How to lubricate a drill drill. How to remove modes switch

How to lubricate a drill drill

Greetings on my site! This article will talk about the lubrication of the perforator. The operation of this tool requires not only a simple careful attitude. Be sure to periodically lubricate the gearbox and cartridge.

At the same time, the gearbox, of course, is already coming from the factory. But over time, the lubricant leaks somewhere, somewhere dries. In addition, it is intended only to reduce friction, and not to eliminate it. Therefore, one way or another, and the details still rub against each other, which is why fine metal dust is gradually formed, which remains in grease.

As a result of such mixing of metal and lubricating material, the properties of the latter are gradually lost and the wear of the parts is accelerated.

Unlocking the Drill Bit Chuck on my Ryobi Hammer Drill

The cartridge from the plant goes dry. Here, in fact, not the cartridge itself is smeared completely, but only its place, which is in contact with the drill, since it is in it that severe friction occurs, without reducing which the cartridge itself and the tail of the drill itself can be damaged.

So, below, consider how and how to lubricate these elements. The SDS perforator will be considered with a horizontal location of the engine, since it is they who in the vast majority of cases are used by home craftsmen, and the article is mainly written for them.

What details in the perforator need lubrication

There are main details that need mandatory preventive maintenance.

Sights of nozzles

Sights of working tools of the tool smell whenever you have to install them. Carefully wiped before that. With intensive use of the tool, you need to watch and control the degree of lubrication of the landing site of the nozzle. There is no need to apply too much oily composition. Why this cannot be done? The lubricant will flow out, sprinkle from a rotating cartridge, as a result will be on working surfaces that are difficult to clean. The drill will rotate slower.

Gearbox

After the engine, the main in the perforator is the gearbox is considered. It works in conditions of constantly changing speed of rotation, severe friction, increased heating, penetrating small contaminants and dust. After prolonged operation, a lubricant is necessarily applied to the inner surfaces of the gearbox. This will allow protect the shafts and bearings.

Cartridge

This part has no protective coating. Before starting to work on landing surfaces, they are introduced under the replacement tool 1-2 g of cooling lubricants. Otherwise, due to shock loads and large friction, the cartridge will break. The layer of the composition will not let small particles and dust penetrate into the internal device.

Features of the choice of oil

Before lubricating the Bosch perforators, choose the right oil. When buying it, you need to pay attention to viscosity. High.Quality compositions are expensive, but you should not save. For such an expensive tool as a perforator must be careful constantly. What types of lubrication and how much can be used indicated in the instructions. If there is no such information, the best composition will help you choose specialists of the outlet or service center. On sale there are universal compositions for processing various models of perforators.

Many prefer to use graphite lubricants, which have:

In the absence of lubrication, you can use a single lithol or solidol. But they cause slight inhibition of rotating details and help increase the heating of the tool during operation. It is advisable to buy a special composition in the near future, remove Litol and apply a new composition.

Before lubricating the drill drill, you need to make sure that the oil taken is suitable for it. The compounds used for gearboxes are not suitable for lubrication. For the latter, take more Liquids, They must fill the free cavities, completely cover the parts that contact each other. If there are plastic elements in the gearbox, silicone grease is used. It is suitable for processing cartridges.

The transmission mechanism is allowed to lubricate plastic compositions. But not all tools when using the means of such a consistency will work uninterruptedly. Thicker mixtures are suitable to reduce the degree of wear of tail nozzles. The packaging marks their purpose for drilling. In the absence of those, you can take graphite, but they take heat worse.

Electric tool manufacturers produce their branded lubricants. They are also engaged in their manufacture by enterprises that specialize in the production of lubricating mixtures.

The most popular products of firms include:

• Bosch. For tail nozzles and gearboxes.
• Makita. For drilling.
• Interskol. For drills.
• Nanothek. For shanks.
• Turmogrease. Universal compositions.
• Lubcon Thermoplex. For gearboxes.
• Kress. To lubricate the drill.
• PRORAB. For processing seaming seats.

Lubricant for a perforator from brand Makita

Lubricate the cartridge and shank drill

This operation is very simple, so its description will be quite short.

