the perforator.

This is a certain substance that helps to reduce friction during the operation of rotating elements.

Lubrication is solid, liquid or gaseous. In cases with perforators, liquid and solid species are used.

Each manufacturer has its own operating features. A different amount of lubricant for a perforator is required. The frequency of adding lubrication also varies in each manufacturer.

It is required to process the main spinning elements, since it is they who are subject to the highest load during the operation of the device:

Important. Lubricate these elements in accordance with the instructions. The disadvantage or excess lubrication in the perforator negatively affects its functionality. Incorrect consistency of the mixture will also not give the desired effect.

It is not recommended to lubricate the elements that do not need this. The composition of the mixture does not pass air, which leads to overheating of the perforator. With prolonged use, there is a risk of short circuit. Then the repair will be expensive, it’s easier to buy a new tool.

How to lubricate each individual element

Today they use creamy lubrication and oil.

Their compositions are divided into synthetic and semi.Synthetic.

Each manufacturer of perforators has its own requirements for lubricants.

They are indicated in the instructions. Let’s figure out how to use each separately:

• For the gearbox, it is recommended to use liquid oil. It is poured in a certain amount in the case itself. If the product is not damaged, then there are covers or bolts on it that prevent the flow of a lubricant element. Makita and Bosch companies themselves produce lubricants for their products. There are also creams for gearboxes. But not all models work on a lubricant of such a consistency.
• Smill lubricant is used to reduce the level of wear of the nozzle. It reduces the amount of dust that enters the product itself during operation. Apply lubricant is required every time before work. It is important to study the instructions in order to do everything correctly. Creams are used for this part.
• It is advisable to lubricate the cartridge every time before work. Depending on the manufacturer, it is possible to use a cream of various consistency. Oil for these components is not used.

Typically, the perforator is a lubricant that is suitable in a particular case. When it ends, you need to buy the same or its analogue. A large number of lubricants for perforators are presented on the market. Their price is democratic, and they are sold in specialized stores.

When choosing an analogue, you need to pay attention to viscosity. This is the main indicator on which the duration of the operator depends.

Important. If the tool is under warranty, then for lubrication of parts it is worth contacting specialists. They will advise about the methods and frequency of preventive work, taking into account the load on the tool.

How to lubricate it correctly

For the correct application of the lubricant on the rotating parts of the perforator, you need to study the instructions. It indicates what and in what sequence you need to do. It also indicates what kind of lubrication consistency should be.

The following actions are required:

• Prepare a grease for a perforator;
• Remove rotating elements from the body and clean them from dust and dirt;
• Let the details dry;
• Apply the mixture to rotating elements in sufficient quantities;
• Gather everything in the reverse order.

Important. Excess lubricant clogs the perforator, reducing its life. Therefore, no more substance should be applied than required.

The instructions describe in detail how to perform all actions yourself. It is worth considering in more detail how to properly lubricate the main elements of the perforator.