Just take a brown lubricant and add it directly to the cartridge. Another option involves applying it to the shank followed by installing it in the cartridge nest. But no one forbids to combine these two methods for reliability.

It is necessary to ensure that the lubricant is constantly present and as necessary to add a new. If you neglect this procedure, then the tail will overheat, which will either take it off from the rest of the drill, or to flattening. Therefore, do not be lazy and add.

That’s all you need to know by the cartridge and shank.

As promised, I attach at the end of the link to the video with disconnecting the switch:

This is all the information that I have on the question of lubrication of the perforator. I hope it was clear and affordable. I say goodbye to this. Until new meetings!

How and how to lubricate the gearbox and a perforator cartridge?

Greetings on my site! This article will talk about the lubrication of the perforator. The operation of this tool requires not only a simple careful attitude. Be sure to periodically lubricate the gearbox and cartridge.

At the same time, the gearbox, of course, is already coming from the factory. But over time, the lubricant leaks somewhere, somewhere dries. In addition, it is intended only to reduce friction, and not to eliminate it. Therefore, one way or another, and the details still rub against each other, which is why fine metal dust is gradually formed, which remains in grease.

As a result of such mixing of metal and lubricating material, the properties of the latter are gradually lost and the wear of the parts is accelerated.

Inexpensive Chinese perforators can be poorly lubricated at the factory. Experienced masters of service centers recommend after buying even a new such device to immediately disassemble it and miss it

The cartridge from the plant goes dry. Here, in fact, not the cartridge itself is smeared completely, but only its place, which is in contact with the drill, since it is in it that severe friction occurs, without reducing which the cartridge itself and the tail of the drill itself can be damaged.

So, below, consider how and how to lubricate these elements. The SDS perforator will be considered with a horizontal location of the engine, since it is they who in the vast majority of cases are used by home craftsmen, and the article is mainly written for them.

Huge selection of power tools and gas equipment at low prices. Free delivery to your region. Payment upon receipt or online.

Than to lubricate the punch

Different types of lubricants are used to lubricate the gearbox and a cartridge with drill.

Lubrication for the gearbox

A special lubricant is used here, which should be called. Gearbox. It can be like under the brands under which the Perfs themselves are produced. Makita, Bosch, Aeg, etc.D. But it can also be released by a company that is engaged in this type of product, for example, Ravenol, Shell, XADO, etc.

Some use simple lilet or salutol for these purposes. But compared to special lubricating products, they dry faster, and they do not eliminate friction as it should.

Lubrication for drills

Everything is exactly the same here. Special lubricants for this purpose are called. For drills. And are also usually produced by the same firms that do punch.

For lack of special lubrication, you can use graphite. But it does not so well remove the heat from the shank, but this is important, since sometimes with prolonged work the shank happens and is flattened, which is why it is difficult to extract later.

Lubricate the gearbox

You need to disassemble the tool case. Follow the points:

• Disassemble the cartridge. To do this, first remove the rubber ring. Then pry the screwdriver and remove the locking ring. Next, the outer casing of the cartridge is carefully removed, and then the clamping ring, ball and spring are removed.
• Now disconnect the mode switch. This is done in different ways depending on the model. At the end of the article, I brought a certain number of links to the video, which tells how it is shot on a particular model. If there is no your unit among them, then you can see any similar one to understand the principle. And further, I think it will not be difficult for you to disconnect it and at yourself.
• Free from brushes collector. To do this, unscrew the back cover of the case and remove the brushes.
• Unscrew the screws that longitudinally tighten the body, and separate it.
• Remove the gearbox along with the engine anchor.

Now thoroughly rinse the gearbox itself, as well as the inner part of its body. Washing can be carried out, for example, with gasoline.

After that, first the most responsible parts are smeared. And then the entire gearbox is completely enveloped in lubricant.

Well, it remains to collect everything in the reverse order.

Lubricate the cartridge and shank drill

This operation is very simple, so its description will be quite short.

Just take a brown lubricant and add it directly to the cartridge. Another option involves applying it to the shank followed by installing it in the cartridge nest. But no one forbids to combine these two methods for reliability.

It is necessary to ensure that the lubricant is constantly present and as necessary to add a new. If you neglect this procedure, then the tail will overheat, which will either take it off from the rest of the drill, or to flattening. Therefore, do not be lazy and add.

That’s all you need to know by the cartridge and shank.

As promised, I attach at the end of the link to the video with disconnecting the switch:

This is all the information that I have on the question of lubrication of the perforator. I hope it was clear and affordable. I say goodbye to this. Until new meetings!

Basic structural elements of the perforator

In order for the perforator to perform its immediate functions, it is necessary to make a certain force towards the processed surface. It is possible to get such an impulse thanks to a pneumatic or electromagnetic mechanism. The power of the instrument depends on the energy of the impact and power of the electric motor. That is, the more the indicators are in joules and watts, the more powerful the tool.

The main elements of a perforator with an electromagnetic type of impact include:

And the elements of the tool with the pneumatic type of action include:

Pneumatic punching punctors today are more common than with an electromagnetic blow. There are several options for their execution, the main two, which differ from each other in that the first uses a swinging bearing (the so-called “drunk”), and in the second a crooked-shaped mechanism is used. Tools with the first option differ in lightness and compactness, and with the second option, as a rule, have medium or heavy weight.

• A cartridge is necessary for fixing the nozzle, several types are distinguished: SDS Plus (installed in light tools) and SDS Max (for medium and heavy devices), the first type has the ability to install a drill with a diameter of 1 cm, with the second type the tail diameter is 1. 8 cm, also SDS Plus has three operating modes (drilling, drilling, blow), and SDS max only two (drilling and blow). There is the possibility of installing a traditional cam type cartridge (a hollow cylinder with an adjusting ring and metal fists, which hold the nozzle);
• The cartridge replacement system is a quick change in one type of cartridge (SDS) to another (cam);
• Reverse. Changes the rotation of the drill, there is a brush and electronic type;
• The gearbox is a single case (crankcase), in which various gears are placed (conical, cylindrical, worm), this location of the parts allows you to protect the main mechanism from damage and dust and dust, the main function of the element is to change the speed of rotation of the shafts;
• Protection against vibration. There are passive or active (AVS marking, most heavy punch are supplied), they extinguish vibration from blows, that is, they reduce it, but it is not possible to completely remove such an effect, the active anti.Vibration system has a shock.Absorbing device. Confrontation with the spring, and The passive system is rubber overlays and a rubberized hilt, that is, it protects a little worse and is installed only on light household tools;
• Various indicators;
• Speed regulator;
• A safety coupling. It is necessary to stop the rotation of the cartridge in cases where the nozzle jams during operation, there are two types: spring.Pool (consists of half.Meters with teeth and spring) and friction (consists of disks);
• Electronic immobilizer. To stop the perforator in emergency situations, for example, in cases of voltage difference in order to avoid problems with the tool and maintain its performance;
• Engine. There are two types: transverse (vertical location, differs in a larger area for cooling and is considered more protected from dust formed during operation, as a rule, are used in cases where prolonged drilling is necessary without interruptions) and longitudinal (horizontal location helps to make the tool more balanced, that is, increases its ergonomicity, as well as more compact).

Having dealt with the device of the perforator, you should know what care the tool is needed.

Basic structural elements of the perforator

In order for the perforator to perform its immediate functions, it is necessary to make a certain force towards the processed surface. It is possible to get such an impulse thanks to a pneumatic or electromagnetic mechanism. The power of the instrument depends on the energy of the impact and power of the electric motor. That is, the more the indicators are in joules and watts, the more powerful the tool.

The main elements of a perforator with an electromagnetic type of impact include:

And the elements of the tool with the pneumatic type of action include:

Pneumatic punching punctors today are more common than with an electromagnetic blow. There are several options for their execution, the main two, which differ from each other in that the first uses a swinging bearing (the so-called “drunk”), and in the second a crooked-shaped mechanism is used. Tools with the first option differ in lightness and compactness, and with the second option, as a rule, have medium or heavy weight.

• A cartridge is necessary for fixing the nozzle, several types are distinguished: SDS Plus (installed in light tools) and SDS Max (for medium and heavy devices), the first type has the ability to install a drill with a diameter of 1 cm, with the second type the tail diameter is 1. 8 cm, also SDS Plus has three operating modes (drilling, drilling, blow), and SDS max only two (drilling and blow). There is the possibility of installing a traditional cam type cartridge (a hollow cylinder with an adjusting ring and metal fists, which hold the nozzle);
• The cartridge replacement system is a quick change in one type of cartridge (SDS) to another (cam);
• Reverse. Changes the rotation of the drill, there is a brush and electronic type;
• The gearbox is a single case (crankcase), in which various gears are placed (conical, cylindrical, worm), this location of the parts allows you to protect the main mechanism from damage and dust and dust, the main function of the element is to change the speed of rotation of the shafts;
• Protection against vibration. There are passive or active (AVS marking, most heavy punch are supplied), they extinguish vibration from blows, that is, they reduce it, but it is not possible to completely remove such an effect, the active anti.Vibration system has a shock.Absorbing device. Confrontation with the spring, and The passive system is rubber overlays and a rubberized hilt, that is, it protects a little worse and is installed only on light household tools;
• Various indicators;
• Speed regulator;
• A safety coupling. It is necessary to stop the rotation of the cartridge in cases where the nozzle jams during operation, there are two types: spring.Pool (consists of half.Meters with teeth and spring) and friction (consists of disks);
• Electronic immobilizer. To stop the perforator in emergency situations, for example, in cases of voltage difference in order to avoid problems with the tool and maintain its performance;
• Engine. There are two types: transverse (vertical location, differs in a larger area for cooling and is considered more protected from dust formed during operation, as a rule, are used in cases where prolonged drilling is necessary without interruptions) and longitudinal (horizontal location helps to make the tool more balanced, that is, increases its ergonomicity, as well as more compact).

Having dealt with the device of the perforator, you should know what care the tool is needed.

Brand lubricant materials for the working tips of the perforator

Each manufacturer of the power tool is interested in its performance, at least within the warranty period. Despite the uniform approaches to the composition of the additives, the products are slightly different.

Bosch grease for drill

Developed by order of the tool manufacturer one of the leading oil refineries. It has excellent adhesion: lubrication literally sticks to the surface and does not erase at loads. Binds abrasive dust, prevents it from acting on metal. Very small consumption.

For the Boers Makita

Produced in several packaging options. Long life: can be used for several work shifts if the boat does not change.

Neutral to rubber seals and plastic. The only problem is that the lubrication of Makita is incompatible with other compositions, so when changing the oil, thorough cleaning is required.

For boors intercol

Semi.Synthetic composition containing molybdenum, lithium. Additives provide water resistance, anti.Corrosion protection, increase the life of the tool.

Disadvantages: Low upper temperature threshold, only 130 ° C. In addition, the lubrication of the intercol quickly wear out, so the consumption is high compared to the analogues.

Bosch Hammer Drill Refreshment | Bosch GBH 2-24 DSR disassemble

There is no binding of the tool brands to lubrication. You can use the universal composition, the main thing is that the packaging has information about the purpose. To prevent the negative impact of incompatible compositions, when changing the brand, just wipe the drill dry, and cleanse the internal cavities of the cartridge.

Perforators require careful care during use. For their long.Term work, different types of lubricants are used. Compounds can be mineral, semi.Synthetic, as well as synthetic. Minerals are made from oil products, so they quickly lose their operational features, and they have to be changed quite often.

It is very important to choose a composition that will be suitable for the selected type of perforator.

How to lubricate the details: an algorithm of actions

Lubrication tail and cartridge Do it with your own hands is very simple. It is enough to perform such actions:

• Wipe the cartridge and the tail of the drill from the pollutants (old lubrication, dust) with a rag and dust);
• Apply the appropriate composition to the tail of the nozzle or add directly to the planting nest.

You should constantly monitor the presence of lubrication, making it if necessary. Neglect of this recommendation will lead to overheating of the drill and increased wear of the cartridge. In this case, the shank may be flattened or to break away from the working part of the nozzle.

Regarding Reducer lubrication, things are a little more complicated. Most modern models are equipped with containers. In them, opening the lid, pour oil or other suitable lubricants are added. The location of the desired hole is often indicated in the instructions. There is also a lid removal scheme. The whole process goes this way:

• Remove the lid;
• Drain the remains of the old lubricant;
• Blow (for example, using a compressor) or washed the crankcase with gasoline;
• Pour new oil in the amount regulated by the operational instruction so that its level does not exceed the existing control mark;
• Put the lid in place, closing the hole.

If the tool is under warranty, then you need to pour only the recommended oil. When there is no special opening to fill it, you will need disassemble the punch. In case of warranty service, it is recommended to contact the specialists of the service center on this subject.

The sequence of lubrication of the gearbox with disassembly of the perforator

If the warranty period for the perforator has expired, then you can do all the reducer’s lubrication work and independently. In this case, the following will be needed Tools and materials:

• Locksmith set (screwdrivers with different nozzles, hexagonal keys, pliers, etc.);
• Clean rags;
• Petrol;
• Suitable for the instructions type of lubrication.

Lubricate the punch gearbox, performing the necessary actions according to the following algorithm:

• Study the instructions for operation to the device used;
• Clean the body from dust, as well as from other available pollution;
• Then they start disassembling the cartridge: with the help of a screwdriver, remove the rubber and stop rings (as shown in the photographs further);
• Remove the switch of modes (in various models this is done in different ways);
• Scam with a screwdriver or hexagon, the screws are disassembled to disconnect the brushes from the collector;
• Rinse the taken parts and the body of the device from the inside from the old lubricant using Vetoshi impregnated with gasoline;
• Wipe them with a dry rag and allow them to dry;
• Lubricate the gearbox completely, as shown in the photographs further;

Lubricated elements of the gearbox mechanism

Additional recommendations

When performing independent lubrication of the gear component, you need to take into account such recommendations.

• It is necessary to remember exactly the location of the taken parts and fasteners, in order to install everything when assembly in its place and not leave unnecessary spare parts.
• To disassemble the tool to smear the gearbox, it should be only when it is completely Cook after work.
• It is not required to apply unexplored structural elements.
• The best option is the use of proprietary lubricants intended directly for the applied brand of equipment.
• It is advisable to examine the disassembled gearbox on Defects of the gears (their wear, the absence of teeth, the presence of cracks) and other elements. This will help to replace the details in time and avoid big problems in the future.

Modern perforators are quite easy to serve. The lubrication of their working nodes does not take much time. The main thing is to use the composition recommended by the instructions or suitable for its purpose (or universal) composition. During the complete disassembly of the equipment, you need to work as carefully and carefully as possible to get a quality result. Safety should also be observed by lubricating the tools disconnected from the supply network.

How to lubricate the punch gearbox and how to do it right

Perforator is a power tool that is designed to perform shockwork. To increase the service life of the power tool, you will need not only to use it for its intended purpose, but also to care for it correctly. To do this, you need the corresponding lubricant for the perforator, due to which the resource of the aggregate increases. When choosing lubricants, it will be necessary to consider that different parts of the equipment in question require appropriate lubricants.

Typically, power tools are maintained in autumn or spring, when a long leave for the device occurs or its preparation for the next season. To diagnose the power tool correctly, you must first figure out what parts on the perforator need to be lubricated. Structurally punch. A complex device consisting of a number of the following elements:

• The case is the basis of the tool inside which all the components are placed
• The electric motor is the main unit that drives the executive body of the tool. The cartridge. Puner engines have a horizontal and vertical location
• The piston system is an integral part of the gearbox, which is responsible for the formation of shock actions
• Cartridge. Has a special mechanism with quick fixation of the working nozzles
• Reducer is a mechanism that transfers rotational movements from the electric motor shaft to the tool cartridge. In the design of the gearbox there is a “drunk bearing”, which creates shock movements transmitted to the piston system
• The safety mechanism in the form of a coupling, which limits the rotation of the cartridge when jaming the working nozzle, thereby excluding the overheating of the motor
• Working nozzles are auxiliary elements that are installed in the design of the tool cartridge

To imagine what the perforator consists of, below is the diagram of the power tool.

Knowing the design of the tool under consideration, you can figure out what details of the perforator need grease. First of all, the reducer node needs a punch, the main purpose of which is to regulate the speed of rotation of the working nozzle fixed in the executive organ (cartridge). When working the tools, the gears experience large mechanical loads, which helps to increase friction. The lack of lubricants leads to an accelerated wear of the gear.

To increase the operational resource of the mechanism under consideration, you will need to regularly not only add grease to the reducer structure, but also pre.Remove the remaining old lubricants. Why is there an outdated lubricant for a perforator, not many know. It needs to be removed in order to clean the metal particles and dust, which are formed during the friction process of the gear. If you do not clean the old lubricant and apply new lubricants on top of it, then the effectiveness of such a diagnosis will be zero.

It is interesting! In the process of developing the gears, an increase in metal dust occurs, which negatively affects the operation of the parts, since due to it the friction force increases, which means that heating increases and wear is accelerated.

The gearbox or transmission mechanism in the perforator is lubricated from the plant, but you need to change the lubricant every year with the daily use of the unit. In addition to the gearbox, the tool also needs a cartridge and the seat of the installed nozzle. A drill (tail part). The cartridge (its inner part) is not lubricated from the plant, so the owner of the tool needs to be worried about this if you want to use the unit for a long time. In addition to the inside of the perforator cartridge, the shank of the installed nozzles also needs lubrication.

There are still sliding bearings in the design of the unit. They are also tested for heavy loads, therefore, in order to increase their service life, when conducting diagnostic procedures, it is necessary to add lubricants to the design of the bearings.

It is interesting! Few people know, but to improve the work of the tool, another tool knot also needs a lubricant. A collector.

Assembly of the electric part of the perforator Bosch 2-26

The assembly of the power tool, including the Bosch 2-26 punch, should be performed at the pre-prepared place. Prepare the workplace, covering the table with clean paper or a napkin. Prepare the tools necessary to perform work. From the tools you will need: screwdrivers, pliers, tester, hammer 100 g, soft metal spacers. The spacers are useful when installing bearings on the rotor and intermediate shaft of the Bosch perforator, for their nozzle.

The circuit of the electric part of the punch Bosch 2-26

Assembly of the rotor of the perforator Bosch 2-26

On a renovated or new rotor pos.803 Install the fan pos.5, and bearings poses.13.14. To lubricate the rotor bearings, use Bosch’s lubricant 1615430020.

Stator installation in the case

Installation of the stator pos.2 in the case pos.801 begin by threading through the body of connecting wires of the stator coils. The stator in the case is attached with two vones poses.80. To protect the stator from dust or dirt, a plastic cover of poses is installed on it in the case.45.

Installation of control units of a perforator

To the corps pos.801 Set the Bosch perforator button in sequentially, the contacts of poses.19 and the opener of the reverse pos.Sixteen. Make sure that all the supply wires fall into special grooves in the handle handle.

What is the frequency of the tool should be lubricated

Simple nozzles, smear the installation. Just don’t forget to first wipe the dust or other pollutants. If the work is performed intensively, then visually control the degree of lubrication of the landing site of the nozzle, which is used.

Perforator can work with different intensity. It depends on the user. Someone uses the device every day. Someone is from time to time. That is why there is no unequivocal answer about how often you need to add or change lubricants.

To decide on how often you need to change the lubricant in the general case, you need to FOCUS on the following:

Complete recommendations of manufacturers regarding the lubrication of the tool components you will find in the instructions for operation. Details that are not indicated there, no need to lubricate.

How to lubricate the gearbox

Now it is clear how to lubricate the punch inside, it remains to figure out how to properly carry out processing. Can be considered by the example of the gearbox. For work you will need:

• Peel.
• Disassemble the cartridge. They sequentially remove the rubber circle, then the locking ring.
• Remove the casing.
• Dismantle the clamping ring.
• Remove the spring and balls.
• Disassemble the case by deleting the back part.
• Dismantle the lid of the front.
• Remove the gearbox along with the shaft, switting to the “Jack of Hammer” mode.
• Thoroughly apply the composition to the entire mechanism
• Collect it, acting on the opposite algorithm.

Thus, you need to immediately decide on how to lubricate the punch. As a rule, the compositions of the same brands are used for these purposes. You can also use universal products, for example, solidol or lititol-24. A special difficulty in the work is the disassembly and assembly of the gearbox. You need to work carefully so as not to damage the mechanism.

Proper care for a drill with a perforator function

A drill that has a perforator’s function is a hybrid of two types of equipment used to create holes in various materials. Unlike a classic punch, such a drill has some constructive disadvantages, which makes its maintenance more complex and not too comfortable. Such disadvantages, in particular, include:

The main care of the drill with the functions of the perforator is that after each use of the drill of such equipment (including the tail part), it is necessary to clean well of the drilling waste, and before inserting such a tool into the drill, a small amount should be applied to its shank. Lubrication (you can use ordinary solidol). If the amount of lubricant on the shank is excessive, this will not harm the tool and the equipment used, but can negatively affect the appearance of the surface that you are drilling, since the excess lubricant will be sprayed from the rotating cartridge.

As a rule, drills with the functions of the perforator are purchased for domestic use, since their price is quite affordable, and with their functions when performing simple repair work in the house, they cope quite well. Despite the fact that these power tools are distinguished by the features mentioned above, caring for a perforator drill does not take much time and does not cause problems even not too experienced users.

Lubricants for stamping. Lubricants for cutting and stamping

A full range of lubricants designed for cutting, stamping, finishing cutting, stamping, deep hood of ferrous and non.Ferrous metals.

Description

Based on our technical experience and know-how in the field of cold stamping of metals, we offer a series CondAFORM. Designed for cutting and stamping metals.

What main technical criteria do we take into account?

• The most complex operations / improvements are required
• Metals: steel, stainless steel, copper, aluminum.
• Subsequent processing: corrosion protection, welding, degreasing, thermal degreasing, cataphoresis, gluing.
• Tolerances: random contact with foods H2, automobile industry.

How to reduce global costs?

• Increasing performance, increasing the overall efficiency of equipment
• Increases the life of the tools
• Replace clean oils with soluble.Replace chlorine.
• Auxiliary lubrication / development of the mass of deposits
• Avoid or limit subsequent degreasing procedures

Improving working conditions:

Accounting for HSE is an integral part of the technical specifications of our lubricants.Therefore, Condat offers alternative technologies and uses raw materials from biological sources.

Accompanying services

• A large assortment of lubricants designed to serve your industrial equipment:
• Equipment for the implementation of our lubricants

Features of lubricant for a perforator

The composition of the mixture should be such as to comply with the working conditions of the electrical tool under consideration. This is possible, provided that this substance will have the following characteristics:

• One of the important features of such a mixture is water resistance. The need for it occurs during breaks in the operator’s work. In this case, its temperature decreases significantly, as a result of which moisture is condensed from the air. With high humidity, this can lead to its entry into the tool and reduce the quality of its work. Waterproof lubrication will protect the metal and will not form an emulsion due to whipping parts of the tool.
• Destability to pollution helps to fight the penetration of dust into the tool. During the operation of the perforator, it is constantly among small particles, which are abandoned from the wall during operation. If the mechanism enters the mechanism, they can greatly increase friction and raise the temperature of the tool. High.Quality lubrication will help protect the mechanism from the effects of foreign particles.
• This substance should not form drops in the process. This cannot be completely avoided, since the driving parts squeeze out the lubricant outward, but the temperature of their occurrence should be quite high. Such stability will be the higher, the thicker the mixture used.
• The effect of high temperature should not be destructive for lubrication. When cooling, all properties of this substance should be restored. A lubricant that does not have sufficient resistance to heating will quickly stop performing its functions.
• A mandatory requirement is the presence of high adhesion. Since the working parts of the tool are constantly in motion, the lubricant should not jump off them when piercing holes in the wall. If the composition satisfies this condition, then in the process of working on all the necessary surfaces a sufficient lubrication layer will be preserved.
• The nodes of the perforator are usually made of alloy steel or aluminum alloys. The effect of moisture can lead to corrosion and the formation of the raid. High.Quality lubrication can establish a reliable protection of the tool from this.

A good composition must satisfy the listed requirements, but for this, the master must apply the lubricant that is designed to serve punch.